Amarula A64-Relic board by default bound with OV5640 camera,
so add support for it with below pin information.
- PE13, PE12 via i2c-gpio bitbanging
- CLK_CSI_MCLK as external clock
- PE1 as external clock pin muxing
- ALDO1 as AVDD supply
- DLDO3 as DOVDD supply
- ELDO3 as DVDD supply
- PE14 gpio for reset pin
- PE15 gpio for powerdown pin
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some camera modules have the SoC feeding a master clock to the sensor
instead of having a standalone crystal. This clock signal is generated
from the clock control unit and output from the CSI MCLK function of
pin PE1.
Add a pinmux setting for it for camera sensors to reference.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to the device tree specification, any bus should have a 'bus'
node name.
Since it isn't the case for us on the DE2 bus, fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
MMC1 is used on some H6 boards we want to support. Typical use is 4-bit
SDIO interface with a WiFi chip. Add pin definitions for this use case.
As this is the only possible configration for mmc1, make it the default
one, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe
Add basic support for the board.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinmuxing available for each MMC controller.
Move the pinctrl to the SOC
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The device tree binding already lists compatible strings for H6
SoC, so add a device node for it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The I2S binding never mentions a reset-names property, or mentions which
value it should have. To avoid any further issue, remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The H3 and H5 have never been converted to the new convention we want to
have for the pinctrl nodes.
Convert them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some nodes still have pinctrl-names entry, yet they don't have any pinctrl
group anymore. Drop them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some pinctrl node names for the A64 and H6 do not follow the convention
that we switched to and enforced, most notably by using underscores in node
names, which also trigger a DTC warning.
Let's change that.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The pinctrl binding mandates that we have the three clocks fed into the PIO
described.
Even though the old case is still supported for backward compatibility, we
should update our DTs to fix this.
Fixes: 6bc37fac30 ("arm64: dts: add Allwinner A64 SoC .dtsi")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit a7f7047ffc ("arm64: dts: allwinner: a64: Add cross links for the
mixers") introduced a few errors while fixing the cross links. Make sure to
correct them.
Fixes: a7f7047ffc ("arm64: dts: allwinner: a64: Add cross links for the mixers")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 datasheet lists the supply rail for the headphone amp's charge
pump as "CPVDD". cpvdd-supply is the name of the property for this power
rail specified in the device tree bindings. "HPVCC" was the name used in
the A33 datasheet for the same function.
Rename the supply so it matches the datasheet and bindings.
Fixes: c56689e6f2 ("arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec")
Fixes: 6de8e71784 ("arm64: dts: allwinner: a64: enable sound on Pinebook")
Fixes: 498c21f233 ("arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The device tree binding already lists compatible strings for these two
SoCs. Add a device node for them.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This adds the Video engine node for H6. It can use whole DRAM range so
there is no need for reserved memory node.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike what the binding for multiple pipeline documents, the A64 doesn't
have the cross links between the TCON and the mixers.
Let's add them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Amarula A64 Relic has STLM75 sensor for digital temperature
and thermal watchdog.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable pwm and add a pretty standard backlight node.
The regulator is always on, but we include it anyway, because it is
required by the binding document.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for
Rich Graphics Applications".
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power
Tools GmbH, based on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based
machine used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed
ast2500 baseboard management controller. This is for running on
the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet
switch used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development
system in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely
virtual platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both
in 32-bit and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a,
in 96Boards enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes include
updates for
- STMicroelectronics stm32mp1, which was now formally
launched last week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1goV
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
Our usual round of DT changes for the arm64 Allwinner SoCs:
- Enabling of the various power supplies on most a64 boards
- H6 SRAM controller support
- A64 CSI support
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXF1ZiQAKCRDj7w1vZxhR
xeeaAQCuII0MyMyRYhk4XPkjRncEks7A1Fp7u1kjR4VjbNq8JQD+OhCbKMAz4DVv
T7DeI92HwEO2Dx/ggNMVYDCUDyH55gI=
=Pd5b
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner arm64 DT changes for 5.1, take 2
Our usual round of DT changes for the arm64 Allwinner SoCs:
- Enabling of the various power supplies on most a64 boards
- H6 SRAM controller support
- A64 CSI support
* tag 'sunxi-dt64-for-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Enable PMIC power supplies on various boards
arm64: dts: allwinner: a64: teres-i: enable power supplies
arm64: dts: allwinner: h6: Add support for the SRAM C1 section
dt-bindings: sram: sunxi: Add compatible for the H6 SRAM C1
arm64: dts: allwinner: a64: Add A64 CSI controller
arm64: dts: allwinner: h6: Move GIC device node fix base address ordering
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Our usual round of DT changes shared between arm and arm64.
We have a bunch of changes for board, improving the eMMC support on the H5
variant of the All-H3-CC, enabling HDMI and reworking the CSI driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXF1X8QAKCRDj7w1vZxhR
xX9ZAP9KwFKKehrS1QJjTHKeowUKEnRHuDj2MlwTZJgCw/AMMgEAzgRZwY/VH/Os
aQIhJho9hWmBE0dePIZuWzzCp1giNw8=
=7jQV
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner H3 and H5 changes for 5.1
Our usual round of DT changes shared between arm and arm64.
We have a bunch of changes for board, improving the eMMC support on the H5
variant of the All-H3-CC, enabling HDMI and reworking the CSI driver.
* tag 'sunxi-h3-h5-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: libretech-all-h3-cc: Mark eMMC HS-DDR 3.3V capable
ARM: dts: sunxi: h3/h5: Drop A31 fallback compatible for CSI controller
ARM: dts: sun8i-h3: nanopi-m1-plus: enable HDMI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Libre Computer ALL-H3-CC H5 is one of the few boards that can have
its eMMC run at HS-DDR speed mode. Mark it as such.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On these A64 devices, the DC input jacks are wired to the ACIN pins of
the PMIC, which is represented by the AC power supply. With the
exception of the Nanopi A64, all devices include LiPo batteries or have
connectors for them, which are represented by the battery power supply.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
-----BEGIN PGP SIGNATURE-----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=kZwf
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT64 changes for 5.1
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
* tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Enable A64 timer workaround
arm64: dts: allwinner: a64: Fix a typo
arm64: dts: allwinner: a64: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a node for H6 SRAM C1 section.
Manual calls it VE SRAM, but for consistency with older SoCs, SRAM C1
name is used.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add dts node details for Allwinner A64 CSI controller.
A64 CSI has similar features as like in H3, but the CSI_SCLK
need to update it to 300MHz than default clock rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GIC device node was placed out of order in the initial device tree
submission. Move it so the nodes are correctly sorted by base address
again.
Fixes: e54be32d02 ("arm64: allwinner: h6: add the basical Allwinner H6 DTSI file")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As instability in the architectural timer has been observed on multiple
devices using this SoC, inluding the Pine64 and the Orange Pi Win,
enable the workaround in the SoC's device tree.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This typo inverted the meaning of the comment, but the rest of the
comment and the code reveal that the regulator in question needs to be
on at all times.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f91 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket")
Cc: stable@vger.kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When introducing the video-codec node for the video engine, the
compatible for the H5 was used instead of the compatible for the
A64. Use the right compatible instead.
Fixes: d60ce24740 ("arm64: dts: allwinner: a64: Add Video Engine node")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is necessary to use 'perf' for cache profiling etc.
Tested on Teres I Laptop.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Bluetooth using a Broadcom (now Cypress) chip connected to an UART on
the Bananapi M64 is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
-----BEGIN PGP SIGNATURE-----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=Ks3Q
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21 - round 2
Bluetooth using a Broadcom (now Cypress) chip connected to an UART on
the Bananapi M64 is enabled using serdev and the updated bindings for
Broadcom Bluetooth. The patch series had been sitting on the mailing
lists for a month, and the driver bits were just merged on 2018/12/19.
* tag 'sunxi-dt64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO2 provides
overall power via VBAT, and DLDO4 provides I/O power via VDDIO. The RTC
clock output provides the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for Bluetooth,
but this is not covered here.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqJJwAKCRDj7w1vZxhR
xTq4AP9SxrPeKDTBD4mKV+PVuJ2qq919M6o+mcxDkCecEMfbagD+JLkt2uGzdpb8
eC6CuieHvJq1y/akfDpRBf0ZZD0/bw0=
=yRd0
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.21
Our usual pull request with the changes shared between the H3 and H5 SoCs.
The major changes for this release are:
- Addition of the video engine for the H5
- H3 Camera support
- New board: Emlid Neutis N5, Mapleboard MP130
* tag 'sunxi-h3-h5-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: Add Video Engine node
ARM/arm64: dts: allwinner: Move H3/H5 syscon label over to soc-specific nodes
arm64: dts: allwinner: h5: Add system-control node with SRAM C1
ARM: dts: sun8i: h3: Fix the system-control register range
ARM: dts: sun8i: Add the H3/H5 CSI controller
ARM: dts: sun8i-h3: Add dts for the Mapleboard MP130
arm64: dts: allwinner: new board - Emlid Neutis N5
dt-bindings: vendor-prefix: new vendor - Emlid
ARM: dts: sun8i-h3: add sy8106a to orange pi plus
Signed-off-by: Olof Johansson <olof@lixom.net>
Our usual set of arm64 DT changes, with the biggest additions being:
- Support for the video decoding engine in the A64
- Support for the audio codec in the A64
- USB Support in the H6
- HDMI Support in the H6
- EMAC Support in the H6
- New board: Orange Pi Lite2
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqGvQAKCRDj7w1vZxhR
xeObAQDZGMVjFjiWlC0jYjBQoCHMf1dlu6iPd4qe8h3GS1XUVQD/c8SJaMj5oLX1
HKjtqQD+sJRUQdcWlwAsqEEKyKUhfQs=
=aAr3
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21
Our usual set of arm64 DT changes, with the biggest additions being:
- Support for the video decoding engine in the A64
- Support for the audio codec in the A64
- USB Support in the H6
- HDMI Support in the H6
- EMAC Support in the H6
- New board: Orange Pi Lite2
* tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (27 commits)
arm64: dts: allwinner: a64: Fix up RTC device node and clock references
arm64: dts: allwinner: a64: Add Video Engine node
arm64: dts: allwinner: a64: Add support for the SRAM C1 section
arm64: dts: allwinner: a64: pinebook: enable power supplies
arm64: dts: allwinner: a64: sopine-baseboard: enable power supplies
arm64: dts: allwinner: axp803: add AC and battery power supplies
arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec
arm64: dts: allwinner: a64: enable sound on Pinebook
arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine
arm64: dts: allwinner: a64: add nodes necessary for analog sound support
arm64: dts: allwinner: h6: orangepi: Add device nodes for LEDs
arm64: dts: allwinner: h6: orangepi: Enable USB 2.0 host and OTG ports
arm64: dts: allwinner: h6: orangepi: Add board-wide 5V regulator
arm64: dts: allwinner: h6: fix EMAC compatible string sequence
arm64: dts: allwinner: a64: Add device node for Mali-400 GPU
dt-bindings: gpu: mali-utgard: Add compatible for A64 Mali
arm64: dts: allwinner: h6: enable USB2 on Pine H64
arm64: dts: allwinner: h6: add USB Vbus regulator for Pine H64
arm64: dts: allwinner: h6: add USB2-related device nodes
arm64: dts: allwinner: h6: Enable HDMI output on Pine H64 board
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The RTC module on the A64 was claimed to be the same as on the A31, when
in fact it is not. It is actually compatible to the H3's RTC. The A64's
RTC has some extra crypto-related registers which the H3's does not, but
the exact function of these is not clear.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The RTC module on the H3 was claimed to be the same as on the A31, when
in fact it is not. The A31 does not have an RTC external clock output,
and its internal RC oscillator's average clock rate is not in the same
range. The H5's RTC has some extra crypto-related registers compared to
the H3. Their exact functions are not clear. Also the RTC-VIO regulator
has different settings.
This patch fixes the compatible string and clock properties to conform
to the updated bindings. The device node for the internal oscillator is
removed, as it is internalized into the RTC device. Clock references to
the IOSC and LOSC are also fixed.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This adds the Video Engine node for the A64. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the description for the SRAM C1 section to the A64 device-tree.
Since there is no entry for this section in the A64 manual, the base
address and size were only verified to be consistent empirically.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds the Video Engine node for the H5. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EMAC driver requires a syscon node to access the EMAC clock
configuration register (that is part of the system-control register
range and controlled). For this purpose, a dummy syscon node was
introduced to let the driver access the register freely.
Recently, the EMAC driver was tuned to get access to the register when
the SRAM driver is registered (as used on the A64). As a result, it is
no longer necessary to have a dummy syscon node for that purpose.
Now that we have a proper system-control node for both the H3 and H5,
we can get rid of that dummy syscon node and have the EMAC driver use
the node corresponding to the proper SRAM driver (by switching the
syscon label over to each dtsi). This way, we no longer have two
separate nodes for the same register space.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the H5-specific system control node description to its device-tree
with support for the SRAM C1 section, that will be used by the video
codec node later on.
The CPU-side SRAM address was obtained empirically while the size was
taken from the documentation. They may not be entirely accurate.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
AXP803 ACIN pins are routed from SOM to the DC jack on the baseboard.
AXP803 charger pins BATSENSE, LOADSENSE, N_BATDRV, LX_CHG, VIN_CHG
and IPSOUT are connected via PMOS driver to SOM VBAT pins. VBAT and
AXP803 TS pins are routed to the baseboard 3-pin battery connector.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Parts of the AXP803 are compatible with their counterparts on the AXP813.
Add DT nodes ADC, GPIO, AC and battery power supplies.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch enables audio via the SoC's internal audio codec. All
relevant device nodes are enabled, and the routing is set to match
the board design. MIC1 is routed to an onboard microphone, with MBIAS
providing power. MIC2 and HP are routed to the 3.5mm headset TRRS jack.
No phantom power is provided to the headset microphone.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pinebook has a headphone jack tied to the HP headphone output of
the SoC, and internal speakers connected to the LINEOUT of the SoC,
through a standalone amplifier.
This commit enables I2S, digital and analog parts of audio codec on
Pinebook, along with a device node for the external amplifier.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: dropped headphone_amp; added headphone amp regulator supply;
fixed speaker_amp node name and sound-name-prefix name]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This commit enables I2S, digital and analog parts of audiocodec on
Pine64 and SoPine boards.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: Dropped headphone_amp; added headphone amp regulator supply]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add nodes for i2s, digital and analog parts of audiocodec on A64.
The routing paths listed are entries connecting the digital and analog
side of the audio codec together. Due to how device tree works, these
must be copied over to each board device tree, in addition to any board
level routes.
The oversampling rate is set to 128, so that when playing back 192 kHz
audio samples, the MCLK runs at the same rate as the module clock, at
24.576 MHz.
The user manual suggests using different oversampling rates for different
sample rates, but that's not possible without a platform-specific machine
driver.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: Lowered oversampling rate to 128; expanded commit message]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Lite 2 and Orange Pi One Plus both have two LEDs, one red
and one green. These are driven directly by GPIO lines in an active high
arrangement. The red LED is labeled "power", so it is set to be on by
default.
Note that the default drive current for the GPIO lines makes the LEDs
very bright.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Orange Pi Lite 2 and Orange Pi One Plus share the same design for
their USB 2.0 ports. VBUS is directly tied to the board wide 5V rail,
which is also directly tied to the DC jack. There is no current limiting
in this design.
This patch enables all the USB 2.0 related device nodes, and sets the
VBUS regulator supplies and OTG ID detection GPIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Orange Pi Lite 2 and Orange Pi One Plus share the same design for
their USB 2.0 ports. VBUS is directly tied to the board wide 5V rail,
which is also directly tied to the DC jack. There is no current limiting
in this design. This 5V rail also supplies the various inputs to the
PMIC.
This patch adds a board wide 5V regulator and sets it as the input to
the PMIC inputs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The SoC-specific compatible should come before the fallback compatible
string when multiple compatible strings are present, but the sequence is
wrong currently on H6 EMAC node (A64 fallback before H6 compatible).
Fix the sequence.
Fixes: c8ced5516d ("arm64: allwinner: h6: add EMAC device nodes")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for Allwinner A64 has Mali-400MP2.
All interrupt lines are mentioned in the manual so used the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 board has both the USB2 OTG pins and the USB2 host pins on H6
SoC wired out to USB Type-A ports.
Enable them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The 5V output of the USB ports on Pine H64 is controlled via a GPIO.
Add the USB Vbus regulator device tree node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner H6 has two USB2 ports, one OTG and one host-only.
Add device tree nodes related to them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pine H64 board has HDMI type A connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds all entries needed for HDMI to function properly.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[added DE3 bus]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.
So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 board has an Ethernet port, which is connected to a
RTL8211E PHY, then the PHY is connected to the MAC on H6 SoC.
Add support for the Ethernet port.
The PHY needs some time to start up, and the time is modelled as enable
ramp delay of the regulator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has an EMAC like the one in A64.
Add device tree nodes for the H6 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis n5 dtsi file for SoM needs
- add neutis devboard dts file
- add neutis devboard target to dtb makefile
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Backlight power is controlled by PH6 GPIO, so add corresponding
regulator-fixed node for it. Otherwise backlight won't light up
if bootloader doesn't enable it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There are close to 800 indivudal changesets in this branch again, which
feels like a lot. There are particularly many changes for the NVIDIA
Tegra platform this time, in fact more than it has seen in the two years
since the v4.9 merge window. Aside from this, it's been fairly normal,
with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi,
Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5
is a minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core
Marvell Armada 8040 network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in
the BMC.
NXP i.MX usually sees a lot of new boards each release. This time there
we only add one minor variant: ConnectCore 6UL SBC Pro uses the same
SoM design as the ConnectCore 6UL SBC Express added later. However,
there is a new chip, the i.MX6ULZ, which is an even smaller variant
of the i.MX6ULL, with features removed. There is also support for the
reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute module
based on bcm2837, it was launched in early 2017 but only now added to
the kernel, both as 32-bit and as 64-bit files, as we tend to do for
Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time
are:
Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana
Pi M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit
Asus Tinker board, the model 'S' based on rk3288, and three now
boards based on the popular RK3399 chip:
ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
Rock960: https://www.96boards.org/product/rock960/
RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and
the RK3399 is the same chip used in several Chromebooks. Finally,
we get support for the PX30 (aka rk3326) chip, which is based on the
low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board
is supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based
on the MT7622 WiFi router platform, and the first product I've seen with
a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2),
another quad-core Cortex-A53 SoC, and its evaluation platform.
On the 32-bit side, we gain support for an actual end-user product,
the Endless Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform. This
chip is commonly known as the Snapdragon 835, and is used in high-end
phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the previously
added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB
Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing files,
the only board that gets added is the Toradex Colibri T20 on Colibri
Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the (formerly
Marvell) Berlin line of set-top-box chips used e.g. in the various Google
Chromecast. Only the .dtsi gets added at this point, no actual machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yaED
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
Our usual set of DT changes for the arm64 Allwinner SoCs.
The most notable things are:
- HDMI support on the A64
- New boards: OrangePi One Plus
-----BEGIN PGP SIGNATURE-----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=sPs9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.20
Our usual set of DT changes for the arm64 Allwinner SoCs.
The most notable things are:
- HDMI support on the A64
- New boards: OrangePi One Plus
* tag 'sunxi-dt64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (28 commits)
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
arm64: dts: allwinner: a64: Enable HDMI output on A64 boards w/ HDMI
arm64: dts: allwinner: a64: Add display pipeline
arm64: dts: allwinner: h6: add system controller device tree node
arm64: dts: allwinner: h6: Add OrangePi One Plus initial support
arm64: dts: allwinner: a64: Rename r_i2c_pins_a label to r_i2c_pl89_pins
arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins
arm64: dts: allwinner: a64: Split out data strobe pin from mmc2 pinmux
arm64: dts: allwinner: a64: NanoPi-A64: Add blue status LED
arm64: dts: allwinner: a64: NanoPi-A64: Add Wifi chip
arm64: dts: allwinner: a64: NanoPi-A64: Add Ethernet
arm64: dts: allwinner: a64: NanoPi-A64: Fix DCDC1 voltage
arm64: dts: allwinner: a64: Olinuxino: enable USB
arm64: dts: allwinner: a64: Olinuxino: add Ethernet nodes
arm64: dts: allwinner: a64: Olinuxino: fix DRAM voltage
arm64: dts: allwinner: a64: Orange Pi Win: Adjust CSI power rails
arm64: dts: allwinner: a64: Orange Pi Win: Add SPI flash node
arm64: dts: allwinner: a64: Orange Pi Win: Add SDIO node
arm64: dts: allwinner: a64: Orange Pi Win: Add LED node
arm64: dts: allwinner: a64: Orange Pi Win: Add UARTs
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.
This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi M2 Plus H5 is a variant of the original Bananapi M2 Plus,
with the H3 SoC replaced with an H5. Everything else is the same.
Add a stub device tree incorporating the shared bananapi-m2-plus dtsi
file.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H5 has a Mali-450 GPU with 4 Pixel Processor cores.
Interestingly, while the datasheet lists an interrupt line for the GPU's
PMU, the hardware block itself doesn't seem to have it. Reads from the
PMU address range all return zero, and writes are ignored.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The PHY found on the A64-OLinuXino requires a TX delay in order to
operate properly. Olimex uses a 600ps second delay in their BSP, and
that has been found to work, so let's use that value in the current
DT.
Signed-off-by: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Enable all necessary device tree nodes and add connector node to device
trees for all supported A64 boards with HDMI.
Jagan, tested on BPI-M64, OPI-Win, A64-Olinuxino, NPI-A64
Vasily, tested on pine64-lts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: squash all board patches altogether and change supply name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner A64 have a display pipeline with 2 mixers/TCONs, the first
TCON is connected to LCD and the second is to HDMI.
The HDMI controller/PHY pair is similar to the one on H3/H5.
Add all required device tree nodes of the display pipeline, including
the TCON0 LCD one and the TCON1 HDMI one.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: refactor commit message and add 1st pipeline]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
As we have already binding for the H6 system controller, add its node
to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[fixed compatible string]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "r_i2c_pins_a" label is renamed to "r_i2c_pl89_pins" to fit our
current style. The node name "i2c" is also changed to "r-i2c-pl89-pins"
to match. The reason for the peculiar name is that the other option for
muxing R_I2C is on the PL0/PL1 pins, so the name has to mention the pin
numbers in addition to the pingroup.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "uart0_pins_a" label is renamed to "uart0_pb_pins" to fit our
current style. The node name "uart0" is also changed to "uart0-pb-pins"
to match.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The eMMC 5.0 standard introduced the data strobe (DS) pin. This pin is
not used for pre-5.0 data modes, nor is it found on pre-5.0 eMMC chips.
On the A64, this pin is muxed with spi0's MISO pin. If the DS pin is
included in the mmc2 pinmux by default, this wil prevent the usage
of both mmc2 and spi0 together.
Instead, split out the DS pin to a separate pinmux that only gets used
by boards that actually have it wired up. Currently supported ones
include the Bananapi M64 and Pine64 Pinebook. These are fixed up.
Fixes: a3e8f49262 ("arm64: allwinner: a64: Add MMC pinctrl nodes")
Fixes: b8bcf0e1b2 ("arm64: allwinner: add BananaPi-M64 support")
Fixes: df35fbcfa3 ("arm64: dts: allwinner: add support for Pinebook")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Beside the non-controllable green power LED, the NanoPi-A64 features a
blue "status" LED, connected to PD24.
Add the device tree node to make it usable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The NanoPi-A64 has an on-board WiFi chip, connected to the usual MMC1 SDIO
interface. The AXP power line is the always-on VDD_SYS_3.3V, but it uses
pin L2 to enable the regulator.
As the actual WiFi driver is not in mainline Linux, it doesn't have a
compatible string, so we omit this from the node.
Add the respective nodes to the DT to make it usable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Add RTL8189ETV LPO clock to pwrseq node]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The NanoPi-A64 has the usual Realtek Gbit PHY connected to the EMAC,
so add the respective nodes to the DT. The PHY is powered by the
VDD_SYS_3.3V line, which is always on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Olinuxino has two USB sockets:
USB0 is connected to a micro B socket. As it has the ID pin wired and
the VBUS line connected to the PMIC, we describe it as a proper OTG socket,
which switches between host and device automatically.
USB1 is connected to a normal USB A socket. PG9 enables the power line,
so add the required regulator as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the DT nodes required to enable the Gigabit Ethernet on the board.
The PHY is powered by the always-on power rail VDD_SYS_3.3V (DCDC1).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win board uses the AXP's ALDO1 power rail to drive the
VCC-CSI line, which, according to the schematic, needs to be set to 2.8V.
Also the ELDO3 power rail is connected to the CSI, with somewhat unclear
voltage requirements. Add this regulator and allow the voltage to be set
between 1.5V and 1.8V, which are the voltages mentioned in the
schematic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win comes with 2 MB SPI flash, add the node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win features a soldered WiFi chip on the board, connected
via the SDIO interface. Add the required DT nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a green status LED, add the DT node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win exposes several UARTs on header pins, and connects one
to the on-board WiFi/Bluetooth chip.
Add the pinmux definitions to the UART nodes, but keep them disabled.
Enable the UART1, which is wired to the Bluetooth chip, and add a serdev
node. There is no binding for the BT8723 yet, so leave this mostly empty
for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has the usual Gigabit PHY connected to the EMAC.
Its power is controlled by GPIO PD14.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a micro USB-B socket, connected to the SoC's
USB-OTG port. Its power is supplied by the AXP PMIC, and the ID pin is
connected to GPIO PH9. It can serve both as a host or a client port.
Add the respective DT nodes to enable it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: enable paired EHCI/OHCI device nodes and regulator supply]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has four standard USB-A sockets, connected to an
on-board USB hub. The hub's and socket's power regulators are enabled by
GPIO PD7.
Add the regulator to the DT to enable the power supply.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Current kernels complain when booting on an A64 Soc:
....
[ 1.904297] cacheinfo: Unable to detect cache hierarchy for CPU 0
....
Not a real biggie on this flat topology, but also easy enough to fix.
Add the L2 cache node and let each CPU point to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently the enabled MMC controllers on Pine H64 do not have bus-width
set, which make them fall back to 1-bit mode and become quite slow.
Fix this by add the corresponding bus-width properties.
Fixes: ecbd611882 ("arm64: allwinner: h6: enable MMC0/2 on Pine H64")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 have a SID controller which consist of EFUSE (starting at 0x200)
and three registers to read/write some of the protected efuses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 board have a MicroSD slot connected to MMC0 controller of
the H6 SoC and a eMMC slot connected to MMC2.
Enable them in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC have 3 MMC controllers.
Add device tree nodes for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 board has an AXP805 PMIC on it, wired up in standalone, or
self-working, mode.
Enable it in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that the device tree binding headers for the R_CCU have been merged,
we can use the macros, instead of raw numbers.
Switch to R_CCU macros for clock and reset indices.
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
On usual A64 board design the power of HDMI controller is connected to
DLDO1 of the AXP803 PMIC. If this regulator is shut down, the HDMI
output will be blank. Therefore the simplefb driver should keep this
regulator on.
Add the regulator to all currently available A64 boards' simplefb_hdmi
device node, if the board is capable of outputing HDMI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As the U-Boot bootloader now is also capable of initialize the HDMI on
A64 boards, add a simplefb device tree node for accessing the HDMI
framebuffer initialized by the bootloader.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we have all necessary parts to enable the DE2 CCU on the Allwinner
A64 SoC, add the needed device tree nodes, including the DE2 CCU itself
and the DE2 bus.
The "mixer0-lcd0" simplefb device node is updated to use the DE2 CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Pine H64 has 3 GPIO-controlled LEDs, which are labeled "heartbeat",
"link", and "status".
Add device nodes for them.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently all ARM kernels will have s2idle enabled if CONFIG_SUSPEND is
present. In this case if the lid is closed, systemd-logind will enter
s2idle mode by default; however there's no possible wakeup source
defined, so the system will enter a forever idle.
Add the lid itself as a wakeup source, thus the system can wakeup when
the lid is opened.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Originally the name of the DLDO3 regulator on TERES-I is "eDP12", which
is not consistent with other regulator names.
Change it to "vdd-edp", in order to make it more consistent.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The card detect GPIO for Sopine and Pine64-LTS is PF6.
Add this to the dts.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a SRAM controller, and in the device tree currently
we have a syscon node to enable EMAC driver to access the EMAC clock
register. As SRAM controller driver can now export regmap for this
register, replace the syscon node to the SRAM controller device node,
and let EMAC driver to acquire its EMAC clock regmap.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Updated compatible string]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:
USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.
Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.
Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.
Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.
Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.
This commit adds basical support for it.
[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A64 SoC features two PWM controllers, which are fully
compatible to the one used in the A13 and H3 chips.
Add the nodes for the devices (one for the "normal" PWM, the other for
the one in the CPUS domain) and the pins their outputs are connected to.
On the A64 the "normal" PWM is muxed together with one of the MDIO pins
used to communicate with the Ethernet PHY, so it won't be usable on many
boards. But the Pinebook laptop uses this pin for controlling the LCD
backlight.
On Pine64 the CPUS PWM pin however is routed to the "RPi2" header,
at the same location as the PWM pin on the RaspberryPi.
Tested on Pinebook and Teres-I
[vasily: fixed comment message as requested by Stefan Bruens, added default
muxing options to pwm and r_pwm nodes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Outside of SOC few chips need external clock source
through RTC example Wifi chip. So RTC clock nodes to
phandle 32kHz external oscillator.
prefix rtc- with clock-output-names defined in
dt-binding to avoid confusion with existing osc32k name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The OrangePi PC2 have an mx25l1606e spi flash.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Sopine and Pine64-LTS have a winbond w25q128 spi flash on spi0.
Add a node for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE0VqZU19dR2zEVaqr0rTAlCFNr3QFAlsCsQwACgkQ0rTAlCFN
r3S9EhAAifnKDgAqWGuLR9xau3nK8CbjSLyFAba9ARdIuwxO3D0p6xgNkogve3o9
huwtx60TPfZeg86e5dqKmuC7gO/AKK0TaFDQcTXR4dEF6eH635J9yh1G5L6LjrLA
X9+EjuIL7a6HgolwyssRLLQETq3w5Pc+xMcoIc0J4ey0a4H8GjvXQWMzB+ytJWA1
Ykih6hMqJiR1VWbqSefx24+4X7RaBSwqu2S/GDk9Fi6Fabg5rbzH2tgolr0fK2BA
QtGx9LvJFsjpUwa2rOBom1EvEOoFri2ef3D06vOq8Nc0UA9G41JkWBXYczxRP1m5
0SEZUybyudIJMn+X3arEOklEEN5dsfzLnbpT7xWgjocPyt1foPtBYg/usPb8bvwn
k58j/nQDDrVPADEonbWmSBJ+5mtGl7pamJtm6GE0kCAe9eG8kLt0mkL5EH4X2Sq2
0P5q6HAjA866IACZzu4CRipXlBNCY+oMXSeaOkOYIfyIshNKkWPyxqim98FDtm6Y
66nfON3yXWOmbWwIW2z7HSJXpIn4L+qMD0OvTZWDISANQWybaKxeytVMcB65iEGQ
LzhfZi8K1tZdTN0cvsdKXrTTMnkcU4a1OZbDLe6vBPAengX219MYu1uCd+ArQ1Md
Rd1rjT+Nv2JpVTFV1AUgeoA1Yhu1Nw1zQTAu5y3d64HJCnybamU=
=d7Ql
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 changes for 4.18
We mostly have some changes to support the H6, Allwinner latest SoC. We're
still in the preliminary phase, with I2C, pinctrl and clock support.
* tag 'sunxi-dt64-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h6: add PCF8563 RTC on Pine H64 board
arm64: allwinner: h6: add R_I2C controller
arm64: allwinner: h6: add R_INTC interrupt controller
arm64: allwinner: h6: add node for R_PIO pin controller
arm64: allwinner: h6: add PRCM CCU device node
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
arm64: dts: allwinner: axp803: Add drivevbus regulator
arm64: allwinner: h6: restore the usage of CCU slice macros
Signed-off-by: Olof Johansson <olof@lixom.net>
Pine H64 board has a PCF8563 dedicated RTC connected to its R_I2C bus.
Enable the R_I2C bus and add the RTC to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_I2C controller wired to the PL0/PL1 pins, which
are used in the reference design to connect AXP805 PMIC.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has also a R_INTC interrupt controller like Allwinner
A64 SoC, but has its base address changed due to the memory map change
in H6.
Add it into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 SoC has a R_PIO pin controller which controls PL and PM
GPIO banks.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 has also a PRCM CCU.
Add its device node into the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H2+, H3,
or H5 SoCs with the same PCB.
The board has 2GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
This patch enables the H5 variant using the H3 board definition moved to
a common dtsi in an earlier patch. The dts simply include the common dtsi
and declares the correct compatible and model of the H5 variant.
Suggested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The dtb entries for NanoPi boards in the device tree makefile somehow
ended up after the Orange Pi boards.
Move them so the list is properly sorted.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
At the board level, we want to be able to specify what regulator
supplies power to the cpu domain.
Add a label to the first cpu node so we can reference it later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add usb otg support for bananapi-m64 board,
- USB-ID connected with PH9
- USB-DRVVBUS controlled by N_VBUSEN pin from PMIC
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add reg_drivevbus regualtor for boards which are using
external regulator to drive the OTG VBus through N_VBUSEN
PMIC pin.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
As the definition of CCU slice macros are already merged into the source
tree, restore the usage of the macros now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
-----BEGIN PGP SIGNATURE-----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=hXvM
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
The Xunlong Orange Pi Zero Plus is single board computer.
- H5 Quad-core 64-bit Cortex-A53
- 512MB DDR3
- microSD slot
- Debug TTL UART
- 1000M/100M/10M Ethernet RJ45
- Realtek RTL8189FTV
- Spi flash (2MB)
- One USB 2.0 HOST, One USB 2.0 OTG
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TERES-I is an open hardware laptop built by Olimex using the
Allwinner A64 SoC.
Add the board specific .dts file, which includes the A64 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 SoC features two display pipelines, one has a LCD output, the
other has a HDMI output.
Add support for simplefb for the LCD output. Tested on Teres I.
This patch was inspired by work of Icenowy Zheng.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a watchdog node for the A64, automatically enabled on all boards.
Since the device is compatible with an existing driver, we only reserve
a new compatible string to be used together with the fall back.
Tested on Olimex Teres-I.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the proper pin group node to reference in board files.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is an Allwinner H6-based SBC from Pine64, with the following
features:
- 1GiB/2GiB/4GiB LPDDR3 DRAM (in 4GiB situation only 3GiB is
accessible)
- AXP805 PMIC
- Raspberry-Pi-compatible GPIO header, "Euler" GPIO header (not
compatible with the "Euler" on Pine A64) and "Expansion" pin header
- 2 USB 2.0 ports and 1 USB 3.0 ports
- Audio jack
- MicroSD slot and eMMC module slot
- on-board SPI NOR flash
- 1Gbps Ethernet port (via RTL8211E PHY)
- HDMI port
Adds initial support for it, including the UART on the Expansion pin
header.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner H6 is a new SoC with Cortex-A53 cores from Allwinner, with its
memory map fully reworked and some high-speed peripherals (PCIe, USB
3.0) introduced.
This commit adds the basical DTSI file of it, including the clock
support and UART support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable HDMI output on all boards with HDMI connector.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the DAI blocks to the device tree. I2S0 and I2S1 are for
connecting to an external codec.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The S/PDIF transmitter can be reached on the Euler connector.
But as this is a GPIO then leave it disabled so that an overlay
can override the status property.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the device tree sound bindings for the S/PDIF block.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block and pin to the A64 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
-----BEGIN PGP SIGNATURE-----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=bDG2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>
The DE2 CCU on Allwinner H5 SoC has a slightly different behavior than
the one on H3, so the compatible string is not set in the common DTSI
file.
Add the compatible string of H5 DE2 CCU in H5 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Bananapi-M64 has 3 LEDS in red, green, and blue. These are toggled
via GPIO lines, which drive transistors that control current across the
LEDS. The red LED is by default on, via an additional pull-up on the
control line. We consider this means that it is a power indicator.
So we set the "default-on" property for it.
The pingroups the GPIO lines belong to require external regulators be
enabled to be able to drive the GPIO high. These regulators also have
other purposes. However the pin controller does not have bindings for
regulators. Here we just set them to always-on.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sdcard detect pin on orange-pi-zero-plus2 is pulled up.
Fix cd-gpio description to enable sdcard detect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators,
replace fixed regulator vcc3v3 with AXP803 dcdc1 regulator where ever
it need to replace.
Tested mmc0 on sopine baseboard.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
add arm64 H5 dwmac-sun8i support for this board
Signed-off-by: Antony Antony <antony@phenome.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PF6 is mostly used as the CD pin for the microSD slot on H5 based
boards. So far we were referencing this pin twice: once using the
mmc0_cd_pin phandle, and then again directly as a GPIO via the pinctrl
phandle.
This will cause problems if the pinctrl driver enables strict mode, as
the second request will fail now, leading to a driver init failure.
Remove the redundant pin reference via the mmc0_cd_pin phandle.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Chris Obbard <obbardc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On several A64 boards the Ethernet PHY is powered by the DC1SW regulator
on the AXP803 PMIC.
Add phy-handle property to these boards' emac node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable AXP803 PMIC and regulators for Orangepi Win.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaDhcfAAoJEGCrR//JCVIngu0QAI2ntVotaOAOaCurNCnoVwI1
j+eKwHGTawQRcSHWN8C+p4FzzaOmw+vvbOyewky8PWaDOCkK6yWEHRf3hb2la2jw
j9prht28R1RAHIRPuah4SxKHYoT4VW9q/2hMHJ2BiNDOMX54xE7j2cUvWSsIRz5o
id2QqKsp2OIDNQAXAA4N25FjdBCYvSik80panSdJITtJODIj6UfmcXSgqkoQ3TTV
rwVyFtryl9Si3eyZYcfB2/0ILKuaMC8gl7IX9z+PkRqu9XN7i6bZKZlMMtpJqX3u
Ad89kLkFqNhiwZ77bIoRRl+0NEoSu5hTPLHRqghS6gPfDY2JT6igf0rGC8twjfea
fzGOBWr6NlIlUmR4smS0GyE/3YsfOQvYWjE+zx5qkmay30TORVTZBzsBR+kQJzKK
tnbO1zvst1ECtk9e8np0di4NAo9rwM37dxpu4aspP1Umxw1K68VSNE3RhGl8UUwW
oNvHa8hD8Ck0QDBNltrkmKBVoIYKRU3XhXrRXVjRQdu6Xitml0XYBi80V0h33EE3
162UXDEMu1/aqRRZUtKw7+yozT8fqOHjH8Zrv2zCVGg0HEwVohcWv/BPXbrg0abJ
wXYS8VocZJP6Nb4FQMe+cRbBUHoBgBQqbsF60tWiYsjv0zoc5hogLWcZYqzDcIO6
06OBR3HgUW27urUn/JBu
=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----
iQItBAABCAAXBQJaCwaSEBxyb2JoQGtlcm5lbC5vcmcACgkQ+vtdtY28YcNzeA/8
C8uQhSsX2+UQZvFzcEA8KQAMGT3kYdrcf+gidRKwCEUWg1qscUEpTb3n3Rm5NUbU
RPD1s6GSlh6fJCMHDTQ6Tti/T59L7nZa2/AIGmUishGu4x4q1o18AobpFJmYP/EM
SJPwnmm5RV9WcZFao1y+sY3Xtn8DStxHO4cS+dyF5/EvPN9D8nbLJfu7bgTBAZww
HktIMB9kx+GTipRQZBvBwXoy5MJjthIZub4XwzesA4tGananj4cXlc0xaVxpdYy3
5bO6q5F7cbrZ2uyrF+oIChpCENK4VaXh80m0WHc8EzaG++shzEkR4he1vYkwnV+I
OYo4vsUg9dP8rBksUG1eYhS8fJKPvEBRNP7ETT5utVBy5I/tDEbo/crmQZRTIDIC
hZbhcdZlISZj0DzkMK2ZHQV9UYtRWzXrJbZHFIPP12GCyvXVxYJUIWb9iYnUYSon
KugygsFSpZHMWmfAhemw5/ctJZ19qhM5UIl2KZk5tMBHAf466ILmZjg0me6fYkOp
eADfwHJ1dLMdK79CVMHSfp+vArcZXp35B16c3sWpJB36Il97Mc/9siEufCL4GKX7
IBBnQBlbpSBKBejWVyI7Ip/Xp5u4qAQD+ZMJ9oLqBRqfWerHbDuOERlEOgwGqJYr
9v4HvP7V8eVUvAdqXka4EBfCyAgUzXDAxG2Dfmv9vGU=
=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Reintroduction of the EMAC bindings that were reverted in 4.13.
-----BEGIN PGP SIGNATURE-----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=mDKb
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner arm64 changes, take 2" from Maxime Ripard:
Reintroduction of the EMAC bindings that were reverted in 4.13.
* tag 'sunxi-dt64-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: add snps,dwmac-mdio compatible to emac/mdio
arm64: dts: allwinner: A64: Restore EMAC changes
Two long awaited changes:
- Reintroduction of the new EMAC DT bindings that got reverted at the
last minute in 4.13
- Introduction of the AXP803/813 PMIC support
-----BEGIN PGP SIGNATURE-----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=96rw
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15, take 2" from Maxime Ripard:
Here are a few commits that would be great to get in 4.15, given how
long they've been hanging around.
The first and most important one is the reintroduction of the EMAC DT
changes after they've been reverted at the last minute in 4.13.
There's a arm64 patch that crept in because the H5 and H3 share a
common DTSI that is located in arch/arm, and merging that patch
through the arm64 PR, especially given the pull requests that have
already been sent, would just have generated too many conflicts.
* tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
ARM: dts: sunxi: Restore EMAC changes (boards)
ARM: dts: sunxi: h3/h5: represent the mdio switch used by sun8i-h3-emac
arm: dts: sunxi: h3/h5: Restore EMAC changes
dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
dt-bindings: net: Restore sun8i dwmac binding
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for H5
This reverts a part of commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
stmmac bindings docs said that its mdio node must have
compatible = "snps,dwmac-mdio";
Since dwmac-sun8i does not have any good reasons to not doing it, all
their MDIO node must have it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for A64
This reverts commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most notable changes:
- SPI and DMA support on the a64
- New boards: NanoPi NEO Plus2
-----BEGIN PGP SIGNATURE-----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=OAav
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner arm64 DT changes for 4.15" from Maxime Ripard:
Most notable changes:
- SPI and DMA support on the a64
- New boards: NanoPi NEO Plus2
* tag 'sunxi-dt64-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: allwinner: Correct unit name in devicetree binding example
arm64: allwinner: a64: add dma controller references to spi nodes
arm64: allwinner: a64: Add device node for DMA controller
arm64: allwinner: a64: Fix node with unit name and no reg property
arm64: allwinner: a64: Fix simple-bus unit address format error
arm64: allwinner: h5: add NanoPi NEO Plus2 DT support
arm64: allwinner: a64: add SPI nodes
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
-----BEGIN PGP SIGNATURE-----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=HjP6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15" from Maxime Ripard:
The most notable changes are:
- Conversion to the last SoC (A10, A20) to the new clock framework
- HDMI and dual pipeline support for the A10, A20 and A31 DRM driver
- Support for the various power supplies on a number of boards
- Fix of DTC warnings on a number of SoCs, but most of them still need
some work
- New boards: A20-OLinuXino-MICRO-eMMC, TBS A711, Banana Pi M2 Berry,
Banana Pi M2 Ultra
- New R40 SoC support
* tag 'sunxi-dt-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (63 commits)
ARM: sun8i: r40: enable USB host for Banana Pi M2 Ultra
ARM: sun8i: v40: add 5V regulator for Banana Pi M2 Berry
ARM: sun8i: r40: add 5V regulator for Banana Pi M2 Ultra
ARM: sun8i: r40: add USB host port nodes for R40
ARM: dts: sun4i: Enable HDMI support on some A10 devices
ARM: dts: sun7i: Enable HDMI support on some A20 devices
ARM: dts: sun7i: Add device nodes for display pipelines
ARM: dts: sun4i: Add device nodes for display pipelines
ARM: dts: sun8i: r40: add watchdog device node
ARM: dts: sun5i: reference-design-tablet: Enable AXP209 AC and battery
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun9i: Change node names to remove underscores
ARM: dts: sun4i: Remove underscores from nodes names
ARM: dts: sun4i: Provide default muxing for relevant controllers
ARM: dts: sun4i: Change pinctrl nodes to avoid warning
ARM: dts: sun6i: Enable HDMI support on some A31/A31s devices
ARM: dts: sun6i: Add device node for HDMI controller
ARM: dts: sun4i: Change LRADC node names to avoid warnings
ARM: dts: sun4i: Remove skeleton and memory to avoid warnings
ARM: dts: sun4i: Remove gpio-keys warnings
...
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot/dts -type -f -name '*.dts*'
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The spi controller nodes omit the dma controller/channel references, add
it.
This does not yet enable DMA for SPI transfers, as the spi-sun6i driver
lacks support for DMA, but always uses PIO to the FIFO.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A64 SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals. The last used DRQ port is 27.
Add a device node for it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch fix the warning "xxx has a unit name, but no reg property" by
removing "@0" from such node
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A64 SPI controllers are register compatible to the h3/h5 SPI
controllers.
The A64 has two SPI controllers, each with a single chip select.
The handles for the DMA channels (23/24 for SPI0/SPI1) are omitted,
as the A64 DMA support is currently missing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators, replace
fixed regulator with AXP803 dcdc1 regulator.
Tested on pine64.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
-----BEGIN PGP SIGNATURE-----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=u/18
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 device tree changes for 4.14, round 2" from Chen-Yu Tsai:
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
* tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: Add A64-OLinuXino initial support
arm64: allwinner: a64: Add initial NanoPi A64 support
arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64
arm64: allwinner: a64: enable AXP803 for Banana Pi M64
arm64: allwinner: a64: enable USB host controller for BPi M64
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
-----BEGIN PGP SIGNATURE-----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=9oen
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 DT changes for 4.14" from Chen-Yu Tsai:
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
* tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: add AXP803 PMIC support to SoPine and the baseboard
arm64: allwinner: a64: enable AXP803 regulators for Pine64
arm64: allwinner: a64: add DTSI file for AXP803 PMIC
arm64: allwinner: a64: add AXP803 node to Pine64 device tree
arm64: allwinner: a64: add NMI (R_INTC) controller on A64
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pin controller of H5 has three IRQs at the chip's GIC, which
represents three banks of pinctrl IRQs. However, the device tree used to
miss the third IRQ of the pin controller, which makes the PG bank IRQ
not usable.
Add the missing IRQ to the pinctrl node.
Fixes: 4e36de179f ("arm64: allwinner: h5: add Allwinner H5 .dtsi")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.
The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.
Fix these issues for proper Wi-Fi support of BPi M64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 board uses an AXP803 PMIC.
Enable the PMIC and its regulators.
As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.
Enable the USB host controller.
The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Olof Johansson