Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Sync dtc to upstream commit 0931cea3ba20. This picks up overlay
support in dtc.
- Set dma_ops for reserved memory users.
- Make references to IOMMU consistent in DT bindings.
- Cleanup references to pm_power_off in bindings.
- Move some display bindings that snuck into the old bindings/video/
path.
- Fix some wrong documentation paths caused from binding restructuring.
- Vendor prefixes for Faraday and Fujitsu.
- Fix an of_node ref counting leak in of_find_node_opts_by_path
- Introduce new graph helper of_graph_get_remote_node() which will be
used by DRM drivers in 4.12.
-----BEGIN PGP SIGNATURE-----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=D/BO
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"Pretty standard stuff with dtc upstream sync being the biggest piece.
- Sync dtc to upstream commit 0931cea3ba20. This picks up overlay
support in dtc.
- Set dma_ops for reserved memory users.
- Make references to IOMMU consistent in DT bindings.
- Cleanup references to pm_power_off in bindings.
- Move some display bindings that snuck into the old bindings/video/
path.
- Fix some wrong documentation paths caused from binding
restructuring.
- Vendor prefixes for Faraday and Fujitsu.
- Fix an of_node ref counting leak in of_find_node_opts_by_path
- Introduce new graph helper of_graph_get_remote_node() which will be
used by DRM drivers in 4.12"
* tag 'devicetree-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (27 commits)
DT: add Faraday Tec. as vendor
of: introduce of_graph_get_remote_node
of: Add missing space at end of pr_fmt().
of: make of_device_make_bus_id() static
of: fix of_node leak caused in of_find_node_opts_by_path
dt-bindings: net: remove reference to fixed link support
dt-bindings: power: reset: qnap-poweroff: Drop reference to pm_power_off
dt-bindings: power: reset: gpio-poweroff: Drop reference to pm_power_off
dt-bindings: mfd: as3722: Drop reference to pm_power_off
dt-bindings: display: move ANX7814 and SiI8620 bridge bindings
of/unittest: Swap arguments of of_unittest_apply_overlay()
Documentation: usb: fix wrong documentation paths
serial: fsl-imx-uart.txt: Remove generic property
devicetree: Add Fujitsu Ltd. vendor prefix
Documentation: display: fix wrong documentation paths
of: remove redundant memset in overlay
bus:qcom : Fix typo in qcom,ebi2.txt
dt-bindings: qman: Remove pool channel node
Documentation: panel-dpi: fix path to display-timing.txt
devicetree: bindings: clk: mvebu: fix description for sata1 on Armada XP
...
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
Furthermore add myself as a maintainer for this driver.
The datasheet can be found at the manufacturers website, see [1]. All
device-tree exposed configuration features have been tested on a i.MX6
platform with a USB2512B hub.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/00001692C.pdf
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this series, it adds qualcomm USB2 support. The review process takes
more than half of year, thanks for Stephen Boyd's great work.
Most of patches at linux-next more than ten days, and the last two small
chipidea patches at my tree about one day, no warning is reported from
autobuild robot.
Thanks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYlTjsAAoJEEhZKYFQ1nG7YGYIAI+1uo4Hrfja3IdkPX0jQRc8
BwPE/mR/9r2HKsLrXpFf1fNBvHnUOtHigq5JEV8xVF3USAP+dTmB3kQkk1CowryT
9sdp2/1lGe5GaN2SA4Rbg7spjSE+hsWh369XhvBkkQr1WMkaAxxAOvqnPZN94zey
1W5HB89p8XOSHOY/qljW67v2XAb8zZMRjUGUjDVno/YKBlcFi9jX67HZLOA6ReR4
UQZwqjyNh6ndSIwO0hQr23xpmRuomsFlmVpDBoGq5bwfWXzzjNwKUm5RZr3+uZMo
kY7kD8YgP6yF+WygQ3o35vUkqZ9sSAmxD6Dx/mWSKzxCribEnraBYXKBg2ft688=
=01My
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Hi Greg,
In this series, it adds qualcomm USB2 support. The review process takes
more than half of year, thanks for Stephen Boyd's great work.
Most of patches at linux-next more than ten days, and the last two small
chipidea patches at my tree about one day, no warning is reported from
autobuild robot.
Thanks.
Allwinner H3/V3s features a variant of MUSB controller, which lacks one
endpoint.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[b-liu@ti.com: added usb: to commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
-----BEGIN PGP SIGNATURE-----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=gk8j
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
In case 'quirk-broken-port-ped' property is passed in via device property,
we should enable the corresponding BROKEN_PED quirk flag for XHCI core.
[rogerq@ti.com] Updated code from platform data to device property
and added DT binding.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3 internally creates a usb-xhci device which means that all
properties documented in usb-xhci.txt are supported as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The qcom HSIC ULPI phy doesn't have any bits set in the vendor or
product ID registers. This makes it impossible to make a ULPI
driver match against the ID registers. Add support to discover
the ULPI phys via DT help alleviate this problem. In the DT case,
we'll look for a ULPI bus node underneath the device registering
the ULPI viewport (or the parent of that device to support
chipidea's device layout) and then match up the phy node
underneath that with the ULPI device that's created.
The side benefit of this is that we can use standard properties
in the phy node like clks, regulators, gpios, etc. because we
don't have firmware like ACPI to turn these things on for us. And
we can use the DT phy binding to point our phy consumer to the
phy provider.
The ULPI bus code supports native enumeration by reading the
vendor ID and product ID registers at device creation time, but
we can't be certain that those register reads will succeed if the
phy is not powered up. To avoid any problems with reading the ID
registers before the phy is powered we fallback to DT matching
when the ID reads fail.
If the ULPI spec had some generic power sequencing for these
registers we could put that into the ULPI bus layer and power up
the device before reading the ID registers. Unfortunately this
doesn't exist and the power sequence is usually device specific.
By having the device matched up with DT we can avoid this
problem.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
Adds the device tree bindings description for Samsung S3C2410 and
compatible USB OHCI controller.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for
the ohci controller found in TI da8xx family of SoC's
Cc: robh+dt@kernel.org
Cc: mark.rutland@arm.com
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DT binding for the TI DA8xx/OMAP-L1x/AM17xx/AM18xx MUSB driver.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
This patch adds support for the "amcc,usb-otg" device
which is found in the PowerPC Canyonlands' dts.
The device definition was added by:
commit c89b3458d8 ("powerpc/44x: Add USB DWC DTS entry to Canyonlands
board")
but without any driver support as the dwc2 driver wasn't available at
that time.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for Renesas r8a7796 SoC. This SoC is not
compatible with r8a7795 because using firmware version differs.
Since the "V2" firmware can be used on both r8a7795 (es1.x) and r8a7796,
the "renesas,rcar-gen3-xhci" keeps to use the "V2" for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some resources, such as IPPC register etc, shared with device
driver are moved into common glue layer when xHCI driver is the
host side of dual-role mode and they should be changed as optional
properties if they are required ones before. For clarity, add
a new part of binding to support host side of dual-role mode.
Additionally add optional properties of pinctrl for host only mode
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This binding was deprecated due to commit aa381a7259 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization"). However that
commit is now reverted, so also revert this commit.
The binding is valid and shouldn't be deprecated.
This reverts commit 65e1ff7f4b ("Documentation: devicetree: dwc2:
Deprecate g-tx-fifo-size").
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
disable io watchdog for chipidea platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX2lExAAoJEEhZKYFQ1nG7xVkH/jfONzi6B0o1sPLwA5pF9PEz
mvkCUaXMRmgeHcHPviXjthfbZ6eKR7ddd0bxGC3DWd4eUOO3QohW9vI+wYhpKk//
mQh2F25nvZNYKOZ/BdG5XRZjVFT1qJGseknSg0TsRraAVEjOLdr7gqViPRAqMyoJ
PY3CQxlf8dqHz4ed5xsKmwcjGE9Q+A+YMhOXzxY2aLGTCaDNOcYNHJWIe9QXwOVQ
snxiNe+DoPkrspGrUJQpZ7lSq5siNxLS7cOlzYmWvxMkNw2A5xJgnoxoDziey8xo
2F427B0CwXyTC1gNBk721pIjIvkNcPAghoUo8EUgD71hC4nH8EFFM3iqA+U1xpc=
=hww9
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
Most of them are refine patches, only new feature is
disable io watchdog for chipidea platform.
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
-----BEGIN PGP SIGNATURE-----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=vTFa
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
Add compatible strings for amlogic Meson8b and GXBB SoCs with the
corresponding configuration parameters.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Adding over-current-active-high to indicate the over current flag
is high active as typically we use active low for over current
polarity.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Add compatible string for imx7d-usbmisc.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Add necessary compatible flag for Cavium's DWC3 so
dwc3-of-simple will probe.
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This property is not needed because the periodic fifos are not
configurable. So it was incorrect to add this property in the first
place.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for r8a7796 (R-Car M3-W).
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc3 driver expicitly looks for "usb2-phy" or "usb3-phy", but we
never noted these names in the documentation.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds the devicetree documentation required for Rockchip
USB3.0 core wrapper consisting of USB3.0 IP from Synopsys.
It supports DRD mode, and could operate in device mode (SS, HS, FS)
and host mode (SS, HS, FS, LS).
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is a minimal driver to support bringing a usb4604 device
from microchip out of reset and into hub mode. The usb4604 device
is related to the usb3503 device, but it didn't seem close enough
to warrant putting both into the same file. This patch borrows
some of the usb3503 structure and trims it down to just handle
the optional reset gpio and adds the i2c command to put the
device into hub mode.
Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/00001716A.pdf
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
The endpoint nodes have a reg property, they also need a unit-address. Add
them in the example.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The DT bindings example for the Tegra XUSB controller omits the 'lanes'
subnode in the XUSB pad controller which is required according to the DT
bindings documentation for the Tegra XUSB pad controller[0]. In addition
to this the phy-names with the suffix 'utmi' are also not valid and
should have the suffix 'usb2'. Correct both the XUSB pad controller pad
path and phy-names for the XUSB example.
[0]: Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
What the code expect is "itc-setting" rather than "gadget-itc-setting",
and this is also correctly described in the optional properties.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
This reverts commit 7150bc9b4d.
It is not correct, based on review from others.
Reported-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least the EHCI/OHCI found on the Allwinnner H3 SoC needs multiple
reset lines, the controller will not initialize while the reset for
its companion is still asserted, which means we need to de-assert
2 resets for the controller to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to the save power consumption, as a workaround, suspend
forcibly the USB PORTA/B/C via set the SUSPEND_A/B/C bits of OHCI
Interrupt Configuration Register in the SFRs while OHCI USB suspend.
This suspend operation must be done before the USB clock is disabled,
resume after the USB clock is enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of other
stuff.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0P8ACgkQMUfUDdst+ykkFQCg0kJlxIiCU1FYBZYriqo4vX3F
9N8AoM/8nO8Y6vMpF2LWnamafYgqscTE
=ZuCh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of
other stuff.
All have been in linux-next with no reported issues"
* tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits)
USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support
USB: serial: fix minor-number allocation
USB: serial: quatech2: fix use-after-free in probe error path
USB: serial: mxuport: fix use-after-free in probe error path
USB: serial: keyspan: fix debug and error messages
USB: serial: keyspan: fix URB unlink
USB: serial: keyspan: fix use-after-free in probe error path
USB: serial: io_edgeport: fix memory leaks in probe error path
USB: serial: io_edgeport: fix memory leaks in attach error path
usb: Remove unnecessary space before operator ','.
usb: Remove unnecessary space before open square bracket.
USB: FHCI: avoid redundant condition
usb: host: xhci-rcar: Avoid long wait in xhci_reset()
usb/host/fotg210: remove dead code in create_sysfs_files
usb: wusbcore: Do not initialise statics to 0.
usb: wusbcore: Remove space before ',' and '(' .
USB: serial: cp210x: clean up CRTSCTS flag code
USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code
USB: serial: cp210x: fix hardware flow-control disable
USB: serial: option: add even more ZTE device ids
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
Extend the Tegra XUSB controller device tree binding with Tegra210
support.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device-tree binding documentation for the XUSB controller present
on Tegra124 and later SoCs. This controller supports USB 3.0 via an xHCI
compliant interface.
Based on work by Andrew Bresticker <abrestic@chromium.org>.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Even if the Armada 37xx does not any specific setup, the device tree
binding documentation requires to use a SoC-specific version
corresponding to the platform first followed by the generic version.
This patch introduce this new compatible string and updates the
documentation accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Although most of USB devices are hot-plug's, there are still some devices
are hard wired on the board, eg, for HSIC and SSIC interface USB devices.
If these kinds of USB devices are multiple functions, and they can supply
other interfaces like i2c, gpios for other devices, we may need to
describe these at device tree.
In this commit, it uses "reg" in dts as physical port number to match
the phyiscal port number decided by USB core, if they are the same,
then the device node is for the device we are creating for USB core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vivP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb changes for v4.6 merge window
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
Add support for Lantiq ARX and XRX SoC families to the dwc2 driver.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add fallback compatibility strings for R-Car Gen2 and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this property is not set, the max packet size is 1023 bytes, and if
the total of packet size for pervious transactions are more than 256 bytes,
it can't accept any transactions within this frame. The use case is single
transaction, but higher frame rate.
If this property is set, the max packet size is 188 bytes, it can handle
more transactions than above case, it can accept transactions until it
considers the left room size within frame is less than 188 bytes, software
needs to make sure it does not send more than 90%
maximum_periodic_data_per_frame. The use case is multiple transactions, but
less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds the missing compatible strings from ci_hdrc_imx.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LW4w
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
* tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (21 commits)
drivers/of: Export OF changeset functions
Fix documentation for adp1653 DT
ARM: psci: Fix indentation in DT bindings
of/platform: export of_default_bus_match_table
of/unittest: Show broken behaviour in the platform bus
of: fix declaration of of_io_request_and_map
of/address: replace printk(KERN_ERR ...) with pr_err(...)
of/irq: optimize device node matching loop in of_irq_init()
dt-bindings: tda998x: Document the required 'port' node.
net/macb: bindings doc: Merge cdns-emac to macb
dt-bindings: Misc fix for the ATH79 DDR controllers
dt-bindings: Misc fix for the ATH79 MISC interrupt controllers
Documentation: dt: Add bindings for Secure-only devices
dt-bindings: ARM: add arm,cortex-a72 compatible string
ASoC: Atmel: ClassD: add GCK's parent clock in DT binding
DT: add Olimex to vendor prefixes
Documentation: fsl-quadspi: Add fsl,ls1021-qspi compatible string
Documentation/devicetree: document OCTEON USB bindings
usb: misc: usb3503: Describe better how to bind clock to the hub
dt-bindings: Consolidate SRAM bindings from all vendors
...
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vM4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
R-Car H3 has USB3.0 peripheral controllers. This controller's has the
following features:
- Supports super, high and full speed
- Contains 30 pipes for bulk or interrupt transfer
- Contains dedicated DMA controller
This driver doesn't support the dedicated DMAC for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Simply document new compatibility string.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add fallback compatibility strings for R-Car Gen2 and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This extends the documentation of compatibility strings a little to
include the SoC names.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Support hisilicon,hi6220-usb for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Document device-tree bindings for the USB controller on older
OCTEON SOCs (OCTEON, OCTEON+).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Rob Herring <robh@kernel.org>
The R-Car H3 has two xHCI controllers. This SoC is compatible with
R-Car Gen2 SoCs, however this SoC doesn't need some specific registers
setting, and need a new firmware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car M2-N (r8a7793) xHCI controller.
This SoC is compatible with R-Car H2 (r8a7790) and R-Car M2-W (r8a7791).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
Merging in the few patches I had kept separate from main next/dt, since others
got merged here directly.
* next/arm64:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
+ Linux 4.3-rc5
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all dtbs
in the tree for most arches with dts files (except powerpc for now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tGCy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A fairly large (by DT standards) pull request this time with the
majority being some overdue moving DT binding docs around to
consolidate similar bindings.
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
dtbs in the tree for most arches with dts files (except powerpc for
now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options"
* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
MAINTAINERS: update DT binding doc locations
devicetree: add Sigma Designs vendor prefix
of: simplify arch_find_n_match_cpu_physical_id() function
Documentation: arm: Fixed typo in socfpga fpga mgr example
Documentation: devicetree: fix reference to legacy wakeup properties
Documentation: devicetree: standardize/consolidate on "wakeup-source" property
drivers: of: removing assignment of 0 to static variable
xtensa: enable building of all dtbs
mips: enable building of all dtbs
metag: enable building of all dtbs
metag: use common make variables for dtb builds
h8300: enable building of all dtbs
arm64: enable building of all dtbs
arm: enable building of all dtbs
arc: enable building of all dtbs
arc: use common make variables for dtb builds
of: add config option to enable building of all dtbs
of/fdt: fix error checking for earlycon address
of/overlay: add missing of_node_put
of/platform: add missing of_node_put
...
Since the Synopsys DWC3 controller driver inherits the generic bindings
defined in 'usb/generic.txt', this patch tries to capture the same in
the DWC3 binging documentation to avoid any confusion in usage of properties
like 'dr_mode' for certain SoCs like FSL LS2080A.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWKEKdAAoJEEhZKYFQ1nG7dysH/jmFSatDJvgA7woliRZ7p0H/
elNu6AOjqBnsi23Vp54IOVWYTVIDhLsXxlzEOgO6XXfsI99TqFQIIS2VYSo6xues
Eq5hIxh5n9uue3VMnw9bxYHcFkFG9LDAlyMXecEayAB74UqnQLbo2bRDfnSopaf1
dEOq9mdT8llYbtVww6bVXtL78wgwxVk1gTfISllxgt7DEuYwgT+gQJCDLrmkGPn0
XfiaZWamNmDlQd4z/qqoG65+yNmZZMZQKtugCx4MoiBbHVclRN7j2eNsCZ0y6dsZ
qxs+CazL/IeYCqxRRXl5Fopraer1uJeOPeFgA+lRV6WPhMEe7eg6ojkDp/8Y18Y=
=Dh+g
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB Chipidea updates for v4.4-rc1
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jPoY
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.4 merge window
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move USB PHY bindings under usb directory to phy directory which already
contains other USB PHY bindings.
The Samsung USB PHY binding is obsolete and can be removed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Each vendor may have its specific properties, they are not belonged
to common optional properties, split them from common's.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Improve the description of properties "tx-burst-size-dword"
and "rx-burst-size-dword".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shanw Guo <shawnguo@kernel.org>
Add an entry for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power
mode and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a compatible string to support for R-Car H3.
Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a compatible string to support for R-Car H3.
Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add snps,quirk-frame-length-adjustment property which provides value
for post silicon frame length adjustment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Document the binding for the zynq specific chipidea UDC binding.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVzU3lAAoJEEhZKYFQ1nG7nZ4H/AsCAhoiUqcyP4fRziaZzexa
F55CuhIVd6vg6vhuiccoUo4XZXR6IsZikczNowWphqXhtQUBr/rvv0VSb2sMxZfn
AgdNuinhGUat4rdcf0earr9+EQzjbdrHoxDzFKes21S0vS+J3TaYUk6F7Q6sUL81
t97itMmKBrffMZLsQzB9MJo4E8mD4JNlWu/ezGNu11ZD2/w8Ha7GpyExyb2AGHrs
M1rlE6Ph8AKpyECI7OecCxPIDyDRuUQ8Bvj+MkR9BrDX1gOv512ZLfRbIGJCqVOO
A2Urzh/jEI9e7ttGqSpMxGYKZ4wvZ7Ta5IvLLseb0vszM2oQGDNHcJx7fKOuUVU=
=IIud
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB: chipidea updates for v4.3-rc1
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
It is used to override the default setting for burst size, changing
burst size takes effect only when the SBUSCFG.AHBBRST = 0.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
apq8016-sbc board is using Dual SPDT USB Switch (TC7USB40MU),
witch is controlled by GPIO to de/multiplex D+/D- USB lines to
USB2513B Hub and uB connector. Add support for this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add otg version, srp, hnp and adp support for usb OTG port, then those OTG
features don't have to be decided by usb gadget drivers.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.
This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.
This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Driver handles PHY initialization, clock management, power
management and workarounds required after resetting the hardware.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bhUU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late fixes and dependencies from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable BRCMNAND driver
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
ARM: at91/dt: update udc compatible strings
ARM: at91/dt: trivial: fix USB udc compatible string
arm64: dts: Add APM X-Gene standby GPIO controller DTS entries
soc: qcom: spm: Fix idle on THUMB2 kernels
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq
To please checkpatch and the tiresome reader, add the "atmel," prefix to the
USB udc compatible string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #4.0+
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVi4ROAAoJEFk3GJrT+8ZlBcsP/jjXN+pucA3oHE/Jn9j1yF8e
aPENC0iXVDr2ru5SikBlgmBYeoZjsXV90HWnEo3RZrF4/zMa8CUOD6UqKZLp7x9d
SYEtuFk98VM/7Qtho6qDvZaLTnzWT5CL24E+J899P8V9lWVm3mwklKE9ScmkDd5m
kQxtj5rk1HcaDPmtJ0rseqNoaqRSG1UmhAHLkHMYLg5CyQb7L4FZx+l+Zj4FpYFE
js9uIVpp2gIuJu3nLRWgkhnoOVQzLAftPnmkbgEYYjqY3/kCtkvRA3g3QoDwn6nc
qjI3iFSYudyum9CmCMfvPYFfwXJ7uT3s+GPXJj+vLZomFfQm5g9S0/RGLQh2loi+
zCBeCw63y22qqJfNVLx3yVdyEYslu9RcFeuBzWrQ2R+ZYYq1MBdKeNIUqlnbRAvv
gB5jOT5yg5Tzme94Uk2WfTiy5Es2d7KsqlvnKSRuItFI2+LvjfMipV7JLf/5gPE1
1A/A9ALW550kyxVsQtST8wMyTN5ASQ+fyM9MvICgpZa/LBA2hXsO+XCKO0LzOZUg
3ABJVogUpqLwuA6qVAToq4bRNPC7p72odM1tKRHHCNf29r5wtYqu79Eon+3v4Zgf
1wjSJocjJ9yCFxxLMn8PgxcF8Maedp9y/I6dCHEYN5zI6RdwlelUvWcuul6RIEeO
+XORenPq9ZRR8tDO+HSU
=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' into test-merge
ARM: SoC: DT updates for v4.2
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
# gpg: Signature made Wed Jun 24 21:32:14 2015 PDT using RSA key ID D3FBC665
# gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>"
# gpg: aka "Kevin Hilman <khilman@linaro.org>"
# gpg: aka "Kevin Hilman <khilman@kernel.org>"
Combine the ChipIdea USB binding into a single document to reduce
duplication and fragmentation. This marks use of the old PHY bindings as
deprecated. Future compatible bindings should use generic PHY binding.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jqzf
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
twl4030_charger currently finds the associated phy
using usb_get_phy() which will return the first USB2 phy.
If your platform has multiple such phys (as mine does),
this is not reliable (and reliably fails on the GTA04).
Change to use devm_usb_get_phy_by_node(), having found the
node by looking for an appropriately named sibling in
device-tree.
This makes usb-charging dependent on correct device-tree
configuration.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a compatible string to support for R-Car E2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>" in patch 2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some EHCI controllers have a Transaction Translator built into
the root hub. Support this feature in device tree when using
the ehci-platform driver by adding a feature flag for it.
This is needed to get USB working on NXP LPC18xx/43xx platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add documentation for the missing clocks, clock-names, reg and interrupts
properties.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Platforms that have configured DWC_USB3_HSPHY_INTERFACE with
value 3, i.e. UTMI+ and ULPI, need to inform the driver of
the actual HSPHY interface type with the property. "utmi" if
the interface is UTMI+ or "ulpi" if the interface is ULPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a subtle typo phys-names should be phy-names. Using the
current example means you don't have working usb (as you fail to
obtain the phys). Also update the example to use the generic phy
type constants which are now used for miphy28.
Additionally also remove the unnecessary new line in the example.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
VBUS is not routed to USB PHY on recent Qualcomm platforms. USB controller
must see VBUS in order to pull-up DP when setting RS bit. Henc configure
USB PHY and LINK registers sense VBUS and enable manual pullup on D+ line.
Cc: Vamsi Krishna <vskrishn@codeaurora.org>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devicetree changes queued up for v4.1. Here are the highlights:
- Lots of unittest cleanup from Frank Rowand
- Bugfixes and updates to the of_graph code
- Tighten up of_get_mac_address() code
- Documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u6Zy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Here are the devicetree changes queued up for v4.1. Nothing really
exciting here. Rob has another few commits for big-endian attached
UARTs, but those will be sent in a separate merge request since they
haven't been as thoroughly tested as this batch.
Here are the highlights:
- lots of unittest cleanup from Frank Rowand
- bugfixes and updates to the of_graph code
- tighten up of_get_mac_address() code
- documentation updates"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Fix of_platform_depopulate test case
of/unittest: early return from test skips tests
of/unittest: breadcrumbs to reduce pain of future maintainers
of/unittest: reduce checkpatch noise - line after declarations
of/unittest: typo in error string
of/unittest: add const where needed
of_net: factor out repetitive code from of_get_mac_address()
drivers/of: Add empty ranges quirk for PA-Semi
of: Allow selection of OF_DYNAMIC and OF_OVERLAY if OF_UNITTEST
of: Empty node & property flag accessors when !OF
of: Explicitly include linux/types.h in of_graph.h
dt-bindings: brcm: rationalize Broadcom documentation naming
of/unittest: replace 'selftest' with 'unittest'
Documentation: rename of_selftest.txt to of_unittest.txt
Documentation: update the of_selftest.txt
dt: OF_UNITTEST make dependency broken
MAINTAINERS: Pantelis Antoniou device tree overlay maintainer
of: Add of_graph_get_port_by_id function
of: Add for_each_endpoint_of_node helper macro
of: Decrement refcount of previous endpoint in of_graph_get_next_endpoint
This patchset attempts to standardize the naming of dt-bindings
documents based on the Broadcom vendor prefix of brcm.
Although there are no guidelines currently present for how to name
the dt-bindings document the "vendor,binding.txt" style is in use by
some of the other vendors.
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Rob Herring <robh@kernel.org>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
To connect the channel of USB-DMAC to USBHS DnFIFO number, this patch
adds this channel/FIFO number in dma-names. Otherwise, this driver
needs to add analysis code for device tree.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes "Enable USB3 LPM Capability" option from Kconfig
and adds snps,usb3_lpm_capable devicetree property instead of it.
USB3 LPM (Link Power Management) capability is hardware property, and
it's platform dependent, so if our hardware supports this feature, we
want rather to configure it in devicetree than having it as Kconfig option.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
=DrJx
-----END PGP SIGNATURE-----
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bGMq
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Align compatible strings for several IP blocks present on Tegra chips
with the latest doctrine from the DT maintainers:
http://marc.info/?l=devicetree&m=142255654213019&w=2
The primary objective here is to avoid checkpatch warnings, per:
http://marc.info/?l=linux-tegra&m=142201349727836&w=2
DT binding text files have been updated for the following IP blocks:
- PCIe
- SOR
- SoC timers
- AHB "gizmo"
- APB_MISC
- pinmux control
- UART
- PWM
- I2C
- SPI
- RTC
- PMC
- eFuse
- AHCI
- HDA
- XUSB_PADCTRL
- SDHCI
- SOC_THERM
- AHUB
- I2S
- EHCI
- USB PHY
N.B. The nvidia,tegra20-timer compatible string is removed from the
nvidia,tegra30-timer.txt documentation file because it's already
mentioned in the nvidia,tegra20-timer.txt documentation file.
This second version takes into account the following requests from
Rob Herring <robherring2@gmail.com>:
- Per-IP block patches have been combined into a single patch
- Explicit documentation about which compatible strings are actually
matched by the driver has been removed. In its place is implicit
documentation that loosely follows Rob's prescribed format:
"Must contain '"nvidia,<chip>-pcie", "nvidia,tegra20-pcie"' where
<chip> is tegra30, tegra132, ..." [...] "You should attempt to
document known values of <chip> if you use it"
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dylan Reid <dgreid@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-i2c@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-pwm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Three compatible strings have been added to the at91_udc driver.
Update the documentation accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The at91_udc driver request 2 clocks, and thus need them to be defined in
the device tree.
Document the clocks and clock-names properties so that everybody use the
correct names.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Indicate if gadget driver must use dma for usb transfers.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enhance the phy documentation by adding 2 new optional bindings :
- the vbus gpio, which detects usb insertion
- the vbus regulator, which provides current drawn from the usb cable
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
at91sam9rl SoC has an erratum forcing us to toggle the BIAS on USB
suspend/resume events.
This specific handling is only activated when CONFIG_ARCH_AT91SAM9RL is
set and this option is only set when building a non-DT kernel, which is
problematic since non-DT support for at91sam9rl SoC has been removed.
Rework the toggle_bias implementation to attach it to the "at91sam9rl-udc"
compatible string.
Add new compatible strings to avoid executing at91sam9rl erratum handling
on other SoCs.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since bd27fa44e1 ("usb: phy: generic: Don't use regulator framework for
RESET line") we no longer model the reset line as a regulator supply, so
adapt the documentation accordingly.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add device-tree bindings for EHCI so we can use "needs-reset-on-resume"
property to force EHCI reset after resume if necessary. This is necessary
on platforms like rk3288 that need a reset after resume to detect if a
device has been disconnected during suspend time.
Signed-off-by: Wu Liang feng <wulf@rock-chips.com>
Reviewed-by: Julius Werner <jwerner@google.com>
Reviewed-by: Doug Anderson <dianders@google.com>
Reviewed-by: Tomasz Figa <tfiga@google.com>
Reviewed-by: Pawel Osciak <posciak@google.com>
Reviewed-by: Sonny Rao <sonnyrao@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Doug Anderson <dianders@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 controller on Exynos7 SoC has separate control for
AXI UpScaler which connects DWC3 DRD controller to AXI bus.
Get the gate clock for the same to control it across power
cycles.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These quirks are currently set through platform_data; allow DT-based SoCs
to use them too.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch documents the device tree bindings required for
the ohci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for the
ehci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TPL (Targeted Peripheral List) is needed for targets host
(OTG and Embedded Hosts) for usb certification and other
vendor specific requirements.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quite big pull request this time. Audio and UVC gadgets
can now be used with our configfs-based binding. We have
three PHY drivers being removed because a new one has been
added using new PHY framework.
Gadget framework got a new ->reset callback preparing for
some other changes to come on next merge window.
A few new drivers came in as well; among those we have a
new UDC driver from Xilinx and two new glue layers for
DWC3 (ST and Qualcomm).
DWC3 also learned about tracepoints which will help debugging
quite a bit.
Other than that, a big series of non-critical fixes and
cleanups.
All patches have been on linux-next for quite a bit of time
and I boot tested these changes on platforms I have access
to and work with mainline.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VHzN
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.18 merge window
Quite big pull request this time. Audio and UVC gadgets
can now be used with our configfs-based binding. We have
three PHY drivers being removed because a new one has been
added using new PHY framework.
Gadget framework got a new ->reset callback preparing for
some other changes to come on next merge window.
A few new drivers came in as well; among those we have a
new UDC driver from Xilinx and two new glue layers for
DWC3 (ST and Qualcomm).
DWC3 also learned about tracepoints which will help debugging
quite a bit.
Other than that, a big series of non-critical fixes and
cleanups.
All patches have been on linux-next for quite a bit of time
and I boot tested these changes on platforms I have access
to and work with mainline.
Signed-of-by: Felipe Balbi <balbi@ti.com>
QCOM USB3.0 core wrapper consist of USB3.0 IP from Synopsys
(SNPS) and HS, SS PHY's control and configuration registers.
It could operate in device mode (SS, HS, FS) and host
mode (SS, HS, FS, LS).
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Indicate that the generic dr_mode binding should be used for dwc2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This add necessary dwc2 binding documentation for Rockchip socs:
rk3066, rk3188 and rk3288
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the device tree bindings for the Renesas USBHS controller.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch documents the device tree documentation required for
the ST usb3 controller glue layer found in STiH407 devices.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds support for the USB PHY in Vybrid VF610. We assume that
the disconnection without VBUS is also needed for Vybrid.
Tests showed, without MXS_PHY_NEED_IP_FIX, enumeration of devices
behind a USB Hub fails with errors:
[ 215.163507] usb usb1-port1: cannot reset (err = -32)
[ 215.170498] usb usb1-port1: cannot reset (err = -32)
[ 215.185120] usb usb1-port1: cannot reset (err = -32)
[ 215.191345] usb usb1-port1: cannot reset (err = -32)
[ 215.202487] usb usb1-port1: cannot reset (err = -32)
[ 215.207718] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[ 215.219317] usb usb1-port1: unable to enumerate USB device
Hence we also enable the MXS_PHY_NEED_IP_FIX flag.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fsl,usbphy is no optional property. This patch moves it to the list of
required properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Tegra was converted to use the standard reset bindings, the PHY was
forgotten, probably because all the resetting of the USB blocks were
done in the EHCI driver. What also went unnoticed is that resetting the
1st on-chip USB module also wipes some of the UTMI pad configuration
registers that are also used by the other USB blocks. So this fact needs
to be described in the device tree, and the driver modified not to reset
the 1st module at inappropriate times.
In order to stay compatible with old device trees, the USB drivers will
still function without these properties but with the old,
potentially buggy behaviour.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work better
now that it has been reworked to do per-port power control dynamically.
There's also a raft of gadget driver updates and fixes, CONFIG_USB_DEBUG
is finally gone now that everything has been converted over to the
dynamic debug inteface, the last hold-out drivers were cleaned up and
the config option removed. There were also other minor things all
through the drivers/usb/ tree, the shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONYEMACgkQMUfUDdst+ynxvgCggMQBhN5icth8Y5hFglNNaISN
c4AAoMHR2kb62U1plylLbPnboQTjfcl0
=fG6y
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next
Pull USB driver updates from Greg KH:
"Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work
better now that it has been reworked to do per-port power control
dynamically. There's also a raft of gadget driver updates and fixes,
CONFIG_USB_DEBUG is finally gone now that everything has been
converted over to the dynamic debug inteface, the last hold-out
drivers were cleaned up and the config option removed. There were
also other minor things all through the drivers/usb/ tree, the
shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms"
* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
USB: orinoco_usb: remove CONFIG_USB_DEBUG support
USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
USB: media: streamzap: remove CONFIG_USB_DEBUG
USB: media: redrat3: remove CONFIG_USB_DEBUG usage
USB: media: redrat3: remove unneeded tracing macro
usb: qcserial: add additional Sierra Wireless QMI devices
usb: host: max3421-hcd: Use module_spi_driver
usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
usb: qcserial: add Netgear AirCard 341U
Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
usb: host: xhci-plat: add xhci_plat_start()
usb: host: max3421-hcd: Fix potential NULL urb dereference
Revert "usb: gadget: net2280: Add support for PLX USB338X"
USB: usbip: remove CONFIG_USB_DEBUG reference
USB: remove CONFIG_USB_DEBUG from defconfig files
usb: resume child device when port is powered on
usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
...
This commit extends the compatible string list of the xhci-platform
binding with the new "renesas,xhci-r8a7790" and "renesas,xhci-r8a7791"
compatible strings. It is used to describe the xHCI controller which
is available in the R-Car H2 and M2 SoCs.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"7408484 usb: gadget: s3c-hsotg: enable generic phy support" introduces
generic phy support to the dwc2.txt binding and the s3c-hsotg driver
which implements support for the binding. The binding documentation
incorrectly states that the phy-names property will be "device". The
binding example, driver, and one dts user all implement the phy-names
property as requiring "usb2-phy".
Fix the dwc2.txt binding documentation to correctly specify "usb2-phy"
as the appropriate value for phy-names.
Reported-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
USB3503 chip supports 8 values of reference clock. The value is
specified by REF_SEL[1:0] pins and INT_N line. This patch add support
for getting 'refclk' clock, enabling it and setting INT_N line according
to the value of the gathered clock. If no clock has been specified,
driver defaults to the old behaviour (assuming that clock has been
specified by REF_SEL pins from primary reference clock frequencies
table).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Allwinner's A31 SoC the reset line connected to the EHCI IP has to
be deasserted for the EHCI block to be usable.
Add support for an optional reset controller that will be deasserted on
power off and asserted on power on.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OHCI controllers used in the Allwinner A31 are asserted in reset using a
global reset controller.
Add optional support for such a controller in the OHCI platform driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit extends the compatible string list of the xhci-platform
binding with the new "armada-375-xhci" and "armada-380-xhci"
compatible strings. It is used to describe the XHCI controller which
is available in the Armada 375 and 38x SoCs.
It also indicates that an optional 'clocks' property is now supported.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit updates the Device Tree binding documentation of
ehci-orion to take into account the fact that we can now optionally
pass a clock and a PHY reference.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the phy provider, supplied by new Exynos-usb2phy using
Generic phy framework.
Keeping the support for older USB phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ehci-exynos.
Once we move to new phy in the device nodes for ehci, we can
remove the support for older phys.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Addressed review comments from mailing list]
[gautam.vivek@samsung.com: Kept the code for old usb-phy, and just
added support for new exynos5-usb2phy in generic phy framework]
[gautam.vivek@samsung.com: Edited the commit message]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to consume phy provided by Generic phy framework.
Keeping the support for older usb-phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ohci-exynos.
Once we move to new phy in the device nodes for ohci, we can
remove the support for older phys.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document device tree binding information as required by
the Qualcomm USB controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the compatible "ti,am437x-dwc3" for dwc3 glue driver.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New platform uses RBCPR hardware feature, with that voting for
absolute voltage of VDD CX is not required. Hence vote for corner of
VDD CX which uses nominal corner voltage on VDD CX.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow support to use 2nd HSPHY with USB2 Core.
Some platforms may have configuration to allow USB controller
work with any of the two HSPHYs present. By default driver
configures USB core to use primary HSPHY. Add support to allow
user select 2nd HSPHY using DT parameter.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Provide more information on the two different interrupt cases and more
information of endpoint buffer sizes. Suggested by Mark Rutland.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
Missing bindings were found on running checkpatch.pl on bsc9132
device tree. This patch add/update the following
- Add bindings for L2 cache controller
- Add bindings for memory controller
- Update bindings for USB controller
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
atmel,at91sam9rl-udc is a USB gadget, it has no means to control vbus.
atmel,vbus-gpio is in fact used to detect the presence of vbus.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: modify the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Richard Leitner