Create mpc8548cds_36b.dts. Support 36-bit mode.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Create mpc8548cds.dtsi
* Move lbc, soc and pci0 nodes to mpc8548cds_32b.dtsi
* Change cuImage.mpc8548cds to cuImage.mpc8548cds_32b
* Rename mpc8548cds.dts to mpc8548cds_32b.dts
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove FPGA(CADMUS) macros in code. Move it to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct ethernet1 and add ethernet2 and ethernet3.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the compatible string of sec 4.0 to match with CAAM driver according
to Documentation/devicetree/bindings/crypto/fsl-sec4.txt
Signed-off-by: Liu Shuo <shuo.liu@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc836x_mds platform has been broken since the commit
6fe3264945
"netdev/phy: Use mdiobus_read() so that proper locks are taken"
which caused the fsl_pq_mdio TBI autoprobe to oops. The oops
was "fixed" in commit 28d8ea2d56
"fsl_pq_mdio: Clean up tbi address configuration"
by simply removing the the autoscan code, and making tbi nodes
mandatory. Some of the newer reference platforms were updated
to have tbi nodes in 220669495b
"powerpc: Add TBI PHY node to first MDIO bus"
but the older mpc836x didn't get one and hence was just failing
with -EBUSY as follows:
fsl-pq_mdio: probe of e0102120.mdio failed with error -16
...
net eth0: Could not attach to PHY
eth0: Cannot initialize PHY, aborting.
Add a TBI node and use the 1st free address for it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NOR flash, need to be disabled.
This also means that the localbus is not a 'simple-bus' any more, so remove
that string from the compatible node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Create a 32-bit address space version of p1022ds.dts. To avoid confusion,
p1022ds.dts is renamed to p1022ds_36b.dts. We also create p1022ds.dtsi
to store some common nodes.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The properties indicates that the hardware supports waking up via magic
packet.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo introduced by "powerpc: Add TBI PHY node to first MDIO bus"
from Andy Fleming.
It's device_type rather than device-type, which causes the mdio probe to
fail thus making all gianfar ethernet interfaces unusable.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is here most likely since the FSL bsp. Back in the FSL bsp it was
set to 50Mhz and working. However the driver divided the SoC freq. only
by 2. According to the TRM the platform clock (which the manual refers
in its formula) is the system clock divided by two. So in the end it has
to divide by 4 and this is what the fsl-spi driver in tree is doing.
Since then the flash is not wokring I guess. After chaning the freq from
50Mhz to 40Mhz like others do then I can access the flash.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is not at 0xffa00000. According to current u-boot source the NAND
controller is always at 0xff800000 and it is either at CS0 or CS1
depending on NAND or NAND+NOR mode. In 36bit mode it is shifted to
0xfff800000 but it has always an eight there and never an A.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add usb controller version info for the following:
MPC8536, P1010, P1020, P1021, P1022, P1023, P2020, P2041,
P3041, P3060, P5020
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
- x1 PCIe slot or x1 PCIe to dual SATA controller
- x1 mini-PCIe slot
USB 2.0
- ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic’s GL850A
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This compatible value will be used to distinguish some special features of APM821XX EMAC: no half duplex mode support, configuring jumbo frame.
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FreeScale PowerQUICC-III-compatible (mpc85xx/mpc86xx) MPICs do not
correctly report the number of hardware interrupt sources, so software
needs to override the detected value with "256".
To avoid needing to write custom board-specific code to detect that
scenario, allow it to be easily overridden in the device-tree.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale MPIC (and perhaps others in the future) is incapable of
routing non-IPI interrupts to more than once CPU at a time. Currently
all of the Freescale boards msut pass the MPIC_SINGLE_DEST_CPU flag to
mpic_alloc(), but that information should really be present in the
device-tree.
Older board code can't rely on the device-tree having the property set,
but newer platforms won't need it manually specified in the code.
[BenH: Remove unrelated changes, folded in a different patch]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MPIC code checks for a "big-endian" property and sets the flag
MPIC_BIG_ENDIAN if one is present, although prior to the "mpic->flags"
fixup that would never have worked anways.
Unfortunately, even now that it works properly, the Freescale mpic
device-node (the "PowerQUICC-III"-compatible one) does not specify it,
so all of the board ports need to manually pass it to mpic_alloc().
Document the flag and add it to the pq3 device tree. Existing code will
still need to pass the MPIC_BIG_ENDIAN flag because their dtb may not
have this property, but new platforms shouldn't need to do so.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable USB2 controller node for P1020RDB. USB2 controller is used only
when board boots from SPI or SD as it is muxed with eLBC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to latest kernel, the auto-cmd12 property should be
"sdhci,auto-cmd12", and according to the SDHC binding and the workaround for
the special chip, add the chip compatible for eSDHC: "fsl,p1022-esdhc",
"fsl,mpc8536-esdhc", "fsl,p1020-esdhc", "fsl,p2020-esdhc" and
"fsl,p1010-esdhc".
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: Use dtc's -d (dependency) option
dtc: Implement -d option to write out a dependency file
kbuild: Fix comment in Makefile.lib
scripts/genksyms: clean lex/yacc generated files
kbuild: Correctly deal with make options which contain an "s"
This hooks dtc into Kbuild's dependency system.
Thus, for example, "make dtbs" will rebuild tegra-harmony.dtb if only
tegra20.dtsi has changed yet tegra-harmony.dts has not. The previous
lack of this feature recently caused me to have very confusing "git
bisect" results.
For ARM, it's obvious what to add to $(targets). I'm not familiar enough
with other architectures to know what to add there. Powerpc appears to
already add various .dtb files into $(targets), but the other archs may
need something added to $(targets) to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
[mmarek: Dropped arch/c6x part to avoid merging commits from the middle
of the merge window]
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features. Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCI ranges, localbus reg and localbus chip-select 2 range do not match
the memory map setup by bootloader.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.
The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit c55aef0e5b ("powerpc/boot: Change the load address
for the wrapper to fit the kernel") introduced a WARNING to
inform the user that the uncompressed kernel would overlap
the boot uncompressing wrapper code. Change it to an INFO.
I initially thought, this would be a 'WARNING' for the those
boards, where the link_address should be fixed, so that the
user can take actions accordingly.
Changing the same to INFO.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The wrapper code which uncompresses the kernel in case of a 'ppc' boot
is by default loaded at 0x00400000 and the kernel will be uncompressed
to fit the location 0-0x00400000. But with dynamic relocations, the size
of the kernel may exceed 0x00400000(4M). This would cause an overlap
of the uncompressed kernel and the boot wrapper, causing a failure in
boot.
The message looks like :
zImage starting: loaded at 0x00400000 (sp: 0x0065ffb0)
Allocating 0x5ce650 bytes for kernel ...
Insufficient memory for kernel at address 0! (_start=00400000, uncompressed size=00591a20)
This patch shifts the load address of the boot wrapper code to the next
higher MB, according to the size of the uncompressed vmlinux.
With the patch, we get the following message while building the image :
WARN: Uncompressed kernel (size 0x5b0344) overlaps the address of the wrapper(0x400000)
WARN: Fixing the link_address of wrapper to (0x600000)
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.
This adds it using ppc40x_simple and provides a device-tree.
There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.
The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.
CC: devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
In this situation, the pixis supports "indirect mode", which allows access
to the pixis itself by reading/writing addresses on specific local bus
chip selects. CS0 is used to select which pixis register to access, and
CS1 is used to read/write the value.
To support this, we introduce another board-control child node of the
localbus node that contains a 'reg' property for CS0 and CS1. This will
produce the correct physical addresses for CS0 and CS1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update all dts files that support SRIO controllers to match the new
fsl,srio device tree binding.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p5020-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p4080-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3060-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
* Fixed l3-cache IRQs, we have 2 CPCs, so we should have IRQs for both
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Fixed some dcsr compatiable typo's from 'p43041' to 'p3041'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p2041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 &
* etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 & etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1023-IP..." from compatibles for standard blocks
* Removed incorrect power/pmc node, there are no etsec on P1023
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Updated spi node to new espi binding specification
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1022-IP..." from compatibles for standard blocks
* Fixed bug in local bus range node for CS2, was maping to
0x0 0x0xffa00000 instead of 0xf 0xffa00000
* Fixed localbus reg property should have been 0xf 0xffe05000
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Timur Tabi <timur@freescale.com>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Dropping "fsl,p1020-IP..." from compatibles for standard blocks
* Fixed PCIe interrupt-maps to have proper number of cells
* Added mdio node for etsec@26000
* Added usb node for 2nd usb controller
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1010-IP..." from compatibles for standard blocks
* PCI interrupt map - wrong IRQs for PCI-0 controller
* SDHC interrupt sense was wrong
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8572 SoC template
* Dropping "fsl,mpc8572-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Dropping "fsl,mpc8569-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Dropping "fsl,mpc8568-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Moved mdio nodes up one level instead of under tsec nodes
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Added MPIC / PCIe msi node
* Dropping "fsl,mpc8548-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Updated ethernet 'model' to 'eTSEC' as that's what on MPC8544
* Dropping "fsl,mpc8544-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
* and moved
PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8536 SoC template
[ marked as MPC8572 compatiable to get errata handling that applies ]
* Added missing cache-line-size & cache-size properties missing from
L2-cache node
* Added IP level IEEE 1588 / ptp timer node
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce some common components that we can utilize to build up the
various PQ3/85xx device trees.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* set interrupt-parent at root so its not duplicate in every node
* Add mpic timers
* Move to 4-prop cells for mpic timer
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move SoC specific details like irq mapping to SoC dtsi
* Update interrupt property to cover both error interrupt and PCIe
runtime interrupts
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we include the p1020rdb.dts instead of p1020si.dts we greatly reduce
duplication and maintenance. We can just list which devices are
disabled for the given core and mpic protected sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers. As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).
IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
P3060QDS Board Overview:
Memory subsystem:
- 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
- 128M Bytes NOR flash single-chip memory
- 16M Bytes SPI flash
- 8K Bytes AT24C64 I2C EEPROM
Ethernet:
- 4x1G + 4x1G/2.5G Ethernet controllers
- 2xRGMII + 1xMII, three VSC8641 PHYs on board
- Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C: Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GE DTBs were not updated when the Gianfar driver was converted to an
of_platform_driver in commit b31a1d8b41. Update
the DTBs, adding the required TBI entries.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding new device tree binding file for the DCSR node. Modifying device
tree dtsi files to add DCSR node for P2041, P3041, P4080, & P5020.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Standarize and document the FPGA nodes used on Freescale QorIQ reference
boards. There are different kinds of FPGAs used on the boards, but
only two are currently standard: "pixis", "ngpixis", and "qixis". Although
there are minor differences among the boards that have one kind of FPGA, most
of the functionality is the same, so it makes sense to create common
compatibility strings.
We also need to update the P1022DS platform file, because the compatible
string for its PIXIS node has changed. This means that older kernels are
not compatible with newer device trees. This is not a real problem, however,
since that particular function doesn't work anyway. When the DIU is active,
the PIXIS is in "indirect mode", and so cannot be accessed as a memory-mapped
device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc. Use the core name to be
consistent going forward.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
timer0 and timer1 pins are used as simple GPIO on this board.
Add gpio-controller and #gpio-cells properties to timer nodes
so that we can control gpio lines using available MPC52xx
GPT driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add new nodes to describe more hardware the board is
equipped with:
- two can nodes for SJA1000 on localbus
- pci node to support Coral-PA graphics controller
- serial node for SC28L92 DUART on localbus
- spi node for MSP430 device
Also correct i2c eeprom node name.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This adds a skeletton for the new Power "Non Virtualized"
platform which will be used by machines supporting running
without an hypervisor, for example in order to run KVM.
These machines will be using a new firmware called OPAL
for which the support will be provided by later patches.
The PowerNV platform is intended to be also usable under
the BML environment used internally for early CPU bringup
which is why the code also supports using RTAS instead of
OPAL in various places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the build can (very rarely) fail to build because libfdt.h has
not been created or is in the process of being copied.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Taishan (440GX) has the first PHY (EMAC2) mapped at PHY address 1
and the 2nd PHY (EMAC3) at PHY address 3. Use "phy-address" to
correctly describe this instead of "phy-map".
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For AMP, different kernel instances load into separate memory regions.
Read the start of memory from the device tree and limit the memory to what's
specified in the device tree.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
On P1022DS both ethernet controllers are connected to RGMII PHYs
accessible via MDIO bus. Remove fixed-link property from ethernet
nodes as they only required when fixed link PHYs without MDIO bus
are used.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This will allow the new HW RNG driver to bind on these boards
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Sequoia board has a Security function IP block on it that contains a TRNG.
Add the crypto and rng portions of that IP block to the DTS.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl-lbc driver requires an interrupt to bind to localbus device.
Populate 85xx boards' dts trees with lbc interrupt info.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Added BSD dual-license
* Moved mpic-parent to root so we dont need to duplicate everywhere
* Added next level cache from L2 to CPC
* Moved to 4-cell MPIC interrupt properties
* Added 3 MSI banks
* Added numerous missing nodes: soc-sram-error, guts, pins, clockgen,
rcpm, sfp, serdes, etc.
* Reworked PCIe interrupts to be at virtual bridge level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic device tree for P3041DS board. This device tree excludes
support for DPAA and RapidIO nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic device tree for P5020DS board. This device tree excludes
support for DPAA and RapidIO nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the Freescale P1022DS reference board, the SSI audio controller is
connected in "asynchronous" mode to the codec's clocks, so the device tree
needs an "fsl,ssi-asynchronous" property.
Also remove the clock-frequency property from the wm8776 node, because
the clock is enabled only if U-Boot enables it, and U-Boot will set the
property if the clock is enabled. A future version of the P1022DS audio
driver will configure the clock itself, but for now, the driver should
not be told that the clock is running when it isn't.
Also fix the FIFO depth to 15, instead of 16.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
dtc was moved and .gitignores have been added to the new location. So, we can
delete the old, forgotten ones.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds MSI support for 440SPe, 460Ex, 460Sx and 405Ex.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The eTSEC includes a PTP clock with quite a few features. This patch adds
support for the basic clock adjustment functions, plus two external time
stamps, one alarm, and the PPS callback.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (45 commits)
crypto: caam - add support for sha512 variants of existing AEAD algorithms
crypto: caam - remove unused authkeylen from caam_ctx
crypto: caam - fix decryption shared vs. non-shared key setting
crypto: caam - platform_bus_type migration
crypto: aesni-intel - fix aesni build on i386
crypto: aesni-intel - Merge with fpu.ko
crypto: mv_cesa - make count_sgs() null-pointer proof
crypto: mv_cesa - copy remaining bytes to SRAM only when needed
crypto: mv_cesa - move digest state initialisation to a better place
crypto: mv_cesa - fill inner/outer IV fields only in HMAC case
crypto: mv_cesa - refactor copy_src_to_buf()
crypto: mv_cesa - no need to save digest state after the last chunk
crypto: mv_cesa - print a warning when registration of AES algos fail
crypto: mv_cesa - drop this call to mv_hash_final from mv_hash_finup
crypto: mv_cesa - the descriptor pointer register needs to be set just once
crypto: mv_cesa - use ablkcipher_request_cast instead of the manual container_of
crypto: caam - fix printk recursion for long error texts
crypto: caam - remove unused keylen from session context
hwrng: amd - enable AMD hw rnd driver for Maple PPC boards
hwrng: amd - manage resource allocation
...
Create the dts files for each core and splits the devices between the two
cores for P1020RDB.
Core0 has core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb, eth1,
eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
Core1 has l2, eth0, crypto.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Fix compatible property for global-util node of P1020si.dtsi.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCIe device in legacy mode can trigger interrupts using the wires #INTA,
#INTB ,#INTC and #INTD. PCI devices are obligated to use #INTx for
interrupts under legacy mode. Each PCI slot or device is typically wired
to different inputs on the interrupt controller.
So, Define interrupt-map and interrupt-map-mask properties for device tree
to of map each PCI interrupt signal to the inputs of the interrupt
controller.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Creates P2020si.dtsi, containing information for P2020 SoC. Modifies dts
files for P2020 based systems to use dtsi file.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Creates P1020si.dtsi, containing information for the P1020 SoC. Modifies dts
files for P1020 based systems to use dtsi file
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Grant Likely <grant.likelY@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is no hardware interrupt 0xf7. But now we can express the timer
interrupt using 4-cell interrupts. This requires converting all of the
other interrupt specifiers in the tree as well.
Also add the second timer group, and fix the reg property to only
describe the timer registers.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The timestamps recorded in the .gz files add no value.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a first cut at making bootwrapper code which will
produce a zImage compliant with the requirements set down
by ePAPR.
This is a very simple bootwrapper, taking the device tree
blob supplied by the ePAPR boot program and passing it on
to the kernel. It builds on the earlier patch to build a
relocatable ET_DYN zImage to meet the other ePAPR image
requirements.
For good measure we have some paranoid checks which will
generate warnings if some of the ePAPR entry condition
guarantees are not met.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds code, linker script and makefile support to allow
building the zImage wrapper around the kernel as a position independent
executable. This results in an ET_DYN instead of an ET_EXEC ELF output
file, which can be loaded at any location by the firmware and will
process its own relocations to work correctly at the loaded address.
This is of interest particularly since the standard ePAPR image format
must be an ET_DYN (although this patch alone is not sufficient to
produce a fully ePAPR compliant boot image).
Note for now we don't enable building with -pie for anything.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PCIe memory address space is 1:1 mapped with u-boot.
Update dts of Px020RDB i.e. P1020RDB and P2020RDB to match the address map
changes in u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- all the integration parameters have been captured by the binding.
- the block name really uniquely identifies this hardware.
Some advocate putting SoC names everywhere in case software needs
to work around some chip-specific bug, but more precise SoC
information already exists in SVR, and board information already
exists in the top-level device tree node.
Note that sometimes the SoC name is a worse identifier than the
block version, as the block version can change between revisions
of the same SoC.
As a matter of historical reference, neither SEC versions 2.x
nor 3.x (driven by talitos) ever needed CHIP references.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Help clarify that the number trailing in compatible nomenclature
is the version number of the device, i.e., change:
"fsl,p4080-sec4.0", "fsl,sec4.0";
to:
"fsl,p4080-sec-v4.0", "fsl,sec-v4.0";
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Steve Cornelius <sec@pobox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine. Its programming model is
incompatible with all prior versions of the SEC (talitos).
The SEC4 is also known as the Cryptographic Accelerator
and Assurance Module (CAAM); this driver is named caam.
This initial submission does not include support for Data Path
mode operation - AEAD descriptors are submitted via the job
ring interface, while the Queue Interface (QI) is enabled
for use by others. Only AEAD algorithms are implemented
at this time, for use with IPsec.
Many thanks to the Freescale STC team for their contributions
to this driver.
Signed-off-by: Steve Cornelius <sec@pobox.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update p1022 sata compatible to "fsl,p1022-sata", "fsl,pq-sata-v2".
p1022ds sata controller is v2 version comparing previous FSL sata
controller, for example, mpc8536.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC852 based mgsuvd board from Keymile was initially ported,
but later on not developed further. This patch removes the respective
files to decrease merging conflicts and unneeded maintenance.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mgcoge board from keymile is now base for some other
similar boards. Therefore the board specific name mgcoge
was renamed to a generic name km82xx. Additionally some
enhancements were made:
- rework partition table in dts file
- add cpm2_pio_c gpio controller in dts file
- update defconfig
- add pin description for SCC1
- add pin description and configuration for USB
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Beside the MPC 8360 based board kmeter1 other km83xx boards
from keymile will follow. Therefore the board specific naming
kmeter1 for functions and files were replaced with km83xx.
Additionally some updates were made:
- update defconfig for 2.6.38
- rework flash partitioning in dts file
- add gpio controller for qe_pio_c in dts
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fix is a reset for USB PHY that requires some amount of time for power
to be stable on Canyonlands.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The dts-installed variable is initialised using a wildcard path that
will be expanded relative to the build directory. Use the existing
variable dtstree to generate an absolute wildcard path that will work
when building in a separate directory.
Reported-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Gerhard Pircher <gerhard_pircher@gmx.net> [against 2.6.32]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Zhao Chenhui