The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for A64
This reverts commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fill ESPRESSObin uart0 node with pinctrl information like in the
Armada-3720-DB device tree (which uses the same node).
Also explain how to enable the second UART port available on the
headers. This second port is not enabled by default because both
headers are dedicated to expose general purpose pins and remapping
some of them to use the second UART would break existing users.
Suggested-by: László ÁSHIN <laszlo@ashin.hu>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable Armada-3720-DB second UART port by adding the corresponding
device tree node in the board DTS and enabling it.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a node in Armada 37xx DTSI file for the second UART, with a
different compatible due to its extended IP which has some
differences with the first UART already in place.
Make use of this commit to also fully describe the first port and
use the same clear and named interrupt bindings for both ports.
The standard UART (UART0) uses level-interrupts while the extended
UART (UART1) uses edge-triggered interrupts.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the missing clock property to armada-3700 UART node.
This clock will be used to derive the prescaler value to comply with
the requested baudrate.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- add support for new GPIO IRQ driver
-----BEGIN PGP SIGNATURE-----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=vVV3
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.15, round 2" from Kevin Hilman:
- add support for new GPIO IRQ driver
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: add external PHY interrupt on some platforms
ARM64: dts: meson-gx: add gpio interrupt controller
ARM64: meson: enable MESON_IRQ_GPIO in Kconfig
ARM64: dts: meson-gxbb-odroidc2: fix usb1 power supply
- Add GICv3 ITS node and PCIe devcies for LS1088A support.
- Enable PCIe support for LS2088A SoC.
- Add OP-TEE support for various Layerscape SoCs, LS1012A, LS1043A,
LS1046A, LS1088A and LS208XA.
- Update DPAA QBMan nodes to use constant defines in the interrupt
description.
- Add DSPI device to support SPI-NOR on LS1012A based boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ7y0kAAoJEFBXWFqHsHzOE70H/iAI1WmTWW1kuc2d7w1pCZrP
m3aBdavPb6N2XT43HUDo5yuAVl84AvmoHWkOXeiAEgSTwuGCMcAT90P3v+MJQG5P
xFCuqEAYfKb4BwMNs3oBbgdWBErxOpqFGd58vvXbEHzGv6DCnJRD6euhVNMosTKv
QI62vZkbD3sR1aUcC/dLG0hCFRb7+fscL+sgtU0vnF5nWKQLXQ/eGCDhhh4mmY/5
sjgeCqhYeIBrhpoOLm8qK9CkRnf7nPZwSiTFhG1o0nHDqbmzTRU5zQrAEDGB9Ukg
pWDtHyIEkrmnzOucIbKVpFue7IldkR7WN2rslpkHhtDaK1gIYnhjO26toU7/f2U=
=T0d9
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "Freescale arm64 device tree updates for 4.15" from Shawn Guo:
- Add GICv3 ITS node and PCIe devcies for LS1088A support.
- Enable PCIe support for LS2088A SoC.
- Add OP-TEE support for various Layerscape SoCs, LS1012A, LS1043A,
LS1046A, LS1088A and LS208XA.
- Update DPAA QBMan nodes to use constant defines in the interrupt
description.
- Add DSPI device to support SPI-NOR on LS1012A based boards.
* tag 'imx-dt64-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: update the DPAA QBMan nodes
arm64: dts: ls1088a: add PCIe controller DT nodes
arm64: dts: ls1088a: add gicv3 ITS DT node
arm64: dts: ls2088a: add pcie support
arm64: dts: ls: Add optee node
dt-bindings: mtd: add sst25wf040b and en25s64 to sip-nor list
dt-bindings: spi: Add fsl,ls1012a-dspi compatible string
arm64: dts: ls1012a: add the DTS node for DSPI support
On Armada 7K/8k:
- Improve network support at SoC and board level
- Enable watchdog
- Add UART muxing
- On 7040 DB: add CD SDIO and NAND support
- On 8040 DB: add PCIE more ports and SPI1
On Armada 37xx:
- Fix UART register size
- Add vmmc regulator for SD on 3720 DB
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWeoPnCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71eWeAJ4yqhFToGh9
bLvyANmN33Lp0kYfEwCeKTJv715mvxAfJMYUMX7CUmgEAOs=
=9sls
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.15-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.15 (part 1)" from Gregory CLEMENT:
On Armada 7K/8k:
- Improve network support at SoC and board level
- Enable watchdog
- Add UART muxing
- On 7040 DB: add CD SDIO and NAND support
- On 8040 DB: add PCIE more ports and SPI1
On Armada 37xx:
- Fix UART register size
- Add vmmc regulator for SD on 3720 DB
* tag 'mvebu-dt64-4.15-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: 7040-db: Add the carrier detect pin for SD card on CP
arm64: dts: marvell: 7040-db: Document the gpio expander
arm64: dts: marvell: enable additional PCIe ports on Armada 8040 DB
arm64: dts: marvell: add NAND support on the 7040-DB board
arm64: dts: marvell: Enable Armada-8040-DB CPS SPI1
arm64: dts: marvell: 8040-db: enable the SFP ports
arm64: dts: marvell: 7040-db: enable the SFP port
arm64: dts: marvell: 7040-db: add comphy reference to Ethernet port
arm64: dts: marvell: mcbin: add comphy references to Ethernet ports
arm64: dts: marvell: 37xx: remove empty line
arm64: dts: marvell: cp110: add PPv2 port interrupts
arm64: dts: marvell: add comphy nodes on cp110 master and slave
arm64: dts: marvell: extend the cp110 syscon register area length
arm64: dts: marvell: enable AP806 watchdog
arm64: dts: marvell: Fix A37xx UART0 register size
arm64: dts: marvell: armada-3720-db: Add vmmc regulator for SD slot
arm64: dts: marvell: add UART muxing on Armada 7K/8K
* r8a7795 (H3) and r8a7796 (M3-W) SoCs
- Use R-Car Gen 3 fallback compat string for GPIO
Simon Horman says "Use newly added R-Car GPIO Gen 1, 2 and 3 fallback
compat strings in peace of now deprecated non-generation specific R-Car
GPIO fallback compat string in the DT of Renesas ARM and arm64 based
SoCs.
* r8a7795 (H3) and r8a7796 (M3-W) Salvator boards
- Add dr_mode property for USB2.0 channel 0
Shimoda-san says "Since Salvator-X[S] have a USB2.0 dual-role channel
(CN9), this patch
adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Using dual-role channel (or not) is related to the type of USB receptor
on board specification. So, I added the property into the
salvator-common.dtsi."
- Add pfc node for USB3.0 channel 0
Shimoda-san says "Since a R-Car Gen3 bootloader enables the PFC of
USB3.0 channel 0, the USB3.0 host controller works without this setting
on the kernel. But, this setting should have salvator-common.dtsi. So,
this patch adds the pfc node for USB3.0 channel 0."
* r8a7795 (H3) and r8a7796 (M3-W) Salvator and ULCB boards
- Correct audio_clkout
Morimoto-san says ""audio_clkout" is dummy clock of <&rcar_sound 0> to
avoid clock loop which invites probe conflct. Thus <&rcar_sound 0> and
"audio_clkout" should be same value."
* r8a7795 (H3) and r8a7796 (M3-W) Salvator and ULCB, and
r8a77995 (D3) Draak boards
- Drop "avb_phy_int" from avb_pins
Shimoda-san says "Since the Ethernet AVB driver doesn't support
AVB_PHY_INT handling and it will be handled by a phy driver as a gpio
pin, this patch removes the "avb_phy_int" from the avb_pins node."
* r8a77995 (D3) Draak board
- Enable PWM channels
Shimoda-san says "Each channel connects to LTC2644 for brightness
control."
* r8a77970 (V3M) Eagle and ULCB Kingfisher boards
- Add initial device tree support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAlnpzqwACgkQ189kaWo3
T75X7w//Xf29SJUGRAZ8fYnA5b8r+QHvJX/79eI5Z+Nq12UGdPZXS6yhBsfcptD4
EGY9E6u7O+wJryhZJT50t7Dr19WzGgLDfsqBas9wXxaniAh7sLn4fIvcrwrDf86a
LJT9JWinjEbOqO4Crc4GEx4i2r/kZVIwL0HOA5o64JclW33NwCAzo7D/Z3uDBrXa
H16G8webhjCLa4vhdqPmYJO9OlKwtnLcx6XA855do2uUbRF1O7chekyOXFKccOk+
FvBH96hH7dEBmE9GwrjTiiFOfIDyU7kzDVKwz+UurUC+zrqfc8N12OdttodrN8+i
iOMGVOMxbAE1eYbvTkxCT7OB0r2GYnFqb5JkNT/3PiEstf3YrxGm15drZYf10d/E
mgv6ifKgq02cTVjQF3JF7jAcMaHbB18dde86fe5DspAH32SyFzGnUc8I3LwLWScf
pxIPSycI5rrPwKYbITCPOLbem3nS1PPvOB/r6B+6E/wyrU7OOe0YCr4GsJLhzhrH
IPNNt0DZa+K7crWbqQetv4+s8Jf61nXp2iUjuKP64k+YDKkM5CcPSsF6PnbiRjXn
Rt8k2wpNS72Cvq/D+zs9l8ymX1Z7goe66fmYDfCxpd4SehyYL2QAxL6K2eOCOv1C
MZtbJ18zyUXmsNZvVd/dW4g6W5zOn/l9VpD9oxREo5bFXR7nR/Q=
=BmC8
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM64 Based SoC DT Updates for v4.15" from Simon Horman:
* r8a7795 (H3) and r8a7796 (M3-W) SoCs
- Use R-Car Gen 3 fallback compat string for GPIO
Simon Horman says "Use newly added R-Car GPIO Gen 1, 2 and 3 fallback
compat strings in peace of now deprecated non-generation specific R-Car
GPIO fallback compat string in the DT of Renesas ARM and arm64 based
SoCs.
* r8a7795 (H3) and r8a7796 (M3-W) Salvator boards
- Add dr_mode property for USB2.0 channel 0
Shimoda-san says "Since Salvator-X[S] have a USB2.0 dual-role channel
(CN9), this patch
adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Using dual-role channel (or not) is related to the type of USB receptor
on board specification. So, I added the property into the
salvator-common.dtsi."
- Add pfc node for USB3.0 channel 0
Shimoda-san says "Since a R-Car Gen3 bootloader enables the PFC of
USB3.0 channel 0, the USB3.0 host controller works without this setting
on the kernel. But, this setting should have salvator-common.dtsi. So,
this patch adds the pfc node for USB3.0 channel 0."
* r8a7795 (H3) and r8a7796 (M3-W) Salvator and ULCB boards
- Correct audio_clkout
Morimoto-san says ""audio_clkout" is dummy clock of <&rcar_sound 0> to
avoid clock loop which invites probe conflct. Thus <&rcar_sound 0> and
"audio_clkout" should be same value."
* r8a7795 (H3) and r8a7796 (M3-W) Salvator and ULCB, and
r8a77995 (D3) Draak boards
- Drop "avb_phy_int" from avb_pins
Shimoda-san says "Since the Ethernet AVB driver doesn't support
AVB_PHY_INT handling and it will be handled by a phy driver as a gpio
pin, this patch removes the "avb_phy_int" from the avb_pins node."
* r8a77995 (D3) Draak board
- Enable PWM channels
Shimoda-san says "Each channel connects to LTC2644 for brightness
control."
* r8a77970 (V3M) Eagle and ULCB Kingfisher boards
- Add initial device tree support
* tag 'renesas-arm64-dt2-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
arm64: dts: renesas: salvator-common: add dr_mode property for USB2.0 channel 0
arm64: dts: r8a7796: Use R-Car GPIO Gen3 fallback compat string
arm64: dts: r8a7795: Use R-Car GPIO Gen3 fallback compat string
arm64: renesas: ulcb: fixup audio_clkout
arm64: renesas: salvator-common: fixup audio_clkout
arm64: dts: renesas: eagle: add EtherAVB support
arm64: dts: r8a77995: Add INTC-EX device node
arm64: dts: r8a77970: Add INTC-EX device node
arm64: dts: r8a7796: Add INTC-EX device node
arm64: dts: ulcb-kf: hog USB3 hub control gpios
arm64: dts: ulcb-kf: enable PCA9548 on I2C4
arm64: dts: ulcb-kf: enable PCA9548 on I2C2
arm64: dts: ulcb-kf: enable TCA9539 on I2C4
arm64: dts: ulcb-kf: enable TCA9539 on I2C2
arm64: dts: ulcb-kf: enable USB3.0 Host
arm64: dts: ulcb-kf: enable PCIE0/1
arm64: dts: ulcb-kf: enable USB2.0 Host channel 0
arm64: dts: ulcb-kf: enable HSUSB
arm64: dts: ulcb-kf: enable CAN0/1
arm64: dts: ulcb-kf: enable SCIF1
...
Most notable changes:
- SPI and DMA support on the a64
- New boards: NanoPi NEO Plus2
-----BEGIN PGP SIGNATURE-----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=OAav
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner arm64 DT changes for 4.15" from Maxime Ripard:
Most notable changes:
- SPI and DMA support on the a64
- New boards: NanoPi NEO Plus2
* tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: allwinner: Correct unit name in devicetree binding example
arm64: allwinner: a64: add dma controller references to spi nodes
arm64: allwinner: a64: Add device node for DMA controller
arm64: allwinner: a64: Fix node with unit name and no reg property
arm64: allwinner: a64: Fix simple-bus unit address format error
arm64: allwinner: h5: add NanoPi NEO Plus2 DT support
arm64: allwinner: a64: add SPI nodes
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
-----BEGIN PGP SIGNATURE-----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=HjP6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15" from Maxime Ripard:
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
- New R40 SoC support
* tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (63 commits)
ARM: sun8i: r40: enable USB host for Banana Pi M2 Ultra
ARM: sun8i: v40: add 5V regulator for Banana Pi M2 Berry
ARM: sun8i: r40: add 5V regulator for Banana Pi M2 Ultra
ARM: sun8i: r40: add USB host port nodes for R40
ARM: dts: sun4i: Enable HDMI support on some A10 devices
ARM: dts: sun7i: Enable HDMI support on some A20 devices
ARM: dts: sun7i: Add device nodes for display pipelines
ARM: dts: sun4i: Add device nodes for display pipelines
ARM: dts: sun8i: r40: add watchdog device node
ARM: dts: sun5i: reference-design-tablet: Enable AXP209 AC and battery
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun4i: Remove underscores from nodes names
ARM: dts: sun4i: Provide default muxing for relevant controllers
ARM: dts: sun4i: Change pinctrl nodes to avoid warning
ARM: dts: sun6i: Enable HDMI support on some A31/A31s devices
ARM: dts: sun6i: Add device node for HDMI controller
ARM: dts: sun4i: Change LRADC node names to avoid warnings
ARM: dts: sun4i: Remove skeleton and memory to avoid warnings
ARM: dts: sun4i: Remove gpio-keys warnings
...
Add the external PHY interrupt on the nanopi-k2, odroid-c2, p200, p230
and q200
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Looking at the schematics, the USB Power Supply is shared between the
two USB interfaces,
If the usb0 fails to initialize, the second one won't have power.
Fixes: 5a0803bd5a ("ARM64: dts: meson-gxbb-odroidc2: Enable USB Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the definition for eFuse that is found on RK3368 SoCs with the
corresponding data cells.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Interrupt lines from on-board devices are connected to the GPIO
controller. Add GPIO hogging so that the corresponding GPIO line
is automatically requested.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Interrupt lines from on-board devices are connected to the GPIO
controller. Handle this correctly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The GPIO controller also acts as an interrupt controller and the
interrupt lines are connected to the AIDET block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix warnings like follows:
Warning (node_name_chars_strict): Character '_' not recommended in ...
Commit 8654cb8d03 ("dtc: update warning settings for new bus and
node/property name checks") says these checks are a bit subjective,
but Rob also says to not add new W=2 warnings.
The exising warnings should be fixed in order to catch new ones
easily.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add efuse node for UniPhier LD11, LD20, and PXs3.
This efuse node is included in soc-glue.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Two fixes, one for the A31 DRM binding, and one for a missing regulator on
the pine MMC controller.
-----BEGIN PGP SIGNATURE-----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=Cvge
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.14" from Maxime Ripard:
Two fixes, one for the A31 DRM binding, and one for a missing regulator on
the pine MMC controller.
* tag 'sunxi-fixes-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0
Without the STDMAC clock enabled, the USB 2.0 hosts do not work.
This clock must be explicitly listed in the "clocks" property because
it is independent of the other clocks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since Salvator-X[S] have a USB2.0 dual-role channel (CN9), this patch
adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull "Rockchip dts64 updates for 4.15 part1" from Heiko Stübner:
The biggest step forward is probably the enablement of display support
on the rk3399-firefly, which got its default serial set as well and
got cec support as well.
Gru boards got their touchpad support refined to actually mark the button
correctly and also git their rt5514 dsp added.
And finally the rk3328 eval board got its cpu regulator and mmc nodes.
* tag 'v4.15-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: enable cec pin for rk3399 firefly
arm64: dts: rockchip: add the cec clk for dw-mipi-hdmi on rk3399
arm64: dts: rockchip: default serial for Firefly-RK3399
arm64: dts: rockchip: enable touchpad button for rk3399-gru-kevin
arm64: dts: rockchip: enable display subsystem on rk3399-firefly
arm64: dts: rockchip: Add rt5514 dsp for rk3399 gru
arm64: dts: rockchip: add cpu regulator for rk3328 evaluation board
arm64: dts: rockchip: add mmc nodes for rk3328 evaluation board
Pull "Qualcomm ARM64 Updates for v4.15" from Andy Gross:
* Add PCIE support to relevant MSM8996 based boards
* Add RPM clock controller node on MSM8996
* Add dload address on MSM8916 and MSM8996
* Add MBHC button support on APQ8016 SBC
* Add RTMFS specific compatible for rmtfs memory node
* Fixups for MSM8916 GPIO line names and MDP address length
* tag 'qcom-arm64-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: msm8916: Mark rmtfs node as qcom, rmtfs-mem compatible
arm64: dts: msm8996: Add the rpm clock controller node
arm64: dts: qcom: sbc: Name GPIO lines
arm64: dts: qcom: msm8916: Shrink mdp address length for msm8916
arm64: dts: apq8016-sbc: add mbhc buttons support
arm64: dts: qcom: Specify dload address for msm8916 and msm8996
arm64: dts: apq8096-db820c: never disable regulator on LS expansion
arm64: dts: apq8096-db820c: Enable on board 3 pcie root complex
arm64: dts: qcom: msm8996: add support to pcie
ARM64: DT: Hisilicon SoC DT updates for 4.15
- Add CoreSight related nodes for hi6220
- Add GPIO line names for hikey960
- Rectify the GPIO line names of the Poplar board to keep consistency
- Add thermal sensor binding doc and dt nodes for hi3660
* tag 'hisi-arm64-dt-for-4.15' of git://github.com/hisilicon/linux-hisi:
arm64: dts: Register Hi3660's thermal sensor
dt-bindings: Document the hi3660 thermal sensor binding
arm64: dts: hisilicon: Standardize Poplar GPIO line names
arm64: dts: hikey960: Update HiKey960 with GPIO line names
arm64: dts: hi6220: add coresight dt nodes
Pull "ARMv8 Vexpress/Juno DT update for v4.15" from Sudeep Holla:
Just single update to enable PSCI support on Foundation models
* tag 'juno-updates-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: foundation-v8: Enable PSCI mode
Pull "SoCFPGA DTS updates for v4.15" from Dinh Nguyen:
- Stratix10 platform updates
- Fix up gic register entry
- Enable ethernet/SDMMC
- Update reset manager properties
* tag 'socfpga_dts_for_v4.15_part1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: stratix10: add reset property for various peripherals
arm64: dts: stratix10: add the 'altr,modrst-off' property
arm64: dts: stratix10: include the reset manager bindings
arm64: dts: stratix10: add ethernet/sdmmc support to the S10 devkit
arm64: dts: stratix10: fix up the gic register for the Stratix10 platform
Pull "Renesas ARM64 Based SoC DT Updates for v4.15" from Simon Horman:
* r8a7795 (H3)
- Use r8a7795-cpg-mssr and r8a7795-sysc bindings
Hardcoded indicies are replaced with symbols now that they are available
- Drop bogus HDMI node name suffixes
Laurent Pinchart says: Node names should not use numerical suffixes if
the nodes can be distinguished by unit-address
- Update PFC node name to pin-controller
Shimoda-san says the PFC node name is changed "from e6060000.pfc and
pfc@e6060000 to e6060000.pin-controller and pin-controller@e6060000
like other Renesas SoCs."
* r8a7795 (H3) ES1.0
- Drop extra zero from XHCI unit address
This corrects a typo were ee0400000 rather than ee040000 was used
as the unit address.
* r8a7796 (M3-W)
- Add FDP1 instance
Laurent Pinchart says: The r8a7796 has a single FDP1 instance.
* r8a7795 (H3) and r8a7796 (M3-W) SoCs
- Add USB3.0 peripheral device nodes
Shimoda-san says that this is not enabled on the Salvator-X/XS boards
for now as:
+ we need a special cable (USB type-A to A cross cable).
+ we can swap the role by renesas_usb3 driver even if we use a normal
cable and after usb3.0 host is running, but I think it's a special
use case.
* r8a7795 (H3) and r8a7796 (M3-W) ULCB boards
- Enable display output
Laurent Pinchart says: The DU is already wired up to the HDMI encoder,
all we need to do is enable it.
* r8a77995 (D3) Draak board
- Enable EthernetAVB and , USB2.0 Host and PHY
- Add serial console pins.
This is safe to do now that r8a77995 PFC driver support is present
* r8a77970 (V3M)
- Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes
This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC
in the Eagle board support for which is under review
* tag 'renesas-arm64-dt-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node
arm64: dts: renesas: r8a7795: add USB3.0 peripheral device node
arm64: dts: renesas: r8a77995: draak: enable EthernetAVB
arm64: dts: renesas: r8a77995: draak: enable USB2.0 Host (EHCI/OHCI)
arm64: dts: renesas: r8a77995: draak: enable USB2.0 PHY
arm64: dts: renesas: r8a77995: add USB2.0 Host (EHCI/OHCI) device node
arm64: dts: renesas: r8a77995: Add USB2.0 PHY device node
arm64: dts: draak: Add serial console pins
arm64: dts: renesas: r8a77970: add EtherAVB support
arm64: dts: renesas: r8a77970: add [H]SCIF support
arm64: dts: renesas: r8a77970: add SYS-DMAC support
arm64: dts: renesas: initial R8A77970 SoC device tree
arm64: dts: renesas: r8a77995: Add EthernetAVB device node
arm64: dts: renesas: r8a77995: add GPIO device nodes
arm64: dts: renesas: r8a77995: Use r8a7795-cpg-mssr binding definitions
arm64: dts: renesas: r8a77995: Use r8a7795-sysc binding definitions
arm64: renesas: Add Renesas R8A77970 Kconfig support
arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes
arm64: dts: renesas: ulcb: Enable display output
arm64: dts: renesas: r8a77995: update PFC node name to pin-controller
...
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot/dts -type -f -name '*.dts*'
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add 12V regulator to backlight allowing the power supply
for the backlight to be found.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZyLGhAAoJENfPZGlqN0++U5oQAKjIikenaz1ZlG25+cWCgkxa
E+PMqSH49eUpHqtJlHC0nRF4H9terzMMLHYQPL1SZME8j56x5bjGI80OtnBKdD0V
GxXrpPv9ekl5vBBroQM6/1ZS9v1aFWjlNzpV1jC+TQwtTEo2xzr4+DJ+z4vllyps
bptOIn3ix/NuNSl5P146buSOKBumSB4advGh9emzrsGc41RUCgfaGZmIlyvmkorf
3vW/NW9fBk+bauZT2AH1gYEsxlCMPBr6EmUJAiSLAAuEXf8SsSs16ls6E5sGEEhO
AhuKh3lfK3TZNEGiC2pDv2WNqQyr+gNM2mDRnwcIXqDpvXYtFPUHN3EcSpf+stXa
yrJMro9BJeKmzHj7jReArxMOJsLF8KIx6udUobJ1hKAxGQJlxopJmhldGXBarMV1
enGhp7qGSVf5VpMf2iNJo6pU6MNRB3dnel+3LtwhwG0Uxu8Y2dsWcrwxSFipmlnJ
nAsoC3cuewHuPHCYGvyRoQ6RtKcdJ1XVcMg9nYvbQVkyBUl8o+Y/4Ock17jpG5ro
a+F8XBowk4q1INm3QQHIqSqi7G4K01Tnhw95hcudbJwc26wtGY79CqifiKmnOq6+
MRAG0UvtMUOVgD++vSE5vTg/f8lfRFYUu+aCCzTjEzUs1/rawXyk8I4nEqZjZx3Q
n0U8qQGkOeZ1jUpktZz3
=zIL3
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.14" from Simon Horman:
Add 12V regulator to backlight allowing the power supply
for the backlight to be found.
* tag 'renesas-fixes-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: salvator-common: add 12V regulator to backlight
exceed 3.0V, so they got fixed to not be at 3.3V
And Arnd found a typo in the recently added iommu nodes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlnmSIIQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeaQB/9JDBD545VzXqsNixEnJOcT+X8sUZpu6OmT
j3v5kJDPOXLfSP/Ci9S10ldix/JUBZoT2fRJCK5QAzo+NnjYWrC5qPAwGVU90TqY
KxFZu4f1763AU2ZLw9nGJlFeVHrjhpFdYfe9GpPPLmndjM32cRdGCRI5zDaSB7s8
popUs6qNGvI5Q770x4/xTfEqDlfdQhmYyNfWumji7ACfLTHYZnpyq0SN/o4qp/rg
UJaPx/7PGzHIDSrEKRE3i+waG3d7Ix4th9jkmrYFAK2nIiySlZg9WIKWEOqqt+sf
H8W3ygdlaYZlzIPJhY2r6/W1rQoJSLxxKColLrV32hDkjPfcFon5
=YPhS
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 Fixes for 4.14 part 2" from Heiko Stübner:
The vqmmc voltages on rk3399 pose a risk for the chip if they
exceed 3.0V, so they got fixed to not be at 3.3V
And Arnd found a typo in the recently added iommu nodes.
* tag 'v4.14-rockchip-dts64fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: fix typo in iommu nodes
arm64: dts: rockchip: correct vqmmc voltage for rk3399 platforms
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWeDbriMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71RAJAJ9TyT+GrMdf
HsM7V74bSWYAUlWZ0ACcCWjIdnbVlinP+iuVS462du4HpU0=
=2AQR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fixes for 4.14 (part 2)" from Gregory CLEMENT
Two device tree related fixes:
- One on Armada 38x using a other compatible string for I2C in order
to cover an errata.
- One for Armada 7K/8K fixing a typo on interrupt-map property for
PCIe leading to fail PME and AER root port service initialization
And the last one for the mbus fixing the window size calculation when
it exceed 32bits
* tag 'mvebu-fixes-4.14-2' of git://git.infradead.org/linux-mvebu:
bus: mbus: fix window size calculation for 4GB windows
ARM: dts: Fix I2C repeated start issue on Armada-38x
arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
This adds the thermal sensor device provided by the BPMP, and the
relevant thermal sensors to the Tegra186 device tree.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has three PCIe controllers, which can be operated
in 401, 211 or 111 lane combinations. Add DT support for
PCIe controllers.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a node for the Video Image Compositor on the Tegra186.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the node for Host1x on the Tegra186, without any subdevices
for now.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add #power-domain-cells for the BPMP node on Tegra186 so that the power
domain provider may be used.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Try to add basic DT support for the Amlogic's Meson-AXG A113D SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The latest dtc warns about an extraneous cell in the interrupt
property of two of the iommu device nodes:
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff373f00
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff900800
This removes the typo.
Fixes: cede4c79de ("arm64: dts: rockchip: add rk3368 iommu nodes")
Fixes: 49c82f2b7c ("arm64: dts: rockchip: add rk3328 iommu nodes")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The vcc_sd or vcc_sdio used for IO voltage for sdmmc and sdio
interface on rk3399 platform have a limitation that it can't be
larger than 3.0v, otherwise it has a potential risk for the chip.
Correct all of them.
Fixes: 171582e00d ("arm64: dts: rockchip: add support for firefly-rk3399 board")
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Fixes: 8164a84cca ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use newly added R-Car GPIO Gen3 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7796 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use newly added R-Car GPIO Gen3 fallback compat string
in place of now deprecated non-generation specific
R-Car GPIO fallback compat string in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
"audio_clkout" is dummy clock of <&rcar_sound 0> to avoid clock loop
which invites probe conflict. Thus <&rcar_sound 0> and "audio_clkout"
should be same value.
On commit 2752660a37 ("arm64: dts: renesas: ulcb: sound
clock-frequency needs descending order") exchanged <&rcar_sound 0>,
but it didn't modify "audio_clkout".
This patch fixup it.
Fixes: 2752660a37 ("arm64: dts: renesas: ulcb: sound clock-frequency needs descending order")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
"audio_clkout" is dummy clock of <&rcar_sound 0> to avoid clock loop
which invites probe conflict. Thus <&rcar_sound 0> and "audio_clkout"
should be same value.
On commit 5e2feac330 ("arm64: renesas: salvator-common: sound
clock-frequency needs descending order") exchanged <&rcar_sound 0>,
but it didn't modify "audio_clkout".
This patch fixup it.
Fixes: 5e2feac330 ("arm64: renesas: salvator-common: sound clock-frequency needs descending order")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a Device Tree for the PROBOX2 AVA TV Box.
Move common memory reservations into rtd1295.dtsi.
Cc: support@probox2.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add a pinctrl setting to configure the cec pin to the correct function.
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the HDMI CEC controller main clock coming from the CRU.
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add nodes of thermal monitor and thermal zone for UniPhier LD20 SoC.
The thermal monitor node is included in sysctrl. Since the efuse might not
have a calibrated value of thermal monitor, this patch gives the default
value for LD20.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Firefly-RK3399 uses serial2 with 1,500,000 baud by default
for communication in U-Boot and in the vendor provided distros.
So let us set the same default in the Linux kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adding the linux,gpio-keymap entry also has
the side-effect of making the driver register
the touchpad as a touchpad rather than another
touchscreen.
The index for BTN_LEFT was found by trial and error.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SD card slot connected to the SD controller of the CP part has a
carrier detect pin connected the gpio expander. This patch enables it
allowing supporting the hotplug event for the SD card.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that we have a binding defined for the shared file system memory use
this to describe the rmtfs memory region.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This names the GPIO lines on the APQ8016 "SBC" also known
as the DragonBoard 410c, according to the schematic. This
is necessary for a conforming userspace looking across
all GPIO chips for the GPIO lines named "GPIO-A" thru
"GPIO-L".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This shrinks the address size down to 89000 from its previous 90000
which was mistakenly pulled from downstream.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
On msm8916 and msm8996 boards a secure io-write is used to write the
magic for selecting "download mode", specify this address in the
DeviceTree.
Note that qcom_scm.download_mode=1 must be specified on the kernel
command line for the kernel to attempt selecting download mode.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
1.8v regulator on LS expansion should not be disabled anytime to comply
with 96boards spec. So make this explicit with always-on flag.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since the switch to documented uart bindings, the old undocumented
compatible binding was left for simplicity.
This patch removes these unneeded compatible strings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the switch to documented uart bindings, the clocks are
redefined in the SoC family dtsi file.
This patch removes these unneeded properties.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This year, Amlogic updated the ARM Trusted Firmware reserved memory mapping
for Meson GXL SoCs and products sold since May 2017 uses this alternate
reserved memory mapping.
But products had been sold using the previous mapping.
This issue has been explained in [1] and a dynamic solution is yet to be
found to avoid loosing another 3Mbytes of reservable memory.
In the meantime, this patch adds this alternate memory zone only for
the GXL and GXM SoCs since GXBB based new products stopped earlier.
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
Fixes: bba8e3f427 ("ARM64: dts: meson-gx: Add firmware reserved memory zones")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable HS400 high speed eMMC mode on the khadas vim2
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable both gxbb USB controllers and add a 5V regulator for the OTG port
VBUS, similar to p20x.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Tronsmart Vega S96 is a TV box derived from Amlogic q200 reference design.
Cc: support@tronsmart.com
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM2 is a Single Board Computer, respin of the origin
Khadas VIM board, using an Amlogic S912 SoC and more server oriented.
It provides the same external connectors and header pinout, plus a SPI
NOR Flash, a reprogrammable STM8S003 MCU, FPC Connector, Cooling FAN header
and Pogo Pads Arrays.
Cc: Gouwa <gouwa@szwesion.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
TEST_N gpio has been moved so the gpio-line-names of the cc
must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
TEST_N gpio has been moved so the gpio-line-names of the kvim
must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
GPIOX22 is now declared properly and TEST_N has been moved so
the gpio-line-names of the odroid-c2 must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
GPIOX22 is now declared properly and TEST_N has been moved so
the gpio-line-names of the nanopi-k2 must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
TEST_N has moved from the EE controller to the AO controller so
the gpio-ranges need to adjusted for it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove pin offset on the EE controller. Meson pinctrl no longer has
this quirk
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the internal phy ACT and LINK leds pinmux
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable saradc and add the reference 1.8v regulator required.
The libretech-cc has saradc channel 0 and 2 available on the 2 first
pins of 2J3 header
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds enables 3 instances of root complexes which are
exposed on DB820c board. 3 Instances are terminted as below
PCIE0 => QCA6174
PCIE1 => MINI PCIE CARD
PCIE2 => GBE ETHERNET
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to 3 pcie root complexes found on MSM8996.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add binding for tsensor on H3660, this tsensor is used for
SoC thermal control, it supports alarm interrupt.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add CPU idle state nodes to enable C1/C2 idle states.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The hi6220-HiKey board started to name GPIO lines for
96boards, using just the plain names "GPIO-A" etc from the
96boards specification.
Poplar started to use an arbitrary "LS-GPIO-A" (etc) prefix
that is not part of the 96boards specification.
As the former notation arrived first, and we need
consistency among 96board, rectify the Poplar board to use
this too. This is important for userspace that wants to
look up GPIO names from these strings.
Cc: Jiancheng Xue <xuejiancheng@hisilicon.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This adds line names for all the GPIOs I could identify on the HiKey960
schematic.
"GPIO-A" through "GPIO-L" are the most important since they give users
a handle to look up the standard 96boards GPIOs from the GPIO character
device.
The rest of the names are more informational, nice debug information
for "lsgpio" so you can see that the right line is taken for the right
function in the kernel for example.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Zhangfei Gao <zhangfei.gao@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
For detailed coresight topology, Hi6220 has 8xCA53 CPUs and each CPU
has one Embedded Trace Macrocell (ETM); the CPU trace data is output
to the cluster funnel. Due system has another CPU and one MCU, all of
them transfer the trace data through trace bus (ATB) to SoC funnel;
the SoC funnel is connected to Embedded Trace FIFO (ETF) with 8KB
buffer; an non-configurable replicator is used to output trace data
for two sinks, one is Embedded Trace Route (ETR) so trace data can be
saved into DRAM, another is Trace Port Interface Unit (TPIU) for
capturing trace data by external debugger.
According to the Hi6220 coresight topology, this patch is to add
coresight dt nodes.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Li Pengcheng <lipengcheng8@huawei.com>
Signed-off-by: Li Zhong <lizhong11@hisilicon.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Define the Eagle board dependent part of the EtherAVB device node.
Enable DHCP and NFS root for the kernel booting.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car D3, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car V3M, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Interrupt Controller for External Devices
(INTC-EX) on R-Car M3-W, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds gpio hogs for USB3 hub on ULCB Kingfisher board to power up and
remove from reset the hub
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCA9548 I2C switch on I2C4 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCA9548 I2C switch on I2C2 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports TCA9539 gpio expanders on I2C4 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports TCA9539 gpio expanders on I2C2 bus on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports USB3.0 Host on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports PCIE0/1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports HSUSB on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports CAN0/1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SCIF1 on ULCB Kingfisher board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the H3ULCB ES2.0+ SoC with Kingfisher
extension infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the H3ULCB ES1.x SoC with Kingfisher
extension infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the M3ULCB with Kingfisher extension
infotainment board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial common dtsi file for Kingfisher infotainment board (R-Car
Starter Kit extension)
This commit supports the following peripherals:
- HSCIF0
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables PWM channel 0 and 1 on the draak. Each channel
connects to LTC2644 for brightness control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since a R-Car Gen3 bootloader enables the PFC of USB3.0 channel 0,
the USB3.0 host controller works without this setting on the kernel.
But, this setting should have salvator-common.dtsi. So, this patch
adds the pfc node for USB3.0 channel 0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A77970 SoC based Eagle board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
for the boards as all of them are missing their cpu supplies, the OPPs
actually need to follow the <target min max> format as the regulator is
shared between both clusters and the one rk3368 board I have, somehow also
doesn't like the higher opps at all - all of which I only realized after
I brought my rk3368 board online again, after its bootloader broke.
So we revert that OPP addition for now.
And also two fixes for the mipi dsi controller on rk3399, which was
referencing a clock to high up in the clock-tree so that an intermediate
gate could be disabled inadvertently and also needs a clock for its area
in the general register files of the rk3399 soc.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlnL6QsQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgUx1B/4pbbWGvxKA/1Osih4Fs/q8rLzNq9N8tsV1
VEQ06VU0TuuyECiNhCv1sD8QoccdAfAu/QlFM2IVg3Js2HB+CtnYw0LVhMEpdf0m
c4Vh/GgpCIgPTaZTDtcHdHh9VbbYDsgsVgLPiuBnbK98GeDVZCIke10J0cUBrwSY
ncJKFfJQh1wor9p54mQfBWtKWfUfDQYxBpENkwq1SD0TJgE/osyKevWXConjMN1f
vyH+BmEJq96Wz76QqEXtiEU47HoHaIMwA7/2LbRJhe5W3ifBFBQD664RH6L/a28o
IhRTq3pvy4v7lip4OTRMby4+C6Yku7Xb3UF3/HAKPntE5eKlpIjV
=DwOn
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Adding the operating points on rk3368 like they were did not end up well
for the boards as all of them are missing their cpu supplies, the OPPs
actually need to follow the <target min max> format as the regulator is
shared between both clusters and the one rk3368 board I have, somehow also
doesn't like the higher opps at all - all of which I only realized after
I brought my rk3368 board online again, after its bootloader broke.
So we revert that OPP addition for now.
And also two fixes for the mipi dsi controller on rk3399, which was
referencing a clock to high up in the clock-tree so that an intermediate
gate could be disabled inadvertently and also needs a clock for its area
in the general register files of the rk3399 soc.
* tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
Revert "arm64: dts: rockchip: Add basic cpu frequencies for RK3368"
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently if the Foundation model is running ARM Trusted Firmware then
the kernel, which is configured to use spin tables, cannot start secondary
processors or "power off" the simulation.
After adding a couple of labels to the include file and splitting out the
spin-table configuration into a header, we add a couple of new headers
together with two new DTs (GICv2 + PSCI and GICv3 + PSCI).
The new GICv3+PSCI DT has been boot tested, the remaining three (two of
which existed prior to this patch) have been "tested" by decompiling the
blobs and comparing them against a reference.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Fixes: 4503b50eac ("arm64: dts: renesas: r8a77995: draak: enable EthernetAVB")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 133ace3f38 ("arm64: dts: ulcb: Set drive-strength for ravb pins")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 7d73a4da26 ("arm64: dts: r8a7795: salvator-x: Set drive-strength for ravb pins")
Fixes: 4903987033be ("arm64: dts: r8a7796: salvator-x: Set drive-strength for ravb pins")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Armada 8040 DB has numerous PCIe ports, so let's enable a few more
of those PCIe ports that are enabled in the default bootloader
configuration.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The interrupt-map property used in the description of the Marvell
Armada 7K/8K PCIe controllers has a bogus extraneous 0 that causes the
interrupt conversion to not be done properly. This causes the PCIe PME
and AER root port service drivers to fail their initialization:
[ 5.019900] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.028821] pcie_pme: probe of 0001:00:00.0:pcie001 failed with error -22
[ 5.035687] genirq: Setting trigger mode 7 for irq 114 failed (irq_chip_set_type_parent+0x0/0x30)
[ 5.044614] aer: probe of 0001:00:00.0:pcie002 failed with error -22
This problem was introduced when the interrupt description was
switched from using the GIC directly to using the ICU interrupt
controller. Indeed, the GIC has address-cells = <1>, which requires a
parent unit address, while the ICU has address-cells = <0>.
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The spi controller nodes omit the dma controller/channel references, add
it.
This does not yet enable DMA for SPI transfers, as the spi-sun6i driver
lacks support for DMA, but always uses PIO to the FIFO.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals. The last used DRQ port is 27.
Add a device node for it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NAND controller used in A7K/A8K is present on the CP110 master part.
It is compatible with the pxa3xx_nand driver but requires the use of the
marvell,armada-8k-nand compatible string due to the need to first enable
the NAND controller.
Add properties to the NAND node to fit the bindings constraints of the
pxa3xx_nand driver and enable the NAND controller.
Add the 'marvell,system-controller' property to the cp110 master NAND
node with a reference to the syscon node. This is new compared to other
boards using the pxa3xx_nand driver and it is needed to be bootloader
independent and enable the NAND controller from the NAND controller
driver itself by writing in these syscon registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[miquel.raynal@free-electrons.com: add NAND ready/busy MPP subnode,
change compatible string to fit the needs of the A7k/A8k SoCs and add
the system controller property]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
This patch fix the warning "xxx has a unit name, but no reg property" by
removing "@0" from such node
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The clk of grf must be enabled before writing grf
register for rk3399.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
[the grf clock is already part of the binding since march 2017]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables the SFP ports on the Armada 8040 DB as these ports
are now supported by the PPv2 driver (since the PHY is now optional).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch enables the SFP port on the Armada 7040 DB as this port
is now supported by the PPv2 driver (since the PHY is now optional).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds a comphy phandle to the Ethernet port in the 7040-db
device tree. The comphy is used to configure the serdes PHYs used by
these ports.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds comphy phandles to the Ethernet ports in the mcbin
device tree. The comphy is used to configure the serdes PHYs used by
these ports.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add ITS device tree node, which will be used by PCIe controller.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The physical memory map address and CCSR registers map address are
different between LS2088A and other LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the reset manager includes for Stratix10. Need to use the '#include'
instead of '/include/' to avoid a DTC syntax error.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Cosmetic patch removing an empty line at the end of the NB pinctrl node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Ports interrupts are used by the PPv2 driver when no PHY is connected to
a port. This patch adds a description of these interrupts.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch describes the comphy available in the cp110 master and slave.
This comphy provides serdes lanes used by various controllers such as
the network one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch extends on both cp110 the system register area length to
include some of the comphy registers as well.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
There is a further gate in between the mipidphy reference clock and the
actual ref-clock input to the dsi host, making the clock hirarchy look like
clk_24m --> Gate11[14] --> clk_mipidphy_ref --> Gate21[0] --> clk_dphy_pll
Fix the clock reference so that the whole clock subtree gets enabled when
the dsi host needs it.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
[amended commit message]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Extend the container size to 0x2000 to include the gpio controller at
offset 0x1040.
While at it, add start address notation to the gpio node name to match
its 'offset' property.
Fixes: 63dac0f492 ("arm64: dts: marvell: add gpio support for Armada
7K/8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
the UART1 registers that should not be declared in this node.
Update the example in DT bindings document accordingly.
Signed-off-by: allen yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By adding this regulator, a proper reset is done during boot. Without
this, the UHS failed to be detected after a warm reboot when the SD card
remained in the slot, then it fallback to an HS.
Note that the vmcc is supported by the xenon driver only with the
following fix: "mmc: sdhci-xenon: add set_power callback".
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the relevant details in the Armada 7K/8K Device Tree
to properly mux the UART used for the serial console. Since there is
basically only one possible muxing for the UART0 on the AP, the muxing
configuration is described in armada-ap806.dtsi, and selected from the
individual boards (other boards could be using a different UART).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The downstream RTD1195 and apparently RTD1295 trees have a modified 8250
serial driver that acknowledges its interrupts using the second reg area,
which is an irq mux.
Drop these unused second reg entries for the UART nodes.
Fixes: 72a7786c0a ("ARM64: dts: Add Realtek RTD1295 and Zidoo X9S")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Define the generic R8A77970 part of the EtherAVB device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF ports in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC1/2 in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A77970 SoC device tree including Cortex-A53 CPU, GIC, timer,
CPG, RST, and SYSC.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded clock indices by R8A77995_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded power domain indices by R8A77995_PD_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Node names should not use numerical suffixes if the nodes can be
distinguished by unit-address.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU is already wired up to the HDMI encoder, all we need to do is
enable it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch changes the name from from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000 like other Renesas
SoCs.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7796 has a single FDP1 instance.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The A64 SPI controllers are register compatible to the h3/h5 SPI
controllers.
The A64 has two SPI controllers, each with a single chip select.
The handles for the DMA channels (23/24 for SPI0/SPI1) are omitted,
as the A64 DMA support is currently missing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators, replace
fixed regulator with AXP803 dcdc1 regulator.
Tested on pine64.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the graphics-related nodes on the rk3399-firefly which makes
it possible to see output on the on-board hdmi output.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3328 Evaluation Board use rk805 pmic, and one of the DCDCs in
rk805 is for cpu regulator, assign the cpu regulator, so the
cpufreq can work fine.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This reverts commit 6f2dea1f5f.
Without accurate cpu regulators being set for boards this will wreak havoc
when cpufreq-dt begins to set new frequencies without adjusting the core
frequency.
Additionally the rk3368 has an unsolved issue in that it has two separate
cpu clusters with separate clock lines but only one cpu supply regulator
for both clusters, which causes even more problems.
While it seems that originally only one cluster was supposed to be active
at a time (big or little), talking with real users of the hardware
revealed that having all 8 cores accessible at 1.2GHz max is way more
liked than having 4 cores at 1.5GHz max. Such an approach needs changes
to cpufreq and/or opp though to control the two separate clock lines when
setting both clusters to the same frequencies.
In any case, having the OPPs in the dts at this point in time is
undesireable, so remove them again for now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
SDR104 seems to be OK on the nanopi-k2 SBC so enable it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable UHS modes, up to SDR50, on the nanopi-k2 SBC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable sdcard UHS modes, up to SDR50, on p20x based boards.
While the s905 supports SDR104 mode, it appears that the PCB of p20x
based boards can't cope with a rate as high as 200Mhz.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable sdcard UHS modes up to SDR50. Unfortunately, it seems the PCB of
the libretech-cc cannot handle SDR104 at 200Mhz reliably.
Also enable eMMC DDR52 mode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Changing the card voltage on the cc is not instantaneous, especially
when switching from 3.3v to 1.8v.
It take at least 30ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: 61ff2af9b278 ("ARM64: dts: fixup libretech cc definition")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Changing the card voltage on the nanopi-k2 is not instantaneous,
especially when switching from 3.3v to 1.8v.
It take at least 3ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: 9bc7ffb08d ("arm64: dts: amlogic: Add NanoPi K2")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that the clock source 0 is properly described in the CCF, use it
instead of assuming the default value (xtal)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
-----BEGIN PGP SIGNATURE-----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=5fxW
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.14 merge window.
I'm sending this early, as my continuing journey into fatherhood is
occurring really soon now, I'm going to be mostly useless for the next
couple of weeks, though I may be able to read email, I doubt I'll be
doing much patch applications or git sending. If anything urgent pops
up I've asked Daniel/Jani/Alex/Sean to try and direct stuff towards
you.
Outside drm changes:
Some rcar-du updates that touch the V4L tree, all acks should be in
place. It adds one export to the radix tree code for new i915 use
case. There are some minor AGP cleanups (don't see that too often).
Changes to the vbox driver in staging to avoid breaking compilation.
Summary:
core:
- Atomic helper fixes
- Atomic UAPI fixes
- Add YCBCR 4:2:0 support
- Drop set_busid hook
- Refactor fb_helper locking
- Remove a bunch of internal APIs
- Add a bunch of better default handlers
- Format modifier/blob plane property added
- More internal header refactoring
- Make more internal API names consistent
- Enhanced syncobj APIs (wait/signal/reset/create signalled)
bridge:
- Add Synopsys Designware MIPI DSI host bridge driver
tiny:
- Add Pervasive Displays RePaper displays
- Add support for LEGO MINDSTORMS EV3 LCD
i915:
- Lots of GEN10/CNL support patches
- drm syncobj support
- Skylake+ watermark refactoring
- GVT vGPU 48-bit ppgtt support
- GVT performance improvements
- NOA change ioctl
- CCS (color compression) scanout support
- GPU reset improvements
amdgpu:
- Initial hugepage support
- BO migration logic rework
- Vega10 improvements
- Powerplay fixes
- Stop reprogramming the MC
- Fixes for ACP audio on stoney
- SR-IOV fixes/improvements
- Command submission overhead improvements
amdkfd:
- Non-dGPU upstreaming patches
- Scratch VA ioctl
- Image tiling modes
- Update PM4 headers for new firmware
- Drop all BUG_ONs.
nouveau:
- GP108 modesetting support.
- Disable MSI on big endian.
vmwgfx:
- Add fence fd support.
msm:
- Runtime PM improvements
exynos:
- NV12MT support
- Refactor KMS drivers
imx-drm:
- Lock scanout channel to improve memory bw
- Cleanups
etnaviv:
- GEM object population fixes
tegra:
- Prep work for Tegra186 support
- PRIME mmap support
sunxi:
- HDMI support improvements
- HDMI CEC support
omapdrm:
- HDMI hotplug IRQ support
- Big driver cleanup
- OMAP5 DSI support
rcar-du:
- vblank fixes
- VSP1 updates
arcgpu:
- Minor fixes
stm:
- Add STM32 DSI controller driver
dw_hdmi:
- Add support for Rockchip RK3399
- HDMI CEC support
atmel-hlcdc:
- Add 8-bit color support
vc4:
- Atomic fixes
- New ioctl to attach a label to a buffer object
- HDMI CEC support
- Allow userspace to dictate rendering order on submit ioctl"
* tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux: (1074 commits)
drm/syncobj: Add a signal ioctl (v3)
drm/syncobj: Add a reset ioctl (v3)
drm/syncobj: Add a syncobj_array_find helper
drm/syncobj: Allow wait for submit and signal behavior (v5)
drm/syncobj: Add a CREATE_SIGNALED flag
drm/syncobj: Add a callback mechanism for replace_fence (v3)
drm/syncobj: add sync obj wait interface. (v8)
i915: Use drm_syncobj_fence_get
drm/syncobj: Add a race-free drm_syncobj_fence_get helper (v2)
drm/syncobj: Rename fence_get to find_fence
drm: kirin: Add mode_valid logic to avoid mode clocks we can't generate
drm/vmwgfx: Bump the version for fence FD support
drm/vmwgfx: Add export fence to file descriptor support
drm/vmwgfx: Add support for imported Fence File Descriptor
drm/vmwgfx: Prepare to support fence fd
drm/vmwgfx: Fix incorrect command header offset at restart
drm/vmwgfx: Support the NOP_ERROR command
drm/vmwgfx: Restart command buffers after errors
drm/vmwgfx: Move irq bottom half processing to threads
drm/vmwgfx: Don't use drm_irq_[un]install
...
Adding more resources on the network controller ppv2.2 on Armada 7K/8K
allowing to use last improvement introduced in the driver.
Also enabling more network ports on the mcbin (A8K base board)
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWaaJiiMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71QonAJ9HyQXhNQBN
BK1PYsmmDqVfNHBesACcCVEof+kHPYIwqLi+lzt2hEGMPmQ=
=ty8P
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-4' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.14 (part 4)
Adding more resources on the network controller ppv2.2 on Armada 7K/8K
allowing to use last improvement introduced in the driver.
Also enabling more network ports on the mcbin (A8K base board)
* tag 'mvebu-dt64-4.14-4' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix number of GPIOs in AP806 description for Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWal5XSMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71W2pAJ90lo/XfZ3O
y7YizLM864H+4XGl9gCeOfmhngOW/lj1gPAVny35hw/ua00=
=2qOU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.13-3' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.13 (part 3)
Fix number of GPIOs in AP806 description for Armada 7K/8K
* tag 'mvebu-fixes-4.13-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to maximize the use of MSI, a PCIe controller will share
all MSI controllers. The patch changes "msi-parent" to refer to all
MSI controller dts nodes.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
"1" should be replaced by "l". This is a typo.
The patch is to fix it.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch enables the two GE/SFP ports. They are configured in 10GKR
mode by default. To do this the cpm_xdmio is enabled as well, and two
phy descriptions are added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The network driver on Marvell SoC (7k/8k) needs to access some registers
in the system controller to configure its ports at runtime. This patch
adds a phandle reference to the syscon system controller node in the
ppv2 node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit updates the Marvell Armada 7K/8K Device Tree to describe
the TX interrupts of the Ethernet controllers, in both the master and
slave CP110s.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Add description for a new family SoC from Marvell: Armada-8KP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmeipsACgkQCwYYjhRyO9UnEACcDuFAUJNT2eth5lYMHoHcvMLf
x7QAnjqghjBpm7nYOutsYPY5gwz/YYC6
=+kES
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.14 (part 3)
Add description for a new family SoC from Marvell: Armada-8KP.
* tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Device Tree files for Armada-8KP
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert all RK3399 platforms to use per-lane PHY model in order to save
more power by idling unused lane(s).
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds reset controller node of analog signal amplifier
core (ADAMV) for UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since i80/command mode is determined in runtime by propagating info
from panel this property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmdnagQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSpBB/9v6flM/QtBVeXhR1tfrXIt3veUaiwiTwhg
PIj6J7EJZCgA9TiHr4zcQzjCx581a9v1rUEpnhZyi7d/zrNurpJRYtBNcqfDS28Z
kyL30gwf/y4nVAzgIODGMNRWe3+IETNCIRZ236cV7jr9HgKmHvA0qc2aMzjHPMCF
XS9wPXgEW1kYIgKqzq1drAWY3iVB0W37KMX9HKVQfAlPcGu5jobk0lruQBZV0InH
8NR3NB9a7eknzPejmBO2ga0idS0oAc/eFQ8h2bHrxWVm1JO+2QDc7epxWCTmxBcP
DLy+7tuQiXEFc25AM3QpW97pJuqDT+zeZXd/F5BK5uGnpH63SNbi
=D65g
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "second round of Rockchip dts64 changes for 4.14" from Heiko Stübner:
3 new boards, the rk3328-based Rock64 from the Pine64-makers, the
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
* tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (29 commits)
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
arm64: dts: rockchip: add rk3328-rock64 board
arm64: dts: rockchip: add rk3328 pdm node
arm64: dts: rockchip: add more rk3399 iommu nodes
arm64: dts: rockchip: add rk3368 iommu nodes
arm64: dts: rockchip: add rk3328 iommu nodes
arm64: dts: rockchip: Add basic cpu frequencies for RK3368
arm64: dts: rockchip: add rk805 node for rk3328-evb
arm64: dts: rockchip: Assign mic irq to correct device for Gru
arm64: dts: rockchip: init rk3399 vop clock rates
arm64: dts: rockchip: Add pwm nodes for rk3328
arm64: dts: rockchip: Fix wrong rt5514 dmic delay property for Gru
arm64: dts: rockchip: disable tx ipgap linecheck for rk3399 dwc3
arm64: dts: rockchip: remove num-slots property from rk3399-sapphire
arm64: dts: rockchip: Enable tsadc module on RK3328 eavluation board
arm64: dts: rockchip: add thermal nodes for rk3328 SoC
arm64: dts: rockchip: add tsadc node for rk3328 SoC
arm64: dts: rockchip: add rk3328 i2s nodes
...
This commit adds the base Device Tree files for the Armada 8KPlus.
The Armada 8KP SoCs include several hardware blocks, and this
commit only adds support for the AP810 block, that contains the CPU
core and basic peripherals.
AP810 is a high-performance die, includes octal core application
processor based ARMv8-A architecture, two standard high speed DDR4
interface, and GIC-600 interrupt controller.
AP810 Built as part of Marvell’s MoChi AP family products.
Armada-8080 (8KPlus family), include an AP810 block that contains
the CPU core and basic peripherals.
This commit creates the following hierarchy:
* armada-ap810-ap0.dtsi - definitions common to AP810
* armada-ap810-ap0-octa-core.dtsi - description of the octa cores
* armada-8080.dtsi - description of the 8080 SoC
* armada-8080-db.dts - description of the 8080 board
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Haikou is a Qseven and μQseven baseboard featuring PCIe, USB3 and a
video connector for MIPI-DSI/CSI and eDP adapter.
This dts is for usage with the RK3399-Q7 SoM Puma.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.
The devicetree currently supports basic peripherals, with more to be
added later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch describes the GPIO lines usage on the LibreTech CC board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: minor whiespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The AO clkc needs to be updated to new bindings with an system control parent
node and moving the clkc node as subnode.
Also adds the SoC specific compatible following the bindings requirements.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This enables option to use dt binding
headers.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable smmu via dtsi. Enable it in board file when needed.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline kernel has r1p12 compatible string now. Use this new compatible
string and also append generic compatible string.
Keep in your mind that using this generic compatible string not all uart
features will be available.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add debug console to dtsi to be able to enable it in
board dts file.
Keep in your mind that every core has separate dcc port in case you want
to run SMP kernel.
DCC is very helpful communication channel for debugging.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added the idle-states node to describe zynqmp idle states. Only
cpu-sleep-0 idle state is added in this patch. References to the
idle-states node are added in all CPU nodes. Time values: entry/exit
latencies and min-residency, needs to be tuned. arm,psci-suspend-param
is selected to comply with PSCIv1.0 and Extended StateID format.
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds and enable the operating points that have been tested and are
currently supported by the SoC. This also adds clocks for ARMCLKL and
ARMCLKB.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808
and RK818 that there are 2 output only GPIOs, we should add
properties "gpio-controller" and "gpio-cells = <2>".
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
-----BEGIN PGP SIGNATURE-----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=u/18
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 device tree changes for 4.14, round 2" from Chen-Yu Tsai:
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
* tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: Add A64-OLinuXino initial support
arm64: allwinner: a64: Add initial NanoPi A64 support
arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64
arm64: allwinner: a64: enable AXP803 for Banana Pi M64
arm64: allwinner: a64: enable USB host controller for BPi M64
Currently we are assigning mic irq to rt5514 i2c driver, which is wrong.
Assign it to rt5514 spi driver instead.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We need to init vop aclk and hclk incase the U-Boot does not do
the initialize.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are 4 pwm channels built in rk3328 soc, need to configure
the both APB clock and bus clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to rt5514 dt-binding, it should be "realtek,dmic-init-delay-ms".
Fixes: 48f4d9796d (arm64: dts: rockchip: add Gru/Kevin DTS)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Enable uSD on ESPRESSObin (Armada 37xx based board)
- Add NAND support on Armada 7K/8K SoCs
- Enable USB host on Armada-7040-DB and Armada-8040-DB boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmWtIYACgkQCwYYjhRyO9V67ACfUFPrkPl8Qn34OAjklU+hVPR9
YJIAn0EI8S47gAuQe0bzEmU45qALL/Xv
=Vf0A
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-2' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt64 for 4.14 (part 2)" from Gregory CLEMENT:
- Enable uSD on ESPRESSObin (Armada 37xx based board)
- Add NAND support on Armada 7K/8K SoCs
- Enable USB host on Armada-7040-DB and Armada-8040-DB boards
* tag 'mvebu-dt64-4.14-2' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: enable USB host on Armada-8040-DB
ARM64: dts: marvell: enable USB host on Armada-7040-DB
ARM64: dts: marvell: add NAND support on the CP110
ARM64: dts: marvell: armada-37xx: Enable uSD on ESPRESSObin
arm64: dts: marvell: Fully re-order nodes in Marvell CP110 dtsi files
* Add PFC device node to R-Car D3 (r8a77995)
This is a step towards enabling devices that use multiplexed pins
- including ethernet - on boards that use the r8a7796 SoC.
* Add USB nodes to R-Car M3-W (r8a7796)
This is a step towards enabling USB devices on boards that
use the r8a7796 SoC.
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Cleanup whitespace and extra LVDS port label
Minor cleanups, no run-time effect.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZlV36AAoJENfPZGlqN0++cwMQAIieFfQzDET0/2dGSWB6oDAt
fSCCHh4l6B5vufUyhV4rDjm8drKgT5sMTkAYh4Y1oq69NV3BFnFb0gr3BY58Qwyv
yz4s2o3UNShVcCuSK8rJaMdr8BOBmKoS2WBMjIOBO+znfhfP1zCbBgDNIanSGMY2
8fmBBB3CF76NM0Juh5FmD1bUsxvzX3ZboyWxQY9u5aIrvcvhau4dcifkKJpcp5gT
b/0z0Vi2ZraPE1JOlIHghc0ph10TYVl1pYINgWhhtybNSd9D2TXgGFfn5XZkdk2+
+Az+mookjAsXIm7hj/3la1KflnT67oWNb6rJkz3TWHkNSFW0AbZb0iEnzP02mIMX
6DsUW8jaAxxviMavLB8+Qi5UMM4q7PY78AWB4VA4etkQf5GL/98Lr/jLayd4vyOt
tJLeE+c89J+eEbql4UfrTl/fdUIjJzH5P9RMG/DUpqAZpw8GlFjx5ZttPKOMUU7V
dN5wuG+ujneedn6Kb0RHeI09/q4MVPcEjxbOGq/Xqljp1wYPf44tkDkBd9ecs047
A9fXEuv3qgU5N8iNyT31nudzNbDTIfDYFg7XBcX5pY7BAnXKbTvfl1mFzHyX9Pm8
GBGFndOrX4b9aPj3JqXMldQOVpKT5YMyFbA2vl4Z1bbqFqE3cdgHSEp5NcC93qRv
1colO4fJ/JaDLKsP5dfH
=6XqO
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Pull "Second Round of Renesas ARM64 Based SoC DT Updates for v4.14" from Simon Horman:
* Add PFC device node to R-Car D3 (r8a77995)
This is a step towards enabling devices that use multiplexed pins
- including ethernet - on boards that use the r8a7796 SoC.
* Add USB nodes to R-Car M3-W (r8a7796)
This is a step towards enabling USB devices on boards that
use the r8a7796 SoC.
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Cleanup whitespace and extra LVDS port label
Minor cleanups, no run-time effect.
* tag 'renesas-arm64-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a77995: add pfc device node
arm64: dts: r8a7796: Add HSUSB device node
arm64: dts: r8a7796: Add USB-DMAC device nodes
arm64: dts: r8a7796: Add USB3.0 host device node
arm64: dts: r8a7796: add USB2.0 Host (EHCI/OHCI) device nodes
arm64: dts: r8a7796: add usb2_phy device nodes
arm64: dts: r8a7795: correct whitespace of companion property
arm64: dts: r8a7795: Use R-Car SATA Gen3 fallback compat string
arm64: dts: salvator-common: Remove extra LVDS port label
* Add IPQ8074 SoC and HK01 board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JCl4
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Pull "Qualcomm ARM64 Updates for v4.14 Part 2" from Andy Gross:
* Add IPQ8074 SoC and HK01 board support
* tag 'qcom-arm64-for-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: Add ipq8074 SoC and HK01 board support
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=WUr3
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
ARM: dts: cygnus: Add generic-ehci/ohci nodes
ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
ARM: dts: cygnus: Add additional peripherals to dtsi
ARM: dts: cygnus: Enable Performance Monitoring Unit
ARM: dts: cygnus: place v3d in proper address ordered location
ARM: dts: cygnus: Fix incorrect UART2 register base
ARM: dts: bcm283x: Add 32-bit enable method for SMP
dt-bindings: arm: add SMP enable-method for BCM2836
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
ARM: dts: NSP: Rearrage USB entries
ARM: dts: NSP: Add dma-coherent to relevant DT entries
ARM: dts: bcm2835: Add Raspberry Pi Zero W
dt-bindings: bcm: Add Raspberry Pi Zero W
ARM: bcm283x: Define UART pinmuxing on board level
ARM: dts: BCM5301X: Specify USB ports for each controller
ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.
- A clean up patch from Shawn Lin to remove the deprecated dwmmc
property 'num-slots' from ZX296718 device tree.
- Enable various devices for ZX296718 SoC support, VGA display, I2S
audio, pinctrl, GPIO, PWM and IRDEC.
- Update zx296718-evb support to use audio-graph-card for HDMI audio
and add I2S sound card.
- Add initial zx296718-pcbox board support with storage, audio,
display devices enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZlo4KAAoJEFBXWFqHsHzOee0H/RcMMznh0cKg8UjjlbAuhArW
4IxmA05TzYBN0VeLNwAzPMn3yrbSZPk5bm7MD/+csv6NuFF2NDlvshyAqWAYueaY
cLXnQvqE3axK5X9xkfQYKvk0OHhj/xIKzEdnJ3++EwEtnibUEl9g8kunopzTQOaq
BsOFTTfuey98hCg4WQSpGIqRhfpKXt/UV63e93TuPs1g0/fpmoooMTQdUE+Wmctq
y1JJb3OC5HMp/NkQRJobmUa2r6R+3T8gmvgFopoBVP543zR5kwJ7bCDXgkzZwIbV
jtLDVCfg+DAapSFpCbULkvOMMZo/rxjAFxP2b8ICFCzNC9zgWpoSAN8ut1Oznk0=
=hAsg
-----END PGP SIGNATURE-----
Merge tag 'zte-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "ZTE arm64 device tree updates for 4.14" from Shawn Guo:
- A clean up patch from Shawn Lin to remove the deprecated dwmmc
property 'num-slots' from ZX296718 device tree.
- Enable various devices for ZX296718 SoC support, VGA display, I2S
audio, pinctrl, GPIO, PWM and IRDEC.
- Update zx296718-evb support to use audio-graph-card for HDMI audio
and add I2S sound card.
- Add initial zx296718-pcbox board support with storage, audio,
display devices enabled.
* tag 'zte-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: zte: add initial zx296718-pcbox board support
arm64: dts: zx296718-evb: add I2S sound card support
arm64: dts: zx296718-evb: use audio-graph-card for HDMI audio
arm64: dts: zx296718: add irdec device for remote control
arm64: dts: zx296718: add PWM device support
arm64: dts: zx296718: add voltage data into OPP table
arm64: dts: zx296718: set a better parent clock for I2S0
arm64: dts: zx296718: add pinctrl and gpio devices
arm64: dts: zx296718: add I2S and I2C audio codec
arm64: dts: zx296718: add VGA device support
arm64: dts: zte: remove num-slots from zx296718
- Correct the typo in fsl-ls1088a-rdb board name.
- A series from Horia Geantă to consolidate aliases node and enable
crypto support for ls208xa and ls1088a.
- Enable USB host support for ls1012a.
- Enable cpuidle support for ls1088a and ls208xa.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZlodKAAoJEFBXWFqHsHzOLYAIAIs6YEEhjbJiet6EMmwpneJo
hTGcU/Gv6q6ozF3uV1+oMqnv64rlzwPR8jTjt29+lCS2I4/zv7Zfr83GR1iMtW90
hIKUMnWwX/ATY1BC4YB36E0Z0WRolNoKU6iKBujMsfxPFRBXulEQwngZoFS5EvHy
TDqCTTRHBHhnzPqMPSJ3q/3r6VPTHDtj1ap+zF8EsS156ybPHhajHm/+u3Kvh6Kh
MnI+Y/SHPFCmy2Pj34SsixGKBEwAukyeddbufUlnrP3wcDnIvv64SWURCsBygEww
jhAD8rYWCFyhqM4vBbQ8AvXrKJkJDZETRy1GTTwDK2MjWeIzY6JtZ+cOGtyBTwU=
=6GLX
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "Freescale arm64 device tree updates for 4.14" from Shawn Guo:
- Correct the typo in fsl-ls1088a-rdb board name.
- A series from Horia Geantă to consolidate aliases node and enable
crypto support for ls208xa and ls1088a.
- Enable USB host support for ls1012a.
- Enable cpuidle support for ls1088a and ls208xa.
* tag 'imx-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls1088: Correction in Board name from "L1088A" to "LS1088A"
arm64: dts: ls208xa: add cpu idle support
arm64: dts: ls1088a: add cpu idle support
arm64: dts: freescale: ls1088a: add crypto node
arm64: dts: freescale: ls208xa: add crypto node
arm64: dts: freescale: ls208xa: share aliases node
arm64: dts: ls1012a: add USB host controller nodes
4.14, please pull the following:
- Scott moves all the Northstar 2 DTS files into a sub-directory to be consistent
with what was done for stingray and to future proof the addition of new board
DTS files
- Velibor adds the ARM CCN-502 interconnect DT node to the Stingray SoC
DTS include file
- Srinath adds the MDIO multiplexer and SATA nodes to the Stingray DTS
include files
- Anup adds the SP804 timers, FlexRM (mailbox) and RAID engine DT nodes
to the Stingray DTS include files
- Abishek adds the BGMAC (Ethernet controller) node to the Stingray DTS
files
-----BEGIN PGP SIGNATURE-----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=0wLC
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64
Pull "Broadcom devicetree-arm64 changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs Device Tree changes for
4.14, please pull the following:
- Scott moves all the Northstar 2 DTS files into a sub-directory to be consistent
with what was done for stingray and to future proof the addition of new board
DTS files
- Velibor adds the ARM CCN-502 interconnect DT node to the Stingray SoC
DTS include file
- Srinath adds the MDIO multiplexer and SATA nodes to the Stingray DTS
include files
- Anup adds the SP804 timers, FlexRM (mailbox) and RAID engine DT nodes
to the Stingray DTS include files
- Abishek adds the BGMAC (Ethernet controller) node to the Stingray DTS
files
* tag 'arm-soc/for-4.14/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: Add SBA-RAID DT nodes for Stingray SoC
arm64: dts: Add FlexRM DT nodes for Stingray
arm64: dts: Add SATA DT nodes for Stingray SoC
arm64: dts: Add DT node to enable BGMAC driver on Stingray
arm64: dts: Add sp804 DT nodes for Stingray SoC
arm64: dts: Add MDIO multiplexer DT node for Stingray
arm64: dts: Enable stats for CCN-502 interconnect on Stingray
arm64: dts: move ns2 into northstar2 directory
Three fixes adding a missing alias for the Ethernet controller on A64
boards. One adding a missing interrupt for the pin controller.
-----BEGIN PGP SIGNATURE-----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=lSDD
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.13, round 2" from Chen-Yu Tsai:
Three fixes adding a missing alias for the Ethernet controller on A64
boards. One adding a missing interrupt for the pin controller.
* tag 'sunxi-fixes-for-4.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
RK3399 USB DWC3 controller has a issue that FS/LS devices not
recognized if inserted through USB 3.0 HUB. It's because that
the inter-packet delay between the SSPLIT token to SETUP token
is about 566ns, more then the USB spec requirement.
This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to
disable the u2mac linestate check to decrease the SSPLIT token
to SETUP token inter-packet delay from 566ns to 466ns.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After adding the clock subsystem to the SOC, the dummy
clock clk32k is not longer needed. Delete it.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use newly added R-Car SATA Gen3 fallback compat string
in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The DU LVDS output is on port 3 on R8A7795 but on port 2 on R8A7796. The
lvds_connector label thus can't be defined in salvator-common.dtsi,
common to the two SoCs.
The lvds_connector label is meant for convenience to be referenced from
panel device tree files, such as r8a77xx-aa104xd12-panel.dtsi or
r8a77xx-aa121td01-panel.dtsi. As those files are not included in any
device tree source, and the label never used elsewhere, we can simply
remove it. Out-of-tree patches that include panel device tree files can
then add a
#define lvds_connector du_out_lvds0
before including the panel device tree file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Avoid audio_clkout naming conflict for salvator boards using
Renesas R-Car Gen 3 SoCs
Morimoto-san says "The clock name of "audio_clkout" is used by the
Renesas sound driver. This duplicated naming breaks its clock
registering/unregistering. Especially when unbind/bind it can't handle
clkout correctly. This patch renames "audio_clkout" to "audio-clkout" to
avoid the naming conflict."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=meey
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Fourth Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
* Avoid audio_clkout naming conflict for salvator boards using
Renesas R-Car Gen 3 SoCs
Morimoto-san says "The clock name of "audio_clkout" is used by the
Renesas sound driver. This duplicated naming breaks its clock
registering/unregistering. Especially when unbind/bind it can't handle
clkout correctly. This patch renames "audio_clkout" to "audio-clkout" to
avoid the naming conflict."
* tag 'renesas-fixes4-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: salvator-common: avoid audio_clkout naming conflict
Corentin Labbe