This patch describes 3 additional interrupts per PPv2 port. Those
interrupts will be used later in future versions of the Marvell PPv2
driver, and now the device tree description matches the hardware
capabilities.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch changes the PPv2 IRQ names in the CP110 device tree to match
a corresponding change in the Marvell PPv2 driver. The reason this was
updated is the IRQ where names after Tx/Rx interrupts, but this is not
true and can be configured. A following patch will add more of them and
the names wouldn't make sense.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The SolidRun Clearfog GT-8K is based on Marvell Armada 8040 SoC.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The following devices were tested with this DT on top of kernel
v4.19-rc4:
* 1GB Ethernet WAN
* 4 ports 1GB Ethernet switch (2.5GB uplink)
* SFP port
* SATA on CON3 PCIe slot
* USB3 type A port
* SD card and eMMC
* 2 LEDs
* 2 push buttons
[gregory: fix block comment alignement]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
DSI controllers are also the hosts of their dsi bus and therefore contain
nodes describing the attached panels with their reg properties containing
the virtual ids.
The dsi controller nodes on rk3399 lacked the #address-cells and #size-cells
for these subnodes, so add them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
that supports the JEDEC read-ID command.
This patch enables the SPI controller and adds a device node
for the flash chip using the generic "jedec,spi-nor" comaptible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockpro64 is a rockchip RK3399 based board from pine64.org.
This patch adds basic device node support for Rockpro64 board and make it able
to bring up.
Peripheral Works
- Sdcard
- USB 2.0, 3.0
- Leds
- Ethernet
- Debug console
Not working:
- USB Type-C
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Acked-by: Deepak Das <Deepak_Das@mentor.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Based on a similar patch of the R8A7796 device tree
by Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds LVDS decoder, HDMI encoder and connector for the Draak board.
The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Draak
board, hook them up in DT.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the LVDS decoder, HDMI encoder, VGA encoder and HDMI and VGA
connectors, and wire up the display-related nodes with clocks, pinmux
and regulators.
The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Ebisu
board, hook them up in DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[uli: moved lvds* into the soc node, added PM domains, resets]
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Try to add basic DT support for the Amlogic's Meson-G12A S905D2 SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
dtc has new checks for I2C and SPI buses. Fix the SPI bus node names
and warnings in unit-addresses.
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dtb: Warning (i2c_bus_reg): /soc/i2c@2180000/eeprom@57: I2C bus unit address format error, expected "53"
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dtb: Warning (i2c_bus_reg): /soc/i2c@2180000/eeprom@56: I2C bus unit address format error, expected "52"
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The R8A77990 (E3) platform has one RGB output and two LVDS outputs
connected to the DU. Add the DT nodes for the DU, LVDS encoders and
supporting VSP and FCP.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch is adding communication layer with firmware.
Firmware driver provides an interface to firmware APIs.
Interface APIs can be used by any driver to communicate to
PMUFW(Platform Management Unit). All requests go through ATF.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reverts commit 46053c7368.
This change breaks architectures setting up dma_ops in their own magic
way and not using arch_setup_dma_ops, so revert it.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Clang warns that if the default case is taken, ret will be
uninitialized.
./arch/arm64/include/asm/percpu.h:196:2: warning: variable 'ret' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]
default:
^~~~~~~
./arch/arm64/include/asm/percpu.h:200:9: note: uninitialized use occurs
here
return ret;
^~~
./arch/arm64/include/asm/percpu.h:157:19: note: initialize the variable
'ret' to silence this warning
unsigned long ret, loop;
^
= 0
This warning appears several times while building the erofs filesystem.
While it's not strictly wrong, the BUILD_BUG will prevent this from
becoming a true problem. Initialize ret to 0 in the default case right
before the BUILD_BUG to silence all of these warnings.
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Commit a7eb26392b ("arm64: dts: broadcom: Add reference to Compute
Module IO Board V3") adds the bcm2837-rpi-cm3-io3.dts file as a target
in the Makefile, rather than the .dtb name. This will skip the
generation of the .dtb file at compile time and will fail the dtbs_install
target.
Fixes: a7eb26392b ("arm64: dts: broadcom: Add reference to Compute Module IO Board V3")
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable integrated NIC driver(hns3) for hisilicon SoCs
- Enable PCIe Port bus to support some PCIe features like
AER, hotplug, PME and DPC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Gn5v
-----END PGP SIGNATURE-----
Merge tag 'hisi-defconfig-for-4.20' of git://github.com/hisilicon/linux-hisi into next/defconfig
ARM64: hisilicon: defconfig updates for 4.20
- Enable integrated NIC driver(hns3) for hisilicon SoCs
- Enable PCIe Port bus to support some PCIe features like
AER, hotplug, PME and DPC
* tag 'hisi-defconfig-for-4.20' of git://github.com/hisilicon/linux-hisi:
arm64: defconfig: Enable PCIEPORTBUS
arm64: defconfig: enable HiSilicon HNS3 driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the bananapi R64 (BPI-R64) development board from
BIPAI KEJI. Detailed hardware information for BPI-R64 which could be
found on http://wiki.banana-pi.org/Banana_Pi_BPI-R64
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix ram size to 512 megabytes and sort nodes in alphabetical order.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a built-in bluetooth 5 support for MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add device tree entries for timer, ARM CCI-400 and its PMU.
Otherwise, we add a cortex-a53-pmu node to enable hw perfevents.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Now that deliberate writes to swapper_pg_dir are made via the fixmap, we
can defend against errant writes by moving it into the rodata section.
Since tramp_pg_dir and reserved_ttbr0 must be at a fixed offset from
swapper_pg_dir, and are not modified at runtime, these are also moved
into the rodata section. Likewise, idmap_pg_dir is not modified at
runtime, and is moved into rodata.
Signed-off-by: Jun Yao <yaojun8558363@gmail.com>
Reviewed-by: James Morse <james.morse@arm.com>
[Mark: simplify linker script, commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Once swapper_pg_dir is in the rodata section, it will not be possible to
modify it directly, but we will need to modify it in some cases.
To enable this, we can use the fixmap when deliberately modifying
swapper_pg_dir. As the pgd is only transiently mapped, this provides
some resilience against illicit modification of the pgd, e.g. for
Kernel Space Mirror Attack (KSMA).
Signed-off-by: Jun Yao <yaojun8558363@gmail.com>
Reviewed-by: James Morse <james.morse@arm.com>
[Mark: simplify ifdeffery, commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since the address of swapper_pg_dir is fixed for a given kernel image,
it is an attractive target for manipulation via an arbitrary write. To
mitigate this we'd like to make it read-only by moving it into the
rodata section.
We require that swapper_pg_dir is at a fixed offset from tramp_pg_dir
and reserved_ttbr0, so these will also need to move into rodata.
However, swapper_pg_dir is allocated along with some transient page
tables used for boot which we do not want to move into rodata.
As a step towards this, this patch separates the boot-time page tables
into a new init_pg_dir, and reduces swapper_pg_dir to the single page it
needs to be. This allows us to retain the relationship between
swapper_pg_dir, tramp_pg_dir, and swapper_pg_dir, while cleanly
separating these from the boot-time page tables.
The init_pg_dir holds all of the pgd/pud/pmd/pte levels needed during
boot, and all of these levels will be freed when we switch to the
swapper_pg_dir, which is initialized by the existing code in
paging_init(). Since we start off on the init_pg_dir, we no longer need
to allocate a transient page table in paging_init() in order to ensure
that swapper_pg_dir isn't live while we initialize it.
There should be no functional change as a result of this patch.
Signed-off-by: Jun Yao <yaojun8558363@gmail.com>
Reviewed-by: James Morse <james.morse@arm.com>
[Mark: place init_pg_dir after BSS, fold mm changes, commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In subsequent patches we'll use a transient pgd during the primary cpu's
boot process. To make this work while allowing secondary cpus to use the
swapper_pg_dir, we need to pass the relevant TTBR1 pgd as a parameter
to __enable_mmu().
This patch updates __enable__mmu() to take this as a parameter, updating
callsites to pass swapper_pg_dir for now.
There should be no functional change as a result of this patch.
Signed-off-by: Jun Yao <yaojun8558363@gmail.com>
Reviewed-by: James Morse <james.morse@arm.com>
[Mark: simplify assembly, clarify commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Enable all necessary device tree nodes and add connector node to device
trees for all supported A64 boards with HDMI.
Jagan, tested on BPI-M64, OPI-Win, A64-Olinuxino, NPI-A64
Vasily, tested on pine64-lts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: squash all board patches altogether and change supply name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner A64 have a display pipeline with 2 mixers/TCONs, the first
TCON is connected to LCD and the second is to HDMI.
The HDMI controller/PHY pair is similar to the one on H3/H5.
Add all required device tree nodes of the display pipeline, including
the TCON0 LCD one and the TCON1 HDMI one.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: refactor commit message and add 1st pipeline]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Whilst the symmetry of deferring to the existing sync callback in
__iommu_map_page() is nice, taking a round-trip through
iommu_iova_to_phys() is a pretty heavyweight way to get an address we
can trivially compute from the page we already have. Tweaking it to just
perform the cache maintenance directly when appropriate doesn't really
make the code any more complicated, and the runtime efficiency gain can
only be a benefit.
Furthermore, the sync operations themselves know they can only be
invoked on a managed DMA ops domain, so can use the fast specific domain
lookup to avoid excessive manipulation of the group refcount
(particularly in the scatterlist cases).
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
fsl-mc bus support the new iommu-map property. Comply to this binding
for fsl_mc bus.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Describe TPU in the R8A779{7|8}0 device trees.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 SoCs need to enable/deassert clocks/resets of both usb 2.0
host (included phy) and peripheral. Otherwise, other side device
cannot work correctly. So, this patch revises properties of clocks
and resets. After that, each device driver can enable/deassert
clocks/resets by its self.
Notes:
- To work the renesas_usbhs driver correctly when host side drivers
are disabled and the renesas_usbhs driver doesn't have multiple
clock management, this patch doesn't change the order of the clocks
property in each hsusb node.
- This patch doesn't have any side-effects even if the renesas_usbhs
driver doesn't have reset_control and multiple clock management.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Turn the macro into an inline, move it to blk.h and simplify the
arch hooks a bit.
Also rename the function to biovec_phys_mergeable as there is no need
to shout.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
MMC host controller bindings and MMC core defines card detect pin as
active low. Therefore there is no point to invert it twice.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
For contiguous hugetlb, huge_ptep_set_access_flags performs a
get_clear_flush (which then flushes the TLBs) even when no change of ptes
is necessary.
Unfortunately, this behaviour can lead to back-to-back page faults being
generated when running with multiple threads that access the same
contiguous huge page.
Thread 1 | Thread 2
-----------------------------+------------------------------
hugetlb_fault |
huge_ptep_set_access_flags |
-> invalidate pte range | hugetlb_fault
continue processing | wait for hugetlb_fault_mutex
release mutex and return | huge_ptep_set_access_flags
| -> invalidate pte range
hugetlb_fault
...
This patch changes huge_ptep_set_access_flags s.t. we first read the
contiguous range of ptes (whilst preserving dirty information); the pte
range is only then invalidated where necessary and this prevents further
spurious page faults.
Fixes: d8bdcff287 ("arm64: hugetlb: Add break-before-make logic for contiguous entries")
Reported-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In the contiguous bit hugetlb break-before-make code we assume that all
hugetlb pages are young.
In fact, remove_migration_pte is able to place an old hugetlb pte so
this assumption is not valid.
This patch fixes the contiguous hugetlb scanning code to preserve young
ptes.
Fixes: d8bdcff287 ("arm64: hugetlb: Add break-before-make logic for contiguous entries")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
x0 is not callee-saved in the PCS. So there is no need to specify
-fcall-used-x0.
Clang doesn't currently support -fcall-used flags. This patch will help
building the kernel with clang.
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Tri Vo <trong@android.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It can't boot without bootargs settings on Uboot on ulcb board.
This patch adds missing default bootargs.
ulcb BSP can overwrite it by own UBoot settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This branch adds changes for the Texas Instruments AM654 SoC. Included
changes are:
- Add uart nodes
- Change address cells and size-cells of interconnect tfrom 1 to 2
- Add secure proxy instance for main domain
- Add DMSC support
-----BEGIN PGP SIGNATURE-----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=VyVP
-----END PGP SIGNATURE-----
Merge tag 'am654-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into next/dt
TI AM654 support for v4.20 merge window.
This branch adds changes for the Texas Instruments AM654 SoC. Included
changes are:
- Add uart nodes
- Change address cells and size-cells of interconnect tfrom 1 to 2
- Add secure proxy instance for main domain
- Add DMSC support
* tag 'am654-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-am6: Add Device Management Security Controller support
arm64: dts: ti: am654: Add secure proxy instance for main domain
arm64: dts: ti: am654: Add uart nodes
arm64: dts: ti: k3-am65: Change #address-cells and #size-cells of interconnect to 2
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.20, please pull the following:
- Stefan provides a reference to the Compute Module IO Board V3 such
that we can reference the arm counterpart and still build it for arm64
- Rob fixes I2C and SPI bus warnings which are going to show up with his
update to DTC scheduled for 4.20
-----BEGIN PGP SIGNATURE-----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=Ulpq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.20/devicetree-arm64' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 4.20, please pull the following:
- Stefan provides a reference to the Compute Module IO Board V3 such
that we can reference the arm counterpart and still build it for arm64
- Rob fixes I2C and SPI bus warnings which are going to show up with his
update to DTC scheduled for 4.20
* tag 'arm-soc/for-4.20/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: Fix I2C and SPI bus warnings
arm64: dts: broadcom: Add reference to Compute Module IO Board V3
Signed-off-by: Olof Johansson <olof@lixom.net>
New boards are the px30 eval board and roc-rk3399-pc.
The rk3328 got support for the one gpio controlled via the general
register files and the rk3399 finally got its idle-states defined.
And finally fixes and improvements for firefly-rk3399 (wifi),
roc-rk3328-cc (sdmmc-uhs, io-domains), rk3328-rock64 (gpio-regulator
pin fix) and rk3399-sapphire (gpio-regulator pin fix, pmic pin fix
and type-c port supply).
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAluaaskQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgTTdCACrfKOzRBY7rAmuo5abqWZGsAmbVLFmC/dG
ssxdF9uUAKS2vOV2OKu4364RZgBTXI4Ko+k4IT/mbQbAOduvlrcdHoB+a0IzSJJj
WGpFKTyt63uL9V34sLSXfJ7f0NevWXnBT54tisbvfOVHC+ysJ6MrvEiGl6eDcCkh
Hweejd/tzryFefgn4r2TClsGtew45cSo2ZO9IHNTaLSNxL2yz6r3jCwmWl3P7a8o
eBfvOllg/5FYKL1ybXs6/RJBOeowzOk9RBr9r2Q+7EGD6XsuU4W1DXc8wI57xwXP
bYP/JfQR/yGrJuX+eA6XxkMoGXu5VWSu6PFnyupIGpmJz2EG/kGL
=T4U2
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
New soc support for the px30 quad-core Cortex-A35.
New boards are the px30 eval board and roc-rk3399-pc.
The rk3328 got support for the one gpio controlled via the general
register files and the rk3399 finally got its idle-states defined.
And finally fixes and improvements for firefly-rk3399 (wifi),
roc-rk3328-cc (sdmmc-uhs, io-domains), rk3328-rock64 (gpio-regulator
pin fix) and rk3399-sapphire (gpio-regulator pin fix, pmic pin fix
and type-c port supply).
* tag 'v4.20-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add type-c port supply on rk3399-sapphire board
arm64: dts: rockchip: fix vcc_host1_5v pin assign on rk3328-rock64
arm64: dts: rockchip: add WiFi module support for Firefly-RK3399
arm64: dts: rockchip: remove dvs2 pinctrl from pmic on rk3399-sapphire
arm64: dts: rockchip: Fix VCC5V0_HOST_EN on rk3399-sapphire
arm64: dts: rockchip: re-order vcc_sys on rk3399-sapphire
arm64: dts: rockchip: add missing vop properties for px30
arm64: dts: rockchip: Add idle-states to device tree for rk3399
arm64: dts: rockchip: add sdmmc UHS support for roc-rk3328-cc
arm64: dts: rockchip: add GRF GPIO controller to rk3328
arm64: dts: rockchip: add io-domain to roc-rk3328-cc
arm64: dts: rockchip: add PX30 evaluation board devicetree
arm64: dts: rockchip: add core dtsi file for PX30 SoCs
dt-bindings: rockchip: grf: add grf and pmugrf description for px30
arm64: dts: rockchip: add support for ROC-RK3399-PC board
Signed-off-by: Olof Johansson <olof@lixom.net>
For proper working of SD cards, let's add the Card Detect GPIO property
to the common devicetree for Rock960 family boards.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree support for Rock960 board, one of the Consumer Edition
boards of the 96Boards family. This board support utilizes the common
Rock960 family board support that includes Ficus 96Board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since the same family members of Rock960 boards (Rock960 and Ficus)
share the same configuration, split out the common nodes into a common
dtsi file for reducing code duplication. The board specific nodes for
Ficus boards are then placed in corresponding board DTS file.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
Only the properties which differ between both boards are placed in the
board specific dts and the reset of the nodes are placed in common dtsi
file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds sound card node for rock64. Currently we can support
S/PDIF only. It seems the lack of codec driver of rk3328 to enable
analog audio out.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The microSD card slot in the Sapphire board is not working because of
several issues:
1.- The vmmc power supply is missing in the DTS. It is capable of 3.0V
and has a GPIO-based enable control.
2.- The vqmmc power supply can provide up to 3.3V, but it is capped in
the DTS to just 3.0V because of the vmmc capability. This results in a
conflict from the mmc driver requesting an unsupportable voltage range
from 3.3V to 3.0V (min > max) as reported in dmesg. So, extend the
range up to 3.3V. The hw should be able to stand this 0.3V tolerance.
See mmc_regulator_set_vqmmc in drivers/mmc/core/core.c.
3.- The card detect signal is non-working. There is a known conflict
with jtag, but the workaround in drivers/soc/rockchip/grf.c does not
work. Adding the broken-cd attribute to the DTS fixes the issue.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
OF graph describes USB data lanes between USB-PHY and respective MUIC.
Since graph is present and DWC driver can use it to get extcon, obsolete
extcon property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a thermal-zone node and fill in all the sensors available in a
cp110 (only one in the thermal IP).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Because the label is different between CPs, the full path of a node is
unique. However, when referring to the end of the path only (the node
name), this name is not unique anymore.
The *thermal_zone_of_sensor_register() functions of the thermal core
present this limitation and prevent having a thermal-zone per CP.
Add a macro to make the distinction between node names to solve this
situation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add a thermal-zone node and fill in all the sensors available in an
ap806 (one in the IC plus one per CPU).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
New bindings impose to declare the thermal IP from within a new syscon.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
PCIe features like AER, Hotplug, PME, DPC depend on PCIEPORTBUS,
so enable PCIEPORTBUS as default.
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Support for VGA_CONSOLE is not allowable due to commit ee23794b86
("video: vgacon: Don't build on arm64"), thus remove the associated
unused code.
Whilst PCI on arm64 would support VGA a valid screen_info structure
is missing.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
include/linux/mmzone.h describes ARCH_HAS_HOLES_MEMORYMODEL as
relevant when parts the memmap have been free()d. This would
happen on systems where memory is smaller than a sparsemem-section,
and the extra struct pages are expensive. pfn_valid() on these
systems returns true for the whole sparsemem-section, so an extra
memmap_valid_within() check is needed.
On arm64 we have nomap memory, so always provide pfn_valid() to test
for nomap pages. This means ARCH_HAS_HOLES_MEMORYMODEL's extra checks
are already rolled up into pfn_valid().
Remove it.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Armv8.4-A extension enables MRS instruction encodings inside ESR_ELx.ISS
during exception class ESR_ELx_EC_SYS64 (0x18). This encoding can be used
to emulate MRS instructions which can avoid fetch/decode from user space
thus improving performance. This adds a new sys64_hook structure element
with applicable ESR mask/value pair for MRS instructions on various system
registers but constrained by sysreg encodings which is currently allowed
to be emulated.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
MRS emulation gets triggered with exception class (0x00 or 0x18) eventually
calling the function emulate_mrs() which fetches the user space instruction
and analyses it's encodings (OP0, OP1, OP2, CRN, CRM, RT). The kernel tries
to emulate the given instruction looking into the encoding details. Going
forward these encodings can also be parsed from ESR_ELx.ISS fields without
requiring to fetch/decode faulting userspace instruction which can improve
performance. This factorizes emulate_mrs() function in a way that it can be
called directly with MRS encodings (OP0, OP1, OP2, CRN, CRM) for any given
target register which can then be used directly from 0x18 exception class.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Extracting target register from ESR.ISS encoding has already been required
at multiple instances. Just make it a macro definition and replace all the
existing use cases.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Enable CAAM (Cryptographic Accelerator and Assurance Module) driver
for QorIQ Data Path Acceleration Architecture (DPAA) v2.
It handles DPSECI (Data Path SEC Interface) DPAA2 objects that sit
on the Management Complex (MC) fsl-mc bus.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Crypto Extension instantiation of the aes-modes.S collection of
skciphers uses only 15 NEON registers for the round key array, whereas
the pure NEON flavor uses 16 NEON registers for the AES S-box.
This means we have a spare register available that we can use to hold
the XTS mask vector, removing the need to reload it at every iteration
of the inner loop.
Since the pure NEON version does not permit this optimization, tweak
the macros so we can factor out this functionality. Also, replace the
literal load with a short sequence to compose the mask vector.
On Cortex-A53, this results in a ~4% speedup.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, we rely on the generic CTS chaining mode wrapper to
instantiate the cts(cbc(aes)) skcipher. Due to the high performance
of the ARMv8 Crypto Extensions AES instructions (~1 cycles per byte),
any overhead in the chaining mode layers is amplified, and so it pays
off considerably to fold the CTS handling into the SIMD routines.
On Cortex-A53, this results in a ~50% speedup for smaller input sizes.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The reasoning of commit f10dc56c64 ("crypto: arm64 - revert NEON yield
for fast AEAD implementations") applies equally to skciphers: the walk
API already guarantees that the input size of each call into the NEON
code is bounded to the size of a page, and so there is no need for an
additional TIF_NEED_RESCHED flag check inside the inner loop. So revert
the skcipher changes to aes-modes.S (but retain the mac ones)
This partially reverts commit 0c8f838a52.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For some reason, the asmlinkage prototypes of the NEON routines take
u8[] arguments for the round key arrays, while the actual round keys
are arrays of u32, and so passing them into those routines requires
u8* casts at each occurrence. Fix that.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There's no need to treat mismatched cache-line sizes reported by CTR_EL0
differently to any other mismatched fields that we treat as "STRICT" in
the cpufeature code. In both cases we need to trap and emulate EL0
accesses to the register, so drop ARM64_MISMATCHED_CACHE_LINE_SIZE and
rely on ARM64_MISMATCHED_CACHE_TYPE instead.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: move ARM64_HAS_CNP in the empty cpucaps.h slot]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add devicetree support for HiKey970 development board which
based on Hi3670 SoC and is also one of the 96Boards Consumer
Edition and AI platform.
Only UART6 is enabled which is the default console required
by the 96Boards Consumer Edition Specification.
This patch has been tested on HiKey970 Board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add initial devicetree support for Hisilicon Hi3670 SoC which
is similar to Hi3660 SoC with NPU support.
This SoC has Octal core BigLittle CPUs in two clusters(4 * A53 & 4 * A73).
Only UART6 has been added for console support which is
pre configured by the bootloader. A fixed clock is sourcing
the UART6 which will get replaced by the clock driver when available.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The clocks property should either be present for all the CPUs of a
cluster or none. If these are present only for a subset of CPUs of a
cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add missing clocks property.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Describe CMTs in the R8A779{7|8}0 device trees.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC and EEPROM can operate at 400kHz, so use this speed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car V3H hook up SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS1 to match
information in the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car E3 hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car H3.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add TISCI compatible System controller for AM6 SoCs.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add secure proxy instance for Main domain
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add uart nodes for AM654 device tree components.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM65 has two PCIe controllers and each PCIe controller has '2' address
spaces one within the 4GB address space of the SoC and the other above
the 4GB address space of the SoC (cbass_main) in addition to the
register space. The size of the address space above the 4GB SoC address
space is 4GB. These address ranges will be used by CPU/DMA to access
the PCIe address space. In order to represent the address space above
the 4GB SoC address space and to represent the size of this address
space as 4GB, change address-cells and size-cells of interconnect to 2.
Since OSPI has similar need in MCU Domain Memory Map, change
address-cells and size-cells of cbass_mcu interconnect also to 2.
Fixes: ea47eed33a ("arm64: dts: ti: Add Support for AM654 SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We rely on cpufeature framework to detect and enable CNP so for KVM we
need to patch hyp to set CNP bit just before TTBR0_EL2 gets written.
For the guest we encode CNP bit while building vttbr, so we don't need
to bother with that in a world switch.
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Common Not Private (CNP) is a feature of ARMv8.2 extension which
allows translation table entries to be shared between different PEs in
the same inner shareable domain, so the hardware can use this fact to
optimise the caching of such entries in the TLB.
CNP occupies one bit in TTBRx_ELy and VTTBR_EL2, which advertises to
the hardware that the translation table entries pointed to by this
TTBR are the same as every PE in the same inner shareable domain for
which the equivalent TTBR also has CNP bit set. In case CNP bit is set
but TTBR does not point at the same translation table entries for a
given ASID and VMID, then the system is mis-configured, so the results
of translations are UNPREDICTABLE.
For kernel we postpone setting CNP till all cpus are up and rely on
cpufeature framework to 1) patch the code which is sensitive to CNP
and 2) update TTBR1_EL1 with CNP bit set. TTBR1_EL1 can be
reprogrammed as result of hibernation or cpuidle (via __enable_mmu).
For these two cases we restore CnP bit via __cpu_suspend_exit().
There are a few cases we need to care of changes in TTBR0_EL1:
- a switch to idmap
- software emulated PAN
we rule out latter via Kconfig options and for the former we make
sure that CNP is set for non-zero ASIDs only.
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
[catalin.marinas@arm.com: default y for CONFIG_ARM64_CNP]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Memory for host controller data structures is allocated local to the node
to which the controller is associated with. This has been the behaviour
since support for ACPI was added in commit 0cb0786bac ("ARM64: PCI:
Support ACPI-based PCI host controller").
Drop the node local allocation as there is no benefit from doing so - the
usage of these structures is independent from where the controller is
located.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Instructions for modifying the PSTATE fields which were not supported
in the older toolchains (e.g, PAN, UAO) are generated using macros.
We have so far used the normal sys_reg() helper for defining the PSTATE
fields. While this works fine, it is really difficult to correlate the
code with the Arm ARM definition.
As per Arm ARM, the PSTATE fields are defined only using Op1, Op2 fields,
with fixed values for Op0, CRn. Also the CRm field has been reserved
for the Immediate value for the instruction. So using the sys_reg()
looks quite confusing.
This patch cleans up the instruction helpers by bringing them
in line with the Arm ARM definitions to make it easier to correlate
code with the document. No functional changes.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dtb: Warning (i2c_bus_reg): /i2c@ff3d0000/codec@0a: I2C bus unit address format error, expected "a"
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the Renesas RZ/G2E (R8A774C0) SoC in the ARM64 defconfig.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.
Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked to
the SoC CSI-2 receiver port.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
dtc has new checks for SPI buses. The meson dts files have a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dtb: Warning (spi_bus_bridge): /soc/periphs@c8834000/pinctrl@4b0/spi: incorrect #address-cells for SPI bus
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The bad_mode() handler is called if we encounter an uunknown exception,
with the expectation that the subsequent call to panic() will halt the
system. Unfortunately, if the exception calling bad_mode() is taken from
EL0, then the call to die() can end up killing the current user task and
calling schedule() instead of falling through to panic().
Remove the die() call altogether, since we really want to bring down the
machine in this "impossible" case.
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
force_signal_inject() is designed to send a fatal signal to userspace,
so WARN if the current pt_regs indicates a kernel context. This can
currently happen for the undefined instruction trap, so patch that up so
we always BUG() if we didn't have a handler.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The cpu errata and feature enable callbacks are only called via their
respective arm64_cpu_capabilities structure and therefore shouldn't
exist in the global namespace.
Move the PAN, RAS and cache maintenance emulation enable callbacks into
the same files as their corresponding arm64_cpu_capabilities structures,
making them static in the process.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When running without VHE, it is necessary to set SCTLR_EL2.DSSBS if SSBD
has been forcefully disabled on the kernel command-line.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On CPUs with support for PSTATE.SSBS, the kernel can toggle the SSBD
state without needing to call into firmware.
This patch hooks into the existing SSBD infrastructure so that SSBS is
used on CPUs that support it, but it's all made horribly complicated by
the very real possibility of big/little systems that don't uniformly
provide the new capability.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Rather than panic() when taking an undefined instruction exception from
EL1, allow a hook to be registered in case we want to emulate the
instruction, like we will for the SSBS PSTATE manipulation instructions.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we're all merged nicely into mainline, there's no need to check
to see if PR_SPEC_STORE_BYPASS is defined.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Armv8.5 introduces a new PSTATE bit known as Speculative Store Bypass
Safe (SSBS) which can be used as a mitigation against Spectre variant 4.
Additionally, a CPU may provide instructions to manipulate PSTATE.SSBS
directly, so that userspace can toggle the SSBS control without trapping
to the kernel.
This patch probes for the existence of SSBS and advertise the new instructions
to userspace if they exist.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
I was passing through and figuered I'd fix this up:
featuer -> feature
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The thermal device is supposed to be always enabled. As the default
value of the status property is "okay", there is no need to make this
explicit in SoC-specific .dtsi files where no override is involved.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dtb: Warning (i2c_bus_reg): /hsls/i2c@e0000/pcf8574@20: I2C bus unit address format error, expected "27"
arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dtb: Warning (i2c_bus_reg): /hsls/i2c@e0000/pcf8574@20: I2C bus unit address format error, expected "27"
arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dtb: Warning (spi_bus_bridge): /hsls/ssp@180000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dtb: Warning (spi_bus_bridge): /hsls/ssp@190000: node name for SPI buses should be 'spi'
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The smd and smp2p drivers now support accessing the APCS GLOBAL IPC
register through the mailbox framework, so migrate the msm8996 dts to
use this and remove the syscon based APCS node.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The QRTR packet family is used for a wide range of communication between
services in Qualcomm platforms. Examples of services using this
transport for communication are remoteproc management, modem control,
positioning, power management and WiFi.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The thermal zone uses spmi-temp-alarm as sensor, the trip points
correspond to the PMIC thermal stages 1 and 2. The critical trip
point at 125°C disables the partial PMIC shutdown at stage 2.
Without an IIO input the sensor only reports a limited number of
temperatures:
- 37°C for temperatures below 105°C
- 107°C for temperatures >= 105°C and < 125°C
- 127°C for temperatures >= 125°C
(the numbers correspond to a stage 1 threshold of 105°C)
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the spmi-temp-alarm node to pm8998 based on the examples in the
bindings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the display clock controller node to sdm845 based on the
examples in the bindings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the SMP2P nodes for the remoteproc states for adsp, cdsp and slpi.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Set the various nodes to "okay" and hook up the regulators.
NOTE: For now the main USB port (the one that goes out the Type C
connector) is forced to host. Eventually someone will need to get the
Type C detection hooked up and get this all integrated with the
PMI8998 PMIC. The reason for forcing to "host" in the meantime is
that this will leave us with one "host" and one "peripheral" port.
In order for host mode this to work, we assume that the bootloader
left things configured enough for us. Apparently the magic for that
is is to do these writes on pmi8998:
- pm_comm_write_byte(2, 0x1153, 0x2C, 0);
- pm_comm_write_byte(2, 0x1152, 0x07, 0);
- pm_comm_write_byte(2, 0x1140, 0x00, 0);
- pm_comm_write_byte(2, 0x1140, 0x01, 0);
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add regulator devices for PMIC regulators managed via VRM and XOB
RPMh accelerators.
A few notes here:
- Regulators are added directly to the board file. While it's true
that this will mean a bunch of copy/pasting for other boards that
are very similar, this is probably the right call since boards
could make changes to the way these regulators are hooked up and
trying to find a way to avoid duplication will result in some
confusing node overrides.
- Regulators that are hooked up to supply pins on the SoC are given
an alias matching the name of that pin (pin name comes from the
Qualcomm SoC "device specification" doc).
- Other regulator labels are based on the schematic. If there is
more than one logical name on the schematic for the same rail the
secondary names are also listed and should be referred to as
appropriate.
- Regulators all default to HPM mode w/ no ability to switch modes.
Future patches can switch things to LPM and possibly add
dynamic load switching if we have determined there's a benefit.
This should only be done for rails where we'll actually be able
to take advantage of the lower power modes so we don't need to
churn with lots of patches adding regulator_set_load() calls
to drivers.
NOTE: This patch is loosely based on one originally shared to me by
David Collins.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds nodes for USB and related PHYs.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[dianders: reworked quite a bit]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the node to support AOSS reset driver on
SDM845
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: Updated addresses to match the binding that was merged]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
DTS board files should always specify model and compatible.
All DTS board files that includes msm8996.dtsi
already specifies model and compatible, and will thus
override the model and compatible in msm8996.dtsi.
Drop model from msm8916.dtsi, since it is only a source of confusion.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
DTS board files should always specify model and compatible.
All DTS board files that includes msm8916.dtsi
already specifies model and compatible, and will thus
override the model and compatible in msm8916.dtsi.
Drop model and compatible from msm8916.dtsi,
since they are only a source of confusion.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add qcom,apq8096 to compatible string.
This compatible is defined in Documentation/devicetree/bindings/arm/qcom.txt
and is needed for e.g. drivers/cpufreq/qcom-cpufreq-kryo.c to be probed
correctly (and for drivers/cpufreq/cpufreq-dt-platdev.c to work properly).
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add pon, coincell and rtc to the first pm8998 sid.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the adsp, modem and slpi smp2p nodes to msm8998.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the firmware and scm nodes for msm8998
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add new dtsi file for the PMI8998, with its gpios and include all three
PMICs in the MSM8998 MTP dts.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the two tsens instances and the thermal zones for CPUs, GPUs,
battery and skin sensors.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add nodes for RPM communication for MSM8998 and the regulator nodes for
the MTP.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial device tree support for the Qualcomm MSM8998 SoC and
MTP8998 evaluation board.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Imran Khan <kimran@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Restructured, removed its node and moved to SPDX headers]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the adc node to pm8998 based on the examples in the
bindings. It also fixes the order of the included headers.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Resin is board specific, so add the resin node in apq8096-db820c dtsi
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Resin is board specific so add the resin node in apq8016-sbc dtsi
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add PON and pwrkey as child nodes for PON device. Also
add additional properties for pwrkey i.e., linux,code
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The order between "syscon" and "simple-mfd" is important because in these
particular cases, the node needs to be first a "simple-mfd" to expose
it's sub-nodes, and later on a "syscon" to permit other nodes to access
this register space through the "syscon" mechanism.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The r8a77965 has a single FDP1 instance.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Device nodes with unit addresses are sorted by unit address,
- Device nodes without unit addresses and references are sorted
alphabetically.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Successfully tested on H3 ES1.0 and ES2.0, M3-W ES1.0, and M3-N ES1.0.
Even previously stubborn cards work fine. Transfer rates were >60MB/s.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers, incl. clocks, power
domains, and resets properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK, and describe the clock
inputs for the Baud Rate Generator for External Clock (BRG) for SCIF2,
which can increase serial clock accuracy.
The presence of the SCIF_CLK crystal and its clock frequency depend on
the actual board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Enhance patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the SoC-specific CPG/MSSR include file to allow future use of
R8A77990_CLK_* symbols.
Replace the hardcoded power domain indices by R8A77990_PD_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The comments describing the non-default switch settings to use SATA are
confusing: 'Off' refers to the switch position, not to the MD12 logic
value, while the parentheses suggest otherwise. Rephrase to fix this.
Fixes: bec000784d5bb571 ("arm64: dts: renesas: salvator-xs: enable SATA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: updated for a few new cases]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is based on the existing KF device tree sources:
$ ls -1 arch/arm64/boot/dts/renesas/*-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dts
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable PCIe PHY and PCIEC and specify the PCIe bus clock for the Condor
board.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the PCIe PHY, PCIEC, and PCIe bus clock in the R8A77980 device
tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb3.0 phy, host and function device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb dmac and hsusb device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add FCPF and FCPV instances to the r8a774a1 dtsi, similarly
to what was done for the r8a7796 with commit 41dbbf0c5b
("arm64: dts: r8a7796: Add FCPF and FCPV instances"),
commit 69490bc966 ("arm64: dts: renesas: r8a7796: Point
FDP1 via FCPF to IPMMU-VI0"), and commit cef942d0bd ("arm64:
dts: renesas: r8a7796: Point VSPI via FCPVI to IPMMU-VC0").
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add sound support for the RZ/G2M SoC (a.k.a. R8A774A1).
This work is based on similar work done on the R8A7796 SoC
by Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PWM[0123456] device nodes to the RZ/G2M (a.k.a R8A774A1)
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds definitions for L2 cache for the Cortex-A53 CPU
cores (512 KiB in size, organized as 32 KiB x 16 ways), adds
Cortex-A53 CPU cores (setting a total of 6 cores, 2 x Cortex-A57
+ 4 x Cortex-A53), and finally enables the performance monitor
unit for the Cortex-A53 cores on the R8A774A1 SoC.
Based on work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers on RZ/G2M SoC.
Based on several similar patches of the R8A7796 device tree
by Geert Uytterhoeven <geert+renesas@glider.be>
and Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add thermal support for R8A774A1 (RZ/G2M) SoC.
Based on the work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-6] and IIC Bus Interface for DVFS (IIC for DVFS)
devices nodes to the r8a774a1 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add GPIO device nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the SoC specific part of the Ethernet AVB
device tree node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the Interrupt Controller for External Devices
(INTC-EX) on RZ/G2M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all RZ/G2M SCIF and HSCIF serial ports,
incl. clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor/V3HSK board dependent parts of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the eMMC chip support for the V3M Started Kit board.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the MMC0 (SDHI2) device node.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds OPPs table for CA57{0,1} cpu devices
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
[simon: do not give nodes unit names as they have no bus addresses]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow the bare M3-N-based ULCB board to boot.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 HW manual rev1.00, R-Car M3-N has two CAN
interfaces, similar to H3, M3-W and other SoCs from the same family.
Add CAN placeholder nodes to avoid below DTC errors:
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:19.1-6 Label or path can0 not found
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:25.1-6 Label or path can1 not found
These errors occur *after* the addition of r8a77965-m3nulcb-kf.dts.
Fix them beforehand.
CAN support is inspired from below commits:
- v4.7 commit 308b7e4ba6 ("arm64: dts: r8a7795: Add CAN support")
- v4.11 commit 909c162524 ("arm64: dts: r8a7796: Add CAN support")
- v4.12 commit bec0948e81 ("arm64: dts: r8a7796: Add reset control properties")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[simon: make placeholder minimal by only including reg property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car M3-N hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car M3-W.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ensure that the ADV748x device addresses do not conflict, and group them
together (visually in i2cdetect)
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the CSI2 and VIN (and their interconnections) in the R8A77980
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the nodes to enable SATA. Note that MD12 (SW12-7) must be switched
off for that to work.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds SATA controller node for the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add missing chosen and memory nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Use the correct compatible for the AXG ethernet mac node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the PDM input device on the S400 and it to the sound card
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are 7 digital mics on the MIC daughter board attached
to the s400 board, so add the digital microphone codec to
its DTS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
DMC is a small memory region with various registers,
including the ones needed for the canvas module.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There is actually several different libretech board with the CC suffix
so the model name is not appropriate here. Update to something more
specific
Reported-by: Da Xue <da@lessconfused.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Devices using the new V4L2 mem2mem vdec require a larger CMA pool. As
nearly all GX* devices are video/media focused and will use it, set a
larger (256MB) default value.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Sort DT nodes by address when possible, by node node name otherwise.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
As we have already binding for the H6 system controller, add its node
to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[fixed compatible string]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Peter Z asked me to justify the barrier usage in asm/tlbflush.h, but
actually that whole block comment needs to be rewritten.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
By selecting HAVE_RCU_TABLE_INVALIDATE, we can rely on tlb_flush() being
called if we fail to batch table pages for freeing. This in turn allows
us to postpone walk-cache invalidation until tlb_finish_mmu(), which
avoids lots of unnecessary DSBs and means we can shoot down the ASID if
the range is large enough.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that the core mmu_gather code keeps track of both the levels of page
table cleared and also whether or not these entries correspond to
intermediate entries, we can use this in our tlb_flush() callback to
reduce the number of invalidations we issue as well as their scope.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If there's one thing the RCU-based table freeing doesn't need, it's more
ifdeffery.
Remove the redundant !CONFIG_HAVE_RCU_TABLE_FREE code, since this option
is unconditionally selected in our Kconfig.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When we are unmapping intermediate page-table entries or huge pages, we
don't need to issue a TLBI instruction for every PAGE_SIZE chunk in the
VA range being unmapped.
Allow the invalidation stride to be passed to __flush_tlb_range(), and
adjust our "just nuke the ASID" heuristic to take this into account.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a comment to explain why we can't get away with last-level
invalidation in flush_tlb_range()
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that our walk-cache invalidation routines imply a DSB before the
invalidation, we no longer need one when we are clearing an entry during
unmap.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__flush_tlb_[kernel_]pgtable() rely on set_pXd() having a DSB after
writing the new table entry and therefore avoid the barrier prior to the
TLBI instruction.
In preparation for delaying our walk-cache invalidation on the unmap()
path, move the DSB into the TLB invalidation routines.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
flush_tlb_kernel_range() is only ever used to invalidate last-level
entries, so we can restrict the scope of the TLB invalidation
instruction.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The CAN clock node should precede the "cpus" node in the R8A779{7|8}0
device trees, according to the alphanumeric node sorting rule...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IPMMU nodes should follow the GEther node, not the CAN-FD node,
according to the <unit-address> part of the startng IPMMU-DS1 node.
While moving the nodes, also do sort them by label alphanumerically...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PWM device nodes and enables PWM3 and PWM5 for
R-Car E3 Ebisu board. These devices are used for backlight control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the performance monitor unit (PMU) for the Cortex-A53 cores in
the R8A77980 SoC's device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add configuration option for the RZ/G2M (R8A774A1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We do not enable scatter-gather mode in the TMC-ETR by default
to prevent malfunctioning of systems where the ETR may not be
properly connected to the memory subsystem to allow for simultaneous
READ/WRITE transactions when used in SG mode. Instead we whitelist
the platforms where we know that it is safe to use the mode.
All revisions of Juno have a proper ETR connection and hence
white list them.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pierlisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since commit 23c85094fe ("proc/kcore: add vmcoreinfo note to /proc/kcore")
the kernel has exported the vmcoreinfo PT_NOTE on /proc/kcore as well
as /proc/vmcore.
arm64 only exposes it's additional arch information via
arch_crash_save_vmcoreinfo() if built with CONFIG_KEXEC, as kdump was
previously the only user of vmcoreinfo.
Move this weak function to a separate file that is built at the same
time as its caller in kernel/crash_core.c. This ensures values like
'kimage_voffset' are always present in the vmcoreinfo PT_NOTE.
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
All other uses of "asm goto" go through asm_volatile_goto, which avoids
a miscompile when using GCC < 4.8.2. Replace our open-coded "asm goto"
statements with the asm_volatile_goto macro to avoid issues with older
toolchains.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add the gpio-controlled regulator and add the supply to the otg-port of phy0.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current implementation of get/put_user_unsafe default to get/put_user
which toggle PAN before each access, despite having been told by the caller
that multiple accesses to user memory were about to happen.
Provide implementations for user_access_begin/end to turn PAN off/on and
implement unsafe accessors that assume PAN was already turned off.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Being consistent in our capitalisation for page-table dumps helps when
grepping for things like "end".
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Unlike crc32c(), which is wired up to the crypto API internally so the
optimal driver is selected based on the platform's capabilities,
crc32_le() is implemented as a library function using a slice-by-8 table
based C implementation. Even though few of the call sites may be
bottlenecks, calling a time variant implementation with a non-negligible
D-cache footprint is a bit of a waste, given that ARMv8.1 and up mandates
support for the CRC32 instructions that were optional in ARMv8.0, but are
already widely available, even on the Cortex-A53 based Raspberry Pi.
So implement routines that use these instructions if available, and fall
back to the existing generic routines otherwise. The selection is based
on alternatives patching.
Note that this unconditionally selects CONFIG_CRC32 as a builtin. Since
CRC32 is relied upon by core functionality such as CONFIG_OF_FLATTREE,
this just codifies the status quo.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a CRC32 feature bit and wire it up to the CPU id register so we
will be able to use alternatives patching for CRC32 operations.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch fixes pin assign of vcc_host1_5v. This regulator is
controlled by USB20_HOST_DRV signal.
ROCK64 schematic says that GPIO0_A2 pin is used as USB20_HOST_DRV.
GPIO0_D3 pin is for SPDIF_TX_M0.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit adds WiFi module support for the Firefly-RK3399.
Signed-off-by: Shohei Maruyama <cheat.sc.linux@outlook.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On the board DVS2 is disabled and not connected, see schematic, page 16.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pin is GPIO4-D1 not GPIO1-D1, see schematic, page 15 for reference.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Asymmetric CPU capacity can not necessarily be determined accurately at
the time the initial sched_domain hierarchy is built during boot. It is
therefore necessary to be able to force a full rebuild of the hierarchy
later triggered by the arch_topology driver. A full rebuild requires the
arch-code to implement arch_update_cpu_topology() which isn't yet
implemented for arm64. This patch points the arm64 implementation to
arch_topology driver to ensure that full hierarchy rebuild happens when
needed.
Signed-off-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: dietmar.eggemann@arm.com
Cc: valentin.schneider@arm.com
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/1532093554-30504-4-git-send-email-morten.rasmussen@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ARM:
- Fix a VFP corruption in 32-bit guest
- Add missing cache invalidation for CoW pages
- Two small cleanups
s390:
- Fallout from the hugetlbfs support: pfmf interpretion and locking
- VSIE: fix keywrapping for nested guests
PPC:
- Fix a bug where pages might not get marked dirty, causing
guest memory corruption on migration,
- Fix a bug causing reads from guest memory to use the wrong guest
real address for very large HPT guests (>256G of memory), leading to
failures in instruction emulation.
x86:
- Fix out of bound access from malicious pv ipi hypercalls (introduced
in rc1)
- Fix delivery of pending interrupts when entering a nested guest,
preventing arbitrarily late injection
- Sanitize kvm_stat output after destroying a guest
- Fix infinite loop when emulating a nested guest page fault
and improve the surrounding emulation code
- Two minor cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJbk5gAAAoJEED/6hsPKofoS0UH/1clCzg/8x3jhpDcKKp6tDm7
9XHOOQ6XmydT0HXYJNqZepGNqU99ip+2u4x8E9LCT5MTvTMZ1BcNM6PmenjJVULY
GMJtwZhjqoklrOcNkXGqIye4Ec+I0pBuMmt0AN0N85CcHO8VUBpMzsdxgJLuxcRm
UT6OZnCLyJsock6BqkZmqVsJj/gemFnI9MpudnrU8cCFk60roXmQWJ66fMIFfKjt
q0R61t8nmbapQKE8pjqBNgbCsuotVOtU1zgMkeM5LkaYEfc65ZPdgt3sdpyG8Guq
WA7Vt6HEvmNrcQxHFX5P0GxTVM9lOVCUx1bKXE4+57CMZOYl/8hDaTudlcacutg=
=FyuN
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix a VFP corruption in 32-bit guest
- Add missing cache invalidation for CoW pages
- Two small cleanups
s390:
- Fallout from the hugetlbfs support: pfmf interpretion and locking
- VSIE: fix keywrapping for nested guests
PPC:
- Fix a bug where pages might not get marked dirty, causing guest
memory corruption on migration
- Fix a bug causing reads from guest memory to use the wrong guest
real address for very large HPT guests (>256G of memory), leading
to failures in instruction emulation.
x86:
- Fix out of bound access from malicious pv ipi hypercalls
(introduced in rc1)
- Fix delivery of pending interrupts when entering a nested guest,
preventing arbitrarily late injection
- Sanitize kvm_stat output after destroying a guest
- Fix infinite loop when emulating a nested guest page fault and
improve the surrounding emulation code
- Two minor cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
KVM: LAPIC: Fix pv ipis out-of-bounds access
KVM: nVMX: Fix loss of pending IRQ/NMI before entering L2
arm64: KVM: Remove pgd_lock
KVM: Remove obsolete kvm_unmap_hva notifier backend
arm64: KVM: Only force FPEXC32_EL2.EN if trapping FPSIMD
KVM: arm/arm64: Clean dcache to PoC when changing PTE due to CoW
KVM: s390: Properly lock mm context allow_gmap_hpage_1m setting
KVM: s390: vsie: copy wrapping keys to right place
KVM: s390: Fix pfmf and conditional skey emulation
tools/kvm_stat: re-animate display of dead guests
tools/kvm_stat: indicate dead guests as such
tools/kvm_stat: handle guest removals more gracefully
tools/kvm_stat: don't reset stats when setting PID filter for debugfs
tools/kvm_stat: fix updates for dead guests
tools/kvm_stat: fix handling of invalid paths in debugfs provider
tools/kvm_stat: fix python3 issues
KVM: x86: Unexport x86_emulate_instruction()
KVM: x86: Rename emulate_instruction() to kvm_emulate_instruction()
KVM: x86: Do not re-{try,execute} after failed emulation in L2
KVM: x86: Default to not allowing emulation retry in kvm_mmu_page_fault
...
A few more fixes who have trickled in:
- MMC bus width fixup for some Allwinner platforms
- Fix for NULL deref in ti-aemif when no platform data is passed in
- Fix div by 0 in SCMI code
- Add a missing module alias in a new RPi driver
-----BEGIN PGP SIGNATURE-----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=oZbn
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes who have trickled in:
- MMC bus width fixup for some Allwinner platforms
- Fix for NULL deref in ti-aemif when no platform data is passed in
- Fix div by 0 in SCMI code
- Add a missing module alias in a new RPi driver"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
memory: ti-aemif: fix a potential NULL-pointer dereference
firmware: arm_scmi: fix divide by zero when sustained_perf_level is zero
hwmon: rpi: add module alias to raspberrypi-hwmon
arm64: allwinner: dts: h6: fix Pine H64 MMC bus width
Just one fix for H6 mmc on the Pine H64: the mmc bus width was missing
from the device tree. This was added in 4.19-rc1.
-----BEGIN PGP SIGNATURE-----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=WbHO
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.19
Just one fix for H6 mmc on the Pine H64: the mmc bus width was missing
from the device tree. This was added in 4.19-rc1.
* tag 'sunxi-fixes-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: dts: h6: fix Pine H64 MMC bus width
Signed-off-by: Olof Johansson <olof@lixom.net>
There is no reason to leave the per-device dma_ops around when
deconfiguring a device, so move this code from arm64 into the
common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
- Fix a VFP corruption in 32-bit guest
- Add missing cache invalidation for CoW pages
- Two small cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbkngmAAoJEEtpOizt6ddyeaoH/15bbGHlwWf23tGjSoDzhyD4
zAXfy+SJdm4cR8K7jEkVrNffkEMAby7Zl28hTHKB9jsY1K8DD+EuCE3Nd4kkVAsc
iHJwV4aiHil/zC5SyE0MqMzELeS8UhsxESYebG6yNF0ElQDQ0SG+QAFr47/OBN9S
u4I7x0rhyJP6Kg8z9U4KtEX0hM6C7VVunGWu44/xZSAecTaMuJnItCIM4UMdEkSs
xpAoI59lwM6BWrXLvEunekAkxEXoR7AVpQER2PDINoLK2I0i0oavhPim9Xdt2ZXs
rqQqfmwmPOVvYbexDp97JtfWo3/psGLqvgoK1tq9bzF3u6Y3ylnUK5IspyVYwuQ=
=TK8A
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-fixes-for-v4.19-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
Fixes for KVM/ARM for Linux v4.19 v2:
- Fix a VFP corruption in 32-bit guest
- Add missing cache invalidation for CoW pages
- Two small cleanups
The lock has never been used and the page tables are protected by
mmu_lock in struct kvm.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
kvm_unmap_hva is long gone, and we only have kvm_unmap_hva_range to
deal with. Drop the now obsolete code.
Fixes: fb1522e099 ("KVM: update to new mmu_notifier semantic v2")
Cc: James Hogan <jhogan@kernel.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
If trapping FPSIMD in the context of an AArch32 guest, it is critical
to set FPEXC32_EL2.EN to 1 so that the trapping is taken to EL2 and
not EL1.
Conversely, it is just as critical *not* to set FPEXC32_EL2.EN to 1
if we're not going to trap FPSIMD, as we then corrupt the existing
VFP state.
Moving the call to __activate_traps_fpsimd32 to the point where we
know for sure that we are going to trap ensures that we don't set that
bit spuriously.
Fixes: e6b673b741 ("KVM: arm64: Optimise FPSIMD handling to reduce guest/host thrashing")
Cc: stable@vger.kernel.org # v4.18
Cc: Dave Martin <dave.martin@arm.com>
Reported-by: Alexander Graf <agraf@suse.de>
Tested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
In pmd_free_pte_page() and pud_free_pmd_page() we try to warn if they
hit a present non-table entry. In both cases we'll warn for non-present
entries, as the VM_WARN_ON() only checks the entry is not a table entry.
This has been observed to result in warnings when booting a v4.19-rc2
kernel under qemu.
Fix this by bailing out earlier for non-present entries.
Fixes: ec28bb9c9b ("arm64: Implement page table free interfaces")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Renesas R-Car gen3 SoCs have both CMT and TMU timers, so we have to enable
building them in Kconfig.platforms (as they don't normally have the prompts
in Kconfig).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable DRM Support for Allwinner Display Engine, built as a module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Drop stackleak_check_alloca() for arm64 since the STACKLEAK gcc plugin now
doesn't track stack depth overflow caused by alloca().
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The arm64 implementation of the CRC-T10DIF algorithm uses the 64x64 bit
polynomial multiplication instructions, which are optional in the
architecture, and if these instructions are not available, we fall back
to the C routine which is slow and inefficient.
So let's reuse the 64x64 bit PMULL alternative from the GHASH driver that
uses a sequence of ~40 instructions involving 8x8 bit PMULL and some
shifting and masking. This is a lot slower than the original, but it is
still twice as fast as the current [unoptimized] C code on Cortex-A53,
and it is time invariant and much easier on the D-cache.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reorganize the CRC-T10DIF asm routine so we can easily instantiate an
alternative version based on 8x8 polynomial multiplication in a
subsequent patch.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that the scalar fallbacks have been moved out of this driver into
the core crc32()/crc32c() routines, we are left with a CRC32 crypto API
driver for arm64 that is based only on 64x64 polynomial multiplication,
which is an optional instruction in the ARMv8 architecture, and is less
and less likely to be available on cores that do not also implement the
CRC32 instructions, given that those are mandatory in the architecture
as of ARMv8.1.
Since the scalar instructions do not require the special handling that
SIMD instructions do, and since they turn out to be considerably faster
on some cores (Cortex-A53) as well, there is really no point in keeping
this code around so let's just remove it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace the literal load of the addend vector with a sequence that
performs each add individually. This sequence is only 2 instructions
longer than the original, and 2% faster on Cortex-A53.
This is an improvement by itself, but also works around a Clang issue,
whose integrated assembler does not implement the GNU ARM asm syntax
completely, and does not support the =literal notation for FP registers
(more info at https://bugs.llvm.org/show_bug.cgi?id=38642)
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These are unused, undesired, and have never actually been used by
anybody. The original authors of this code have changed their mind about
its inclusion. While originally proposed for disk encryption on low-end
devices, the idea was discarded [1] in favor of something else before
that could really get going. Therefore, this patch removes Speck.
[1] https://marc.info/?l=linux-crypto-vger&m=153359499015659
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The NXP LS208xA SoCs have two dual uarts. Thus, add the second one.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per IFC binding, Absence of "little-endian" field causes registers
access in big-endian mode.
So no need to set explicit big-endian field IFC node for LS1043A and
LS1046A.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
NOR and IFC controller connectivity is big-endian.
So add big-endian field in nor device tree node allowing
IFC controller to read/write data from/to the flash correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "r_i2c_pins_a" label is renamed to "r_i2c_pl89_pins" to fit our
current style. The node name "i2c" is also changed to "r-i2c-pl89-pins"
to match. The reason for the peculiar name is that the other option for
muxing R_I2C is on the PL0/PL1 pins, so the name has to mention the pin
numbers in addition to the pingroup.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "uart0_pins_a" label is renamed to "uart0_pb_pins" to fit our
current style. The node name "uart0" is also changed to "uart0-pb-pins"
to match.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The eMMC 5.0 standard introduced the data strobe (DS) pin. This pin is
not used for pre-5.0 data modes, nor is it found on pre-5.0 eMMC chips.
On the A64, this pin is muxed with spi0's MISO pin. If the DS pin is
included in the mmc2 pinmux by default, this wil prevent the usage
of both mmc2 and spi0 together.
Instead, split out the DS pin to a separate pinmux that only gets used
by boards that actually have it wired up. Currently supported ones
include the Bananapi M64 and Pine64 Pinebook. These are fixed up.
Fixes: a3e8f49262 ("arm64: allwinner: a64: Add MMC pinctrl nodes")
Fixes: b8bcf0e1b2 ("arm64: allwinner: add BananaPi-M64 support")
Fixes: df35fbcfa3 ("arm64: dts: allwinner: add support for Pinebook")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
First batch of fixes post-merge window:
- A handful of devicetree changes for i.MX2{3,8} to change over to new
panel bindings. The platforms were moved from legacy framebuffers
to DRM and some development board panels hadn't yet been converted.
- OMAP fixes related to ti-sysc driver conversion fallout, fixing some
register offsets, no_console_suspend fixes, etc.
- Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.
- Fixed 0755->0644 permissions on a newly added file.
- Defconfig changes to make ARM Versatile more useful with QEMU
(helps testing).
- Enable defconfig options for new TI SoC platform that was merged this
window (AM6).
-----BEGIN PGP SIGNATURE-----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=Pdac
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"First batch of fixes post-merge window:
- A handful of devicetree changes for i.MX2{3,8} to change over to
new panel bindings. The platforms were moved from legacy
framebuffers to DRM and some development board panels hadn't yet
been converted.
- OMAP fixes related to ti-sysc driver conversion fallout, fixing
some register offsets, no_console_suspend fixes, etc.
- Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.
- Fixed 0755->0644 permissions on a newly added file.
- Defconfig changes to make ARM Versatile more useful with QEMU
(helps testing).
- Enable defconfig options for new TI SoC platform that was merged
this window (AM6)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: Enable TI's AM6 SoC platform
ARM: defconfig: Update the ARM Versatile defconfig
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: dts: imx23-evk: Convert to the new display bindings
ARM: dts: imx23-evk: Move regulators outside simple-bus
ARM: dts: imx28-evk: Convert to the new display bindings
ARM: dts: imx28-evk: Move regulators outside simple-bus
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
- Fix typos in SVE documentation
- Fix type-checking and implicit truncation for SMCCC calls
- Force CONFIG_HOLES_IN_ZONE=y so that SLAB doesn't fall over NOMAP regions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJbiSyOAAoJELescNyEwWM0Jc4IAMV6UIPNnARqKESMMGI8CPW3
+b75RKJvOz06wIsd/ko+at+4SU4om/qr5k1Yx6F2s9t1y7+1RokkP1ZXOivsOegp
KBtbDEzvwYWuePdMtZmXMMLOIOVzLC2UlqVGqdEBLNxYqfdS6H7IwgPlaXpu1GIu
n4F0d6oEKY3hTmFrmH9FN68ZrTpx8S2MZYIApokhBrNIaSyr7x8bUj8/v9OoaJsO
TwlG0y7W252alGni97WnX6gw0eM0HQ6yg8h+zNVmwksjUY+ZCS3w4ib3H8sS2FBH
vzr3XkgEPeWR1oSYO7P7Vv7erMQUCnS+q7UjQ09TVvHTcXGb3A+iqP+w3rXMbyo=
=gy5J
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A few arm64 fixes came in this week, specifically fixing some nasty
truncation of return values from firmware calls and resolving a
VM_BUG_ON due to accessing uninitialised struct pages corresponding to
NOMAP pages.
Summary:
- Fix typos in SVE documentation
- Fix type-checking and implicit truncation for SMCCC calls
- Force CONFIG_HOLES_IN_ZONE=y so that SLAB doesn't fall over NOMAP
regions"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: always enable CONFIG_HOLES_IN_ZONE
arm/arm64: smccc-1.1: Handle function result as parameters
arm/arm64: smccc-1.1: Make return values unsigned long
Documentation/arm64/sve: Couple of improvements and typos
Commit 6d526ee26c ("arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA")
only enabled HOLES_IN_ZONE for NUMA systems because the NUMA code was
choking on the missing zone for nomap pages. This problem doesn't just
apply to NUMA systems.
If the architecture doesn't set HAVE_ARCH_PFN_VALID, pfn_valid() will
return true if the pfn is part of a valid sparsemem section.
When working with multiple pages, the mm code uses pfn_valid_within()
to test each page it uses within the sparsemem section is valid. On
most systems memory comes in MAX_ORDER_NR_PAGES chunks which all
have valid/initialised struct pages. In this case pfn_valid_within()
is optimised out.
Systems where this isn't true (e.g. due to nomap) should set
HOLES_IN_ZONE and provide HAVE_ARCH_PFN_VALID so that mm tests each
page as it works with it.
Currently non-NUMA arm64 systems can't enable HOLES_IN_ZONE, leading to
a VM_BUG_ON():
| page:fffffdff802e1780 is uninitialized and poisoned
| raw: ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff
| raw: ffffffffffffffff ffffffffffffffff ffffffffffffffff ffffffffffffffff
| page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p))
| ------------[ cut here ]------------
| kernel BUG at include/linux/mm.h:978!
| Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[...]
| CPU: 1 PID: 25236 Comm: dd Not tainted 4.18.0 #7
| Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
| pstate: 40000085 (nZcv daIf -PAN -UAO)
| pc : move_freepages_block+0x144/0x248
| lr : move_freepages_block+0x144/0x248
| sp : fffffe0071177680
[...]
| Process dd (pid: 25236, stack limit = 0x0000000094cc07fb)
| Call trace:
| move_freepages_block+0x144/0x248
| steal_suitable_fallback+0x100/0x16c
| get_page_from_freelist+0x440/0xb20
| __alloc_pages_nodemask+0xe8/0x838
| new_slab+0xd4/0x418
| ___slab_alloc.constprop.27+0x380/0x4a8
| __slab_alloc.isra.21.constprop.26+0x24/0x34
| kmem_cache_alloc+0xa8/0x180
| alloc_buffer_head+0x1c/0x90
| alloc_page_buffers+0x68/0xb0
| create_empty_buffers+0x20/0x1ec
| create_page_buffers+0xb0/0xf0
| __block_write_begin_int+0xc4/0x564
| __block_write_begin+0x10/0x18
| block_write_begin+0x48/0xd0
| blkdev_write_begin+0x28/0x30
| generic_perform_write+0x98/0x16c
| __generic_file_write_iter+0x138/0x168
| blkdev_write_iter+0x80/0xf0
| __vfs_write+0xe4/0x10c
| vfs_write+0xb4/0x168
| ksys_write+0x44/0x88
| sys_write+0xc/0x14
| el0_svc_naked+0x30/0x34
| Code: aa1303e0 90001a01 91296421 94008902 (d4210000)
| ---[ end trace 1601ba47f6e883fe ]---
Remove the NUMA dependency.
Link: https://www.spinics.net/lists/arm-kernel/msg671851.html
Cc: <stable@vger.kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This adds a reference to the dts of the Compute Module IO Board V3 in arm,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
The Kconfig symbol for Renesas 64-bit ARM SoCs has always been
ARCH_RENESAS, with ARCH_SHMOBILE being selected to reuse drivers shared
with Renesas 32-bit ARM and/or Renesas SuperH SH-Mobile SoCs.
Commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
started the conversion from ARCH_SHMOBILE to ARCH_RENESAS for Renesas
32-bit SoCs. Now all drivers for Renesas ARM SoCs have gained proper
ARCH_RENESAS platform dependencies, there is no longer a need to select
ARCH_SHMOBILE.
With ARCH_SHMOBILE gone, move the ARCH_RENESAS section up, to restore
alphabetical sort order.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DesignWare I2C controller was observed running at 105.93kHz rather
than the specified 100kHz. Adjust device tree settings to bring it
within spec (a slightly conservative 98 MHz).
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Pull crypto fixes from Herbert Xu:
- Check for the right CPU feature bit in sm4-ce on arm64.
- Fix scatterwalk WARN_ON in aes-gcm-ce on arm64.
- Fix unaligned fault in aesni on x86.
- Fix potential NULL pointer dereference on exit in chtls.
- Fix DMA mapping direction for RSA in caam.
- Fix error path return value for xts setkey in caam.
- Fix address endianness when DMA unmapping in caam.
- Fix sleep-in-atomic in vmx.
- Fix command corruption when queue is full in cavium/nitrox.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: cavium/nitrox - fix for command corruption in queue full case with backlog submissions.
crypto: vmx - Fix sleep-in-atomic bugs
crypto: arm64/aes-gcm-ce - fix scatterwalk API violation
crypto: aesni - Use unaligned loads from gcm_context_data
crypto: chtls - fix null dereference chtls_free_uld()
crypto: arm64/sm4-ce - check for the right CPU feature bit
crypto: caam - fix DMA mapping direction for RSA forms 2 & 3
crypto: caam/qi - fix error path in xts setkey
crypto: caam/jr - fix descriptor DMA unmapping
Add the sound card of the s400. With it the following interface
should be working:
* Lineout
* Daugther card speaker 1 (same output as lineout)
* Linein
* SPDIF output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add TODDR and FRDDR audio fifos of the AXG SoC.
These fifos are the capture and playback memory interfaces of audio
subsystem of the AXG.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
After changing over to 64-bit time_t syscalls, many architectures will
want compat_sys_utimensat() but not respective handlers for utime(),
utimes() and futimesat(). This adds a new __ARCH_WANT_SYS_UTIME32 to
complement __ARCH_WANT_SYS_UTIME. For now, all 64-bit architectures that
support CONFIG_COMPAT set it, but future 64-bit architectures will not
(tile would not have needed it either, but got removed).
As older 32-bit architectures get converted to using CONFIG_64BIT_TIME,
they will have to use __ARCH_WANT_SYS_UTIME32 instead of
__ARCH_WANT_SYS_UTIME. Architectures using the generic syscall ABI don't
need either of them as they never had a utime syscall.
Since the compat_utimbuf structure is now required outside of
CONFIG_COMPAT, I'm moving it into compat_time.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
changed from last version:
- renamed __ARCH_WANT_COMPAT_SYS_UTIME to __ARCH_WANT_SYS_UTIME32
The sys_llseek sytem call is needed on all 32-bit architectures and
none of the 64-bit ones, so we can remove the __ARCH_WANT_SYS_LLSEEK guard
and simplify the include/asm-generic/unistd.h header further.
Since 32-bit tasks can run either natively or in compat mode on 64-bit
architectures, we have to check for both !CONFIG_64BIT and CONFIG_COMPAT.
There are a few 64-bit architectures that also reference sys_llseek
in their 64-bit ABI (e.g. sparc), but I verified that those all
select CONFIG_COMPAT, so the #if check is still correct here. It's
a bit odd to include it in the syscall table though, as it's the
same as sys_lseek() on 64-bit, but with strange calling conventions.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While converting compat system call handlers to work on 32-bit
architectures, I found a number of types used in those handlers
that are identical between all architectures.
Let's move all the identical ones into asm-generic/compat.h to avoid
having to add even more identical definitions of those types.
For unknown reasons, mips defines __compat_gid32_t, __compat_uid32_t
and compat_caddr_t as signed, while all others have them unsigned.
This seems to be a mistake, but I'm leaving it alone here. The other
types all differ by size or alignment on at least on architecture.
compat_aio_context_t is currently defined in linux/compat.h but
also needed for compat_sys_io_getevents(), so let's move it into
the same place.
While we still have not decided whether the 32-bit time handling
will always use the compat syscalls, or in which form, I think this
is a useful cleanup that we can merge regardless.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have four generations of stat() syscalls:
- the oldstat syscalls that are only used on the older architectures
- the newstat family that is used on all 64-bit architectures but
lacked support for large files on 32-bit architectures.
- the stat64 family that is used mostly on 32-bit architectures to
replace newstat
- statx() to replace all of the above, adding 64-bit timestamps among
other things.
We already compile stat64 only on those architectures that need it,
but newstat is always built, including on those that don't reference
it. This adds a new __ARCH_WANT_NEW_STAT symbol along the lines of
__ARCH_WANT_OLD_STAT and __ARCH_WANT_STAT64 to control compilation of
newstat. All architectures that need it use an explict define, the
others now get a little bit smaller, and future architecture (including
64-bit targets) won't ever see it.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Catch up with the new binding of the Denali IP where three clocks,
"nand", "nand_x", "ecc" are required.
For UniPhier SoCs, the "nand_x" and "ecc" are tied up because they
are both 200MHz.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the r8a7795 and r8a7796 device trees over to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS0 and IPMMU-DS1
following the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Browsing the DTS for all the R-Car SoCs with similar part numbers
makes my head hurt, so to improve the user friendliness of the
DTS code base include R-Car product name in each DTSI file.
Product names are derived from
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe RWDT in the R8A77980 SoC device tree.
Enable RWDT on the Condor and V3H Starter Kit boards.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the Renesas RZ/G2M (R8A774A1) SoC in the ARM64 defconfig.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Christoph Hellwig suggested a slightly different path for handling
backwards compatibility with the 32-bit time_t based system calls:
Rather than simply reusing the compat_sys_* entry points on 32-bit
architectures unchanged, we get rid of those entry points and the
compat_time types by renaming them to something that makes more sense
on 32-bit architectures (which don't have a compat mode otherwise),
and then share the entry points under the new name with the 64-bit
architectures that use them for implementing the compatibility.
The following types and interfaces are renamed here, and moved
from linux/compat_time.h to linux/time32.h:
old new
--- ---
compat_time_t old_time32_t
struct compat_timeval struct old_timeval32
struct compat_timespec struct old_timespec32
struct compat_itimerspec struct old_itimerspec32
ns_to_compat_timeval() ns_to_old_timeval32()
get_compat_itimerspec64() get_old_itimerspec32()
put_compat_itimerspec64() put_old_itimerspec32()
compat_get_timespec64() get_old_timespec32()
compat_put_timespec64() put_old_timespec32()
As we already have aliases in place, this patch addresses only the
instances that are relevant to the system call interface in particular,
not those that occur in device drivers and other modules. Those
will get handled separately, while providing the 64-bit version
of the respective interfaces.
I'm not renaming the timex, rusage and itimerval structures, as we are
still debating what the new interface will look like, and whether we
will need a replacement at all.
This also doesn't change the names of the syscall entry points, which can
be done more easily when we actually switch over the 32-bit architectures
to use them, at that point we need to change COMPAT_SYSCALL_DEFINEx to
SYSCALL_DEFINEx with a new name, e.g. with a _time32 suffix.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Link: https://lore.kernel.org/lkml/20180705222110.GA5698@infradead.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Configure sdmmc4 parent clock to pllc4 and sdmmc1 to pllp_out0 by
setting the assigned-clocks device tree properties. pllc4 offer
better jitter performance and should be used with higher speed
modes like HS200 and HS400.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use assigned-clock properties to configure pllc4 as the parent clock
for sdmmc4 on Tegra210. pllc4 offers better jitter perfomance than
the default pllp and is required by HS200 and HS400 modes.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the calibration offset properties used for automatic pad drive
strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the calibration offset properties used for automatic pad drive
strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Allow sdmmc1 to set the signaling voltage to 1.8 V in order to support
faster signaling modes.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On p2180 sdmmc4 is powered from a fixed 1.8 V regulator.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set regulator-min-microvolt property of ldo2 to 1.8 V in
tegra210-p2180.dtsi. ldo2 is used by the sdmmc1 SDHCI controller and its
voltage needs to be adjusted down to 1.8 V to support faster signaling
modes. It appears that the comment about the SDHCI driver requesting
invalid voltages no longer applies.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add pad voltage configuration nodes for sdmmc pads with configurable
voltages on Tegra186.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add pad voltage configuration nodes for sdmmc pads with configurable
voltages on Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Beside the non-controllable green power LED, the NanoPi-A64 features a
blue "status" LED, connected to PD24.
Add the device tree node to make it usable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The NanoPi-A64 has an on-board WiFi chip, connected to the usual MMC1 SDIO
interface. The AXP power line is the always-on VDD_SYS_3.3V, but it uses
pin L2 to enable the regulator.
As the actual WiFi driver is not in mainline Linux, it doesn't have a
compatible string, so we omit this from the node.
Add the respective nodes to the DT to make it usable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Add RTL8189ETV LPO clock to pwrseq node]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The NanoPi-A64 has the usual Realtek Gbit PHY connected to the EMAC,
so add the respective nodes to the DT. The PHY is powered by the
VDD_SYS_3.3V line, which is always on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Olinuxino has two USB sockets:
USB0 is connected to a micro B socket. As it has the ID pin wired and
the VBUS line connected to the PMIC, we describe it as a proper OTG socket,
which switches between host and device automatically.
USB1 is connected to a normal USB A socket. PG9 enables the power line,
so add the required regulator as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the DT nodes required to enable the Gigabit Ethernet on the board.
The PHY is powered by the always-on power rail VDD_SYS_3.3V (DCDC1).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win board uses the AXP's ALDO1 power rail to drive the
VCC-CSI line, which, according to the schematic, needs to be set to 2.8V.
Also the ELDO3 power rail is connected to the CSI, with somewhat unclear
voltage requirements. Add this regulator and allow the voltage to be set
between 1.5V and 1.8V, which are the voltages mentioned in the
schematic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win comes with 2 MB SPI flash, add the node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win features a soldered WiFi chip on the board, connected
via the SDIO interface. Add the required DT nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a green status LED, add the DT node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Antoine Tenart