Use newly added R-Car SATA Gen2 fallback compat string
in the DT of the r8a7790 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- clock-latency = 300 us
Approximate worst-case latency to do clock transition for every
OPPs. Using an arbitrary safe value similar to r8a7791(R-Car M2) Soc.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since DVS is not supported in RZ/G1 Soc.
Note:This also fixes the below errors seen on kernel logs
[ 0.876877] cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
[ 0.883727] cpu cpu1: cpufreq_init: failed to get clk: -2
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core. Use the enable-method to point out that the APMU
should be used for SMP support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The adv7511 on the Koelsch board has a 12 MHz fixed clock
for the CEC block. Specify this in the dts to enable CEC support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) Ether/PHY pin data to the SK-RZG1E board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF2 pin data to the SK-RZG1E board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7745 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-5] devices to the r8a7743 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add pin configuration for LED0 which is connected to a GPIO.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add pin configuration for SCIF2 serial console interface.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the iwg20m board dependent part of the MMCIF0 device node.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use R-Car Gen 2 fallback binding for vind nodes in DT for r8a7794 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7794 and the
fallback binding for R-Car Gen 2
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use R-Car Gen 2 fallback binding for vind nodes in DT for r8a7791 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use R-Car Gen 2 fallback binding for vind nodes in DT for r8a7790 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the MMCIF0 device to the r8a7743 device tree.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reserve SRAM for the jump stub for CPU core bringup.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car E2 has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car M2-N has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car V2H has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car M2-W has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car H2 has 2 regions of Inter Connect RAM (72 + 4 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
RZ/G1E has 3 regions of Inter Connect RAM (72 + 4 + 256 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
RZ/G1M has 3 regions of Inter Connect RAM (72 + 4 + 256 KiB).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the iWave RainboW-G20D-Qseven board dependent part of the Ethernet
AVB device node.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Ethernet AVB support for r8a7743 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adding pinctrl support for scif0 interface.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe GPIO blocks in the R8A7743 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) Ether/PHY pin data to the SK-RZG1M board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF0 pin data to the SK-RZG1M board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7743 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
without incorporating them into the Sphinx tree. The hope is to bring some
uniformity to kernel documentation and, perhaps more importantly, have our
existing docs serve as an example of the desired formatting for those that
will be added later.
-----BEGIN PGP SIGNATURE-----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=HvQS
-----END PGP SIGNATURE-----
Merge tag 'standardize-docs' of git://git.lwn.net/linux
Pull documentation format standardization from Jonathan Corbet:
"This series converts a number of top-level documents to the RST format
without incorporating them into the Sphinx tree. The hope is to bring
some uniformity to kernel documentation and, perhaps more importantly,
have our existing docs serve as an example of the desired formatting
for those that will be added later.
Mauro has gone through and fixed up a lot of top-level documentation
files to make them conform to the RST format, but without moving or
renaming them in any way. This will help when we incorporate the ones
we want to keep into the Sphinx doctree, but the real purpose is to
bring a bit of uniformity to our documentation and let the top-level
docs serve as examples for those writing new ones"
* tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits)
docs: kprobes.txt: Fix whitespacing
tee.txt: standardize document format
cgroup-v2.txt: standardize document format
dell_rbu.txt: standardize document format
zorro.txt: standardize document format
xz.txt: standardize document format
xillybus.txt: standardize document format
vfio.txt: standardize document format
vfio-mediated-device.txt: standardize document format
unaligned-memory-access.txt: standardize document format
this_cpu_ops.txt: standardize document format
svga.txt: standardize document format
static-keys.txt: standardize document format
smsc_ece1099.txt: standardize document format
SM501.txt: standardize document format
siphash.txt: standardize document format
sgi-ioc4.txt: standardize document format
SAK.txt: standardize document format
rpmsg.txt: standardize document format
robust-futexes.txt: standardize document format
...
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAllqXNUACgkQ8vlZVpUN
gaPtAgf/aUbXZuWYsDQzslHsbzEWi+qz4QgL885/w4L00pEImTTp91Q06SDxWhtB
KPvGnZHS3IofxBh2DC+6AwN6dPMoWDCfYhhO6po3FSz0DiPRIQCTuvOb8fhKY1X7
rTdDq2xtDxPGxJ25bMJtlrgzH2XlXPpVyPUeoc9uh87zUK5aesXpUn9kBniRexoz
ume+M/cDzPKkwNQpbLq8vzhNjoWMVv0FeW2akVvrjkkWko8nZLZ0R/kIyKQlRPdG
LZDXcz0oTHpDS6+ufEo292ZuWm2IGer2YtwHsKyCAsyEWsUqBz2yurtkSj3mAVyC
hHafyS+5WNaGdgBmg0zJxxwn5qxxLg==
=ua7p
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Add wait_for_random_bytes() and get_random_*_wait() functions so that
callers can more safely get random bytes if they can block until the
CRNG is initialized.
Also print a warning if get_random_*() is called before the CRNG is
initialized. By default, only one single-line warning will be printed
per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
warning will be printed for each function which tries to get random
bytes before the CRNG is initialized. This can get spammy for certain
architecture types, so it is not enabled by default"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
random: warn when kernel uses unseeded randomness
net/route: use get_random_int for random counter
net/neighbor: use get_random_u32 for 32-bit hash random
rhashtable: use get_random_u32 for hash_rnd
ceph: ensure RNG is seeded before using
iscsi: ensure RNG is seeded before use
cifs: use get_random_u32 for 32-bit lock random
random: add get_random_{bytes,u32,u64,int,long,once}_wait family
random: add wait_for_random_bytes() API
Pull ->s_options removal from Al Viro:
"Preparations for fsmount/fsopen stuff (coming next cycle). Everything
gets moved to explicit ->show_options(), killing ->s_options off +
some cosmetic bits around fs/namespace.c and friends. Basically, the
stuff needed to work with fsmount series with minimum of conflicts
with other work.
It's not strictly required for this merge window, but it would reduce
the PITA during the coming cycle, so it would be nice to have those
bits and pieces out of the way"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
isofs: Fix isofs_show_options()
VFS: Kill off s_options and helpers
orangefs: Implement show_options
9p: Implement show_options
isofs: Implement show_options
afs: Implement show_options
affs: Implement show_options
befs: Implement show_options
spufs: Implement show_options
bpf: Implement show_options
ramfs: Implement show_options
pstore: Implement show_options
omfs: Implement show_options
hugetlbfs: Implement show_options
VFS: Don't use save/replace_mount_options if not using generic_show_options
VFS: Provide empty name qstr
VFS: Make get_filesystem() return the affected filesystem
VFS: Clean up whitespace in fs/namespace.c and fs/super.c
Provide a function to create a NUL-terminated string from unterminated data
Simon Horman