Add the switch device node, available on PF5, so that the switch port
sub-nodes (net devices) can be linked to corresponding board specific
phy nodes (external ports) or have their link mode defined (internal
ports).
The switch device features 6 ports, 4 with external links and 2
internally facing to the LS1028A SoC and connected via fixed links to 2
internal ENETC Ethernet controller ports.
Add the corresponding ENETC host port device nodes, mapped to PF2 and
PF6 PCIe functions. Since the switch only supports tagging on one CPU
port, only one port pair (swp4, eno2) is enabled by default and the
other, lower speed, port pair is disabled to prevent the PCI core from
probing them. If enabled, swp5 will be a fixed-link slave port.
DSA tagging can also be moved from the swp4-eno2 2.5G port pair to the
1G swp5-eno3 pair by changing the ethernet = <&enetc_port2> phandle to
<&enetc_port3> and moving it under port5, but in that case enetc_port2
should not be disabled, because it is the hardware owner of the Felix
PCS and disabling its memory would result in access faults in the Felix
DSA driver.
All ports are disabled by default, including the CPU port, and need to
be enabled on a per-board basis.
The phy-mode binding of the internal ENETC ports was modified from
"gmii" to "internal" to match the phy-mode of the internal-facing switch
ports connected to them. The ENETC driver does not perform any phy_mode
validation anyway, so the change is only cosmetic. Also, enetc_port2 is
defined as a fixed-link 1000 Mbps port even though it is 2500 Mbps (as
can be seen by the fact that it is connected to mscc_felix_port4). The
fact that it is currently defined as 1000 Mbps is an artifact of its
PHYLIB implementation instead of PHYLINK (the former can't describe a
fixed-link speed higher than what swphy can emulate from the Clause 22
MDIO spec).
The switch's INTB interrupt line signals:
- PTP TX timestamp availability
- TSN Frame Preemption
And don't forget to enable the 4MB BAR4 in the root complex ECAM space,
where the switch registers are mapped.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are few boards that enable all ENETC ports, so instead of having
board DTs disable them, do so in the DTSI and have the boards enable the
ports they use.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This specifier overrides the interrupt specifier with 3 cells from gic
(/interrupt-controller@6000000), but in fact ENETC is not an interrupt
controller, so the property is bogus.
Interrupts used by the children of the ENETC RCIE must use the full
3-cell specifier required by the GIC.
The issue has no functional consequence so there is no real reason to
port the patch to stable trees.
Fixes: 927d7f8575 ("arm64: dts: fsl: ls1028a: Add PCI IERC node and ENETC endpoints")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sm8250 devicetree file for SM8250 SoC and SM8250 MTP platform.
This file adds the basic nodes like cpu, psci and other required
configuration for booting up to the serial console.
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200310050910.506854-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Disable Coresight funnel 4 and 5, for now, as these causes the MTP to
crash when clock late_initcall disables unused clocks.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200308055445.1992189-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch increases the reg addresses for QSPI boot and QSPI rootfs for
Stratix10 and Agilex to cater for the increased size of kernel Image.
Signed-off-by: Joyce Ooi <joyce.ooi@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Both, OrangePi One Plus and OrangePi Lite 2 have HDMI output. Enable it
in common DTSI.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
[patch split and commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Christopher Obbard <chris@64studio.com>
Tested-by: Christopher Obbard <chris@64studio.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
OrangePi One Plus has gigabit ethernet. Add nodes for it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
[patch split and commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Christopher Obbard <chris@64studio.com>
Tested-by: Christopher Obbard <chris@64studio.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
It turns out that not all H6 boards have external 32kHz oscillator.
Currently the only one known such H6 board is Tanix TX6.
Move external oscillator node from common H6 dtsi to board specific dts
files where present.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified in the smd-rpm-regulator binding and confirmed by the
pm8616 device specification, there is no vdd_l5. l5 vdd comes from
vdd_l4_l5_l6. Fix that (though it does not cause any issue since
the supply is not requested).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1583516368-29593-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
To enable kernel critical shutdown feature added critical trip point to
all non CPU sensors to perform shutdown in orderly manner.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rajeshwari <rkambl@codeaurora.org>
Link: https://lore.kernel.org/r/1583394547-12779-2-git-send-email-rkambl@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The CLKREF clocks in GCC are parented by RPM_SMD_LN_BB_CLK, through the
CXO2 pad. Wire this up so that this is properly enabled when need by the
various PHYs.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200106080546.3192125-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There is no enable-gpio for backlight control on rk3399 evb,
actually GPIO1_B5 is for LCD panle enable. So remove it from backlight
dt node.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20200305113912.32226-4-andy.yan@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the DT nodes for each of the Network-On-Chip interconnect
buses found on SDM845 based platform and redefine the rsc_hlos
child node as a bcm-voter device to better represent the hardware.
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200209183411.17195-7-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is just like commit a1875bf982 ("arm64: dts: qcom: sdm845: Add
unit name to soc node") but for sc7180.
For reference, the warning being fixed was:
Warning (unit_address_vs_reg): /soc:
node has a reg or ranges property, but no unit name
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 90db71e480 ("arm64: dts: sc7180: Add minimal dts/dtsi files for SC7180 soc")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200304105638.1.I9ea0d337fcb927f52a28b20613b2377b6249c222@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Discussing the YAML validation schema with the DT maintainers
it came out that a bus named "smb@80000000" is not really
accepted, and the schema was written to name the static memory
bus just "bus@80000000".
This change is necessary for the schema to kick in and validate
these device trees, else the schema gets ignored.
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
-----BEGIN PGP SIGNATURE-----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=VAHM
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: agilex: fix gmac compatible
- The compatible for Agilex GMAC should be "altr,socfpga-stmmac-a10-s10"
* tag 'socfpga_dts_fix_for_v5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: (578 commits)
arm64: dts: socfpga: agilex: Fix gmac compatible
Linux 5.6-rc4
KVM: VMX: check descriptor table exits on instruction emulation
ext4: potential crash on allocation error in ext4_alloc_flex_bg_array()
macintosh: therm_windtunnel: fix regression when instantiating devices
jbd2: fix data races at struct journal_head
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
MAINTAINERS: Correct Cadence PCI driver path
io_uring: fix 32-bit compatability with sendmsg/recvmsg
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
...
Link: https://lore.kernel.org/r/20200303153509.28248-1-dinguyen@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix gmac compatible string to "altr,socfpga-stmmac-a10-s10". Gmac for
Agilex should use same compatible as Stratix 10.
Fixes: 4b36daf9ad ("arm64: dts: agilex: Add initial support for Intel's Agilex SoCFPGA")
Cc: stable@vger.kernel.org
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This is largely cosmetic, but Odroid N2 and Khadas VIM3 are G12B devices so
correct the card model names to reflect this.
Fixes: aa7d5873bf ("arm64: dts: meson-g12b-odroid-n2: add sound card")
Fixes: c6d29c66e5 ("arm64: dts: meson-g12b-khadas-vim3: add initial device-tree")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[khilman: fix whitespace in commit log trailers]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1583135051-95529-1-git-send-email-christianshewitt@gmail.com
videostrong kii pro comes with a nec rc, add the keymap to the dts
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
before
[6.418252] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.435663] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.551259] brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
[6.551275] brcmfmac: brcmf_sdio_verifymemory: error -84 on reading 2048 membytes at 0x00184000
[6.551352] brcmfmac: brcmf_sdio_download_firmware: dongle image file download failed
after
[6.657165] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.660807] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918643] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918734] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[6.922724] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4356/2 wl0: Jun 16 2015 14:25:06 version 7.35.184.r1 (TOB) (r559293) FWID 01-b22ae69c
Fixes: adc52bf7ef ("arm64: dts: meson: fix mmc v2 chips max frequencies")
Suggested-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1582212790-11402-1-git-send-email-christianshewitt@gmail.com
The lvds controller has two ports. port@0 for the connection
to the display controller(s) and port@1 for the connection to
the panel, so should have a ports node covering the port@x nodes.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20200121222055.4068166-1-heiko@sntech.de
Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue
where tx checksumming does not work with packets larger than 1498.
The default Programmable Buffer Length for TX in these GMAC's is
not suitable for MTUs higher than 1498. The workaround is to disable
TX offloading with 'ethtool -K eth0 tx off rx off' causing performance
impacts as it disables hardware checksumming.
This patch sets snps,txpbl to 0x4 which is a safe number tested ok for
the most popular MTU value of 1500.
For reference, see https://lkml.org/lkml/2019/4/1/1382.
Signed-off-by: Carlos de Paula <me@carlosedp.com>
Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399pro-rock-pi-n10.dt.yaml: /: compatible:
['radxa,rockpi-n10', 'rockchip,rk3399pro']
is not valid under any of the given schemas
During the review process the binding was changed,
but the dts file was somehow not updated.
Fix this error by adding 'vamrs,rk3399pro-vmarc-som' to
the compatible property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228061436.13506-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives these errors:
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: usb@ff300000:
'g-use-dma', 'power-domains' do not match any of the regexes:
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-a1.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-rock64.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dt.yaml: usb@ff580000:
'g-use-dma' does not match any of the regexes: 'pinctrl-[0-9]+'
'g-use-dma' is not a valid option in dwc2.yaml, so remove it
from all Rockchip dtsi files.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/dwc2.yaml
g-use-dma was deprecated in november 2016, see
https://patchwork.kernel.org/patch/9420553/
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228113922.20266-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example these errors:
arch/arm64/boot/dts/rockchip/rk3308-evb.dt.yaml: cpu@0: compatible:
Additional items are not allowed ('arm,armv8' was unexpected)
arch/arm64/boot/dts/rockchip/rk3308-evb.dt.yaml: cpu@0: compatible:
['arm,cortex-a35', 'arm,armv8']
is too long
Fix these errors by removing the last argument of
the cpu compatible property in rk3308.dtsi.
make ARCH=arm64
dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/cpus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20200228084827.16198-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT8516 SoC provides the following peripherals: GPIO, UART, USB2,
SPI, eMMC, SDIO, NAND, Flash, ADC, I2C, PWM, Timers, IR, Ethernet, and
Audio (I2S, SPDIF, TDM).
This commit is adding the basic dtsi file with the support of the
following IOs: GPIO, UART, SPI, eMMC, I2C, Timers.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This was missed from the previous fix.
Fixes: b07a11dbdf ("arm64: dts: meson-gxbb-vega-s95: fix WiFi/BT module support")
Suggested-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1582220642-14133-1-git-send-email-christianshewitt@gmail.com
This removes the uart_A alias (no longer required) and adds the bluetooth
node to the P212 device tree.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1582216366-12964-1-git-send-email-christianshewitt@gmail.com
Fixes: adc52bf7ef ("arm64: dts: meson: fix mmc v2 chips max frequencies")
before
[6.418252] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.435663] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.551259] brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
[6.551275] brcmfmac: brcmf_sdio_verifymemory: error -84 on reading 2048 membytes at 0x00184000
[6.551352] brcmfmac: brcmf_sdio_download_firmware: dongle image file download failed
after
[6.657165] brcmfmac: F1 signature read @0x18000000=0x17224356
[6.660807] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918643] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[6.918734] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[6.922724] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4356/2 wl0: Jun 16 2015 14:25:06 version 7.35.184.r1 (TOB) (r559293) FWID 01-b22ae69c
Suggested-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1582212790-11402-1-git-send-email-christianshewitt@gmail.com
A codec node of the sei510 sound card is numbered with the pattern
codec@XX. This pattern should be used only if there is a reg property in
the node which is not case here. Change this to something acceptable.
This change is only to better comply with the DT spec. No functional
changes expected.
Fixes: 64c10554bf ("arm64: dts: meson: sei510: add sound card")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200224150812.263980-4-jbrunet@baylibre.com
Some codec nodes of the s400 sound card are numbered with the pattern
codec@XX. This pattern should be used only if there is a reg property in
the node which is not case here. Change this to something acceptable.
This change is only to better comply with the DT spec. No functional
changes expected.
Fixes: 6f59dc1afb ("arm64: dts: meson-axg: s400: add sound card")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200224150812.263980-3-jbrunet@baylibre.com
When high load on the DWC3 SuperSpeed port, the controller crashes with:
[ 221.141621] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
[ 221.157631] xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
[ 221.157635] xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
[ 221.159901] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
[ 221.159961] hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
[ 221.160076] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
[ 221.165946] usb 2-1.1-port1: cannot reset (err = -22)
Setting the parkmode_disable_ss_quirk quirk fixes the issue.
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
CC: Dongjin Kim <tobetter@gmail.com>
Link: https://lore.kernel.org/r/20200221091532.8142-4-narmstrong@baylibre.com
videostrong kii pro comes with a nec rc, add the keymap to the dts
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200214085802.28742-4-mohammad.rasim96@gmail.com
Follow the standard nodename pattern "^nand-controller(@.*)?" defined
in Documentation/devicetree/bindings/mtd/nand-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
nand@68000000: $nodename:0: 'nand@68000000' does not match '^nand-controller(@.*)?'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^interrupt-controller(@[0-9a-f,]+)*$"
defined in schemas/interrupt-controller.yaml of dt-schema.
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
aidet@5fc20000: $nodename:0: 'aidet@5fc20000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^mmc(@.*)?$" defined in
Documentation/devicetree/bindings/mmc/mmc-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
sdhc@5a000000: $nodename:0: 'sdhc@5a000000' does not match '^mmc(@.*)?$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The qcom-tsens binding requires a SoC-specific and a TSENS
family-specific binding to be specified in the compatible string.
Since them family-specific binding is not listed in the .dtsi file, we
see the following warnings in 'make dtbs_check'. Fix them.
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8996-tsens'] is not valid
under any of the given schemas (Possible causes of the failure):
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8996-tsens'] is too short
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8916-tsens', 'qcom,msm8974-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8976-tsens', 'qcom,qcs404-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible: ['qcom,msm8996-tsens'] is not valid
under any of the given schemas (Possible causes of the failure):
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible: ['qcom,msm8996-tsens'] is too short
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8916-tsens', 'qcom,msm8974-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8996-mtp.dt.yaml:
thermal-sensor@4ad000: compatible:0: 'qcom,msm8996-tsens' is not one of
['qcom,msm8976-tsens', 'qcom,qcs404-tsens']
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/ebaa801adade53c567857db2f74af7d2e00f935b.1582871139.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The qcom-tsens binding requires a SoC-specific and a TSENS
family-specific binding to be specified in the compatible string.
Since them family-specific binding is not listed in the .dtsi file, we
see the following warnings in 'make dtbs_check'. Fix them.
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8916-tsens'] is not valid
under any of the given schemas (Possible causes of the failure):
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible: ['qcom,msm8916-tsens'] is too short
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8916-tsens' is not one of
['qcom,msm8976-tsens', 'qcom,qcs404-tsens']
/home/amit/work/builds/build-aarch64/arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml:
thermal-sensor@4a9000: compatible:0: 'qcom,msm8916-tsens' is not one of
['qcom,msm8996-tsens', 'qcom,msm8998-tsens', 'qcom,sdm845-tsens']
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/8cea8c0036703bcc4dd2b87a8ca3913c4a28d16e.1582871139.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bring in the Truly display and enable the DSI channels to make the
mdss/gpu probe, even though we're lacking LABIB, preventing us from
seeing anything on the screen.
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Link: https://lore.kernel.org/r/20190513210747.22429-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Per convention device nodes for SC7180 should be ordered by address.
This is currently not the case for the venus node, move it to the
correct position.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200227092649.v3.1.I15e0f7eff0c67a2b49d4992f9d80fc1d2fdadf63@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move all pmdomain and clock resources to Venus DT node. And make
possible to support dynamic core assignment on v4.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Link: https://lore.kernel.org/r/20200106154929.4331-12-stanimir.varbanov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
At the moment PinePhone comes in two slightly incompatible variants:
- 1.0: Early Developer Batch
- 1.1: Braveheart Batch
There will be at least one more incompatible variant in the very near
future, so let's start by sharing the dtsi among multiple variants,
right away, even though the HW description doesn't yet include the
different bits.
The differences between 1.0 and 1.1 are: change in pins that control
the flash LED, differences in modem power status signal routing, and
maybe some other subtler things, that have not been determined yet.
This is a basic DT that includes only features that are already
supported by mainline drivers.
Co-developed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Co-developed-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
PinePhone needs I2C2 pins description. Add it, and make it default
for i2c2, since it's the only possiblilty.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and
eDP panel input. The bridge is controlled via I2C that's connected to
R_I2C bus.
Enable all this hardware in device tree.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The commit 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
introduced support for the PMU found on the Allwinner H6. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: 7aa9b9eb7d ("arm64: dts: allwinner: H6: Add PMU mode")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The commit c35a516a46 ("arm64: dts: allwinner: H5: Add PMU node")
introduced support for the PMU found on the Allwinner H5. However, the
binding only allows for a single compatible, while the patch was adding
two.
Make sure we follow the binding.
Fixes: c35a516a46 ("arm64: dts: allwinner: H5: Add PMU node")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add the display, video & graphics clock controller nodes supported on
SC7180.
NOTE: the dispcc needs input clocks from various PHYs that aren't in
the device tree yet. For now we'll leave these stubbed out with <0>,
which is apparently the magic way to do this. These clocks aren't
really "optional" and this stubbing out method is apparently the best
way to handle it.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.15.I1a4b93fb005791e29a9dcf288fc8bd459a555a59@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're transitioning over to requiring the Qualcomm Video Clock
Controller to specify all the input clocks. Let's add the one input
clock for the videocc for sdm845.
NOTE: Until the Linux driver for sdm845's video is updated, this clock
will not actually be used in Linux. It will continue to use global
clock names to match things up.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.14.Id0599319487f075808baba7cba02c4c3c486dc80@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're transitioning over to requiring the Qualcomm GPU Clock
Controller to specify all the input clocks. Let's add them for
sdm845.
As part of this we've decided that the xo clock should be referred to
in the bindings as "bi_tcxo". Change the dts.
NOTE: Until the Linux driver for sdm845's gpucc is updated, these
clocks will not actually be used in Linux. It will continue to use
global clock names to match things up. Of course, Linux didn't use
the old "xo" clock anyway.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.8.If8596faf02408cef4bb9f52296b911eb9ba49287@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're transitioning over to requiring the Qualcomm Display Clock
Controller to specify all the input clocks. Let's add them for
sdm845.
NOTES:
- Until the Linux driver for sdm845's dispcc is updated, these clocks
will not actually be used in Linux. It will continue to use global
clock names to match things up.
- Although the clocks from the DP PHY are required, the DP PHY isn't
represented in the dts yet. Apparently the magic for this is just
to use <0>.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200203103049.v4.3.Ie80fa74e1774f4317d80d70d30ef4b78f16cc8df@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per the bindings, the SDHCI controller should have a SoC-specific
compatible string in addition to the generic version-based one. Add
it.
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Fixes: 7241ab944d ("arm64: dts: qcom: qcs404: Add sdcc1 node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200127082331.1.I402470e4a162d69fde47ee2ea708b15bde9751f9@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds the gpio-ranges property to almost all of
the Qualcomm ARM platforms that utilize the pinctrl-msm
framework.
The gpio-ranges property is part of the gpiolib subsystem.
As a result, the binding text is available in section
"2.1 gpio- and pin-controller interaction" of
Documentation/devicetree/bindings/gpio/gpio.txt
For more information please see the patch titled:
"pinctrl: msm: fix gpio-hog related boot issues" from
this series.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Robert Marko <robert.marko@sartura.hr> [ipq4019]
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20200108125455.308969-2-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some platforms don't want to use the pmic power key as the power key
event. Add a label so platforms can easily reference and mark this node
as status = "disabled".
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200115025314.3054-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5TuEMUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4a+Qf9Enb2G47LTMeYH5JYhm2anDQ4lz+8
Og1bcGPYKilDhc4YzpAIhRnOTLa9TietZSS0tyNFk37GDfKRjn9gxXDRbI+4lrJc
UOSLpWCB4BnzKc+FoCHC37jkdkMD3V2E5MmFHtYkGYmH0DAi8cLmGebmgGujd0GJ
lx2/5EbxKoJxeA2i79H5OAPBhglJsEnPTSulZ+jUdLzJfBlRBIQBc3oPcwnRIibr
VUbLc4Gkb2kTe6NwdQTjqI+4BTHv7/4m+twOojO5Z8QBH4X+3bkLnLiylhuqHBeR
cDXGL7sHkekZhDQ3OwIMiT/5cc8SxplqAl6QMm8+/9gq7KfAucy8Psokow==
=dg69
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.6:
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
* tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
arm64: dts: imx8qxp-mek: Remove unexisting Ethernet PHY
ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties
ARM: dts: ls1021a: Restore MDIO compatible to gianfar
ARM: dts: imx7d: fix opp-supported-hw
ARM: imx: build v7_cpu_resume() unconditionally
ARM: dts: imx6: phycore-som: fix emmc supply
Link: https://lore.kernel.org/r/20200224120334.GH27688@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Orange Pi PC2 features sy8106a regulator just like Orange Pi PC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
According to latest datasheet Rev.0, 10/2019, there is restriction
as below:
"If VDD_SOC/GPU/DDR = 0.95V, then VDD_ARM must be >= 0.95V."
As by default SoC is running at OD mode(VDD_SOC = 0.95V), so
VDD_ARM 1.2GHz OPP's voltage should be increased to 0.95V.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
System counter timer is necessary as broadcast timer for cpu-idle,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MP EVK board has a GPIO LED to indicate status, add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mq-evk has a GPIO connected to AR8031 Ethernet PHY's reset pin.
Describe it in the device tree, following phy's datasheet reset duration of 10ms.
Tested booting via NFS.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm-evk has a GPIO connected to AR8031 Ethernet PHY's reset pin.
Describe it in the device tree, following phy's datasheet reset duration of 10ms.
Tested booting via NFS.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add reset control properties to the device nodes for the Display Units
on all supported RZ/G2 SoCs. Note that on these SoCs, there is only a
single reset for each pair of DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-5-geert+renesas@glider.be
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen3 SoCs. Note that on these SoCs, there is
only a single reset for each pair of DU channels.
The display nodes on R-Car V3M and V3H already had "resets" properties,
but lacked the corresponding "reset-names" properties.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-4-geert+renesas@glider.be
CONFIG_ARCH_R8A7795 was split in CONFIG_ARCH_R8A77950 and
CONFIG_ARCH_R8A77951 in commit b925adfceb ("soc: renesas: Add
ARCH_R8A7795[01] for existing R-Car H3"), so its users can be removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218112414.5591-1-geert+renesas@glider.be
Add device nodes for the CryptoCell instances on the various Renesas
R-Car Gen3 SoCs that do not have support for them yet in their device
trees (M3-W, M3-W+, M3-N, E3, D3).
The R-Car H3 device tree already supports this device.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200124133330.16121-1-geert+renesas@glider.be
The Renesas-specific "vsps" property lacks a vendor prefix.
Add a "renesas," prefix to comply with DT best practises.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20191105183504.21447-4-geert+renesas@glider.be
The r8a77970 was added with a compatible string for a different device
rather than adding the correct compatible to the driver.
Remove the unnecessary compatible which is for a different platform.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190912103734.1879-1-kieran.bingham+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The #cooling-cells property needs to be specified to allow a CPU
to be used as cooling device.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add dynamic power coefficients for all cores.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
[mb: fix commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The LS1028A has three (dual) SPI controller. These are compatible with
the ones from the LS1021A. Add the nodes.
The third controller was tested on a custom board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is only on Ethernet port and one Ethernet PHY on imx8qxp-mek.
Remove the unexisting ethphy1 port.
This fixes a run-time warning:
mdio_bus 5b040000.ethernet-1: MDIO device at address 1 is missing.
Fixes: fdea904e85 ("arm64: dts: imx: add imx8qxp mek support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The nodes with name scpsys actually implement a power-controller.
Rename the nodes to match the bindings description.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The i.MX8M Plus Media Applications Processor is part of the growing
mScale family targeting the consumer and industrial market. It brings
an effective Machine Learning and AI accelerator that enables a new
class of applications. It is built in Samsung 14LPP to achieve both
high performance and low power consumption and relies on a powerful
fully coherent core complex based on a quad core ARM Cortex-A53 cluster
and Cortex-M7 low-power coprocessor, audio digital signal processor,
machine learning and graphics accelerators.
Add the basic dtsi support for i.MX8MP.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is an external trigger timestamp fifo for PTP timer
of LS1028A. Add property fsl,extts-fifo for that.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Pinebook does not use the CSI bus on the A64. In fact it does not
use GPIO port E for anything at all. Thus the following regulators are
not used and do not need voltages set:
- ALDO1: Connected to VCC-PE only
- DLDO3: Not connected
- ELDO3: Not connected
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Properly deal with ETMv4 power management by adding the
"coresight-loses-context-with-cpu" property. Otherwise tracer
configuration is lost when CPUs enter deep idle states, resulting
in the failure of the trace session.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20200211183011.24720-1-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add sdhc instances for supporting eMMC and SD-card on sc7180.
The regulators should be in HPM state for proper functionality of
eMMC and SD-card. Updating corresponding regulators accordingly.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Link: https://lore.kernel.org/r/1578495250-10672-1-git-send-email-sbhanu@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch is to add eMMC HS200 speed mode support on ls1088ardb
whose controller and peripheral circut support such capability.
And clocks dts property is needed for driver to get peripheral
clock value used for this speed mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support for the vcnl4040 landet a while ago so add it and the
corresponding pinmux. The irq is currently unused in the driver so don't
configure it yet.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is interrupt-parent = <&gic> in root node, there is no
need set it again in node ddr-pmu@3d800000.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per devicetree specification, generic names are recommended
to be used, such as bus.
AIPS is a AHB - IP bridge bus, so we could use bus as node name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm64/boot/dts/freescale/*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm64/boot/freescale/*.dtsi
Cc: Phu Luu An <phu.luuan@nxp.com>
Cc: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Cc: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Cc: Dan Nica <dan.nica@nxp.com>
Cc: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial configuration for clocks that need default parent and rate
setting.
NoC sources from SYS PLL3, running at 600MHz. Audio AHB/IPG clks needs
to run at 400MHz for better performance.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree files for the Kontron SMARC-sAL28 board and its
carriers.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cros-ec-extcon has no reg property so remove the unit address from
the DT node to make DT compiler happy.
While here, remove the inexistent extcon-cells property from the extcon
nodes.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200207141324.3188898-1-enric.balletbo@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Arch timer stops during system suspend. Add arm,no-tick-in-suspend
property in timer.
This is a follow up for d8ec7595a0
("clocksource/drivers/arm_arch_timer: Don't assume clock runs in
suspend")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
At the moment, writing large amounts of data to the eMMC causes the device
to freeze. The symptoms vary, sometimes the device reboots immediately,
but usually it will just get stuck.
It turns out that the issue is not actually related to the eMMC:
Apparently, Samsung has made some modifications to the TrustZone firmware.
These require additional memory which is reserved at 0x85500000-0x86000000.
The downstream kernel describes this memory reservation as:
/* Additionally Reserved 6MB for TIMA and Increased the TZ app size
* by 2MB [total 8 MB ]
*/
This suggests that it is used for additional TZ apps, although the extra
memory is actually 11 MB instead of the 8 MB mentioned in the comment.
Writing to the protected memory causes the kernel to crash or freeze.
In our case, writing to the eMMC causes the disk cache to fill
the available RAM, until the kernel eventually crashes
when attempting to use the reserved memory.
Add the additional memory as reserved-memory to fix this problem.
Fixes: 1329c1ab07 ("arm64: dts: qcom: Add device tree for Samsung Galaxy A3U/A5U")
Reported-by: Michael Srba <Michael.Srba@seznam.cz>
Tested-by: Michael Srba <Michael.Srba@seznam.cz> # a3u
Tested-by: Stephan Gerhold <stephan@gerhold.net> # a5u
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191231112511.83342-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Define iommus property for QUP0 and QUP1 with the proper SID
and mask. Below SMMU global faults are seen without this during
boot and when using i2c touchscreen.
QUP0:
arm-smmu 15000000.iommu: Unexpected global fault, this could be serious
arm-smmu 15000000.iommu: GFSR 0x00000002, GFSYNR0 0x00000002, GFSYNR1 0x00000043, GFSYNR2 0x00000000
QUP1:
arm-smmu 15000000.iommu: Unexpected global fault, this could be serious
arm-smmu 15000000.iommu: GFSR 0x00000002, GFSYNR0 0x00000002, GFSYNR1 0x000004c3, GFSYNR2 0x00000000
Fixes: ba3fc64963 ("arm64: dts: sc7180: Add qupv3_0 and qupv3_1")
Tested-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20200110101802.4491-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't use the power key from the PMIC on Cheza. Disable this node so
that we don't probe the driver for this device.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200121171806.9933-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A single fix for PCI interrupt-mapping on FVP Rev C model. This is
present since the platform was added. This fix is needed to get VFIO
working correctly on this model.
-----BEGIN PGP SIGNATURE-----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=2d1/
-----END PGP SIGNATURE-----
Merge tag 'juno-fix-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARMv8 Juno/Fast Models fix for v5.6
A single fix for PCI interrupt-mapping on FVP Rev C model. This is
present since the platform was added. This fix is needed to get VFIO
working correctly on this model.
* tag 'juno-fix-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: fast models: Fix FVP PCI interrupt-map property
Link: https://lore.kernel.org/r/20200205183423.GF38466@bogus
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable mcdi-cpu and mcdi-cluster on MT8183 CPUs.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
OrangePi 3 can optionally have 8 GiB eMMC (soldered on board). Because
those pins are dedicated to eMMC exclusively, node can be added for both
variants (with and without eMMC). Kernel will then scan bus for presence
of eMMC and act accordingly.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64 contains deinterlace core, compatible to the one found in H3.
It can be used in combination with VPU unit to decode and process
interlaced videos.
Add a node for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64 contains MBUS, which is the bus used by DMA devices to access
system memory.
MBUS controller is responsible for arbitration between channels based
on set priority and can do some other things as well, like report
bandwidth used. It also maps RAM region to different address than CPU.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add the regulators for each bank on this boards.
For VCC-PL only add a comment on what regulator is used. We cannot add
the property without causing a circular dependency as the PL pins are
used to talk to the PMIC.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Now that AXP803 GPIO support is available, we can properly model
the hardware. Replace the use of GPIO0-LDO with a fixed regulator
controlled by GPIO0. This boost regulator is used to power the
(internal and external) USB ports, as well as the speakers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The output from the backlight regulator is labeled as "VBKLT" in the
schematic. Using the equation and resistor values from the schematic,
the output is approximately 18V, not 3.3V. Since the regulator in use
(SS6640STR) is a boost regulator powered by PS (battery or AC input),
which are both >3.3V, the output could not be 3.3V anyway.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL.
VCC-PC and VCC-PG are supplied by ELDO1 at 1.8v.
VCC-PD is supplied by DCDC1 (VCC-IO) at 3.3v.
VCC-PE is supplied by ALDO1, and is unused.
VCC-PL creates a circular dependency, so it is omitted for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Normally GPIO pin references are followed by a comment giving the pin
name for searchability. Add the comment here where it was missing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Boards generally reference the simplefb nodes from the SoC dtsi by
label, not by full path. simplefb_hdmi is already like this in the
Pinebook DTS. Update simplefb_lcd to match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The r_i2c node should come before r_rsb, and in any case should not
separate the axp803 node from its subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This fixed regulator has no consumers, GPIOs, or other connections.
Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Orange Pi PC2 features a GPIO button. As the button is connected to
Port L (pin PL3), it can be used as a wakeup source. Enable this.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.
It includes the following peripherals:
USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.
Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.
Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.
Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.
Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.
Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.
Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.
Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.
This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, the
front camera currently lacks a driver and a facility to share the bus
with the rear one, and the accelerometer currently lacks a DT binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Pine H64 board comes with SPI flash soldered on the board, connected
to the SPI0 pins (so it can also boot from there).
Add the required SPI flash DT node to describe this.
Unfortunately the SPI CS0 pin collides with the eMMC CMD pin, so we can't
use both eMMC and SPI flash at the same time (the first to claim the pin
would win, the other's probe routine would then fail).
To avoid losing the more useful eMMC device by chance, mark the SPI
device as "disabled" for now. A user or some U-Boot code could fix this
up if needed, for instance if no eMMC has been detected (it's socketed).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The Allwinner H6 SoC contains two SPI controllers similar to the H3/A64,
but with the added capability of 3-wire and 4-wire operation modes.
For now the driver does not support those, but the SPI registers are
fully backwards-compatible, just adding bits and registers which were
formerly reserved. So we can use the existing driver in "legacy" SPI
modes, for instance to access the SPI NOR flash soldered on the PineH64
board.
We use an H6 specific compatible string in addition to the existing H3
string, so when the driver later gains QSPI support, it should work
automatically without any DT changes.
Tested by accessing the SPI flash on a Pine H64 board (SPI0), also
connecting another SPI flash to the SPI1 header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
- New architecture features
* Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
* Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure hardware
random number generator. As well as exposing these to userspace, we
also use them as part of the KASLR seed and to seed the crng once
all CPUs have come online.
* Advertise a bunch of new instructions to userspace, including support
for Data Gathering Hint, Matrix Multiply and 16-bit floating point.
- Kexec
* Cleanups in preparation for relocating with the MMU enabled
* Support for loading crash dump kernels with kexec_file_load()
- Perf and PMU drivers
* Cleanups and non-critical fixes for a couple of system PMU drivers
- FPU-less (aka broken) CPU support
* Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck finding
a 64-bit userspace that handles this.
- Modern assembly function annotations
* Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended to
aid debuggers
- Kbuild
* Cleanup detection of LSE support in the assembler by introducing
'as-instr'
* Remove compressed Image files when building clean targets
- IP checksumming
* Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
- Hardware errata
* Work around Cortex-A55 erratum #1530923
- Shadow call stack
* Work around some issues with Clang's integrated assembler not liking
our perfectly reasonable assembly code
* Avoid allocating the X18 register, so that it can be used to hold the
shadow call stack pointer in future
- ACPI
* Fix ID count checking in IORT code. This may regress broken firmware
that happened to work with the old implementation, in which case we'll
have to revert it and try something else
* Fix DAIF corruption on return from GHES handler with pseudo-NMIs
- Miscellaneous
* Whitelist some CPUs that are unaffected by Spectre-v2
* Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
* Reserve a couple of arch-specific PROT flags that are already used by
Sparc and PowerPC and are planned for later use with BTI on arm64
* Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
* Refactoring and cleanup
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl4oY+IQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNNfRB/4p3vax0hqaOnLRvmJPRXF31B8oPlivnr2u
6HCA9LkdU5IlrgaTNOJ/sQEqJAPOPCU7v49Ol0iYw0iKL1suUE7Ikui5VB6Uybqt
YbfF5UNzfXAMs2A86TF/hzqhxw+W+lpnZX8NVTuQeAODfHEGUB1HhTLfRi9INsER
wKEAuoZyuSUibxTFvji+DAq7nVRniXX7CM7tE385pxDisCMuu/7E5wOl+3EZYXWz
DTGzTbHXuVFL+UFCANFEUlAtmr3dQvPFIqAwVl/CxjRJjJ7a+/G3cYLsHFPrQCjj
qYX4kfhAeeBtqmHL7YFNWFwFs5WaT5UcQquFO665/+uCTWSJpORY
=AIh/
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The changes are a real mixed bag this time around.
The only scary looking one from the diffstat is the uapi change to
asm-generic/mman-common.h, but this has been acked by Arnd and is
actually just adding a pair of comments in an attempt to prevent
allocation of some PROT values which tend to get used for
arch-specific purposes. We'll be using them for Branch Target
Identification (a CFI-like hardening feature), which is currently
under review on the mailing list.
New architecture features:
- Support for Armv8.5 E0PD, which benefits KASLR in the same way as
KPTI but without the overhead. This allows KPTI to be disabled on
CPUs that are not affected by Meltdown, even is KASLR is enabled.
- Initial support for the Armv8.5 RNG instructions, which claim to
provide access to a high bandwidth, cryptographically secure
hardware random number generator. As well as exposing these to
userspace, we also use them as part of the KASLR seed and to seed
the crng once all CPUs have come online.
- Advertise a bunch of new instructions to userspace, including
support for Data Gathering Hint, Matrix Multiply and 16-bit
floating point.
Kexec:
- Cleanups in preparation for relocating with the MMU enabled
- Support for loading crash dump kernels with kexec_file_load()
Perf and PMU drivers:
- Cleanups and non-critical fixes for a couple of system PMU drivers
FPU-less (aka broken) CPU support:
- Considerable fixes to support CPUs without the FP/SIMD extensions,
including their presence in heterogeneous systems. Good luck
finding a 64-bit userspace that handles this.
Modern assembly function annotations:
- Start migrating our use of ENTRY() and ENDPROC() over to the
new-fangled SYM_{CODE,FUNC}_{START,END} macros, which are intended
to aid debuggers
Kbuild:
- Cleanup detection of LSE support in the assembler by introducing
'as-instr'
- Remove compressed Image files when building clean targets
IP checksumming:
- Implement optimised IPv4 checksumming routine when hardware offload
is not in use. An IPv6 version is in the works, pending testing.
Hardware errata:
- Work around Cortex-A55 erratum #1530923
Shadow call stack:
- Work around some issues with Clang's integrated assembler not
liking our perfectly reasonable assembly code
- Avoid allocating the X18 register, so that it can be used to hold
the shadow call stack pointer in future
ACPI:
- Fix ID count checking in IORT code. This may regress broken
firmware that happened to work with the old implementation, in
which case we'll have to revert it and try something else
- Fix DAIF corruption on return from GHES handler with pseudo-NMIs
Miscellaneous:
- Whitelist some CPUs that are unaffected by Spectre-v2
- Reduce frequency of ASID rollover when KPTI is compiled in but
inactive
- Reserve a couple of arch-specific PROT flags that are already used
by Sparc and PowerPC and are planned for later use with BTI on
arm64
- Preparatory cleanup of our entry assembly code in preparation for
moving more of it into C later on
- Refactoring and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (73 commits)
arm64: acpi: fix DAIF manipulation with pNMI
arm64: kconfig: Fix alignment of E0PD help text
arm64: Use v8.5-RNG entropy for KASLR seed
arm64: Implement archrandom.h for ARMv8.5-RNG
arm64: kbuild: remove compressed images on 'make ARCH=arm64 (dist)clean'
arm64: entry: Avoid empty alternatives entries
arm64: Kconfig: select HAVE_FUTEX_CMPXCHG
arm64: csum: Fix pathological zero-length calls
arm64: entry: cleanup sp_el0 manipulation
arm64: entry: cleanup el0 svc handler naming
arm64: entry: mark all entry code as notrace
arm64: assembler: remove smp_dmb macro
arm64: assembler: remove inherit_daif macro
ACPI/IORT: Fix 'Number of IDs' handling in iort_id_map()
mm: Reserve asm-generic prot flags 0x10 and 0x20 for arch use
arm64: Use macros instead of hard-coded constants for MAIR_EL1
arm64: Add KRYO{3,4}XX CPU cores to spectre-v2 safe list
arm64: kernel: avoid x18 in __cpu_soft_restart
arm64: kvm: stop treating register x18 as caller save
arm64/lib: copy_page: avoid x18 register in assembler code
...
- Add DMA nodes for am65x and j721e
- Add McASP nodes for am65x and j721e, showcasing the DMA usage
- Add CAL node for am65x
- Add OV5640 camera support for am65x
-----BEGIN PGP SIGNATURE-----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=dL57
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-soc-for-v5.6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC family changes for 5.6, part 2.
- Add DMA nodes for am65x and j721e
- Add McASP nodes for am65x and j721e, showcasing the DMA usage
- Add CAL node for am65x
- Add OV5640 camera support for am65x
* tag 'ti-k3-soc-for-v5.6-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
arm64: dts: ti: k3-am65-main Add CAL node
arm64: dts: ti: k3-j721e-main: Add McASP nodes
arm64: dts: ti: k3-am654-main: Add McASP nodes
arm64: dts: ti: k3-j721e: DMA support
arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
arm64: dts: ti: k3-am65: DMA support
arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
Link: https://lore.kernel.org/r/83546942-6215-9c3a-16cd-be7e7c000c0e@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the OV5640 CSI camera:
- add the OV5640 nodes
- add the CAL node linkage
- enable CAL node
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add CAL dtsi node for AM654 device. Including proper power-domains and
clock properties.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the nodes for McASP 0-11 and keep them disabled because several
required properties are not present as they are board specific.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the nodes for McASP 0-2 and keep them disabled because several
required properties are not present as they are board specific.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the ringacc and udmap nodes for main and mcu NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Secure proxy (NAVSS0_SEC_PROXY0) and smmu (NAVSS0_TCU) is part of the
Navigator Subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
NAVSS is a subsystem containing different IPs, it is not really a bus.
Change the compatible from "simple-bus" to "simple-mfd" to reflect that.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
On am654 the MAIN NAVSS base address was 0x30800000, but in j721e it is
at 0x30000000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the ringacc and udmap nodes for main and mcu NAVSS.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Secure proxy (NAVSS0_SEC_PROXY0) is part of the Navigator Subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
NAVSS is a subsystem containing different IPs, it is not really a bus.
Change the compatible from "simple-bus" to "simple-mfd" to reflect that.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The interrupt map for the FVP's PCI node is missing the
parent-unit-address cells for each of the INTx entries, leading to the
kernel code failing to parse the entries correctly.
Add the missing zero cells, which are pretty useless as far as the GIC
is concerned, but that the spec requires. This allows INTx to be usable
on the model, and VFIO to work correctly.
Fixes: fa083b99eb ("arm64: dts: fast models: Add DTS fo Base RevC FVP")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
- Switch from fixed to firmware based clock driver
- Wire power domain driver
- Wire all ina226 chips through IIO and IIO hwmon drivers
- Add missing dr_mode property to usb nodes
- Use gpio-line-names property instead of comments
- Use clock-output-names for si570 differentiation
- Minor DT fixes
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXibMLgAKCRDKSWXLKUoM
IQW6AJ9Szg4yizku9Q6oi+yrR6L3eRxnyACcDiM4EeKIvrlK19cYVnd/58ENPs8=
=k6/g
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-dt-for-v5.6' of https://github.com/Xilinx/linux-xlnx into arm/dt
arm64: dts: zynqmp: DT changes for v5.6
- Switch from fixed to firmware based clock driver
- Wire power domain driver
- Wire all ina226 chips through IIO and IIO hwmon drivers
- Add missing dr_mode property to usb nodes
- Use gpio-line-names property instead of comments
- Use clock-output-names for si570 differentiation
- Minor DT fixes
* tag 'zynqmp-dt-for-v5.6' of https://github.com/Xilinx/linux-xlnx: (21 commits)
arm64: zynqmp: Add label property to all ina226 on zcu106
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu106
arm64: zynqmp: Add label property to all ina226 on zcu102
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu102
arm64: zynqmp: Add label property to all ina226 on zcu111
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu111
arm64: zynqmp: Enable iio-hwmon for ina226 on zcu100
arm64: zynqmp: Setup default number of chipselects for zcu100
arm64: zynqmp: Remove broken-cd from zcu100-revC
arm64: zynqmp: Fix the si570 clock frequency on zcu111
arm64: zynqmp: Setup clock-output-names for si570 chips
arm64: zynqmp: Turn comment to gpio-line-names
arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104
arm64: zynqmp: Remove addition number in node name
arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
arm64: dts: xilinx: Add the power nodes for zynqmp
arm64: dts: xilinx: Remove dtsi for fixed clock
arm64: dts: xilinx: Add the clock nodes for zynqmp
arm64: zynqmp: Add dr_mode property to usb node
arm64: dts: zynqmp: Use decimal values for drm-clock properties
...
Link: https://lore.kernel.org/r/c70d2efa-9ee2-a764-5248-0e5bfbf29f8a@monstr.eu
Signed-off-by: Olof Johansson <olof@lixom.net>
Since v4.3-rc1 commit 0723c05fb7 ("arm64: enable more compressed
Image formats"), it is possible to build Image.{bz2,lz4,lzma,lzo}
AArch64 images. However, the commit missed adding support for removing
those images on 'make ARCH=arm64 (dist)clean'.
Fix this by adding them to the target list.
Make sure to match the order of the recipes in the makefile.
Cc: stable@vger.kernel.org # v4.3+
Fixes: 0723c05fb7 ("arm64: enable more compressed Image formats")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Will Deacon <will@kernel.org>
accross multiple socs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl4k5D4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgfEbCACOCZhDKEttjrJckHExJzyEm+NThYTy4Mmt
FwKS10w3/Fp9Z+Pc7fZk/e1QZ6AlEQPjmy+Ls1r7D7MrkotmPy6YRI6R9OFoj/aw
eUCeo+plJUl2ij8oGgHNnWq6DJEm9cXcmCILuk8K3aj51fWMXH30L0F70lGxAuYb
G1Ta3lnZ22Yc46ie6rQuTU9xtpv2Oy7gtPnZ2uYPEs9T8GFHH/frnaJIyk0SaU4k
n7vWajLqoASDawZJ162+Tq2xtUpNF8CWdYTwtHlheVEC28g9H8f+XX+66x+plrGe
t0Prg62VWUaEn6w80JILxYwPEXh1eHXY7reM/bGwoIW+9U0UtxMX
=8p9R
-----END PGP SIGNATURE-----
Merge tag 'v5.6-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
DSI display for px30 evaluation board and a number of cleanups
accross multiple socs.
* tag 'v5.6-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Kill off "simple-panel" compatibles
arm64: dts: rockchip: rename dwmmc node names to mmc
arm64: dts: rockchip: hook up the px30-evb dsi display
arm64: dts: rockchip: Enable sdio0 and uart0 on rk3399-roc-pc-mezzanine
arm64: dts: rockchip: add reg property to brcmf sub-nodes
arm64: dts: rockchip: fix dwmmc clock name for rk3308
arm64: dts: rockchip: fix dwmmc clock name for px30
Link: https://lore.kernel.org/r/7641353.lIegmeFAIi@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
Current dts files with 'dwmmc' nodes are manually verified.
In order to automate this process rockchip-dw-mshc.txt
has to be converted to yaml. In the new setup
rockchip-dw-mshc.yaml will inherit properties from
mmc-controller.yaml and synopsys-dw-mshc-common.yaml.
'dwmmc' will no longer be a valid name for a node,
so change them all to 'mmc'
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200115185244.18149-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Link: https://lore.kernel.org/r/20200117190305.5257-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Texas Instruments K3 SoC family changes for 5.6
- Add missing power domains for smmu for J721e
- Add I2C, ADC, OSPI and UFS nodes for J721e
- Add OSPI and MCU syscon nodes for am65x
- Add IRQ line for GPIO expander on am65x
* tag 'ti-k3-soc-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-j721e-main: Add missing power-domains for smmu
arm64: dts: ti: k3-am65-mcu: add system control module node
arm64: dts: k3-am654-base-board: Add IRQ line for GPIO expander
arm64: dts: ti: k3-am65: Add OSPI DT node
arm64: dts: ti: k3-j721e: Add DT nodes for few peripherials
Link: https://lore.kernel.org/r/c5b74bfc-f2f0-1b72-4a3c-4c1d478a023a@ti.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The Denali NAND controller IP has separate reset control for the
controller core and registers.
Add the reset-names, and one more phandle accordingly. This is the
approved DT-binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add power-domains entry for smmu, so that the it is accessible as long
as the driver is active. Without this device shutdown is throwing the
below warning:
"[ 44.736348] arm-smmu-v3 36600000.smmu: failed to clear cr0"
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The MCU System control module support is added to the device tree to allow
drivers to access to their System control module registers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add IRQ line for IO expander present on wkup_i2c bus on AM654 EVM
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM654 SoC has two Cadence OSPI controller instances under Flash
subsystem (FSS). Add DT nodes for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
- add dynamic power coefficient to the cpu clusters
- add jpeg decoder node
mt8183:
- add node for the Global Command Engine (gce)
- add reset cells to the infracfg node
-----BEGIN PGP SIGNATURE-----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=d7+O
-----END PGP SIGNATURE-----
Merge tag 'v5.5-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
mt8173:
- add dynamic power coefficient to the cpu clusters
- add jpeg decoder node
mt8183:
- add node for the Global Command Engine (gce)
- add reset cells to the infracfg node
* tag 'v5.5-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: add reset-cells in infracfg
arm64: dts: mt8173: add Mediatek JPEG Codec
arm64: dts: add gce node for mt8183
arm64: dts: mt8173: Add dynamic power node.
Link: https://lore.kernel.org/r/46c1a244-3f74-8069-6600-8ced02775677@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
It's fairly big this time, but the highlights are:
- Enable cpufreq and CPU thermal throttling on the A64
- CLK_CPUX macro usage removed (changed from first pull request)
- CSI0 support on the R40
- CSI1 support on the A10 and A20
- SPI support on the R40
- PMU support on the H3, H5, H6 and R40
- MIPI-DSI support on the A64
- PWM support on the H6
- Thermal sensor on the A64, A83t, H3, H5, H6 and R40
- More DT schemas fixes and conversions
- New boards: LibreComputer ALL-H5-CC H5, LibreComputer ALL-H3-IT H5,
Pine64 H64 Model B, Neutis N5H3
-----BEGIN PGP SIGNATURE-----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=1h4A
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
This is our usual set of DT patches for the Allwinner SoCs.
It's fairly big this time, but the highlights are:
- Enable cpufreq and CPU thermal throttling on the A64
- CLK_CPUX macro usage removed (changed from first pull request)
- CSI0 support on the R40
- CSI1 support on the A10 and A20
- SPI support on the R40
- PMU support on the H3, H5, H6 and R40
- MIPI-DSI support on the A64
- PWM support on the H6
- Thermal sensor on the A64, A83t, H3, H5, H6 and R40
- More DT schemas fixes and conversions
- New boards: LibreComputer ALL-H5-CC H5, LibreComputer ALL-H3-IT H5,
Pine64 H64 Model B, Neutis N5H3
* tag 'sunxi-dt-for-5.6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (52 commits)
arm64: dts: allwinner: a64: enable DVFS
arm64: dts: allwinner: a64: add dtsi with CPU operating points
arm64: dts: allwinner: a64: add cooling maps and thermal tripping points
arm64: dts: allwinner: a64: add CPU clock to CPU0-3 nodes
arm64: dts: allwinner: sun50i-a64: Use macros for newly exported clocks
ARM: dts: sunxi: Use macros for references to CCU clocks
arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board
ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes
arm64: dts: allwinner: a64: pinebook: Fix lid wakeup
ARM: dts: sun8i: r40: Add device node for CSI0
ARM: dts: sun7i: Add CSI1 controller and pinmux options
ARM: dts: sun4i: Add CSI1 controller and pinmux options
ARM: dts: sunxi: Add missing LVDS resets and clocks
ARM: dts: sun8i: r40: Use tcon top clock index macros
ARM: dts: sun8i: R40: Add PMU node
ARM: dts: sun8i: R40: Upgrade GICC reg size to 8K
arm64: dts: allwinner: h6: Add thermal sensor and thermal zones
ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board
arm64: dts: allwinner: a64: Add MIPI DSI pipeline
arm64: dts: allwinner: a64: Add thermal sensors and thermal zones
...
Link: https://lore.kernel.org/r/20200113095555.GA29848@wens.csie.org
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board support: i.MX8MQ based Thor96 board, Google i.MX8MQ Phanbell
board, LX2160A based Solidrun Clearfog CX and Honeycomb boards.
- Add eLCDIF controller and missing SAI nodes for i.MX8MQ SoC.
- Add Crypto CAAM support for i.MX8MM and i.MX8MN.
- Drop unneeded "simple-bus" from anatop node on i.MX8MM and i.MX8MN.
- Drop unused/undocumented "fsl,aips-bus" and "fsl,imx8mq-aips-bus"
compatibles from i.MX8M SoCs.
- Add DDR controller nodes for i.MX8M devices.
- Add EEPROM description for imx8mq-hummingboard-pulse and
imx8mq-sr-som boards.
- Enable USB1 and TypeC support for imx8mn-evk board.
- Add FlexSPI and QSPI support for a few Layerscape SoCs and boards.
- Add External MDIO1 node and the two RGMII PHYs connected on LX2160A.
- Add missing SAI devices and set SAIs into async mode on LS1028A.
- Other random device additions and enhancement for various platforms.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl4b4EYUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6Iwwf/ZqkWN7e4Am8MFMbw4aJ4WLMes1M5
pHWEl/vxLmOdrzY45pyLjxarkXlzEE/Q4iS0/k9g4FSjj2BCOzFjlJAskTPGF7Jh
YL02N32xPpsWHxJ04wX+VqZYrNkPH3ywpfgfOQzW9JWIs/Jz0PGB65SuniuHuhdr
Y1twDz1sVLVdMpp6dlfPtMFxRMydvjkvlXrk7HzFuyGbxeJnGzhWa4rUlVcQoKwm
+v/Hcn7B2CQgBzFgRQJUXEPntWFVPSB7c1nlx3iH4HHwGi14k5QbAfn6xBLyOwXQ
QN3MCpY4n2ankaJ5D3zBQ5kCt17EOGUOLaW4VC5RpSUKhafSZV4din8cWA==
=JSDg
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.6:
- New board support: i.MX8MQ based Thor96 board, Google i.MX8MQ Phanbell
board, LX2160A based Solidrun Clearfog CX and Honeycomb boards.
- Add eLCDIF controller and missing SAI nodes for i.MX8MQ SoC.
- Add Crypto CAAM support for i.MX8MM and i.MX8MN.
- Drop unneeded "simple-bus" from anatop node on i.MX8MM and i.MX8MN.
- Drop unused/undocumented "fsl,aips-bus" and "fsl,imx8mq-aips-bus"
compatibles from i.MX8M SoCs.
- Add DDR controller nodes for i.MX8M devices.
- Add EEPROM description for imx8mq-hummingboard-pulse and
imx8mq-sr-som boards.
- Enable USB1 and TypeC support for imx8mn-evk board.
- Add FlexSPI and QSPI support for a few Layerscape SoCs and boards.
- Add External MDIO1 node and the two RGMII PHYs connected on LX2160A.
- Add missing SAI devices and set SAIs into async mode on LS1028A.
- Other random device additions and enhancement for various platforms.
* tag 'imx-dt64-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (35 commits)
arm64: dts: imx8mn: Memory node should be in board DT
arm64: dts: imx8mm: Memory node should be in board DT
arm64: dts: imx8mn: add crypto node
arm64: dts: imx8mq-hummingboard-pulse: add eeprom description
arm64: dts: imx8mq-sr-som: add eeprom description
arm64: dts: ls208xa: Update qspi node properties for LS2088ARDB
arm64: dts: freescale: Add devicetree support for Thor96 board
arm64: dts: imx8mq-librem5-devkit: add accelerometer and gyro sensor
arm64: dts: imx8mm: Add Crypto CAAM support
arm64: dts: freescale: add initial support for Google i.MX 8MQ Phanbell
arm64: dts: ls1028a-rdb: enable emmc hs400 mode
arm64: dts: ls1028a: Update edma compatible to fit eDMA driver
arm64: dts: imx8m: drop "fsl,aips-bus" and "fsl,imx8mq-aips-bus"
arm64: dts: imx8mm: Add missing mux options for UART1 and UART2 signals
arm64: dts: lx2160a: add dts for CEX7 platforms
arm64: dts: lx2160a: add emdio2 node
arm64: dts: ls1028a: put SAIs into async mode
arm64: dts: ls1028a: add missing sai nodes
arm64: dts: imx8mn-evk: enable usb1 and typec support
arm64: dts: imx8mn: Remove setting for IMX8MN_CLK_USB_CORE_REF
...
Link: https://lore.kernel.org/r/20200113034006.17430-5-shawnguo@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
These patches do some cleanup to existing nodes, add the memory
subsystem on Tegra186 and Tegra194 as well as the FUSE and APB MISC
nodes on Tegra194. There are also a few additions to the Jetson Nano
device tree to enable additional features and the force recovery
button on the Jetson AGX Xavier now produces a key code that is
actually valid. Finally, an alias is added for the Ethernet card on
Jetson TX2 to allow firmware to find it and pass a MAC address via
device tree.
-----BEGIN PGP SIGNATURE-----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=lD4r
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.6-rc1
These patches do some cleanup to existing nodes, add the memory
subsystem on Tegra186 and Tegra194 as well as the FUSE and APB MISC
nodes on Tegra194. There are also a few additions to the Jetson Nano
device tree to enable additional features and the force recovery
button on the Jetson AGX Xavier now produces a key code that is
actually valid. Finally, an alias is added for the Ethernet card on
Jetson TX2 to allow firmware to find it and pass a MAC address via
device tree.
* tag 'tegra-for-5.6-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Allow bootloader to configure Ethernet MAC on Jetson TX2
arm64: tegra: Redefine force recovery key on Jetson AGX Xavier
arm64: tegra: Enable SDIO on Jetson Nano M.2 Key E
arm64: tegra: Enable PWM fan on Jetson Nano
arm64: tegra: Add fuse/apbmisc node on Tegra194
arm64: tegra: Make XUSB node consistent with the rest
arm64: tegra: Add the memory subsystem on Tegra194
arm64: tegra: Add external memory controller on Tegra186
arm64: tegra: Add interrupt for memory controller on Tegra186
arm64: tegra: Rename EMC on Tegra132
arm64: tegra: Let the EMC hardware use the EMC clock
Link: https://lore.kernel.org/r/20200111003553.2411874-7-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We want to specify per-device firmware-name, so move the zap node into
the .dts file for individual boards/devices. This lets us get rid of
the /delete-node/ for cheza, which does not use zap.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200112195405.1132288-5-robdclark@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
I missed the fact that these constants was not yet available, so hard
code their values in the dts to make the branch compile on its own.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Create the necessary display nodes to activate the Xingpeng XPP055C272
dsi display that can be found on the px30-evb.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20191209145301.5307-2-heiko@sntech.de
Include mt8183-reset.h and add reset-cells in infracfg
in dtsi file
Signed-off-by: yong.liang <yong.liang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The mezzanine board carries an E key type M.2 slot. This is
connected to USB, SDIO and UART0. Enable sdio and uart0 for use
with wlan and/or bt M.2 cards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/20200109154211.1530-1-m.reichl@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below gives this error:
rk3399-firefly.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-orangepi.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-captain.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
rk3399-khadas-edge-v.dt.yaml: dwmmc@fe310000: wifi@1:
'reg' is a required property
So fix this by adding a reg property to the brcmf sub node.
Also add #address-cells and #size-cells to prevent more warnings.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110142128.13522-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below gives this error:
rk3308-evb.dt.yaml: dwmmc@ff480000: clock-names:2:
'ciu-drive' was expected
'ciu-drv' is not a valid dwmmc clock name,
so fix this by changing it to 'ciu-drive'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110161200.22755-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below gives this error:
px30-evb.dt.yaml: dwmmc@ff390000: clock-names:2:
'ciu-drive' was expected
'ciu-drv' is not a valid dwmmc clock name,
so fix this by changing it to 'ciu-drive'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200110161200.22755-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add CPU regulator and operating points for all the A64-based boards
that are currently supported to enable DVFS.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add operating points for A64. These are taken from FEX file from BSP
for A64.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add cooling maps and thermal tripping points to prevent CPU overheating when
running at the highest frequency. Tripping points are taken from A33 dts since
A64 user manual doesn't mention when we should start throttling.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add CPU clock to the CPU nodes since it is a prerequisite for enabling
DVFS.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
[wens@csie.org: Replace CLK_CPUX macro with raw number]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
carrier board, separate versions for the two rockpro64 hardware revisions
which switched a pin between revisions. The rockpro64 also got
bluetooth support now.
The px30 got a lot of attention with dsi, gpu and thermal support.
Similarly the rk3399-roc-pc board also got attention with mtd flash,
sdr104 mode, hdmi sound, gpu and a lot of other smaller improvements.
Other than that there is a new gpu-cooling device for rk3399 a cpu
idle-state for rk3328 and more small improvements across a number
of boards.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl4Xm7MQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgXPbB/4/iuGhWfydiiB6Mrmeifzlt+Ch7Hm5IJBA
03f8FiHbGkW1Tlh1buw6t9BDKI0XKNqD94MU0pya4yDB7baFaH1GEk8S4/mbEAuE
OZnWM0jzQ40b/1JmwRCw0PL2NTFHwlE+SSHnBJ4EW/OnOsCYUSz8+Aq33fMwdsPA
Dm9gxAeeHsBJTxk26cxLrGePB5vYXltGwazklkKkU5scV75sfJu1xcRKcnVp71sH
4j33aWi19GWo2YkW6RGXzTgiXoFPR+PgzfU337KTqq6A5oSIybH9g2WUnYyAxi8R
tJKxiOBSBeGIrIRxMWtw8g9VxohJwzHfi9y4XO1VwzLpl/SQf3mb
=iCh7
-----END PGP SIGNATURE-----
Merge tag 'v5.6-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New boards are the Radxa Rock Pi N10 using the VMARC SOM and Dalang
carrier board, separate versions for the two rockpro64 hardware revisions
which switched a pin between revisions. The rockpro64 also got
bluetooth support now.
The px30 got a lot of attention with dsi, gpu and thermal support.
Similarly the rk3399-roc-pc board also got attention with mtd flash,
sdr104 mode, hdmi sound, gpu and a lot of other smaller improvements.
Other than that there is a new gpu-cooling device for rk3399 a cpu
idle-state for rk3328 and more small improvements across a number
of boards.
* tag 'v5.6-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (37 commits)
arm64: dts: rockchip: Enable mp8859 regulator on rk3399-roc-pc
arm64: dts: rockchip: rk3399-hugsun-x99: remove supports-sd and supports-emmc options
arm64: dts: rockchip: rk3399-firefly: remove num-slots from &sdio0 node
arm64: dts: rockchip: Add PX30 LVDS
arm64: dts: rockchip: add dsi controller for px30
arm64: dts: rockchip: Add PX30 DSI DPHY
arm64: dts: rockchip: Add RK3328 idle state
arm64: dts: rockchip: remove identical &uart0 node from rk3368-lion-haikou
arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
ARM: dts: rockchip: Add Radxa Dalang Carrier board
arm64: dts: rockchip: Add VMARC RK3399Pro SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N10 binding
arm64: dts: rockchip: hook up bluetooth at uart0 on rockpro64
arm64: dts: rockchip: enable wifi module at sdio0 on rockpro64
arm64: dts: rockchip: split rk3399-rockpro64 for v2 and v2.1 boards
arm64: dts: rockchip: enable the gpu on px30-evb
arm64: dts: rockchip: add the gpu for px30
dt-bindings: gpu: mali-bifrost: Add Rockchip PX30
arm64: dts: rockchip: Add GPU cooling device for RK3399
arm64: dts: rockchip: Add regulators for PCIe for Radxa Rock Pi 4 board
...
Link: https://lore.kernel.org/r/5115625.yBEeHQkg2z@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add remote control map name of the IR device for the hi3798cv200 poplar board
- Correct the PCIe bus range setting for the hi3798cv200
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+4YO
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-5.6' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for 5.6
- Add remote control map name of the IR device for the hi3798cv200 poplar board
- Correct the PCIe bus range setting for the hi3798cv200
* tag 'hisi-arm64-dt-for-5.6' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi3798cv200: correct PCIe 'bus-range' setting
arm64: dts: hi3798cv200-poplar: add linux,rc-map-name for IR
Link: https://lore.kernel.org/r/5E169EDE.8020809@hisilicon.com
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl4XkqoQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgfPdCACArEwY6eMQspCf9akFXt1splXKKk6eygtZ
vKduoK0A0CGmYF3XGo0umk7KX5b2NZdvFbUiFzBv/zyrBL05yY86KIRUx+qCh8En
HIKDDL8grI4yyJftvcQeLo52B4Jw1SfP91MFSgowmOkTVlqlVwXDpn2cs/ShRD78
Z0fatPZ8XnHeiIpcAcsJLPlZXPDNORPkDv/ePBLepmT5CgQJWsZfeULNK8xP5Z4P
tJLyQPWM2Hz9tOlECVIGwNoIYlchN2erhy35UNstUIkew6MCOM2L4LfkV7jJ1b49
rZ1qlYlq+fVV+Ut+fNAusjK2Nn2Zh4zQ3bRd1qPxmeXS3SUstHJo
=mlvF
-----END PGP SIGNATURE-----
Merge tag 'v5.5-rockchip-dtsfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
A fix for the Beelink A1 IR receiver setting the correct polarity.
* tag 'v5.5-rockchip-dtsfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix IR on Beelink A1
Link: https://lore.kernel.org/r/2054603.JKFSmqfO19@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
Claudiu Manoil