When the kernel command line parameter, no_console_suspend, is used,
the console should continue to output console messages during and
after system suspend. For a serial console, the serial core ensures
that the device is not shutdown when no_console_suspend is specified.
However, the default operation of the pnp bus will disable and suspend
the device and no further output occurs.
When registering the 8250 port, if the serial device is a console
set the PNP_CONSOLE capability, which prevents device power-off
if consoles are not suspending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unregister_console() will be called from uart_remove_one_port() while
removing the platform driver. So not necessary to call it in driver
exit path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change does following:
- baud, flow, bits, parity were being overwritten as they were
being reinitialized after parsing. Initialize them when they are
declared so that user provided setting are not overwritten.
- msm_set_baud_rate() is anyway called in uart_set_options when it calls
msm_set_termios(). msm_reset() is called when we change the baud rate.
Hence doing away with both of these calls.
- CR_CMD_PROTECTION_EN and CR_TX_ENABLE settings are done in msm_set_baud_rate.
So do away with this here.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Moorestown platform support was removed few years ago. This is a follow
up which removes Moorestown specific code for the serial devices. It includes
mrst_max3110 and earlyprintk bits.
This was used on SFI (Medfield, Clovertrail) based platforms as well, though
new ones use normal serial interface for the console service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running an userspace program that does a 'tcflush(fd, TCIOFLUSH)' call
we still see the last received character in the URXD register afterwards.
Clear UCR2_SRST bit so that the UART FIFO is flushed properly.
Since UCR2_SRST also resets some UART registers, we need to save and restore
some of them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Acked-by: Jason Liu <r64343@freecale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On uart buffer flush, serial core resets the circular buffer.
If a DMA transfer is in progress at that time, the callback
lpuart_dma_tx_complete will move buffer's tail unconditionally,
hence tail moves beyond head. Use the flush_buffer hook to
terminate the DMA imeaditely and avoid lpuart_dma_tx_complete
being called in this situation.
This bug often showed up while shutdown and lead to duplicate
serial console output.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For power management support, we should disable TX and
TX interrupt so that kernel can prepare for deep sleep.
Retain RX and RX interrupt for wakeup the kernel when
receive the input character.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To end a DMA transfer which did not consume a whole buffer (e.g. one
character only), a RX timer is used. When lots of data are received
the DMA transfer will complete and setup another DMA transfer, which
in turn might complete again. In this cases, it is not necessary to
abort the DMA transfers using the RX timer. This change pushes the
RX timer timeout into the future each time a DMA transfer completed.
Aborting the DMA was not very harmful, since the next received
character lead to setup of another RX DMA.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the DMA channel request to probe to avoid requesting the DMA
channel on each opening of the ttyLPx device. This also fixes a
potential issue that TX channel is not freed when only RX channel
allocation fails. The DMA channels are now handled independently,
so one could use UART with DMA only in TX direction for instance.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In early 8250, IER is already zero so no point in writing this - twice
per line
This helped improve the SystemC model based ARC OSCI platform
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
-FCR[RTL] = 00 1 byte
-FCR[RTL] = 01 16 bytes
-FCR[RTL] = 10 32 bytes
-FCR[RTL] = 11 56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
workaround of errata A-008006 which states that tx_loadsz should
be configured less than Maximum supported fifo bytes
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When IGNPAR is set in termios->c_iflag, characters with
framing errors should be ignored.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNPAR/INPCK are clear in termios->c_iflag, characters
received with parity or framing errors should be preserved
and passed to the upper layers of the tty stack.
Specifically, the decision of whether to set the character
value to zero should be made by n_tty.c/n_tty_receive_parity_error().
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RX DMA transfers support for samsung serial driver. It's enabled
when DMA controller for RX channel is specified in device-tree.
DMA transactions are started when number of bytes in RX FIFO reaches
trigger level, otherwise PIO mode is used. DMA transfer size is always
PAGE_SIZE which can cause large latency when smaller data amount is
transferred, so we always terminate DMA transaction on RX timeout
interrupt. Timeout interval is set to 64 frame times.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add TX DMA transfers support for samsung serial driver. It's enabled
when "dmas" property is defined in serial device-tree node, otherwise
TX transfers are prerformed using PIO.
TX DMA is used for data segments larger than fifosize to reduce number
of interrupts during data transmission. For buffers shorter than fifosize
PIO mode is selected.
Data blocks for DMA transfers are aligned to cache line size to avoid
problems with coherency (some areas of TX circ buffer can be used by
CPU during DMA transaction, so we have to ensure that our data is always
consistent).
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functions requesting and releasing RX and TX DMA channels. This
function are called only when "dmas" property in serial device-tree
node is defined.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have "dmas" property in serial node in device-tree, we do
memory alocation for dma structure which will be used in DMA handling
code.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This struct contains DMA configuration for each serial port.
It will be used in next commits adding DMA support in driver.
Based on previous work of Sylwester Nawrocki and Lukasz Czerwinski.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds Software flow control support in DMA mode.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After send out x_char in UART driver, x_char needs to be cleared
by UART driver itself, otherwise data in TXFIFO can no longer be
sent out.
Also tx counter needs to be increased to keep track of correct
number of transmitted data.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other than enable Receiver Overrun Interrupt Enable (UCR4_OREN)
in start_tx interface, UCR4_OREN should be enabled before enable
of Receiver.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start rx_dma once RXFIFO is not empty that can avoid dma request lost
and causes data delay issue.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA mode for UART can be used even w/o HW flow control with RTS/CTS.
So it need to be initialized and enabled earlier.
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminating the DMA, make sure the interrupt is disabled, too.
This fixes random kernel Oops due to dma_tx_call() called for
invalid transmissions.
If we disable the TDMAEN, make sure it's enabled again if a TX
DMA is started.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in dma_tx_callback(), no matter if there is still
remaining data pending in circle buffer or not, DMA transmit
will be terminated.
This will result in some data never get transmitted.
In order to fix this issue, call imx_dma_tx() again in
dma_tx_callback, when there is pending data and uart hasn't
been stopped.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ad28e3efe.
Instead of always wake up write_wait process in TX callback,
TX callback should call imx_dma_tx() again, and let imx_dma_tx
transfer the remaining data in circle buffer.
The issue with commit 2ad28e3 is, in case there is remaining
data in circle buffer, but no process is waiting on write_wait
queue, then as no following uart_write() will be called after
uart_write_wakeup(), thus cause data loss.
Moreover according to Documentation/serial/driver, uart_write_wakeup()
should be called in case the transmit buffer have dropped below
a threshold.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To synchronize between dma_tx_callback() and imx_dma_tx() use the same
variable, dma_is_txing. This prevents any race between these two functions
and ensures that a new DMA can start only after the first has been
finished.
Before the new DMA can be set up, update the circular buffer logic, first.
Therefore, change dma_is_txing after that update, instead of before.
While doing this, in dma_tx_callback() extend the locking to dma_unmap_sg()
and the update of dma_is_txing.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, reformat the code to exit immediately. This allows us to add
more code in more readable format.
In case the TX DMA was still running, remove and disable it's resources.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case dmaengine_prep_slave_sg() fails, add the missing dma_unmap_sg().
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inverting the logic of the if statement for the sg initialization
makes the if statement easier and better to read.
No functional change.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use imx_start_tx() just to enable the TX interrupt. It's the job of the
TX interrupt ISR to fill the transmit buffer, then. If the transmit buffer
is empty, the TX interrupt should be executed as soon as the start_tx()
enables the interrupt, so there is no reason for the extra
imx_transmit_buffer() call, here. Remove it.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Lowe <andy_lowe@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several places are accessing the UCR1 register without locking.
This probably will cause a race issue when another thread
is accessing the same register.
Add locking to preventing concurrent access of the UCR1 register.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CREAD flag hanlding in set_termios and UART DMA mode
which ignores all received chars when CREAD flag cleared.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Anton Bondarenko <anton_bondarenko@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes many bugs in the code dealing with the hardware handshake.
As an example, in atmel_set_termios(), we used to test whether the CRTSCTS
c_cflag was set. If so, we selected the "Hardware Handshake" mode through the
Mode Register. However, few lines below the mode was reset to "Normal" (0).
So there was no way to select the "Hardware Handshake" mode. To fix this issue,
we moved the CRTSCRTS c_cflag test AFTER the mode has been reset to "Normal".
Also setting the RTSEN and RTSDIS bits in the Control Register has different
results whether the USART is set in "Normal" or "Hardware Handshake" mode:
1) "Normal" mode
- the RTSEN bit forces the RTS line to low level, which tells the remote peer
that we are ready to received new data.
- the RTSDIS bit forces the RTS line to high level, which tells the remote peer
to stop sending new data.
2) "Hardware Handshake" mode
- the RTSEN bit forces the RTS line to high level.
- the RTSDIS bit lets the hardware control the RTS line.
WARNING:
when FIFOs are not available or not enabled, the RTS line is controlled by the
PDC. This is why using the Hardware Handshake mode requires using the PDC
channel for reception. However the Hardware Handshake mode DOES NOT work with
DMA controller since it cannot control the RTS line.
Future designs with FIFOs will introduce a new feature: the RTS line will be
controlled by the RX FIFO using thresholds. This patch was tested with this new
design.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-EDEFER error wasn't handle properly by atmel_serial_probe().
As an example, when atmel_serial_probe() is called for the first time, we pass
the test_and_set_bit() test to check whether the port has already been
initalized. Then we call atmel_init_port(), which may return -EDEFER, possibly
returned before by clk_get(). Consequently atmel_serial_probe() used to return
this error code WITHOUT clearing the port bit in the "atmel_ports_in_use" mask.
When atmel_serial_probe() was called for the second time, it used to fail on
the test_and_set_bit() function then returning -EBUSY.
When atmel_serial_probe() fails, this patch make it clear the port bit in the
"atmel_ports_in_use" mask, if needed, before returning the error code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_serial_probe() calls atmel_init_port(). In turn, atmel_init_port() calls
clk_disable_unprepare() to disable the peripheral clock before returning.
Later atmel_serial_probe() accesses some I/O registers such as the Mode and
Control registers for RS485 support then the Name and Version registers, through a call to
atmel_get_ip_name(), but at that moment the peripheral clock was still
disabled.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MARCO will not be supported any more and the project was dropped.
it has been replaced by CSR atlas7.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable APM X-Gene SoC serial port functionality when using ACPI table to
initialize serial port.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to terminate transfer in the __dma_rx_complete() since it's
called at the end of transfer. Special case when serial timeout occurs is
handled separately where we have to terminate transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_request_irq() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_clk_get() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using devm_kzalloc() we can have a shorter and cleaner code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of jumping to the 'out' label, let's return the error immediately, which
makes the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the OMAP3 UART ignores MCR[1] (RTS) in autoRTS mode, autoRTS
mode must not be enabled unless RTS is set (or port->mctrl & TIOCM_RTS,
which is equivalent).
Fixes premature raising of RTS in omap_8250_set_termios() -- RTS was
raised even before UART mode was selected.
Fixes raise of RTS after port has been shutdown; omap_8250_pm() re-enabled
RTS after omap_8250_shutdown().
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fixes for omap-serial.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
index 18c30ca..f43ed2c 100644
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch invokes add_preferred_console() with ttyS based on ttyO
arguments if the user didn't specify it on its own. This ensures that
the user will see the kernel booting on his serial console in case he
forgot to update the command line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current output of the device probing looks like this:
ColdFire internal UART serial driver
(NULL device *): ttyS0 at MMIO 0xfc060000 (irq = 90, base_baud = 5208333) is a ColdFire UART
console [ttyS0] enabled
(NULL device *): ttyS1 at MMIO 0xfc064000 (irq = 91, base_baud = 5208333) is a ColdFire UART
(NULL device *): ttyS2 at MMIO 0xfc068000 (irq = 92, base_baud = 5208333) is a ColdFire UART
Fix the port device linkage at probing time so that the device name is
printed out properly, and not "(NULL device *)".
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivially fix the following compile time warnings:
CC drivers/tty/serial/mcf.o
drivers/tty/serial/mcf.c: In function ‘mcf_set_termios’:
drivers/tty/serial/mcf.c:201:19: warning: unused variable ‘pp’
drivers/tty/serial/mcf.c: In function ‘mcf_config_rs485’:
drivers/tty/serial/mcf.c:444:19: warning: unused variable ‘pp’
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change my email contact address from the obsolete gerg@snapgear.com to
gerg@uclinux.org.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WCH384 4S board is a PCI-E card with 4 DB9 COM ports detected as
Serial controller: Device 1c00:3470 (rev 10) (prog-if 05 [16850])
Signed-off-by: Sergej Pupykin <ml@sergej.pp.ru>
Acked-by: Zany Yan <sirlight@cox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This is a partial revert of 2f2dafe (serial: serial_core.c: printk
replacement) which gets us booting again. The real problem seems to be
the _emit path in early boot. However, until we can root cause it, we
need at least to get boot working.
Fixes: 2f2dafe77d
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_omap serial driver is a new user of CONFIG_PM_RUNTIME.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
#ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in 8250_omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Here's the big tty/serial driver update for 3.19-rc1.
There are a number of TTY core changes/fixes in here from Peter Hurley
that have all been teted in linux-next for a long time now. There are
also the normal serial driver updates as well, full details in the
changelog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD/MACgkQMUfUDdst+ymW+wCfbSzoYMRObIImMPWfoQtxkvvN
rpkAnAtyEP/zZIfkQIuKTSH6FJxocF8V
=WZt3
-----END PGP SIGNATURE-----
Merge tag 'tty-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver update for 3.19-rc1.
There are a number of TTY core changes/fixes in here from Peter Hurley
that have all been teted in linux-next for a long time now. There are
also the normal serial driver updates as well, full details in the
changelog below"
* tag 'tty-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (219 commits)
serial: pxa: hold port.lock when reporting modem line changes
tty-hvsi_lib: Deletion of an unnecessary check before the function call "tty_kref_put"
tty: Deletion of unnecessary checks before two function calls
n_tty: Fix read_buf race condition, increment read_head after pushing data
serial: of-serial: add PM suspend/resume support
Revert "serial: of-serial: add PM suspend/resume support"
Revert "serial: of-serial: fix up PM ops on no_console_suspend and port type"
serial: 8250: don't attempt a trylock if in sysrq
serial: core: Add big-endian iotype
serial: samsung: use port->fifosize instead of hardcoded values
serial: samsung: prefer to use fifosize from driver data
serial: samsung: fix style problems
serial: samsung: wait for transfer completion before clock disable
serial: icom: fix error return code
serial: tegra: clean up tty-flag assignments
serial: Fix io address assign flow with Fintek PCI-to-UART Product
serial: mxs-auart: fix tx_empty against shift register
serial: mxs-auart: fix gpio change detection on interrupt
serial: mxs-auart: Fix mxs_auart_set_ldisc()
serial: 8250_dw: Use 64-bit access for OCTEON.
...
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new
iommu DT binding. More drivers like this are likely to follow
for the following merge window, but we should be able to do
those through the iommu maintainer.
Other notable changes are:
* reset controller drivers from the reset maintainer (socfpga, sti, berlin)
* fixes for the keystone navigator driver merged last time
* at91 rtc driver changes related to the at91 cleanups
* ARM perf driver changes from Will Deacon
* updates for the brcmstb_gisb driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MwMG
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
Make the serial_mctrl_gpio driver the first user of the new gpiod_set_array
function, which is now available in the linux-gpio devel tree.
All modem control output signals are now set simultaneously.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds suspend/resume support for the of-serial driver
to provide power management support on devices attatched.
The handling may vary since not every of_serial device is
an 8250 port. Currently only 8250 port handling is added
in the suspend/resume function based on the type switch.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Joseph Lo <josephl@nvidia.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Florina Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2dea53bf57.
Turns out to be broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 513e438581.
It's broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Joseph Lo <josephl@nvidia.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attempting to use SysRq via the 8250 serial port with spin lock
debugging on on a uniprocessor system results in the following splat:
SysRq :
BUG: spinlock trylock failure on UP on CPU#0, swapper/0
lock: serial8250_ports+0x0/0x8c0, .magic: dead4ead, .owner: swapper/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper Not tainted 3.18.0-rc4+ #37
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
ffffffff8245ba00 ffffffff81628b28 ffffffff812c8d27 ffffffff81628b48
ffffffff8106812e ffffffff8245ba00 ffffffff814e22ed ffffffff81628b68
ffffffff810681a6 0000000000000000 0000000000000000 ffffffff81628b88
Call Trace:
<IRQ> [<ffffffff812c8d27>] dump_stack+0x19/0x1b
[<ffffffff8106812e>] spin_dump+0x7e/0xd0
[<ffffffff810681a6>] spin_bug+0x26/0x30
[<ffffffff8106843c>] do_raw_spin_trylock+0x4c/0x60
[<ffffffff812cdb1d>] _raw_spin_trylock+0x1d/0x60
[<ffffffff812336d8>] serial8250_console_write+0x68/0x190
[<ffffffff811eb0b0>] ? sprintf+0x40/0x50
[<ffffffff8106ab5e>] call_console_drivers.constprop.11+0x9e/0xf0
[<ffffffff8106b276>] console_unlock+0x3e6/0x490
[<ffffffff8106b595>] vprintk_emit+0x275/0x530
[<ffffffff812c869a>] printk+0x4d/0x4f
[<ffffffff8121e612>] __handle_sysrq+0x62/0x1b0
[<ffffffff8121e5b5>] ? __handle_sysrq+0x5/0x1b0
[<ffffffff8121ebc6>] handle_sysrq+0x26/0x30
[<ffffffff81233157>] serial8250_rx_chars+0x1d7/0x250
[<ffffffff812338bb>] serial8250_handle_irq+0x7b/0x90
[<ffffffff812338f3>] serial8250_default_handle_irq+0x23/0x30
[<ffffffff812318b3>] serial8250_interrupt+0x63/0xe0
[<ffffffff8106d80e>] handle_irq_event_percpu+0x4e/0x200
[<ffffffff8106da01>] handle_irq_event+0x41/0x70
[<ffffffff810701ee>] ? handle_edge_irq+0x1e/0x110
[<ffffffff8107026e>] handle_edge_irq+0x9e/0x110
[<ffffffff810041c2>] handle_irq+0x22/0x40
[<ffffffff812d096e>] do_IRQ+0x4e/0xf0
[<ffffffff812cf4ed>] common_interrupt+0x6d/0x6d
<EOI> [<ffffffff8100acbf>] ? default_idle+0x1f/0xd0
[<ffffffff8100acbd>] ? default_idle+0x1d/0xd0
[<ffffffff8100b61f>] arch_cpu_idle+0xf/0x20
[<ffffffff8105c1db>] cpu_startup_entry+0x25b/0x360
[<ffffffff812c726e>] rest_init+0xbe/0xd0
[<ffffffff816a4dcb>] start_kernel+0x339/0x346
[<ffffffff816a4495>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff816a4589>] x86_64_start_kernel+0xf2/0xf6
HELP : loglevel(0-9) reboot(b) crash(c) show-all-locks(d) te...
Before ebade5e833 ("serial: 8250: Clean up the locking for -rt")
this was handled by not even attempting to try the lock if port->sysrq,
since it is known to be taken by the interrupt handler; see
https://bugzilla.kernel.org/show_bug.cgi?id=6716#c1. Restore that
behavior.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since most drivers interpret UPIO_MEM32 to mean "little-endian" and use
readl/writel to access the registers, add a parallel UPIO_MEM32BE to
request the use of big-endian MMIO accessors (ioread32be/iowrite32be).
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardcoded FIFO size can cause hardware performance limitation.
Using real size value provides better FIFO usage.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have fifosize set in driver data we prefer to use it instead of default
fifosize value (which is always 16). If there is defined fifosize for particular
serial we prefer to use it, otherwise we use value from info, which is
common for all serials on given platform.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds waiting until transmit buffer and shifter will be empty
before clock disabling.
Without this fix it's possible to have clock disabled while data was
not transmited yet, which causes unproper state of TX line and problems
in following data transfers.
Cc: <stable@vger.kernel.org> # v2.6.26+
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty break and error flags are not bit masks so do not to use bitwise
OR when assigning them.
Note that there is no functional change due to the if-else construct and
flag having been initialised to zero (TTY_NORMAL).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original driver fixed the io address with 0xe000+idx*8,
but real io address assigned from BIOS is dynamically from
read PCI configure space 0x24, 0x20, 0x1c.
The Fintek F81504/F81508/F81512 maybe malfunction without
this patch and malfunction surely when more then 1 PCI card.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tx_empty() should test whether both the transmitter fifo and shifter
for the port is empty, ie. the whole last char was transmitted.
The shift register is empty if AUART_STAT_BUSY is cleared.
The patch fixes the function against the shift register.
According to i.MX23 and i.MX28 Reference Manual:
AUART_STAT_TXFE:
TX FIFO or transmit holding register is empty.
AUART_STAT_BUSY:
AUART still transmits bits.
The BUSY signal goes HIGH as soon as the data is written to the
transmit FIFO (that is, the FIFO is non-empty) and remains asserted
HIGH while data is being transmitted.
BUSY is negated only when the transmit FIFO is empty, and the last
character has been transmitted from the shift register, including
the stop bits.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxs_auart_modem_status() did't detect gpio's state change
because s->mctrl_prev was modified before by mctrl_gpio_get().
The patch introduces mctrl_temp variable to fix the bug.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 732a84a037 ("serial: core: Pass termios to set_ldisc() notifications")
changed the set_ldisc prototype.
At the time of this commit the mxs_auart driver did not implement set_ldisc,
so that's why it has not been converted.
Adapt also mxs_auart_set_ldisc() so that the following build warning can be
fixed:
drivers/tty/serial/mxs-auart.c:962:2: warning: initialization from
incompatible pointer type
.set_ldisc = mxs_auart_set_ldisc,
^
drivers/tty/serial/mxs-auart.c:962:2: warning: (near initialization
for 'mxs_auart_ops.set_ldisc')
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable. Also the OCTEON simulation environments
prohibit 8-bit accesses.
For these reasons, we use __raw_readq/__raw_writeq for OCTEON. This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.
We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_SERIAL_IMX_CONSOLE=n and CONFIG_CONSOLE_POLL=y we get the following
build warning:
drivers/tty/serial/imx.c:306:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:315:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
imx_port_ucrs_save/restore are only used under CONFIG_SERIAL_IMX_CONSOLE, so
their definitions should be also be protected only by CONFIG_SERIAL_IMX_CONSOLE.
This was detected when building 'allmodconfig'.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
Since of_alias_get_id() and pdev->id can get negative I check for the
error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter reported:
|drivers/tty/serial/8250/8250_omap.c:1025 omap8250_probe()
|warn: unsigned 'up.port.line' is never less than zero.
|1025 if (up.port.line < 0) {
I (wrongly) assumed that line is an int and compiler didn't complain nor
did sparse. Since of_alias_get_id() and pdev->id can get negative I
check for the error via ret variable.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mcb_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in CSR A7DA SoC, uart6 located at BT module and it need multiple clock
sources, so for "sirf,marco-bt-uart" compatible uarts, drivers take 3
clock sources and enable them.
this patch also replaces clk_get by devm_clk_get function and fix DT
binding document in which we missed to fix when we added marco platform
in commit 909102db44 "serial: sirf: add support for Marco chip".
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the pr_warning to the more common pr_warn.
Other miscellanea:
o Convert unusual PR_FMT define and uses to pr_fmt
o Remove unnecessary OOM message
o Fix grammar in an error message
o Convert a pr_warning with a KERN_ERR to pr_err
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit deals with the checkpatch warning "Unnecessary space before
function pointer arguments".
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The changed function flushes the tx UART and the '4' corresponds to the
UART_FCR_CLEAR_XMIT value. This commit replaces the magic number with
this define.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the alignment of the 'case's i the switch statement.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flow of {neo,cls}_param() shows that at this stage the baud rate
has a non-zero value. This fact makes the if clausule obsolete and
acknowledges it's removal.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'force' parameter to the {cls,neo}_send_break() function has been
removed because it has not been used. The client to this API (the tty
code) always called this function with only one value.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes negative values of error rate to be checked, because these
values are valid as error rate. And this changes in the process of adopting
a value close to 0.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2dea53bf57.
Turns out to be broken :(
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there isn't a DT alias then of_alias_get_id() will return
-ENODEV. This will cause the msm_serial driver to fail probe,
when we want to keep the previous behavior where we generated a
dynamic line number at probe time. Restore this behavior by
generating a dynamic id if the line number is still negative
after checking for an alias or in the non-DT case looking at the
.id field of the platform device.
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exynos7 has a similar serial controller to that present in older Samsung
SoCs. To re-use the existing serial driver on Exynos7 we need to have
SERIAL_SAMSUNG_UARTS_4 and SERIAL_SAMSUNG_UARTS selected. This is not
possible because these symbols are dependent on PLAT_SAMSUNG which is
not present for the ARMv8 based exynos7.
Change the dependency of these symbols from PLAT_SAMSUNG to the serial
driver thus making it available on exynos7. As the existing platform
specific code making use of these symbols is related to uart driver this
change in dependency should not cause any issues.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fix spelling typo in printk and Kconfig within
various part of kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 1bd8324535.
To quote Olof:
This commit broke a whole lot of tegra boards in last night's
-next here. In particular, I've been looking at
tegra20-seaboard, which now doesn't boot with console any more.
Breaking existing systems is bad.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add equivalent attributes to those provided in the platform data
for use when RX DMA is enabled.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the DMA engine doesn't support residue processing then the RX DMA
handling won't work terribly well if polling is enabled. So, disable
RX DMA if residue handling isn't available.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA engines on some systems require that the dma_length is set
when using scatter gather lists.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing code assumed that PL011_DMA_BUFFER_SIZE == UART_XMIT_SIZE,
which may not always be the case. This allows for these two being
different sizes and not copying too much data.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating with __GFP_DMA avoids the need for bounce buffers
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no real value in displaying "serial: Freescale lpuart driver" in every
boot.
The uart_register_driver() can fail and even so the "serial: Freescale lpuart
driver" will be displayed, which is not really helpful.
This is particularly annoying when booting multi_v7_defconfig kernel on a SoC
that is not a Vybrid/Layerscape and even though this message gets displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'res' will be automatically checked inside devm_ioremap_resource(), so there is
no need to explicitly perform a NULL check.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit removes the address of Free Software Foundation from each
of the mentioned file in order to suppress the checkpatch warning.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit enables support for the Digi Classic adapters line in the
jsm driver. This means changes in:
- device probing code
- device cleanup code
- driver description (Kconfig)
The init/cleanup code is based on the staging/dgnc driver.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds the Digi Classic board implementation to the
staging/jsm driver.
The code here is taken from the staging/dgnc driver and modified to
match the serial/jsm state. This work is mostly based on the changes
that has been done to the code handling the Digi Neo cards with the
inspiration coming from the diff between staging/dgnc and serial/jsm
as well as the LKML history for the jsm_neo.c
The code compiles now and has no sparse and checkpatch errors or
warnings.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In serial8250_rx_chars(), max_count is set to 256. Due to the
post-decrement operator used in the while() condition, the maximum
number of iterations actually 257. This is not a problem, but it is
mildly surprising if you're debugging. Use pre-decrement instead.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds the UART structure for the Digi Classic cards. This
code comes from the staging/dgnc driver.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
port->membase was allocated using devm_ioremap_nocache, so ideally
we should unmap it using devm_iounmap. but it was using iounmap.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the serial8250_tx_dma() the tx_err flag is set in case of error. Thus, there
is no need to repeat this in __dma_tx_complete().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have the same check inside the function we may drop it away in
__dma_tx_complete().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an homogeneous lock system between setting and using the rs485
data of the uart_port.
This patch should not be split into multiple ones in order to avoid
leaving the tree in an unstable state.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Suggested-by: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once there is no more handlers for TIOC[GS]RS485 there is no need to
call the driver specific ioctl when the generic implementation is
missing.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling.
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling.
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling.
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no more users for this functions. All the 8250 drivers are
using the rs485 handler on serial_core instead.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to remove the handler for rs485 ioctls on serial_8250, all the
drivers must use the implementation on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following drivers: 8250_core, atmel_serial, max310x, mcf, omap-serial
and sci16is7xx implement code to handle RS485 ioctls.
In order to avoid code duplication, we implement a simple ioctl handler
on the serial_core layer.
This handler can be used by all the other drivers instead of duplicating
code.
Until this is the only RS485 ioctl handler, it will try first the
rs485_config callback and if it is not present it will call the driver
specific ioctl.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed a sparse warning in 8250_core.c :
incorrect type in assignment (different address spaces)
the warning was because an unsigned char pointer was being assigned to
a pointer of unsigned char __iomem type .
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WCH382 is a PCI-E card with 1 LPT and 2 DB9 COM ports detected as
Serial controller: Device 1c00:3250 (rev 10) (prog-if 05 [16850])
Signed-off-by: Sergej Pupykin <ml@sergej.pp.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switching to the N_PPS line discipline may require enabling
modem status interrupts; conversely switching from N_PPS may
require disabling modem status interrupts.
Affected drivers:
8250
amba-pl010
atmel
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three UART drivers (8250, atmel & amba-pl010) directly call their
enable_ms() method; the uart port lock must be acquired before
any h/w programming.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART drivers which enable modem status interrupts when switching
to N_PPS line discipline need to determine if modem status
interrupts should be disabled when switching from N_PPS.
Specifically, the set_ldisc() notification needs to evaluate
UART_ENABLE_MS() which requires termios->c_cflag.
Convert in-tree UART drivers to new interface.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three UART drivers (8250, atmel & amba-pl010) enable modem status
interrupts if the line discipline is changed to N_PPS. However,
the uart port flags may only be safely modified while holding the
port mutex.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for setting the state of the DTR and RTS signals.
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get index of serial line from device tree using function of_alias_get_id().
If no alias is found, the 8250 core takes care of incrementing the line number.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The general agreed way to specify a fixed line number
for a serial console is to provide a "serial" alias
in the devicetree. Start parsing this property in
of_serial.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the return value of ioremap_nocache to make sure we got a
valid mapping.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds 32-bit register lpuart32 power management support,
this also updates the 8-bit register lpuart resume function.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are removing the dmaengine_device_control API, that shouldn't even have been
exposed in the first place. Change the callers to use the proper API.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mtk8250_set_termios function, calculating quot value can not be zero,
otherwise, using DIV_ROUND_CLOSEST(port->uartclk, quot * baud) will fail due to
divisor is zero.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't really need to perform the ioremap "on demand" so it's simpler
just to do it from the probe function. This also lets us eliminate the
UART_REG_SIZE constant and rely on the resource information passed in
from the DT or platform code.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables early console output if there is a chosen/stdout-path
property referencing a UART node with the "brcm,bcm6345-uart" compatible
string. The bootloader sets up the pinmux and baud/parity/etc.
Tested on bcm3384 (MIPS, DT).
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove incorrect "bcm963xx_uart" module name; add a list of known users;
tweak grammar/indentation/capitalization.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original non-DT bcm63xx clk code ignores the struct device argument
and looks up a global clock name. DT platforms, by contrast, often just
use a phandle to reference a clock node with no "clock-output-names"
property. Modify the UART driver to support both schemes.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device was originally supported on bcm63xx only, but it shows up on
a wide variety of MIPS and ARM chipsets spanning multiple product lines.
Now that the driver has eliminated dependencies on bcm63xx-specific
header files, we can build it on any non-bcm63xx kernel.
Compile-tested on x86, both statically and as a module. Tested for
functionality on bcm3384 (a new MIPS platform under active development).
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the console poll usage, .poll_init() will perform deeper hardware
initialization to ensure the serial port is always active.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Huang Shijie <b32955@freescale.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_put_poll_char() has been simplified to remove the code to disable
interrupts. The present code can corrupt register state when re-entered
from FIQ handler.
Switch to _relaxed() MMIO functions (which are safe for polled I/O and
needed to avoid taking spin locks).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Huang Shijie <b32955@freescale.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We rely on probe order of this driver to determine the line number for
the uart port. This makes it impossible to know the line number
when these devices are populated via DT. Use the DT alias
mechanism to assign the line based on the aliases node.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to issue a reset if we ever change the value of the IPR
register on DM hardware. If we don't reset the hardware the RX
stale interrupt never triggers and the only way to trigger an RX
handling event is by filling up the fifo. This causes things like
getty to not work so well considering it might change the baud
rate a few times. Fix this by moving the reset on startup and any
reprogramming required after the reset to be after we change the
baud rate.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly support sysrq on uartDM hardware we need to properly
handle break characters. With the DM hardware the fifo can pack 4
characters at a time, where a break is indicated by an all zero
byte. Unfortunately, we can't differentiate between an all zero
byte for a break and an all zero byte of data, so try and do as
best we can. First unmask the RX break start interrupt and record
the interrupt when it arrives. Then while processing the fifo,
detect the break by searching for an all zero character as long
as we recently received an RX break start interrupt. This should
make sysrq work fairly well.
Cc: Frank Rowand <frank.rowand@sonymobile.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enables PPS support in mxs-auart serial driver to make PPS API working.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dedicated CTS and RTS pins are unusable together with a lot of other
peripherals because they share the same line. Pinctrl is limited.
Moreover, the AUART controller doesn't handle DTR/DSR/DCD/RI signals,
so we have to control them via GPIO.
This patch permits to use GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI
signals.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King:
The only thing which the .get_mctrl method is supposed to do is
to return the state of the /input/ lines, which are CTS, DCD, DSR, RI.
The output line state is stored in port->mctrl, and is added to
the returned value by serial_core when it's required.
RTS output state should not be returned from the .get_mctrl method.
This patch removes ctrl variable from mxs_auart_port
and removes useless reading back RTS line.
The ctrl variable in mxs_auart_port duplicated mctrl,
member of uart_port structure in serial_core.h.
The removed code from mxs_auart_set_mctrl() and mxs_auart_get_mctrl
duplicated uart_update_mctrl() and uart_tiocmget()
in serial_core.c.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch swaps the use "tail" and "head" to fit the semantic of the linux
circular buffer documentation:
- head: the point at which the producer (the DMA controller) inserts items.
- tail: the point at which the consumer (the serial framework) finds the next
item.
Besides the former code of the rx ring buffer didn't manage the case where
head < tail, which might lead to loss of data. To fix this bug the data are now
sent from the DMA buffer to the serial framework in two steps:
1 - First, we test if head < tail. If so, we copy the data from tail to the end
of the DMA buffer then reset tail to zero.
2 - Finally, we copy data from tail to head then set tail to head.
In addition, since tty_insert_flip_string() may now be called twice,
atmel_flip_buffer_rx_dma() becomes less efficient than moving the calls
dma_sync_sg_for_cpu(), dma_sync_sg_for_device(), tty_insert_flip_string() and
tty_flip_buffer_push() directly into atmel_rx_from_dma().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the config symbol for Mediatek MT7620 SoC to the SERIAL_8250_RT288X
dependencies.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Ralink RT2880 SoC and its successors have an internal 8250 core. This core
needs the same quirks applied as the AMD AU1xxx uart. In addition to these
quirks, the ports memory region is only 0x100 unlike the AU1xxx which has a
size of 0x1000.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 479e9b94fd ("serial: Refactor uart_flush_buffer() from
uart_close") refactored the uart_flush_buffer() in uart_close() into
those drivers that define a flush_buffer() method. However, in the
amba-pl011 driver configured without CONFIG_DMA_ENGINE, flush_buffer()
is a NULL method, so the direct call fails to compile.
Check and call the flush_buffer() method through the ops table instead.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASYNC_SPLIT_TERMIOS behavior is a remnant of the long-dead /dev/cuaXX
callout device. Split termios handling was removed tree-wide in v2.5.71 by:
commit 99a21edebbfd8c29e39ee7fcc8a1ffa423657290
Author: Alexander Viro <viro@www.linux.org.uk>
Date: Wed Jun 11 07:41:28 2003 -0700
[PATCH] tty_driver refcounting
killed the last remnants of callout stuff - we don't need to mess with
storing termios privately anymore.
which pre-dated the re-introduction into the cris serial driver
in v2.6.7 by:
commit 311a5ffeda8ccb3f1f3840069f37234e043092d4
Author: Andrew Morton <akpm@osdl.org>
Date: Mon May 31 18:52:29 2004 -0700
[PATCH] CRIS architecture update
From: "Mikael Starvik" <mikael.starvik@axis.com>
- Lots of fixes from 2.4.
- Updated for 2.6.6.
- Added IDE driver
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
setup_serial_console() is obsolete and has been superseded by
early_serial_setup() which is called at the end of the function.
The IA64 arch does not call this function; only the m68k arch setup
calls this function.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The info pointer points to an uninitialized kmalloced space.
If a device doesn't have clk property, then info->clk may
have unpredicated value and cause call trace. So use kzalloc
to make sure it is NULL initialized.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of value quot for highspeed register set to three
was wrong. This patch fixes the calculation so that the serial port
for baudrates bigger then 576000 baud is working correctly.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no real value in displaying "Serial: IMX driver" in every boot.
The uart_register_driver() can fail and even so the "Serial: IMX driver" will
be displayed, which is not really helpful.
This is particularly annoying when booting multi_v7_defconfig kernel on a SoC
that is not a i.MX and even though this message gets displayed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kzalloc() fails the core MM will already complain about it, so there is
no need to have the error message locally.
Remove the unneeded error message.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of jumping to 'error_out1' label we can simplify the code and return the
error code directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a imx system with ttymxc0, ttymxc1 and ttymxc4 registered we see the
following output from 'cat /proc/interrupts':
$ cat /proc/interrupts
CPU0
...
58: 39 GIC 58 2020000.serial
67: 115 GIC 67 21f8000.i2c
The only uart irq that appears is ttymxc0, which is the console.
As ttymxc1 and ttymxc4 will only have their irq registered at imx_startup(),
they are not shown right after probe.
Transmitting to ttymxc1 and ttymxc4 will cause their irqs to be registered, but
the output shows:
$ echo "111111" > /dev/ttymxc1
$ echo "444444" > /dev/ttymxc4
$ cat /proc/interrupts
CPU0
...
58: 150 GIC 58 2020000.serial
59: 1 GIC 59
62: 1 GIC 62
67: 115 GIC 67 21f8000.i2c
,which misses printing the associated device address.
In order to fix this, register all the irqs inside the probe function via
devm_request_irq(), which will correctly report the serial interrupts associated
with their correspondent serial device and also helps simplyfing the code by
avoiding the calls to free_irq().
$ echo "111111" > /dev/ttymxc1
$ echo "444444" > /dev/ttymxc4
$ cat /proc/interrupts
CPU0
....
58: 202 GIC 58 2020000.serial
59: 1 GIC 59 21e8000.serial
62: 1 GIC 62 21f4000.serial
67: 115 GIC 67 21f8000.i2c
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the case in which we just provide an address as an argument to the
earlycon console type like:
earlycon=msm_serial_dm,0xf991e000
We would report this as an IO port based mapping and not as MMIO. Simple
fix to use the port->iotype to decide which message to print.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Mark RUtland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in drivers/tty/tty_io.c that were done in there for
future patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e676253b19 ("serial/8250: Add support for RS485 IOCTLs") added
references to TIOC[SG]RS48 on 8250_core.c. This change triggered the
need to define them in all the arches that uses tty/serial.
This made #ifdef TIOC[SG]RS48 obsolete.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e676253b19 ("serial/8250: Add support for RS485 IOCTLs") added
references to TIOC[SG]RS48 on 8250_core.c. This change triggered the
need to define them in all the arches that uses tty/serial.
This made #ifdef TIOC[SG]RS48 obsolete.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma pointer under struct uart_8250_port is currently left
unassigned for non-ACPI platforms. It should be pointing to the dma
member in struct dw8250_data like how it was done for ACPI, so the core
8250 code will try to request for DMA when registering the port
If DMA is not enabled in device tree, request DMA will fail and the
driver will fall back to PIO
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allows to read the REV_ID register in SPI mode and consequently
to properly detect the max3109. Indeed in SPI mode, this register is only
accessible by using indirect addressing.
Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 32726d2d55 ("ARM: SAMSUNG: Remove legacy clock code") removed
the Kconfig symbol SAMSUNG_CLOCK. Remove the last checks for its macro,
and the dead code they hide, too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the required pieces to 8250-OMAP UART driver for DMA
support. The TX burst size is set to 1 so we can send an arbitrary
amount of bytes.
The RX burst is currently set to 48 which means we receive an DMA
interrupt every 48 bytes and have to reprogram everything. Less bytes in
the RX-FIFO mean that no DMA transfer will happen and the UART will send a
RX-timeout _or_ RDI event at which point the FIFO will be manually purged.
There is a workaround for TX-DMA on AM33xx where we put the first byte
into the FIFO to kick start the DMA process. Haven't seen this problem on
OMAP36xx (beagle board xm) or DRA7xx.
On AM375x there is "Usage Note 2.7: UART: Cannot Acknowledge Idle
Requests in Smartidle Mode When Configured for DMA Operations" in the
errata document. This problem persists even after disabling DMA in the
UART and will be addressed in the HWMOD.
v10:
- delay update_registers() from set_termios() until TX-DMA is
done. It has been reported / proved that invoking
update_registers() while TX-DMA is in progress may stall the
DMA operation and it won't finish.
- use the new omap DMA-TX-RX hooks and DMA only interrupt
routine.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have (or will have) custom DMA callbacks in the omap driver due to
the different behaviour in the RX and TX case. To make this work
we need a few changes in the IRQ handler to invoke the rx_handler again
after the "manual" mode or retry the tx_handler again before falling
back to the manual mode.
Heikki didn't want to see the extra hacks in the generic / default irq
handler and Peter wasn't too happy about an OMAP-only IRQ handler. The
way I planned it is to use this extra IRQ routine only in DMA case. If
Peter dislike this approach then I hope Heikki doesn't block changes in
the default IRQ handler :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The omap needs a DMA request pending right away. If it is
enqueued once the bytes are in the FIFO then nothing will happen
and the FIFO will be later purged via RX-timeout interrupt.
This patch enqueues RX-DMA request on completion but not if it
was aborted on error. The first enqueue will happen in the driver
in startup.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides mostly a copy of serial8250_tx_dma() +
__dma_tx_complete() with the following extensions:
- DMA bug
At least on AM335x the following problem exists: Even if the TX FIFO is
empty and a TX transfer is programmed (and started) the UART does not
trigger the DMA transfer.
After $TRESHOLD number of bytes have been written to the FIFO manually the
UART reevaluates the whole situation and decides that now there is enough
room in the FIFO and so the transfer begins.
This problem has not been seen on DRA7 or beagle board xm (OMAP3). I am not
sure if this is UART-IP core specific or DMA engine.
The workaround is to use a threshold of one byte, program the DMA
transfer minus one byte and then to put the first byte into the FIFO to
kick start the transfer.
- support for runtime PM
RPM is enabled on start_tx(). We can't disable RPM on DMA complete callback
because there is still data in the FIFO which is being sent. We have to wait
until the FIFO is empty before we disable it.
For this to happen we fake a TX sent error and enable THRI. Once the
FIFO is empty we receive an interrupt and since the TTY-buffer is still
empty we "put RPM" via __stop_tx(). Should it been filed then in the
start_tx() path we should program the DMA transfer and remove the error
flag and the THRI bit.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP has a few corner cases where it needs a share of kindness of
affection to do the right thing. Heikki Krogerus suggested that instead
adding the quirks into the default DMA implementation, OMAP could get
its own copy of the function. And Alan suggested the same thing so here
we go.
This patch provides callbacks for custom TX/RX DMA implementation. If
there are not setup / used, then the default (current) implementation is
used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After dmaengine_terminate_all() has been invoked then both DMA drivers
(edma and omap-dma) do not invoke dma_cookie_complete() to mark the
transfer as complete. This dma_cookie_complete() is performed by the
Synopsys DesignWare driver which is probably the only one that is used
by omap8250-dma and hence don't see following problem…
…which is that once a RX transfer has been terminated then following
query of channel status reports DMA_IN_PROGRESS (again: the actual
transfer has been canceled, there is nothing going on anymore).
This means that serial8250_rx_dma() never enqueues another DMA transfer
because it (wrongly) assumes that there is a transer already pending.
Vinod Koul refuses to accept a patch which adds this
dma_cookie_complete() to both drivers and so dmaengine_tx_status() would
report DMA_COMPLETE instead (and behave like the Synopsys DesignWare
driver already does). He argues that I am not allowed to use the cookie
to query the status and that the driver already cleaned everything up after
the invokation of dmaengine_terminate_all().
To end this I add a bookkeeping whether or not a RX-transfer has been
started to the 8250-dma code. It has already been done for the TX side.
*Now* we learn about the RX status based on our bookkeeping and don't
need dmaengine_tx_status() for this anymore.
Cc: vinod.koul@intel.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now it is possible that serial8250_tx_dma() fails and returns
-EBUSY. The caller (serial8250_start_tx()) will then enable
UART_IER_THRI which will generate an interrupt once the TX FIFO is
empty.
In serial8250_handle_irq() nothing will happen because up->dma is set
and so serial8250_tx_chars() won't be invoked. We end up with plenty of
interrupts and some "too much work for irq" output.
This patch introduces dma_tx_err in struct uart_8250_port to signal that
the last invocation of serial8250_tx_dma() failed so we can fill the TX
FIFO manually. Should the next invocation of serial8250_start_tx()
succeed then the dma_tx_err flag along with the THRI bit is removed and
DMA only usage may continue.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides a 8250-core based UART driver for the internal OMAP
UART. The long term goal is to provide the same functionality as the
current OMAP uart driver and DMA support.
I tried to merge omap-serial code together with the 8250-core code.
There should should be hardly a noticable difference. The trigger levels
are different compared to omap-serial:
- omap serial
TX: Interrupt comes after TX FIFO has room for 16 bytes.
TX of 4096 bytes in one go results in 256 interrupts
RX: Interrupt comes after there is on byte in the FIFO.
RX of 4096 bytes results in 4096 interrupts.
- this driver
TX: Interrupt comes once the TX FIFO is empty.
TX of 4096 bytes results in 65 interrupts. That means there will
be gaps on the line while the driver reloads the FIFO.
RX: Interrupt comes once there are 48 bytes in the FIFO or less over
"longer" time frame. We have
1 / 11520 * 10^3 * 16 => 1.38… ms
1.38ms to react and purge the FIFO on 115200,8N1. Since the other
driver fired after each byte it had ~5.47ms time to react. This
_may_ cause problems if one relies on no missing bytes and has no
flow control. On the other hand we get only 85 interrupts for the
same amount of data.
It has been only tested as console UART on am335x-evm, dra7-evm and
beagle bone. I also did some longer raw-transfers to meassure the load.
The device name is ttyS based instead of ttyO. If a ttyO based node name
is required please ask udev for it. If both driver are activated (this
and omap-serial) then this serial driver will take control over the
device due to the link order
v9…v10:
- Tony noticed that omap3 won't show anything after waking up
from core off. In v9 I reworked the register restore and set
IER to 0 by accident. This went unnoticed because start_tx
usually sets ier (either due to DMA bug or due to TX-complete
IRQ).
- dropped EFR and SLEEP from capabilities. We do have both but
nobody should touch it. We already handle SLEEP ourself.
- make the private copy of the registers (like EFR) u8 instead
u32
- drop MDR1 & DL[ML] reset in restore registers. Does not look
required it is set to the required value later.
- update MDR1 & SCR only if changed.
- set MDR1 as the last thing. The errata says that we should
setup everything before MDR1 set.
- avoid div by 0 in omap_8250_get_divisor() if baud rate gets
very large (Frans Klaver fixed the same thing omap-serial)
- drop "is in early stage" from Kconfig.
v8…v9:
- less on a file seems to hang the am335x after a while. I
believe I introduce this bug a while ago since I can reproduce
this prior to v8. Fixed by redoing the omap8250_restore_regs()
v7…v8:
- redo the register write. There is now one function for that
which is used from set_termios() and runtime-resume.
- drop PORT_OMAP_16750 and move the setup to the omap file. We
have our own set termios function anyway (Heikki Krogerus)
- use MEM instead of MEM32. TRM of AM/DM37x says that 32bit
access on THR might result in data abort. We only need 32bit
access in the errata function which is before we use 8250's
read function so it doesn't matter.
v4…v7:
- change trigger levels after some tests with raw transfers.
v3…v4:
- drop RS485 support
- wire up ->throttle / ->unthrottle
v2…v3:
- wire up startup & shutdown for wakeup-irq handling.
- RS485 handling (well the core does).
v1…v2:
- added runtime PM. Could somebody could please double check
this?
- added omap_8250_set_termios()
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if I boot with console=ttyS0 and the omap driver is module I end up with
| console [ttyS0] disabled
| omap8250 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a 8250
| Unable to handle kernel paging request at virtual address c07a9de0
| Modules linked in: 8250_omap(+)
| CPU: 0 PID: 908 Comm: modprobe Not tainted 3.17.0-rc5+ #1593
| PC is at serial8250_console_setup+0x0/0xc8
| LR is at register_console+0x13c/0x3a4
| [<c0078788>] (register_console) from [<c02d0340>] (uart_add_one_port+0x3cc/0x420)
| [<c02d0340>] (uart_add_one_port) from [<c02d38a4>] (serial8250_register_8250_port+0x298/0x39c)
| [<c02d38a4>] (serial8250_register_8250_port) from [<bf006274>] (omap8250_probe+0x218/0x3dc [8250_omap])
| [<bf006274>] (omap8250_probe [8250_omap]) from [<c02e3424>] (platform_drv_probe+0x2c/0x5c)
| [<c02e3424>] (platform_drv_probe) from [<c02e1eac>] (driver_probe_device+0x104/0x228)
…
| [<c009fa48>] (SyS_init_module) from [<c000e6e0>] (ret_fast_syscall+0x0/0x30)
| Code: 7823603b f8314620 051b3013 491ed416 (44792204)
because serial8250_console_setup() is already gone.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Frans reworded the two comments with better English for better
understanding. His review hit the mailing list after the patch got
applied so here is an incremental update.
Reported-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using mxs-auart based console, sometime we need the sysrq function
to help debugging kernel. The sysrq code is basically there,
this patch just simply enable it.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This error message is not necessary. The driver core code will print all
probe error messages. It also resolves some error codes to proper error
messages. For example -EPROBE_DEFER will only be printed as an info message.
This patch removes the error message as the core prints the same
information.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A port count mismatch occurs if mutex_lock_interruptible()
exits uart_open() and the port has already been opened. This may
prematurely close a port on an open tty. Since uart_close() is _always_
called if uart_open() fails, the port count must be corrected if errors
occur.
Always increment the port count in uart_open(), regardless of errors;
always decrement the port count in uart_close(). Note that
tty_port_close_start() decrements the port count when uart_open()
was successful.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_start() only claims the port->lock to call __uart_start(),
which does the actual processing. Eliminate the extra acquire/release
in uart_write(); call __uart_start() directly with port->lock already
held.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The key function of uart_add_one_port() is to cross-reference the
UART driver's port structure with the serial core's state table;
keep the assignments together and document this crucial association.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_init() initializes close_delay and closing_wait to these
same values; remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wrapped line looks wrong and out-of-place; leave it as
>80 char line.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low-level uart driver may modify termios settings to override
settings that are not compatible with the uart, such as CRTSCTS.
Thus, callers of the low-level uart driver's set_termios() method must
hold termios_rwsem write lock to prevent concurrent access to termios,
in case such override occurs.
The termios_rwsem lock requirement does not extend to console setup
(ie., uart_set_options), as console setup cannot race with tty
operations. Nor does this lock requirement extend to functions which
cannot be concurrent with tty ioctls (ie., uart_port_startup() and
uart_resume_port()).
Further, always claim the port mutex to protect hardware
re-reprogramming in the set_termios() uart driver method. Note this
is unnecessary for console initialization in uart_set_options()
which cannot be concurrent with other uart operations.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty buffers (and any line discipline buffers) must be flushed after
the UART hardware has shutdown; otherwise, a racing open on the same
tty may receive data from the previous session, which is a security
hazard. However, holding the port mutex while flushing the line
discipline buffers creates a lock inversion if the set_termios()
handler takes the port mutex (as it does in the followup patch,
'serial: Fix locking for uart driver set_termios method'.
Flush the ldisc buffers after dropping the port mutex; the tty lock
is still held which prevents a concurrent open() from advancing while
flushing. Since no new rx data is possible after uart_shutdown() until
a new open reinitializes the port, the later flush has no impact on
what data is being discarded.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the context of the final tty & port close, flushing the tx
ring buffer after the hardware has already been shutdown and
the ring buffer freed is neither required nor desirable.
uart_flush_buffer() performs 3 operations:
1. Resets tx ring buffer indices, but the tx ring buffer has
already been freed and the indices are reset if the port is
re-opened.
2. Calls uart driver's flush_buffer() method
5 in-tree uart drivers define flush_buffer() methods:
amba-pl011, atmel-serial, imx, serial-tegra, timbuart
These have been refactored into the shutdown() method, if
required.
3. Kicks the ldisc for more writing, but this is undesirable.
The file handle is being released; any waiting writer will
will be kicked out by tty_release() with a warning. Further,
the N_TTY ldisc may generate SIGIO for a file handle which
is no longer valid.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added recognition of EndRun Technologies PCIe PTP slave card
and setup two ttySx ports for communication with the card for
retrieval of PTP based time and to communicate with the card's
Linux OS.
Signed-off-by: Mike Skoog <mskoog@endruntechnologies.com>
Signed-off-by: Mike Korreng <mkorreng@endruntechnologies.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ST16650V2 based serial uarts, while initalizing the PM state,
LCR registers are being initialized to 0 in serial8250_set_sleep().
If console port is already initialized and being used, this will
throws garbage in the console.
Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes commit 2dea53bf57,
"serial: of-serial: add PM suspend/resume support", which disables
the uart clock on suspend, but also causes a hardware hang on register
access if no_console_suspend command line option is used.
Also, not every of_serial device is an 8250 port, so the serial8250
suspend/resume functions should only be applied to a real 8250 port.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Tested-by: Joseph Lo <josephl@nvidia.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct uart_port.flags field is type upf_t, as are the matching
bit definitions. Change local mask variable to type upf_t.
Fixes sparse warnings:
drivers/tty/serial/serial_core.c:620:22: warning: invalid assignment: |=
drivers/tty/serial/serial_core.c:620:22: left side has type unsigned int
drivers/tty/serial/serial_core.c:620:22: right side has type restricted upf_t
drivers/tty/serial/serial_core.c:622:22: warning: invalid assignment: |=
drivers/tty/serial/serial_core.c:622:22: left side has type unsigned int
drivers/tty/serial/serial_core.c:622:22: right side has type restricted upf_t
drivers/tty/serial/serial_core.c:624:17: warning: restricted upf_t degrades to integer
drivers/tty/serial/serial_core.c:626:22: warning: invalid assignment: &=
drivers/tty/serial/serial_core.c:626:22: left side has type unsigned int
drivers/tty/serial/serial_core.c:626:22: right side has type restricted upf_t
drivers/tty/serial/serial_core.c:629:20: warning: restricted upf_t degrades to integer
drivers/tty/serial/serial_core.c:632:20: warning: restricted upf_t degrades to integer
drivers/tty/serial/serial_core.c:643:22: warning: invalid assignment: |=
drivers/tty/serial/serial_core.c:643:22: left side has type unsigned int
drivers/tty/serial/serial_core.c:643:22: right side has type restricted upf_t
drivers/tty/serial/serial_core.c:645:22: warning: invalid assignment: |=
drivers/tty/serial/serial_core.c:645:22: left side has type unsigned int
drivers/tty/serial/serial_core.c:645:22: right side has type restricted upf_t
drivers/tty/serial/serial_core.c:647:17: warning: restricted upf_t degrades to integer
drivers/tty/serial/serial_core.c:649:22: warning: invalid assignment: &=
drivers/tty/serial/serial_core.c:649:22: left side has type unsigned int
drivers/tty/serial/serial_core.c:649:22: right side has type restricted upf_t
drivers/tty/serial/serial_core.c:652:20: warning: restricted upf_t degrades to integer
drivers/tty/serial/serial_core.c:655:20: warning: restricted upf_t degrades to integer
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 299245a145,
serial: core: Privatize modem status enable flags, introduced
the upstat_t type and matching bit definitions. The purpose is to
produce sparse warnings if the wrong bit definitions are used
(by warning of implicit integer conversions).
Fix implicit conversion to integer return type from uart_cts_enabled()
and uart_dcd_enabled().
Fixes the following sparse warnings:
drivers/tty/serial/serial_core.c:63:30: warning: incorrect type in return expression (different base types)
drivers/tty/serial/serial_core.c:63:30: expected int
drivers/tty/serial/serial_core.c:63:30: got restricted upstat_t
include/linux/serial_core.h:364:30: warning: incorrect type in return expression (different base types)
include/linux/serial_core.h:364:30: expected bool
include/linux/serial_core.h:364:30: got restricted upstat_t
include/linux/serial_core.h:364:30: warning: incorrect type in return expression (different base types)
include/linux/serial_core.h:364:30: expected bool
include/linux/serial_core.h:364:30: got restricted upstat_t
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_get_baud_rate() will return baud == 0 if the max rate is set
to the "magic" 38400 rate and the SPD_* flags are also specified.
On the first iteration, if the current baud rate is higher than the
max, the baud rate is clamped at the max (which in the degenerate
case is 38400). On the second iteration, the now-"magic" 38400 baud
rate selects the possibly higher alternate baud rate indicated by
the SPD_* flag. Since only two loop iterations are performed, the
loop is exited, a kernel WARNING is generated and a baud rate of
0 is returned.
Reproducible with:
setserial /dev/ttyS0 spd_hi base_baud 38400
Only perform the "magic" 38400 -> SPD_* baud transform on the first
loop iteration, which prevents the degenerate case from recognizing
the clamped baud rate as the "magic" 38400 value.
Reported-by: Robert Święcki <robert@swiecki.net>
Cc: <stable@vger.kernel.org> # all
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
The atmel serial driver uses dmaengine APIs but never included the dmaengine
header as it was getting inculded thru one of driver headers.
commit 3d588f83e4 - "dmaengine: dw: split
dma-dw.h to platform and private parts" broke this as it moved headers
around. Fix this by doing the right thing to include the dmaengine header
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 08f738be88 (serial: at91: add tx dma support)
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelog below.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aDwACgkQMUfUDdst+ymueACeI1i2exlGaBBSVQuUK2Jmx8Uz
nukAn3KPuvvx+MKfMMBRpK0DQCzTxv4P
=dwv1
-----END PGP SIGNATURE-----
Merge tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver patchset for 3.18-rc1.
Lots of little things in here, some good work from Peter Hurley on the
tty core, and in lots of drivers. There are also lots of other driver
updates in here as well, full details in the changelogs.
All have been in the linux-next tree for a while"
* tag 'tty-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (99 commits)
Revert "serial/core: Initialize the console pm state"
tty: serial: 8250: use 32bit variable for rpm_tx_active
tty: serial: msm: Add earlycon support
serial/core: Initialize the console pm state
serial: asc: Conditionally use readl_relaxed (COMPILE_TEST)
serial: of-serial: add PM suspend/resume support
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
asm/uapi: Add definition of TIOC[SG]RS485
tty/metag_da: Add console_poll module parameter
serial: 8250_pci: remove rts_n override from Baytrail quirk
serial: cadence: Add generic earlycon support
serial: imx: change the wait even to interruptiable
serial: imx: terminate the RX DMA when the UART is suspending
serial: imx: fix throttle/unthrottle callbacks for hardware assisted flow control
serial: 8250: Add Quark X1000 to 8250_pci.c
tty: omap-serial: pull out calculation from baud_is_mode16
tty: omap-serial: fix division by zero
xen_hvc: no reason to write the type key on xenstore
tty: serial: 8250_core: remove UART_IER_RDI in serial8250_stop_rx()
tty: serial: 8250_core: use the ->line argument as a hint in serial8250_find_match_or_unused()
...
Cheers,
Rusty.
PS. My virtio-next tree is empty: DaveM took the patches I had. There might
be a virtio-rng starvation fix, but so far it's a bit voodoo so I will
get to that in the next two days or it will wait.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QzCn
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"Nothing major: support for compressing modules, and auto-tainting
params.
PS. My virtio-next tree is empty: DaveM took the patches I had. There
might be a virtio-rng starvation fix, but so far it's a bit voodoo
so I will get to that in the next two days or it will wait"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
moduleparam: Resolve missing-field-initializer warning
kbuild: handle module compression while running 'make modules_install'.
modinst: wrap long lines in order to enhance cmd_modules_install
modsign: lookup lines ending in .ko in .mod files
modpost: simplify file name generation of *.mod.c files
modpost: reduce visibility of symbols and constify r/o arrays
param: check for tainting before calling set op.
drm/i915: taint the kernel if unsafe module parameters are set
module: add module_param_unsafe and module_param_named_unsafe
module: make it possible to have unsafe, tainting module params
module: rename KERNEL_PARAM_FL_NOARG to avoid confusion
This reverts commit a86713b153.
Kevin Hilman writes:
Multiple boot failures on ARM[1] were bisected down to this
patch.
How was this patch tested, and on which platforms?
Also, the changelog states that this should be done only for
UART_CAP_SLEEP, but the patch does it for every UART.
Greg, I suggest this patch be dropped from tty-next until it has
been better described and tested.
[1] http://lists.linaro.org/pipermail/kernel-build-reports/2014-October/005550.html
Reported-by: Kevin Hilman <khilman@kernel.org>
Cc: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DT based and command line based early console on platforms
with the msm serial hardware.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For console devices having UART_CAP_SLEEP capability, the uart_pm_state has
to be initialized to UART_PM_STATE_ON. Otherwise the LCR regiser values
are reinitialized when uart_change_pm is called from uart_configure_port.
Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 08177ece59 ("serial: asc: Adopt readl_/writel_relaxed()) is
regressing the m68k allmodconfig build. This is due to the unconditional
use of readl_relaxed() which, although documented, does not currently
exist for m68k.
This is trivially fixable for st-asc because we can just update the
asc_in() accessor to make this conditional.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds PM suspend/resume support for the of-serial driver
to provide power management support on devices attatched to it.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should not be used together with Auto Flow Control, and
Auto Flow Control is always enabled on Baytrail.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add earlycon support for the cadence serial port.
This is based on recent patches:
"tty/serial: pl011: add generic earlycon support"
(sha1: 0d3c673e78)
"tty/serial: add arm/arm64 semihosting earlycon"
(sha1: d50d7269eb)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait_event() makes the application hang for ever in the following case:
[1] the hardware flow control is enabled.
[2] the other end (or the remote end) is terminated, and the TX is still
waiting for the hardware flow control signal to become asserted.
This patch fixes it by changing the wait_event to wait_event_interruptible.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the uart port is suspending, the RX data is useless.
So in this case, we can terminate the RX DMA right now.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the 'CTSC' bit is negated. 'CTS' has no function when 'CTSC' is asserted.
0: The CTS pin is high (inactive)
1: The CTS pin is low (active)
For throttle, it needs to clear 'CTS' and 'CTSC' bits.
For unthrottle, it needs to enable 'CTS' and 'CTSC' bits.
The patch just fix the issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.
Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.
This patch enables standard 8250 mode
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To determine the correct divisor, we need to know the difference between
the desired baud rate and the actual baud rate. The calculation for this
difference is implemented twice within omap_serial_baud_is_mode16().
Pull out the calculation for easier maintenance.
While at it, remove the CamelCasing from the variable names.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.
Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() adds UART_IER_RDI and UART_IER_RLSI to ier.
serial8250_stop_rx() should remove both.
This is what the serial-omap driver has been doing and is now moved to
the 8250-core since it does no look to be *that* omap specific.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony noticed that the old omap-serial driver picked the uart "number"
based on the hint given from device tree or platform device's id.
The 8250 based omap driver doesn't do this because the core code does
not honour the ->line argument which is passed by the driver.
This patch aims to keep the same behaviour as with omap-serial. The
function will first try to use the line suggested ->line argument and
then fallback to the old strategy in case the port is taken.
That means the the third uart will always be ttyS2 even if the previous
two have not been enabled in DT.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:
|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
|Control: 10c5387d Table: 80004019 DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.
NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.
v5…v8:
- drop RPM from serial8250_set_mctrl() it will be used in
restore path which already has RPM active and holds
dev->power.lock
v4…v5:
- add a wrapper around rpm function and introduce UART_CAP_RPM
to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
- added runtime to the console code
- removed device_may_wakeup() from serial8250_set_sleep()
Cc: mika.westerberg@linux.intel.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART provides support for HW assisted flow control. What is
missing is the support to throttle / unthrottle callbacks which are used
by the omap-serial driver at the moment.
This patch adds the callbacks. It should be safe to add them since they
are only invoked from the serial_core (uart_throttle()) if the feature
flags are set.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_set_termios() is called with interrupts enabled; no need to
save and restore the interrupt state when taking the uart port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 64851636d5,
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS,
open-codes uart_handle_cts_change() when CONFIG_SERIAL_BFIN_HARD_CTSRTS
to skip start and stop tx.
But the CTS interrupt handler _still_ calls uart_handle_cts_change();
only call uart_handle_cts_change() if !CONFIG_SERIAL_BFIN_HARD_CTSRTS.
cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->hw_stopped is not used by the tty core and is thread-unsafe;
hw_stopped is a member of a bitfield whose fields are updated
non-atomically and no lock is suitable for serializing updates.
Replace serial core usage of tty->hw_stopped with uport->hw_stopped.
Use int storage which works around Alpha EV4/5 non-atomic byte storage,
since uart_port uses different locks to protect certain fields within the
structure.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core uses the tty port flags, ASYNC_CTS_FLOW and
ASYNC_CD_CHECK, to track whether CTS and DCD changes should be
ignored or handled. However, the tty port flags are not safe for
atomic bit operations and no lock provides serialized updates.
Introduce the struct uart_port status field to track CTS and DCD
enable states, and serialize access with uart port lock. Substitute
uart_cts_enabled() helper for tty_port_cts_enabled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core provides two helper functions, uart_handle_dcd_change()
and uart_handle_cts_change(), for UART drivers to use at interrupt
time. The serial core expects the UART driver to hold the uart port lock
when calling these helpers to prevent state corruption.
If lockdep enabled, trigger a warning if the uart port lock is not held
when calling these helper functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are trying to smoke out the use of the return value from
gpiochip_remove() from the kernel, this has been missed.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes COMPILE_TEST build of serial_mctrl_gpio module for
architectures with custom termios.h header.
sparc64:allmodconfig:
In file included from drivers/tty/serial/serial_mctrl_gpio.c:21:0:
include/uapi/asm-generic/termios.h:22:8: error: redefinition of 'struct termio'
./arch/sparc/include/uapi/asm/termbits.h:16:8: note: originally defined here
make[3]: *** [drivers/tty/serial/serial_mctrl_gpio.o] Error 1
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add new PCI IDs to cover newer Intel SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
That field has been deprecated in favour of getting the necessary information
from ACPI or DT.
However, we still need to deal systems that are PCI only (no ACPI to back up)
like Intel Bay Trail. In order to support such systems, we explicitly bind
setup() to the appropriate DMA filter function and its corresponding parameter.
Then when serial8250_request_dma() doesn't find the channel via ACPI or DT, it
falls back to use the given filter function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device has a highspeed register which influences the calcualtion
of the divisor. The chip lacks support for some baudrates. When requested,
we set the divisor to the next smaller baudrate and adjust the c_cflag
accordingly.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The architectures supported by this driver, arm and sh, have expensive
implementations of writel(), reliant on spin locks and explicit L2 cache
management. These architectures provide a cheaper writel_relaxed() which
is much better suited to peripherals that do not perform DMA. The
situation with readl()/readl_relaxed()is similar although less acute.
This driver does not use DMA and will be more power efficient and more
robust (due to absence of spin locks during console I/O) if it uses the
relaxed variants.
The driver supports COMPILE_TEST and therefore falls back to writel()
when writel_relaxed() does not exist.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: kernel@stlinux.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch fixes the following build error of CLPS711X serial driver for
targets without GPIOLIB support:
>> drivers/tty/serial/serial_mctrl_gpio.c:44:6: error: redefinition of 'mctrl_gpio_set'
void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl)
^
In file included from drivers/tty/serial/serial_mctrl_gpio.c:23:0:
drivers/tty/serial/serial_mctrl_gpio.h:80:6: note: previous definition of 'mctrl_gpio_set' was here
void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl)
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit: e676253b19 [3/21] serial/8250: Add
support for RS485 IOCTLs, adds a building error on arch m32r.
All error/warnings:
drivers/tty/serial/8250/8250_core.c: In function 'serial8250_ioctl':
>> drivers/tty/serial/8250/8250_core.c:2859:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
if (copy_from_user(&rs485_config, (void __user *)arg,
^
>> drivers/tty/serial/8250/8250_core.c:2871:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
if (copy_to_user((void __user *)arg, &up->rs485,
^
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_empty() callback currently checks the TXEMPTY bit in the interrupt
status register to decided whether the FIFO should be reported as empty or
not. The bit in this register gets set when the FIFO state transitions from
non-empty to empty but is cleared again in the interrupt handler. This means
it is not suitable to be used to decided whether the FIFO is currently empty
or not. Instead use the TXEMPTY bit from the status register which will be
set as long as the FIFO is empty.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In set_termios(), interrupts where not disabled if UART_ENABLE_MS() was
false.
Tested on at91sam9g35.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # >= 3.16
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another new ACPI identifier for the 8250 dw bindings to cover newer Intel
SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP version of the 8250 can actually use 1:1 serial8250_startup().
However it needs to be extended by a wake up irq which should to be
requested & enabled at ->startup() time and disabled at ->shutdown() time.
v2…v3: properly copy callbacks
v1…v2: add shutdown callback
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no way to access a struct uart_8250_port for a specific
line. This is only required outside of the 8250/uart callbacks like for
devices' suspend & remove callbacks. For those the 8250-core provides a
wrapper like serial8250_unregister_port() which passes the struct
to the proper function based on the line argument.
For run time suspend I need access to this struct not only to make
serial_out() work but also to properly restore up->ier and up->mcr.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code relies on the UART clock pre-divisor to be already
configured in the baud rate register. Calculate it in the driver
and set explicitly instead, also return the "real" effective baud
rate, which is generally slightly different from the requested value.
While at this, also ensure that break signal timing is updated when
baud rate changes.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds simple polling functions for single-character transmit
and receive, as used by kgdb.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer WonderMedia chips introduced another flag in the UART line control
register, which controls whether RTS/CTS signalling should be handled in
the driver or by the hardware itself.
This patch ensures that the kernel can control RTS/CTS (including
disabling it altogether) by forcing this flag to software mode on affected
chips (only WM8880 so far).
Also remove the redundant copy of the binding doc, while we are here.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present this console is optionally registered by NULL checking
arch_kgdb_ops.enable_nmi. In practice this requires the architecture
dependant code to implement some kind of control (e.g. module arguments)
to enable/disable this feature.
The kernel already provides us the perfectly adequate console= argument
to enable/disable consoles. Let's use that instead!
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Universally adopt container_of() for all pointer conversion from
uart_port to uart_amba_port.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking at the get_poll_char() function of the 8250.c serial driver,
we learn:
* poll_get_char() doesn't have to save/disable/restore the interrupt
registers. No interrupt handling is needed in this function at all.
Remove it.
* Don't block in case there is no data available. So instead blocking
in the do {} while loop, just return with NO_POLL_CHAR, immediately .
Additionally, while the i.MX6 register URXD[7-0] contain the RX_DATA,
the upper bits of this register (URXD[15-10]) might contain some
control flags. To ensure that these are not returned with the data
read, just mask out URXD[7-0].
These changes fix the 'hang' working with kdb:
$ echo ttymxc3 > /sys/module/kgdboc/parameters/kgdboc
$ echo g >/proc/sysrq-trigger
[0]kdb> help
...
<hang>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for spin lock assertion; move non-trivial assignment into
function body.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing callers of serial8250_modem_status() [1] hold the uart port
lock; document.
[1] In-tree callers of serial8250_modem_status()
drivers/tty/serial/8250/8250_fsl.c
fsl8250_handle_irq()
drivers/tty/serial/8250/8250_core.c
serial8250_handle_irq()
serial8250_console_write()
serial8250_get_mctrl() *
* Call graphs for callers of serial8250_get_mctrl() from the function
which acquires the uart port lock
drivers/tty/serial/serial_core.c
uart_port_startup()
uart_tiocmget()
uart_set_termios()
uart_carrier_raised()
ops->get_mctrl() ---> serial8250_get_mctrl()
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_SERIAL_BFIN_CTSRTS is set, compile fails because of missing
declarations for the gpio_* api. Include necessary header.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core may call the UART driver's start_tx() even if
tx is stopped; the UART driver must verify tx should be enabled
before transmitting.
Reported-by: Sam Ravnborg <sam@ravnborg.org>
cc: David S. Miller <davem@davemloft.net>
cc: <sparclinux@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mpc52xx_uart_send_xchar() is _identical_ to the default serial core
x_char handling behavior in uart_send_xchar().
Remove mpc52xx_uart_send_xchar().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
START_CHAR() & STOP_CHAR() can be disabled if set to '\0'
(__DISABLED_CHAR). UART drivers which define a send_xchar()
handler must not transmit __DISABLED_CHAR.
Document requirement.
Affected drivers:
sunsab
sunhv
cc: David S. Miller <davem@davemloft.net>
cc: <sparclinux@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_unthrottle() attempts to avoid sending START and the previous
x_char if the previous x_char has not yet been sent. However, this
optimization could leave the sender in a throttled state; for example,
if the sender is throttled and this unthrottle coincides with a manual
tcflow(TCION) from user-space, then neither START would be sent.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART driver is expected to clear port->x_char after
transmission while holding the port->lock. However, the serial
core fails to take the port->lock before assigning port->xchar.
This allows for the following race
CPU 0 | CPU 1
|
| serial8250_handle_irq
| ...
| serial8250_tx_chars
| if (port->x_char)
| serial_out(up, UART_TX, port->x_char)
uart_send_xchar |
port->x_char = ch |
| port->x_char = 0
port->ops->start_tx() |
|
The x_char on CPU 0 will never be sent.
Take the port->lock in uart_send_xchar() before assigning port->x_char.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core expects the UART driver to transmit x_char
(START/STOP chars) even if tx is stopped and before data already
in the tx ring buffer if possible. Also, sending x_char must
not cause additional data in the tx ring buffer to transmit
if tx is stopped.
Cause x_char to be transmitted before any other data is sent.
Auto-stop tx if the tx ring buffer is empty or tx should be stopped.
Only perform one write wakeup if tx ring buffer space is below
threshold.
x_char handling in DMA mode is still broken; add FIXME.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 06aa82e498.
This commit purports to enable auto CTS flow control for the 8250
UART driver. However, the 8250 UART driver already supports auto
CTS flow control via UART_CAP_AFE and UART_CAP_EFR. Indeed, this
patch introduces another DT attribute for which an existing firmware
flag already exists ("auto-flow-control"). Furthermore, the use of
UPF_HARD_FLOW requires the UART driver to define .throttle and
.unthrottle methods, neither of which are defined for the 8250 UART
driver (which will result in a NULL ptr dereference). Finally, this patch
supposes to fix existing bugs in the serial core for auto CTS-enabled
hardware, but does not include the class of hardware for which these
bugs exist.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete successive assignments to the same location.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoC has four fully functional UARTs which use the same programming
model. They are named UART_A, UART_B, UART_C and UART_AO (Always-On)
which cannot be powered off.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The symbol is defined in drivers/tty/serial/8250/Kconfig as
"SERIAL_8250", not just "8250".
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Frank reports that after continuing in kgdb the RX stale event
doesn't occur until after the RX fifo is filled up with exactly
the amount of characters programmed for the RX watermark (in this
case it's 48). To read a single character from the uartdm
hardware we force a stale event so that any characters in the RX
packing buffer are flushed into the RX fifo immediately instead
of waiting for a stale timeout or for the fifo to fill. Forcing
that stale event asserts the stale interrupt but we never clear
that interrupt via UART_CR_CMD_RESET_STALE_INT in the polling
functions. So when kgdb continues the stale interrupt is left
pending in the hardware and we don't timeout with a stale event,
like we usually would if a user typed one character on the
console, until the reset stale interrupt and stale event commands
are sent. Frank could get things working again by running
handle_rx_dm(). By putting enough characters into the fifo he
could trigger a watermark interrupt, and thus cause
handle_rx_dm() to run finally resetting the stale interrupt
and enabling the stale event so that single characters would
cause timeouts again.
The fix is to just do what the interrupt routine was doing all
along and clear the stale interrupt and enable the event again.
Doing this also smooths over any differences in the fifo behavior
between v1.3 and v1.4 hardware allowing us to skip forcing the
uart into single character mode.
Reviewed-by: Frank Rowand <frank.rowand@sonymobile.com>
Tested-by: Frank Rowand <frank.rowand@sonymobile.com>
Fixes: f7e54d7ad7 "msm_serial: Add support for poll_{get,put}_char()"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CLPS711X serial driver uses the system wide registers to control the
modem signals. Now gpio-syscon driver can be used for this purposes.
mctrl_gpio helpers allow us to create GPIO bindings for any of modem/tty
control signals that extends the functionality of the driver.
This patch makes such change.
This change does not break any current DT bindings, since DT support
for this platform is not introduced yet.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
printk replaced with corresponding dev_* .
fixed two broken user-visible strings used by the corresponding printk.
the null check for uport->dev and port->dev is removed as dev_* will check for
null while printing.
printing of dev_name(uport->dev) and dev_name(port->dev) also removed as those
are being printed by dev_* .
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the of_device_id arrays const, as it is handled as const by all OF
functions.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed below checkpatch.pl warning:
WARNING: else is not generally useful after a break or return
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes below checkpatch.pl warning and it remove extra blank lines:
WARNING: Missing a blank line after declarations
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed below checkpatch.pl warning:
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch lets you set the RS485 cappabilites of the device through
TIOCSRS485 and TIOCGRS485 as defined on Documentation/serial/serial-rs485.txt
In order to probe the device, the PNP id and the device id is used.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allow the users of the 8250 infrastructure to define a
handler for RS485 configration.
If no handler is defined the 8250 driver will work as usual.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
--
v2:Change suggested by Alan "One Thousand Gnomes":
- Move rs485 structure further down on the uart_8250_port structure
drivers/tty/serial/8250/8250_core.c | 39 +++++++++++++++++++++++++++++++++++++
include/linux/serial_8250.h | 3 +++
2 files changed, 42 insertions(+)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device ids for additional Neo cards. The ids come from the dgnc
driver.
Signed-off-by: Bill Pemberton <wfp5p@worldbroken.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add flags field to struct kernel_params, and add the first flag: unsafe
parameter. Modifying a kernel parameter with the unsafe flag set, either
via the kernel command line or sysfs, will issue a warning and taint the
kernel.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Jon Mason <jon.mason@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
Pull sparc updates from David Miller:
1) Add sparc RAM output to /proc/iomem, from Bob Picco.
2) Allow seeks on /dev/mdesc, from Khalid Aziz.
3) Cleanup sparc64 I/O accessors, from Sam Ravnborg.
4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do
not insert it into the TLB miss hash tables otherwise we'll
livelock. Based upon work by Christopher Alexander Tobias Schulze.
5) Fix BREAK detection in sunsab driver when no actual characters are
pending, from Christopher Alexander Tobias Schulze.
6) Because we have modules --> openfirmware --> vmalloc ordering of
virtual memory, the lazy VMAP TLB flusher can cons up an invocation
of flush_tlb_kernel_range() that covers the openfirmware address
range. Unfortunately this will flush out the firmware's locked TLB
mapping which causes all kinds of trouble. Just split up the flush
request if this happens, but in the long term the lazy VMAP flusher
should probably be made a little bit smarter.
Based upon work by Christopher Alexander Tobias Schulze.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
sparc64: Fix up merge thinko.
sparc: Add "install" target
arch/sparc/math-emu/math_32.c: drop stray break operator
sparc64: ldc_connect() should not return EINVAL when handshake is in progress.
sparc64: Guard against flushing openfirmware mappings.
sunsab: Fix detection of BREAK on sunsab serial console
bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000
sparc64: Do not insert non-valid PTEs into the TSB hash table.
sparc64: avoid code duplication in io_64.h
sparc64: reorder functions in io_64.h
sparc64: drop unused SLOW_DOWN_IO definitions
sparc64: remove macro indirection in io_64.h
sparc64: update IO access functions in PeeCeeI
sparcspkr: use sbus_*() primitives for IO
sparc: Add support for seek and shorter read to /dev/mdesc
sparc: use %s for unaligned panic
drivers/sbus/char: Micro-optimization in display7seg.c
display7seg: Introduce the use of the managed version of kzalloc
sparc64 - add mem to iomem resource
Fix detection of BREAK on sunsab serial console: BREAK detection was only
performed when there were also serial characters received simultaneously.
To handle all BREAKs correctly, the check for BREAK and the corresponding
call to uart_handle_break() must also be done if count == 0, therefore
duplicate this code fragment and pull it out of the loop over the received
characters.
Patch applies to 3.16-rc6.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA is a function 0 of the multifunction device where SPI host is attached.
Thus, we may avoid to hardcode PCI slot number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The s->clk never gets setup in sc16is7xx_probe() and instead was using a
local clk variable, but then testing the uninitialized s->clk during
teardown
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_dw driver fails to probe if the specified clock isn't
registered at probe time. Even if a clock frequency is given,
the required clock might be gated because it wasn't properly
enabled.
This happened to me when the device is registered through DT,
and the clock was part of an MFD, the PRCM found on A31 and A23
SoCs. Unlike core clocks that are registered with OF_CLK_DECLARE,
which happen almost immediately after the kernel starts, the
clocks are registered as sub-devices of the PRCM MFD platform
device. Even though devices are registered in the order they are
found in the DT, the drivers are registered in a different,
arbitrary order. It is possible that the 8250_dw driver is
registered, and thus associated with the device and probed, before
the clock driver is registered and probed.
8250_dw then reports unable to get the clock, and fails. Without
a working console, the kernel panics.
This patch adds support for deferred probe handling for the clock
and reset controller. It also fixes the cleanup path if
serial8250_register_8250_port fails.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Allwinner A31 and A23 SoCs have a reset controller
maintaining the UART in reset by default.
This patch adds optional reset support to the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current calculation, if the required baud rate is above 262143,
we get an overflow.
This patch uses a 64bits variable to do the maths.
Also, we remove the '+1' to avoid a divide by zero if the input clock
rate is something unexpected.
Indeed, if the input clock rate is zero, it is preferable to be notified,
since the UART won't work anyway.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to prevent an asc instance to be used as early console, BUG_ON is
used on either mapbase or membase being NULL.
Problem is that this condition is also true when we set console to be a ttyASx
different to the first asc instance being probed.
Instead of calling BUG_ON, it now returns -ENXIO when either mapbase or
membase is NULL.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code allocates too much data for tty_groups member of uart_port struct,
so fix it.
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3d1c90d48c ("serial: altera_jtaguart: Adpot
uart_console_write()") introduced the usage of uart_console_write() but
didn't change the signature of altera_jtaguart_console_putc() to take a
pointer to struct uart_port instead of struct console, breaking the
driver's console support and leading to the following warning:
> drivers/tty/serial/altera_jtaguart.c: In function 'altera_jtaguart_console_write':
> >> drivers/tty/serial/altera_jtaguart.c:350:2: warning: passing argument 4 of 'uart_console_write' from incompatible pointer type [enabled by default]
> uart_console_write(port, s, count, altera_jtaguart_console_putc);
> ^
> In file included from drivers/tty/serial/altera_jtaguart.c:25:0:
> include/linux/serial_core.h:317:6: note: expected 'void (*)(struct uart_port *, int)' but argument is of type 'void (*)(struct console *, int)'
> void uart_console_write(struct uart_port *port, const char *s,
Fix this by adjusting the signature of altera_jtaguart_console_putc()
accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All Samsung platforms are now using the Common Clock Framework and the
legacy clock code is being removed, so remove related dead code from
samsung-serial driver as well.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add tunable RX interrupt trigger I/F of FIFO buffers.
Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.
According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.
This patch makes some devices change RX interrupt trigger from userland.
<How to use>
- Read current setting
# cat /sys/class/tty/ttyS0/rx_trig_bytes
8
- Write user setting
# echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
# cat /sys/class/tty/ttyS0/rx_trig_bytes
1
<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)
<Change log>
Changes in V9:
- Use attr_group instead of dev_spec_attr_group of uart_port structure
Changes in V8:
- Divide this patch from V7's patch based on Greg's comment
Changes in V7:
- Add Documentation
- Change I/F name from rx_int_trig to rx_trig_bytes because the name
rx_int_trig is hard to understand how users specify the value
Changes in V6:
- Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
UART_FCR_R_TRIG_BITS()
- Change following function names:
convert_fcr2val() => fcr_get_rxtrig_bytes()
convert_val2rxtrig() => bytes_to_fcr_rxtrig()
- Fix typo in serial8250_do_set_termios()
- Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
- Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
(but UI remains rx_int_trig)
- Change the meaningless variable name 'val' to 'bytes' following functions:
fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
- Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
fcr_get_rxtrig_bytes()
- Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
in register_dev_spec_attr_grp()
- Delete the checking whether a user changed FCR or not when minimum buffer
is needed in serial8250_do_set_termios()
Changes in V5.1:
- Fix FCR_RX_TRIG_MAX_STATE definition
Changes in V5:
- Support Tegra, 16650V2, 16654, and 16750
- Store default FCR value to up->fcr when the port is first created
- Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
in convert_fcr2val() and convert_val2rxtrig()
Changes in V4:
- Introduce fifo_bug flag in uart_8250_port structure
This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
for up->bugs. If this flag is enabled, user cannot set RX trigger.
- Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
at convert_val2rxtrig()
- Set the nearest lower RX trigger when users input a meaningless value at
convert_val2rxtrig()
- Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
- Set fcr = up->fcr in the begging of serial8250_do_set_termios()
Changes in V3:
- Change I/F from ioctl(2) to sysfs(rx_int_trig)
Changed in V2:
- Use _IOW for TIOCSFIFORTRIG definition
- Pass the interrupt trigger value itself
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some serial drivers (like 8250), want to add sysfs files. We need to do
so in a race-free way, so allow any port to be able to specify an
attribute group that should be added at device creation time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present it is not possible to boot with the ttyNMI0 console treating
character input normally, instead character input triggers a prompt
telling the user how to trigger the knock detector and enter the
debugger. To use the console normally requires that kdb be entered and
the nmi_console command be used to enable the console (or if only kgdb
is present then gdb must directly manipulate the value of
kgdb_nmi_tty_enabled).
This patch automates the management of kgdb_nmi_tty_enabled by keeping
track of the number of file handles that are open for reading and using
that to determine how to tty should operate.
The approach means that:
1. Behaviour before init starts is unchanged.
2. If the userspace runs a getty or some other interactive process on
/dev/console (or explicitly on /dev/ttyNMI0) the tty will treat
character input like any other tty.
3. If the userspace doesn't use /dev/console or if it uses /dev/console
only to log messages (O_WRONLY) then the user prompt is retained.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow commit 2970b7f5ea ("serial: altera: Adopt
uart_console_write()") and don't open code the LF to LFCR conversion in
altera_jtaguart either. Use uart_console_write() instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The of_node is derived from pdev for every usage, define a
device_node variable instead.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cases should comes before default in a switch.
Even if we want the case and default to share same code.
Its good to define the case first followed by default.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART modules on some SoCs only differ in the fifosize of each
UART channel. Its useless to duplicate the drv_data structure
or create a compatible name for such a change.
We can get fifosize via the device tree nodes (not mandating it).
Also updates the documentation.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It helps to cast struct uart_port to struct uart_8250_port at runtime.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This add the 32-bit register version LPUART support with big-endian
byte order.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the error of the same bit rate is detected, we will need to select
the recive margin is large. Current code holds the minimum error, it does
not have to check the recive margin. This adds this calculation.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If bit-rate calculation result of HSCIF is expect 255 from 0,
driver does not calculate error bit. However, we need to round
the value to calculate error bit in the case of negative value.
This rounds the value of bit-rate using clamp(), and bit-rate is the
case of negative value, it enables the calculation of the error bit.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the decimal point is discarded calculation of BRR.
Therefore, it can not calculate a value close to the correct value.
This patch fixes this problem by using DIV_ROUND_CLOSEST.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 16052827d9 ("dmaengine/dma_slave:
introduce inline wrappers") changed the code to use the new API, but forgot
to update an error message.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-serial@vger.kernel.org
--
v2:
- New
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| drivers/tty/serial/arc_uart.c:516:2: warning: (near initialization for 'arc_serial_pops.poll_put_char') [enabled by default]
This partially undoes "serial/arc: use uart_console_write() helper" by
restoring the prototpye of poll helper and use a different one in
uart_console_write()
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver does not currently use uart_console_write() and instead
provides is own LF to LFCR conversion in it's console_write() method.
We should use the library function instead.
Cmopile tested only (with ARCH=arm).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: nios2-dev@lists.rocketboards.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Olof Johansson pointed out that usually the company name is picked as
namespace prefix to specific properties. So expect "energymicro,location"
but fall back to the previously introduced name "efm32,location".
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix breakage introduced by
commit c557d392fb,
'serial: Test for no tx data on tx restart'.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open-coded test for empty tx ring buffer with equivalent
helper function, uart_circ_empty(). No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 717f3bbab3,
'serial_core: Fix conditional start_tx on ring buffer not empty'
exposes an incorrect assumption in several drivers' start_tx methods;
the tx ring buffer can, in fact, be empty when restarting tx while
performing flow control.
Affected drivers:
sunsab.c
ip22zilog.c
pmac_zilog.c
sunzilog.c
m32r_sio.c
imx.c
Other in-tree serial drivers either are not affected or already
test for empty tx ring buffer before transmitting.
Test for empty tx ring buffer in start_tx() method, after transmitting
x_char (if applicable).
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Seth Bollinger <sethb@digi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support big-endian CPUs use the string versions of the io
read/write macros on the TX/RX fifos and the non-raw variants of
the readl/writel macros throughout. This way we don't byteswap
the characters coming from the fifos but we properly deal with
the little-endian nature of the serial hardware while controlling
it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TXX9_SIFCR_TDIL_MASK define is cut and pasted twice so we can delete
the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
blackfin uart port drivers mistakenly set the struct uart_port
flags bit UPF_BUG_THRE (which only has meaning to the 8250 core)
while trying to set ASYNC_CTS_FLOW.
Uart port drivers can override termios settings based on actual
hardware support in their .set_termios method; the serial core
sets the appropriate port flags based on the overrides.
Overriding only the initial termios settings is accomplished
by only perform those overrides if the old termios parameter is
NULL.
CC: Sonic Zhang <sonic.zhang@analog.com>
CC: adi-buildroot-devel@lists.sourceforge.net
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley