By Stephen Warren (30) and others
via Stephen Warren
* 'for-3.5/usb-ulpi' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (7 commits)
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
+ depends/pinctrl/mergebase branch
Pinctrl mergebase has a conflict in drivers/pinctrl/core.c that was resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
By Stephen Warren (12) and others
via Linus Walleij
* tag 'pinctrl-mergebase-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (24 commits)
pinctrl: show pin name for pingroups in sysfs
pinctrl: show pin name when request pins
pinctrl: implement devm_pinctrl_get()/put()
pinctrl: a minor fix of pin config debug information
pinctrl: pinconf: fix compilation error if PINCONF is not selected
pinctrl: allow pctldevs to decode pin config in debugfs
pinctrl: ifdef CONFIG_DEBUG_FS cleanup
pinctrl: mark non-EXPERIMENTAL
pinctrl: tegra: Add complete device tree support
dt: Document Tegra20/30 pinctrl binding
dt: Move Tegra20 pin mux binding into new pinctrl directory
dt: pinctrl: Document device tree binding
dt: add property iteration helpers
pinctrl: implement pinctrl deferred probing
pinctrl: add some error checking for user interfaces
pinctrl: fix pinmux_check_ops error checking
pinctrl: replace list_*() with get_*_count()
pinctrl: mark const init data with __initconst instead of __initdata
Documentation: pinctrl: add missing spi0_0 grp in example
pinctrl: fix build when CONFIG_OF && !CONFIG_PINCTRL
...
Resolved conflicts in drivers/pinctrl/core.c due to same patch being
applied in two branches.
Signed-off-by: Olof Johansson <olof@lixom.net>
1. move mei.txt, TODO, and the example code under Documentation/misc-devices/mei
2. update the TODO file
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for National Semiconductor / TI LM3533 lighting power chips.
This is the core driver which provides register access over I2C and
registers the ambient-light-sensor, LED and backlight sub-drivers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into next/cleanup
Linux 3.4-rc6
Resolve conflict where an u5500 file had a bugfix go in, but was
deleted in the branch staged for next merge window.
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij <linus.walleij@linaro.org> writes:
this pull request contains some device tree work by Lee Jones.
I have tried to keep these patches in the arch/arm/boot/dts/*
space to get some sanity in the branch proliferation.
There is still one patch that touches arch/arm/mach-ux500 too
though (but it should merge fine with the other ux500 stuff).
The changes to the device tree are of course dependent on some
core changes and some patching in the GPIO/pin driver, but as
the device tree files are believed to be a different world
(and should one day live in their own git) I split this off
anyway. I don't think people bisect the device trees per se
and the board code in conjunction anyway.
* 'ux500-devicetree-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Configure the PRCMU Timer for db8500 based devices in DT
ARM: ux500: Enable the SMSC9115 on Snowball via Device Tree
drivers/gpio: represent gpio-nomadik as an IRQ controller in DT documentation
ARM: ux500: Rename gpio_keys in the Device Tree file
drivers/gpio: gpio-nomadik: Provide documentation for Device Tree bindings
drivers/gpio: gpio-nomadik: Device Tree bindings
ARM: ux500: Enable the external bus with Device Tree
ARM: ux500: Shorten Snowball's DT compatible gpio entry
ARM: ux500: Rename the DT compatible entry for i2c devices on Snowball
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
Roland Stigge <stigge@antcom.de> writes:
this is a rearrangement of all mach-lpc32xx specific patches for device
tree conversion. Please note that:
* It builds upon the i2c-pnx changes (see previous pull request, branch
lpc32xx/i2c)
* Dave Miller gave permission to merge the lpc_eth.c change via arm-soc
(patch 1/8)
The rest of the patches is mach-lpc32xx only.
* 'lpc32xx/dt' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Defconfig update
ARM: LPC32xx: Move common code to common.c
ARM: LPC32xx: Device tree support
ARM: LPC32xx: DTS files for device tree conversion
ARM: LPC32xx: Remove obsolete platform Kconfig
ARM: LPC32xx: clock.c registration adjustment
ARM: LPC32xx: clock.c cleanup
net: Add device tree support to LPC32xx
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
As a prerequisite for merging the lpc32xx DT changes, this
pulls in the depends/i2c/lpc32xx branch that contains
changes to the pnx-i2c driver, which are already in the
i2c tree. The branch is available also on
git://git.antcom.de/linux-2.6.git lpc32xx/i2c
Roland Stigge <stigge@antcom.de> writes:
this is the series of the 4 patches adding device tree support to i2c-pnx
(used by LPC32xx) that Wolfram Sang already applied to the i2c subsystem.
Since both drivers/i2c/ and mach-lpc32xx are touched here, there will
probably be conflicts that you need to be aware of.
I'm posting this again for arm-soc since the actual mach-lpc32xx specific
DT conversion builds upon those changes (see next pull request), especially
in arch/arm/mach-lpc32xx/common.c.
Wolfram already gave permission to merge this via arm-soc, but please
coordinate and tell me if I can help resolving this.
Further, this implicitly updates the next/dt branch to v3.4-rc4, which
causes a trivial conflict from a change in one branch in code that
gets removed in another.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
The documentation for the VME device driver API is currently in
drivers/vme/vme_api.txt, move this to Documentation/vme_api.txt
Signed-of-by: Martyn Welch <martyn.welch@ge.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra AHB Bus conforms to the AMBA Specification (Rev 2.0) Advanced
High-performance Bus (AHB) architecture.
The AHB Arbiter controls AHB bus master arbitration. This effectively
forms a second level of arbitration for access to the memory
controller through the AHB Slave Memory device. The AHB pre-fetch
logic can be configured to enhance performance for devices doing
sequential access. Each AHB master is assigned to either the high or
low priority bin. Both Tegra20/30 have this AHB bus.
Some of configuration params could be passed from DT too if needed.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.
This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.
Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
if net.bridge.bridge-nf-filter-vlan-tagged sysctl is enabled, bridge
netfilter removes the vlan header temporarily and then feeds the packet
to ip(6)tables.
When the new "bridge-nf-pass-vlan-input-device" sysctl is on
(default off), then bridge netfilter will also set the
in-interface to the vlan interface; if such an interface exists.
This is needed to make iptables REDIRECT target work with
"vlan-on-top-of-bridge" setups and to allow use of "iptables -i" to
match the vlan device name.
Also update Documentation with current brnf default settings.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
PPC updates from Alex.
* 'for-upstream' of git://github.com/agraf/linux-2.6:
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
KVM: PPC: Book3S: PR: No isync in slbie path
KVM: PPC: Book3S: PR: Optimize entry path
KVM: PPC: booke(hv): Fix save/restore of guest accessible SPRGs.
KVM: PPC: Restrict PPC_[L|ST]D macro to asm code
KVM: PPC: bookehv: Use a Macro for saving/restoring guest registers to/from their 64 bit copies.
KVM: PPC: Use clockevent multiplier and shifter for decrementer
KVM: Use minimum and maximum address mapped by TLB1
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit f3f096cfe ("tracing: Provide trace events interface for
uprobes") throws a warning about unmet dependencies.
The exact warning message is:
warning: (UPROBE_EVENT) selects UPROBES which has unmet direct dependencies (UPROBE_EVENTS && PERF_EVENTS)
This is due to a typo in arch/Kconfig file. Fix similar typos in
the uprobetracer documentation.
Also add sample format of a uprobe event in the uprobetracer
documentation as suggested by Masami Hiramatsu.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Anton Arapov <anton@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120508111126.21004.38285.sendpatchset@srdronam.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pins select which sub bus is connected to the master.
Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a somewhat generic framework for MDIO bus
multiplexers. It is modeled on the I2C multiplexer.
The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.
Conceptually it could look something like this:
------------------
| Control Signal |
--------+---------
|
--------------- --------+------
| MDIO MASTER |---| Multiplexer |
--------------- --+-------+----
| |
C C
h h
i i
l l
d d
| |
--------- A B ---------
| | | | | |
| PHY@1 +-------+ +---+ PHY@1 |
| | | | | |
--------- | | ---------
--------- | | ---------
| | | | | |
| PHY@2 +-------+ +---+ PHY@2 |
| | | |
--------- ---------
This framework configures the bus topology from device tree data. The
mechanics of switching the multiplexer is left to device specific
drivers.
The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch for correcting a mistake sentence in the file
Documentation/zh_CN/magic-number.txt.
signed-off-by: Harry Wei <harryxiyou@gmail.com>
Reported-by: Zhang Shuanglong <zhangsl16@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like with ctrl events, drivers may want to get called back on
listener add / remove for other event types too. Rather then special
casing all of this in subscribe / unsubscribe event it is better to
use ops for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implements trace_event support for uprobes. In its current form
it can be used to put probes at a specified offset in a file and
dump the required registers when the code flow reaches the
probed address.
The following example shows how to dump the instruction pointer
and %ax a register at the probed text address. Here we are
trying to probe zfree in /bin/zsh:
# cd /sys/kernel/debug/tracing/
# cat /proc/`pgrep zsh`/maps | grep /bin/zsh | grep r-xp
00400000-0048a000 r-xp 00000000 08:03 130904 /bin/zsh
# objdump -T /bin/zsh | grep -w zfree
0000000000446420 g DF .text 0000000000000012 Base
zfree # echo 'p /bin/zsh:0x46420 %ip %ax' > uprobe_events
# cat uprobe_events
p:uprobes/p_zsh_0x46420 /bin/zsh:0x0000000000046420
# echo 1 > events/uprobes/enable
# sleep 20
# echo 0 > events/uprobes/enable
# cat trace
# tracer: nop
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |
zsh-24842 [006] 258544.995456: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79
zsh-24842 [007] 258545.000270: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79
zsh-24842 [002] 258545.043929: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79
zsh-24842 [004] 258547.046129: p_zsh_0x46420: (0x446420) arg1=446421 arg2=79
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Anton Arapov <anton@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120411103043.GB29437@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into drm-intel-next
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add property for the gpio flag open drain when registering
fixed regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is necessary for qemu to be able to pass the right information
to the guest, such as the supported page sizes and corresponding
encodings in the SLB and hash table, which can vary depending
on the processor type, the type of KVM used (PR vs HV) and the
version of KVM
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[agraf: fix compilation on hv, adjust for newer ioctl numbers]
Signed-off-by: Alexander Graf <agraf@suse.de>
cpuid eax should return the max leaf so that
guests can find out the valid range.
This matches Xen et al.
Update documentation to match.
Tested with -cpu host.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
After we moved inode_sync_wait() from end_writeback() it doesn't make sense
to call the function end_writeback() anymore. Rename it to clear_inode()
which well says what the function really does - set I_CLEAR flag.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
By using cm_notify_event function, charger driver can report several
charger events (e.g. battery full and external power in/out, etc) to
Charger-Manager. Charger-Manager can properly and immediately control
chargers by the reported event.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Charger-Manager needs to check battery health in normal state
as well as suspend-to-RAM state. When the battery is fully charged,
Charger-Manager needs to determine when the chargers restart charging.
This patch allows Charger-Manager to monitor battery health in normal
state and handle operation for chargers after battery is fully charged.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
sysfs was expected in this context.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
As good as nothing exciting here; just a few trivial fixes for
various ASoC stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ZPkR
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound sound fixes from Takashi Iwai:
"As good as nothing exciting here; just a few trivial fixes for various
ASoC stuff."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: omap-pcm: Free dma buffers in case of error.
ASoC: s3c2412-i2s: Fix dai registration
ASoC: wm8350: Don't use locally allocated codec struct
ASoC: tlv312aic23: unbreak resume
ASoC: bf5xx-ssm2602: Set DAI format
ASoC: core: check of_property_count_strings failure
ASoC: dt: sgtl5000.txt: Add description for 'reg' field
ASoC: wm_hubs: Make sure we don't disable differential line outputs
Add the PCI ID of the Asus Xonar DGX card; it's otherwise
identical with the DG.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nothing terribly exciting here, a bunch of small and simple fixes
scattered around the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Z1L5
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for 3.4
Nothing terribly exciting here, a bunch of small and simple fixes
scattered around the place.
This adds a new sysfs file called 'voltage_ocv' which gives the
Open Circuit Voltage of the battery.
This property can be used for platform shutdown policies and
can be useful for initial capacity estimations.
Note: This patch is generated against linux-next branch.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
- Only try to read the file specified if KCONFIG_ALL_CONFIG is set to
something other than the empty string or "1".
- Don't use stat to check the name passed to conf_read_simple so that
zconf_fopen can find the file in the current directory or in SRCTREE
removing a extremely source of confusing failure, where KCONFIG_ALL_CONFIG
was not interpreted with respect to the directory make was called in.
- If conf_read_simple fails complain clearly and stop processing.
Allowing the simple debugging of typos.
- Clearly document the behavior so it is clear to users which
values are treated as flags and which values are treated as
filenames.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This provides full documentation detailing each compulsory,
optional and device (variant) specific properties available
for use within the MMCI Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arndb@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This commit adds device tree support for the TPS6586x regulator.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPnb50AAoJEHm+PkMAQRiGAE0H/A4zFZIUGmF3miKPDYmejmrZ
oVDYxVAu6JHjHWhu8E3VsinvyVscowjV8dr15eSaQzmDmRkSHAnUQ+dB7Di7jLC2
MNopxsWjwyZ8zvvr3rFR76kjbWKk/1GYytnf7GPZLbJQzd51om2V/TY/6qkwiDSX
U8Tt7ihSgHAezefqEmWp2X/1pxDCEt+VFyn9vWpkhgdfM1iuzF39MbxSZAgqDQ/9
JJrBHFXhArqJguhENwL7OdDzkYqkdzlGtS0xgeY7qio2CzSXxZXK4svT6FFGA8Za
xlAaIvzslDniv3vR2ZKd6wzUwFHuynX222hNim3QMaYdXm012M+Nn1ufKYGFxI0=
=4d4w
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc5' into next
Linux 3.4-rc5
Merge to pull in prerequisite change for Smack:
86812bb0de
Requested by Casey.
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c7fz
-----END PGP SIGNATURE-----
Merge tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
* tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: ahci_platform: Add synopsys ahci controller in DT's compatible list
ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros
libata: init ata_print_id to 0
ahci: Detect Marvell 88SE9172 SATA controller
libata: skip old error history when counting probe trials
Pull networking fixes from David Miller:
1) Transfer padding was wrong for full-speed USB in ASIX driver, fix
from Ingo van Lil.
2) Propagate the negative packet offset fix into the PowerPC BPF JIT.
From Jan Seiffert.
3) dl2k driver's private ioctls were letting unprivileged tasks make
MII writes and other ugly bits like that. Fix from Jeff Mahoney.
4) Fix TX VLAN and RX packet drops in ucc_geth, from Joakim Tjernlund.
5) OOPS and network namespace fixes in IPVS from Hans Schillstrom and
Julian Anastasov.
6) Fix races and sleeping in locked context bugs in drop_monitor, from
Neil Horman.
7) Fix link status indication in smsc95xx driver, from Paolo Pisati.
8) Fix bridge netfilter OOPS, from Peter Huang.
9) L2TP sendmsg can return on error conditions with the socket lock
held, oops. Fix from Sasha Levin.
10) udp_diag should return meaningful values for socket memory usage,
from Shan Wei.
11) Eric Dumazet is so awesome he gets his own section:
Socket memory cgroup code (I never should have applied those
patches, grumble...) made erroneous changes to
sk_sockets_allocated_read_positive(). It was changed to
use percpu_counter_sum_positive (which requires BH disabling)
instead of percpu_counter_read_positive (which does not).
Revert back to avoid crashes and lockdep warnings.
Adjust the default tcp_adv_win_scale and tcp_rmem[2] values
to fix throughput regressions. This is necessary as a result
of our more precise skb->truesize tracking.
Fix SKB leak in netem packet scheduler.
12) New device IDs for various bluetooth devices, from Manoj Iyer,
AceLan Kao, and Steven Harms.
13) Fix command completion race in ipw2200, from Stanislav Yakovlev.
14) Fix rtlwifi oops on unload, from Larry Finger.
15) Fix hard_mtu when adjusting hard_header_len in smsc95xx driver.
From Stephane Fillod.
16) ehea driver registers it's IRQ before all the necessary state is
setup, resulting in crashes. Fix from Thadeu Lima de Souza
Cascardo.
17) Fix PHY connection failures in davinci_emac driver, from Anatolij
Gustschin.
18) Missing break; in switch statement in bluetooth's
hci_cmd_complete_evt(). Fix from Szymon Janc.
19) Fix queue programming in iwlwifi, from Johannes Berg.
20) Interrupt throttling defaults not being actually programmed into the
hardware, fix from Jeff Kirsher and Ying Cai.
21) TLAN driver SKB encoding in descriptor busted on 64-bit, fix from
Benjamin Poirier.
22) Fix blind status block RX producer pointer deref in TG3 driver, from
Matt Carlson.
23) Promisc and multicast are busted on ehea, fixes from Thadeu Lima de
Souza Cascardo.
24) Fix crashes in 6lowpan, from Alexander Smirnov.
25) tcp_complete_cwr() needs to be careful to not rewind the CWND to
ssthresh if ssthresh has the "infinite" value. Fix from Yuchung
Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
sungem: Fix WakeOnLan
tcp: change tcp_adv_win_scale and tcp_rmem[2]
net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg
drop_monitor: prevent init path from scheduling on the wrong cpu
usbnet: fix failure handling in usbnet_probe
usbnet: fix leak of transfer buffer of dev->interrupt
ucc_geth: Add 16 bytes to max TX frame for VLANs
net: ucc_geth, increase no. of HW RX descriptors
netem: fix possible skb leak
sky2: fix receive length error in mixed non-VLAN/VLAN traffic
sky2: propogate rx hash when packet is copied
net: fix two typos in skbuff.h
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
ixgbe: fix calling skb_put on nonlinear skb assertion bug
ixgbe: Fix a memory leak in IEEE DCB
igbvf: fix the bug when initializing the igbvf
smsc75xx: enable mac to detect speed/duplex from phy
smsc75xx: declare smsc75xx's MII as GMII capable
smsc75xx: fix phy interrupt acknowledge
smsc75xx: fix phy init reset loop
...
SPEAr13xx series of SoCs contain Synopsys AHCI SATA Controller which shares
ahci_platform driver with other controller versions.
This patch updates DT compatible list for ahci_platform. It also updates and
renames binding documentation to more generic name.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
tcp_adv_win_scale default value is 2, meaning we expect a good citizen
skb to have skb->len / skb->truesize ratio of 75% (3/4)
In 2.6 kernels we (mis)accounted for typical MSS=1460 frame :
1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392.
So these skbs were considered as not bloated.
With recent truesize fixes, a typical MSS=1460 frame truesize is now the
more precise :
2048 + 256 = 2304. But 2304 * 3/4 = 1728.
So these skb are not good citizen anymore, because 1460 < 1728
(GRO can escape this problem because it build skbs with a too low
truesize.)
This also means tcp advertises a too optimistic window for a given
allocated rcvspace : When receiving frames, sk_rmem_alloc can hit
sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often,
especially when application is slow to drain its receive queue or in
case of losses (netperf is fast, scp is slow). This is a major latency
source.
We should adjust the len/truesize ratio to 50% instead of 75%
This patch :
1) changes tcp_adv_win_scale default to 1 instead of 2
2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account
better truesize tracking and to allow autotuning tcp receive window to
reach same value than before. Note that same amount of kernel memory is
consumed compared to 2.6 kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements RFC 5827 early retransmit (ER) for TCP.
It reduces DUPACK threshold (dupthresh) if outstanding packets are
less than 4 to recover losses by fast recovery instead of timeout.
While the algorithm is simple, small but frequent network reordering
makes this feature dangerous: the connection repeatedly enter
false recovery and degrade performance. Therefore we implement
a mitigation suggested in the appendix of the RFC that delays
entering fast recovery by a small interval, i.e., RTT/4. Currently
ER is conservative and is disabled for the rest of the connection
after the first reordering event. A large scale web server
experiment on the performance impact of ER is summarized in
section 6 of the paper "Proportional Rate Reduction for TCP”,
IMC 2011. http://conferences.sigcomm.org/imc/2011/docs/p155.pdf
Note that Linux has a similar feature called THIN_DUPACK. The
differences are THIN_DUPACK do not mitigate reorderings and is only
used after slow start. Currently ER is disabled if THIN_DUPACK is
enabled. I would be happy to merge THIN_DUPACK feature with ER if
people think it's a good idea.
ER is enabled by sysctl_tcp_early_retrans:
0: Disables ER
1: Reduce dupthresh to packets_out - 1 when outstanding packets < 4.
2: (Default) reduce dupthresh like mode 1. In addition, delay
entering fast recovery by RTT/4.
Note: mode 2 is implemented in the third part of this patch series.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was done to resolve a merge issue with the init/main.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7B/b
-----END PGP SIGNATURE-----
Merge tag 'imx-cleanup' of git://git.pengutronix.de/git/imx/linux-2.6 into next/cleanup
From: Sascha Hauer <s.hauer@pengutronix.de>
ARM: i.MX cleanups for 3.5
* tag 'imx-cleanup' of git://git.pengutronix.de/git/imx/linux-2.6: (5 commits)
ARM: mx53: fix pad definitions for MX53_PAD_EIM_D28__I2C1_SDA and MX53_PAD_GPIO_8__CAN1_RXCAN
ARM: imx/eukrea_mbimx27-baseboard: fix typo in error message
ARM: i.MX51 iomux: add missed definitions for SION-bit and mode for some pads
arm: imx: add missing select IMX_HAVE_PLATFORM for MACH_MX35_3DS in Kconfig
arm: imx: make various struct sys_timer static
Includes an update to 3.4-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
EMIF is an SDRAM controller used in various Texas Instruments
SoCs. EMIF supports, based on its revision, one or more of
LPDDR2/DDR2/DDR3 protocols.
Add the basic infrastructure for EMIF driver that includes
driver registration, probe, parsing of platform data etc.
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pinctrl support for Freescale MXS SoCs, i.MX23 and i.MX28.
The driver supports device tree probe only.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver has mux and config support while the gpio is still
not supported.
For select input setting, the driver will handle it internally
and do not need user to take care of it.
The pinctrl-imx core driver will parse the dts file and dynamically
create the pinmux functions and groups.
Each IMX SoC pinctrl driver should register pins with a pin register map
including mux register and config register and select input map to core
for proper operations.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Android allows user space to manipulate wakelocks using two
sysfs file located in /sys/power/, wake_lock and wake_unlock.
Writing a wakelock name and optionally a timeout to the wake_lock
file causes the wakelock whose name was written to be acquired (it
is created before is necessary), optionally with the given timeout.
Writing the name of a wakelock to wake_unlock causes that wakelock
to be released.
Implement an analogous interface for user space using wakeup sources.
Add the /sys/power/wake_lock and /sys/power/wake_unlock files
allowing user space to create, activate and deactivate wakeup
sources, such that writing a name and optionally a timeout to
wake_lock causes the wakeup source of that name to be activated,
optionally with the given timeout. If that wakeup source doesn't
exist, it will be created and then activated. Writing a name to
wake_unlock causes the wakeup source of that name, if there is one,
to be deactivated. Wakeup sources created with the help of
wake_lock that haven't been used for more than 5 minutes are garbage
collected and destroyed. Moreover, there can be only WL_NUMBER_LIMIT
wakeup sources created with the help of wake_lock present at a time.
The data type used to track wakeup sources created by user space is
called "struct wakelock" to indicate the origins of this feature.
This version of the patch includes an rbtree manipulation fix from John Stultz.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NeilBrown <neilb@suse.de>
Android uses one wakelock statistics that is only necessary for
opportunistic sleep. Namely, the prevent_suspend_time field
accumulates the total time the given wakelock has been locked
while "automatic suspend" was enabled. Add an analogous field,
prevent_sleep_time, to wakeup sources and make it behave in a similar
way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a mechanism by which the kernel can trigger global
transitions to a sleep state chosen by user space if there are no
active wakeup sources.
It consists of a new sysfs attribute, /sys/power/autosleep, that
can be written one of the strings returned by reads from
/sys/power/state, an ordered workqueue and a work item carrying out
the "suspend" operations. If a string representing the system's
sleep state is written to /sys/power/autosleep, the work item
triggering transitions to that state is queued up and it requeues
itself after every execution until user space writes "off" to
/sys/power/autosleep.
That work item enables the detection of wakeup events using the
functions already defined in drivers/base/power/wakeup.c (with one
small modification) and calls either pm_suspend(), or hibernate() to
put the system into a sleep state. If a wakeup event is reported
while the transition is in progress, it will abort the transition and
the "system suspend" work item will be queued up again.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NeilBrown <neilb@suse.de>
Wakeup statistics used by Android are slightly different from what we
have in wakeup sources at the moment and there aren't any known
users of those statistics other than Android, so modify them to make
it easier for Android to switch to wakeup sources.
This removes the struct wakeup_source's hit_cout field, which is very
rough and therefore not very useful, and adds two new fields,
wakeup_count and expire_count. The first one tracks how many times
the wakeup source is activated with events_check_enabled set (which
roughly corresponds to the situations when a system power transition
to a sleep state is in progress and would be aborted by this wakeup
source if it were the only active one at that time) and the second
one is the number of times the wakeup source has been activated with
a timeout that expired.
Additionally, the last_time field is now updated when the wakeup
source is deactivated too (previously it was only updated during
the wakeup source's activation), which seems to be what Android does
with the analogous counter for wakelocks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ohci-nxp duplicates the isp1301 driver. This patch removes this code and makes
ohci-nxp use the new separate isp1301 driver instead.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a USB gadget driver for the LPC32xx ARM SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new driver registers the NXP ISP1301 chip via the I2C subsystem. The chip
is the USB transceiver shared by ohci-nxp, lpc32xx_udc (gadget) and
isp1301_omap.
ISP1301 is a very low-level driver that primarily separates out the I2C client
registration of the ISP1301 chip (including instantiation via DT), used by
other drivers, and declares the chip's registers. It's only a helper driver for
some OHCI and USB device drivers. The driver can be considered as a register
set extension of ohci-nxp, lpc32xx-udc and isp1301_omap, which in turn know
best what to do with the low level functionality (individual ISP1301 registers
and timing, see the different initialization strategies in those drivers).
Those drivers previously internally duplicated ISP1301 register definitions
which is solved by this new isp1301 driver. The ISP1301 registers exposed via
isp1301.h can be accessed by other drivers using it with standard i2c_smbus_*()
accesses.
Following patches let the respective USB host and gadget drivers use this
driver, instead of duplicating ISP1301 handling.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds device tree support to ohci-nxp.c
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds device-tree support for dialog MFD and the binding
documentations.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This binding doesn't include the nvidia,model or nvidia,audio-routing
properties the other Tegra audio DT bindings have, because this binding
is targetted at a single machine, rather than for any machine using the
tlv320aic23 codec.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Walleij <linus.walleij@linaro.org> writes:
This is a pull request for the GPIO and pin control stuff
accumulated in the ST-Ericsson tree. Here we have:
- Improvements and fixes and a custom pin config API from
Rabin Vincent
- Device Tree bindings from Lee Jones
- Some accumulated patches by yours truly.
- A MSP platform data init patch from Ola Lilja that is merged
here due to dependency on pin config work. It is to be
used with work being worked on in parallel in the ALSA
SoC subsystem.
If you wonder about the custom pin config implementation this
is to be used as a transition base as I am rewriting the
driver to use pinctrl. Expect a final pull request on top
of this one that will move the ux500 over to pinctrl.
* 'ux500-gpio-pins-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Add support for MSP I2S-devices
drivers/gpio: gpio-nomadik: Add support for irqdomains
drivers/gpio: gpio-nomadik: Apply Device Tree bindings
ARM: ux500: update pin handling
ARM: ux500: implement pin API
ARM: ux500: remove a bunch of internal pull-ups
plat-nomadik: new sleep mode pincfg macros
gpio/nomadik: use ioremap() instead of static mappings
gpio/nomadik: support low EMI mode
gpio/nomadik: fix spurious interrupts with SKE
gpio/nomadik: cache [rf]w?imsc
gpio/nomadik: don't set SLPM to 1 for non-wakeup pins
Also includes an update to v3.4-rc4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A PCIe downstream port is a P2P bridge. Its secondary interface is
a link that should lead only to device 0 (unless ARI is enabled)[1], so
we don't probe for non-zero device numbers.
Some Stratus ftServer systems have a PCIe downstream port (02:00.0) that
leads to both an upstream port (03:00.0) and a downstream port (03:01.0),
and 03:01.0 has important devices below it:
[0000:02]-+-00.0-[03-3c]--+-00.0-[04-09]--...
\-01.0-[0a-0d]--+-[USB]
+-[NIC]
+-...
Previously, we didn't enumerate device 03:01.0, so USB and the network
didn't work. This patch adds a DMI quirk to scan all device numbers,
not just 0, below a downstream port.
Based on a patch by Prarit Bhargava.
[1] PCIe spec r3.0, sec 7.3.1
CC: Myron Stowe <mstowe@redhat.com>
CC: Don Dutile <ddutile@redhat.com>
CC: James Paradis <james.paradis@stratus.com>
CC: Matthew Wilcox <matthew.r.wilcox@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In dynamic-debug-howto.txt:
- add section: Debug Messages at Module Initialization Time
- update flags indicators in example outputs to include '='
- make flags descriptions tabular
- add item on '_' flag-char
- add dyndbg, boot-args examples
- rewrap some paragraphs with long lines
In Kconfig.debug, note that compiling with -DDEBUG enables all
pr_debug()s in that code.
In kernel-parameters.txt, add dyndbg and module.dyndbg items,
and deprecate ddebug_query.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ddebug_dyndbg_boot_params_cb() handling bare dyndbg params, we
dont need ddebug_query param anymore. Add a warning when processing
ddebug_query= param that it is deprecated, and to change it to dyndbg=
Add a deprecation notice for v3.8 to feature-removal-schedule.txt, and
add a suggested deprecation period of 3 releases to the header.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although rcutorture does invoke rcu_barrier() and friends, it cannot
really be called a torture test given that it invokes them only once
at the end of the test. This commit therefore introduces heavy-duty
rcutorture testing for rcu_barrier(), which may be carried out
concurrently with normal rcutorture testing.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Fix for an issue causing hibernation to hang on systems with highmem (that
practically means i386) due to broken memory management (bug introduced in 3.2,
so -stable material) and PM documentation update making the freezer
documentation follow the code again after some recent updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=HaVL
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Fix for an issue causing hibernation to hang on systems with highmem
(that practically means i386) due to broken memory management (bug
introduced in 3.2, so -stable material) and PM documentation update
making the freezer documentation follow the code again after some
recent updates."
* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer / Docs: Update documentation about freezing of tasks
PM / Hibernate: fix the number of pages used for hibernate/thaw buffering
The file Documentation/power/freezing-of-tasks.txt was still referencing
the TIF_FREEZE flag, that was removed by the commit
d88e4cb67197d007fb778d62fe17360e970d5bfa(freezer: remove now unused
TIF_FREEZE).
This patch removes all the references of TIF_FREEZE that were left
behind.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
We can't run PIT IRQ injection work in the interrupt context of the host
timer. This would allow the user to influence the handler complexity by
asking for a broadcast to a large number of VCPUs. Therefore, this work
was pushed into workqueue context in 9d244caf2e. However, this prevents
prioritizing the PIT injection over other task as workqueues share
kernel threads.
This replaces the workqueue with a kthread worker and gives that thread
a name in the format "kvm-pit/<owner-process-pid>". That allows to
identify and adjust the kthread priority according to the VM process
parameters.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add descriptions for KVM_CREATE_PIT2 and KVM_GET/SET_PIT2.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This helps to identify sections and it also fixes the numbering from
4.54 to 4.61.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
These two functions do almost the same thing and duplicate some code.
Merge their implementation into a single common function.
res_counter_charge_locked() takes one more parameter but it doesn't seem
to be used outside res_counter.c yet anyway.
There is no (intended) change in the behaviour.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Glauber Costa <glommer@parallels.com>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Li Zefan <lizefan@huawei.com>
Add runtime DT support and documentation for the Cortex A7/A15
architected timers.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
All parameter descriptions in /proc/sys/net/core/* now is separated
two places. So, merge them into Documentation/sysctl/net.txt.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These controls have been marked for long time as V4L2_CID_HCENTER_DEPRECATED,
V4L2_CID_VCENTER_DEPRECATED in the DocBook and are going to be removed
from include/linux/videodev2.h.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.
I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.
Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This file contains only the most generic elements. Other
class specific and device specific ABI documents will follow
over time.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bring RCU's kernel command-line parameter documentation up to date.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This patch adds device tree support to the LPC32xx's ADC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, MSI messages can only be injected to in-kernel irqchips by
defining a corresponding IRQ route for each message. This is not only
unhandy if the MSI messages are generated "on the fly" by user space,
IRQ routes are a limited resource that user space has to manage
carefully.
By providing a direct injection path, we can both avoid using up limited
resources and simplify the necessary steps for user land.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add description for 'reg' field.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now gpio-nomadik has proper bindings devices initialised by Device Tree
entries are able to use the chained GPIO IRQ lines it provides. This
patch aims to reflect that in the gpio-nmk documentation.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During the device tree integration of the various LPC32xx drivers,
we agreed on using non-wildcard "compatible" strings. This change
switches lpc32xx_ts touchscreen driver to use "nxp,lpc3220-tsc".
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch for megaraid_sas updates the driver version to
v00.00.06.15-rc1, and updates Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add required documentation for specific gpio-nomadik DT bindings.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds pinctrl driver for SPEAr3xx family. SPEAr3xx family supports three
families: SPEAr300, SPEAr310 and SPEAr320.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
This patch adds a generic target for SPEAr3xx machines that can be configured
via the device-tree. Currently the following devices are supported via the
devicetree:
- VIC interrupts
- PL011 UART
- PL061 GPIO
- PL110 CLCD
- SP805 WDT
- Synopsys DW I2C
- Synopsys DW ethernet
- ST FSMC-NAND
- ST SPEAR-SMI
- ST SPEAR-KEYBOARD
- ST SPEAR-RTC
- ARASAN SDHCI-SPEAR
- SPEAR-EHCI
- SPEAR-OHCI
Other peripheral devices will follow in later patches.
This also removes IO_ADDRESS macro and creates 16 MB static mappings instead of
4K for individual peripherals. This is done to have efficient TLB lookup for any
I/O windows that are located closely together. ioremap() on this range will
return this mapping only instead of creating another.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPjYz4AAoJEAf03oE53VmQ/0wH/3kXJYM/8nX8fqlQ8eTh0SHi
lRsoNL+4arHFKcocYhZyiXEidUKCUMLuQSdvL9MWy1e286+ABsaFgrjfLsp/ZDqE
jDJBCZIxUD6rL94VRnYEHrhWqGzzPKi8/syVZ8JOv/1HGml402CqPcRDKmWY/e4Q
ajl/d463q0ufwfQ4LMP+DsR29TxEdecs4DkxnhwcrRCbJ2hDPLmWVER+tPITPwqp
R8qVGY3K6axG68b964B/hsACjRF7C1lqRQsiQbi8pVPPGEhekmgnW8hF6dNdy1VW
wVo8F0GCST6jLk9YFbirBdKsDRJTLc+WsyP6jUZyWkrrM6p4ycs+voGFDNZbhPw=
=CXyd
-----END PGP SIGNATURE-----
Merge tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
Nicolas Ferre <nicolas.ferre@atmel.com> writes:
First batch of AT91 cleanup for 3.5 kernel.
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
* tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91: (19 commits)
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
ARM: at91: drop at91_set_serial_console
ARM: at91: uncompress: autodetect the uart to use
ARM: at91: uncompress Store UART address in a variable
hwrng: Kconfig: remove dependency for atmel-rng driver
Input: Kconfig: remove dependency for atmel_tsadcc driver
rtc: Kconfig: remove dependency for AT91 rtc driver
ARM: at91/Kconfig: website link for AT91SAM9G20-EK
ARM: at91/Kconfig: add AT91SAM9x5 family to AT91_EARLY_DBGU0 entry
ARM: at91/Kconfig: add clarifications to AT91SAM9M10G45-EK entry
ARM: at91/Kconfig: add comment to at91sam9x5 family entry
ARM: at91/Kconfig: change at91sam9g45 entry
ARM: at91: change AT91 Kconfig entry comment
Also updates the cleanup branch to v3.4-rc3.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds device tree support for lpc_eth.c.
The runtime option for MII/RMII is solved via the "phy-mode" property, SRAM
("IRAM") usage for DMA can be chosen via "use-iram".
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
This patch adds device tree support to the pnx-i2c driver by using platform
resources for memory region and irq and removing dependency on mach includes.
The following platforms are affected:
* PNX
* LPC31xx (WIP)
* LPC32xx
The patch is based on a patch by Jon Smirl, working on lpc31xx integration
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
This change implements device tree support for the LPC32xx SoC's touchscreen
controller.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There could be cables that t recannot be attaches simulatenously. Extcon
device drivers may express such information via mutually_exclusive in
struct extcon_dev.
For example, for an extcon device with 16 cables (bits 0 to 15 are
available), if mutually_exclusive = { 0x7, 0xC0, 0x81, 0 }, then, the
following attachments are prohibitted.
{0, 1}
{0, 2}
{1, 2}
{6, 7}
{0, 7}
and every attachment set that are superset of one of the above.
For the detail, please refer to linux/include/linux/extcon.h.
The concept is suggested by NeilBrown <neilb@suse.de>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
--
Changes from V5:
- Updated sysfs format
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One switch device (e.g., MUIC(MAX8997, MAX77686, ...), and some 30-pin
devices) may have multiple cables attached. For example, one
30-pin port may inhabit a USB cable, an HDMI cable, and a mic.
Thus, one switch device requires multiple state bits each representing
a type of cable.
For such purpose, we use the 32bit state variable; thus, up to 32
different type of cables may be defined for a switch device. The list of
possible cables is defined by the array of cable names in the switch_dev
struct given to the class.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
--
Changes from V7
- Bugfixed in _call_per_cable() (incorrect nb) (Chanwoo Choi)
- Compiler error in header for !CONFIG_EXTCON (Chanwoo Choi)
Changes from V5
- Sysfs style reformed: subdirectory per cable.
- Updated standard cable names
- Removed unnecessary printf
- Bugfixes after testing
Changes from V4
- Bugfixes after more testing at Exynos4412 boards with userspace
processses.
Changes from V3
- Bugfixes after more testing at Exynos4412 boards.
Changes from V2
- State can be stored by user
- Documentation updated
Changes from RFC
- Switch is renamed to extcon
- Added kerneldoc comments
- Added APIs to support "standard" cable names
- Added helper APIs to support notifier block registration with cable
name.
- Regrouped function list in the header file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
External connector class (extcon) is based on and an extension of
Android kernel's switch class located at linux/drivers/switch/.
This patch provides the before-extension switch class moved to the
location where the extcon will be located (linux/drivers/extcon/) and
updates to handle class properly.
The before-extension class, switch class of Android kernel, commits
imported are:
switch: switch class and GPIO drivers. (splitted)
Author: Mike Lockwood <lockwood@android.com>
switch: Use device_create instead of device_create_drvdata.
Author: Arve Hjønnevåg <arve@android.com>
In this patch, upon the commits of Android kernel, we have added:
- Relocated and renamed for extcon.
- Comments, module name, and author information are updated
- Code clean for successing patches
- Bugfix: enabling write access without write functions
- Class/device/sysfs create/remove handling
- Added comments about uevents
- Format changes for extcon_dev_register() to have a parent dev.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Changes from v7
- Compiler error fixed when it is compiled as a module.
- Removed out-of-date Kconfig entry
Changes from v6
- Updated comment/strings
- Revised "Android-compatible" mode.
* Automatically activated if CONFIG_ANDROID && !CONFIG_ANDROID_SWITCH
* Creates /sys/class/switch/*, which is a copy of /sys/class/extcon/*
Changes from v5
- Split the patch
- Style fixes
- "Android-compatible" mode is enabled by Kconfig option.
Changes from v2
- Updated name_show
- Sysfs entries are handled by class itself.
- Updated the method to add/remove devices for the class
- Comments on uevent send
- Able to become a module
- Compatible with Android platform
Changes from RFC
- Renamed to extcon (external connector) from multistate switch
- Added a seperated directory (drivers/extcon)
- Added kerneldoc comments
- Removed unused variables from extcon_gpio.c
- Added ABI Documentation.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HOWTO document needed updating for the new kernel versioning. The
git URI for -next was updated as well.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both radio-keene and dsbr100 did one v4l2_device_get too many. Thus the refcount
never became 0 and that causes a memory leak.
Also updated the V4L2 framework documentation accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
Documentation/feature-removal-schedule.txt
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Allow clk API users to simplify their cleanup paths by providing a
managed version of clk_get() and clk_put().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* tag 'v3.4-rc3': (3755 commits)
Linux 3.4-rc3
x86-32: fix up strncpy_from_user() sign error
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
PCI: Fix regression in pci_restore_state(), v3
SCSI: Fix error handling when no ULD is attached
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
do not export kernel's NULL #define to userspace
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
cpufreq: OMAP: fix build errors: depends on ARCH_OMAP2PLUS
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
ARM: msm: Fix section mismatches in proc_comm.c
...
This expands the available Yama ptrace restrictions to include two more
modes. Mode 2 requires CAP_SYS_PTRACE for PTRACE_ATTACH, and mode 3
completely disables PTRACE_ATTACH (and locks the sysctl).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
This patch adds support to configure the SPEAr EHCI & OHCI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions allow the driver core to automatically clean up any
allocations made by drivers, thus leading to simplified drivers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Define a new binding for the Tegra pin controller, which is capable of
defining all aspects of desired pin multiplexing and pin configuration.
This is all based on the new common pinctrl bindings.
Add Tegra30 binding based on Tegra20 binding.
Add some basic stuff that was missing before:
* How many and what reg property entries must be provided.
* An example.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This places the file in the new location for all pin controller bindings.
Also, rename the file using the full compatible value for easier
avoidance of conflicts between multiple bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core pin controller bindings define:
* The fact that pin controllers expose pin configurations as nodes in
device tree.
* That the bindings for those pin configuration nodes is defined by the
individual pin controller drivers.
* A standardized set of properties for client devices to define numbered
or named pin configuration states, each referring to some number of the
afore-mentioned pin configuration nodes.
* That the bindings for the client devices determines the set of numbered
or named states that must exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If drivers try to obtain pinctrl handles for a pin controller that
has not yet registered to the subsystem, we need to be able to
back out and retry with deferred probing. So let's return
-EPROBE_DEFER whenever this location fails. Also downgrade the
errors to info, maybe we will even set them to debug once the
deferred probing is commonplace.
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most of the SoC drivers implement list_groups() and list_functions()
routines for pinctrl and pinmux. These routines continue returning
zero until the selector argument is greater than total count of
available groups or functions.
This patch replaces these list_*() routines with get_*_count()
routines, which returns the number of available selection for SoC
driver. pinctrl layer will use this value to check the range it can
choose.
This patch fixes all user drivers for this change. There are other
routines in user drivers, which have checks to check validity of
selector passed to them. It is also no more required and hence
removed.
Documentation updated as well.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
[Folded in fix and fixed a minor merge artifact manually]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Missed one group from the documentation when proofreading.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEbBAABAgAGBQJPi3XOAAoJEHm+PkMAQRiGnsUH9RjHwH4YFVyuP/DKtKa6zs74
wqkpT15yITQ5WWMog4JaJFFg5rJCUd8QZr7AS/HSn0ijDyZX5VU7Rcs9cMudDzNR
H/5K/AscS4fjb0HwWVqoltTWHRb9QGSwVN3+E3VCDLt9P89YJ0o3QztkkuEX5dkZ
jc7reVXTfRnCcILEa9jleOzrn+OLM3j/jAjQ2hGunl8EDLzD4b17HHPoli4jEZ/5
5ibpSVsPD+AqzN+glbXvYjVItl12D0IQos/JdOwfuZriCVWLxysSSwHZTbPCyvBZ
LHH4HR5T+XLSXbjJeNkUFHLzqU+d5gVRadIoWtJCxqxFjKbOs2YtzJ5Ai0nDiw==
=kTkC
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc3' into drm-intel-next-queued
Backmerge Linux 3.4-rc3 into drm-intel-next to resolve a few things
that conflict/depend upon patches in -rc3:
- Second part of the Sandybridge workaround series - it changes some
of the same registers.
- Preparation for Chris Wilson's fencing cleanup - we need the fix
from -rc3 merged before we can move around all that code.
- Resolve the gmbus conflict - gmbus has been disabled in 3.4 again,
but should be enabled on all generations in 3.5.
Conflicts:
drivers/gpu/drm/i915/intel_i2c.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEbBAABAgAGBQJPi3XOAAoJEHm+PkMAQRiGnsUH9RjHwH4YFVyuP/DKtKa6zs74
wqkpT15yITQ5WWMog4JaJFFg5rJCUd8QZr7AS/HSn0ijDyZX5VU7Rcs9cMudDzNR
H/5K/AscS4fjb0HwWVqoltTWHRb9QGSwVN3+E3VCDLt9P89YJ0o3QztkkuEX5dkZ
jc7reVXTfRnCcILEa9jleOzrn+OLM3j/jAjQ2hGunl8EDLzD4b17HHPoli4jEZ/5
5ibpSVsPD+AqzN+glbXvYjVItl12D0IQos/JdOwfuZriCVWLxysSSwHZTbPCyvBZ
LHH4HR5T+XLSXbjJeNkUFHLzqU+d5gVRadIoWtJCxqxFjKbOs2YtzJ5Ai0nDiw==
=kTkC
-----END PGP SIGNATURE-----
ASoC: Merge tag 'v3.4-rc3' into for-3.5
Linux 3.4-rc3 contains a bunch of Tegra changes which are conflicting
annoyingly with the new development that's going on for Tegra so merge
it up to resolve those conflicts.
Conflicts:
sound/soc/soc-core.c
sound/soc/tegra/tegra_i2s.c
sound/soc/tegra/tegra_spdif.c
This commit adds device tree support for the GART hardware available on
NVIDIA Tegra 20 SoCs.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=8He+
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
Pull block driver bits from Jens Axboe:
- A series of fixes for mtip32xx. Most from Asai at Micron, but also
one from Greg, getting rid of the dependency on PCIE_HOTPLUG.
- A few bug fixes for xen-blkfront, and blkback.
- A virtio-blk fix for Vivek, making resize actually work.
- Two fixes from Stephen, making larger transfers possible on cciss.
This is needed for tape drive support.
* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
mtip32xx: dump tagmap on failure
mtip32xx: fix handling of commands in various scenarios
mtip32xx: Shorten macro names
mtip32xx: misc changes
mtip32xx: Add new sysfs entry 'status'
mtip32xx: make setting comp_time as common
mtip32xx: Add new bitwise flag 'dd_flag'
mtip32xx: fix error handling in mtip_init()
virtio-blk: Call revalidate_disk() upon online disk resize
xen/blkback: Make optional features be really optional.
xen/blkback: Squash the discard support for 'file' and 'phy' type.
mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
cciss: Fix scsi tape io with more than 255 scatter gather elements
cciss: Initialize scsi host max_sectors for tape drive support
xen-blkfront: make blkif_io_lock spinlock per-device
xen/blkfront: don't put bdev right after getting it
xen-blkfront: use bitmap_set() and bitmap_clear()
xen/blkback: Enable blkback on HVM guests
xen/blkback: use grant-table.c hypercall wrappers
Documents how system call filtering using Berkeley Packet
Filter programs works and how it may be used.
Includes an example for x86 and a semi-generic
example using a macro-based code generator.
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Will Drewry <wad@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
v18: - added acked by
- update no new privs numbers
v17: - remove @compat note and add Pitfalls section for arch checking
(keescook@chromium.org)
v16: -
v15: -
v14: - rebase/nochanges
v13: - rebase on to 88ebdda615
v12: - comment on the ptrace_event use
- update arch support comment
- note the behavior of SECCOMP_RET_DATA when there are multiple filters
(keescook@chromium.org)
- lots of samples/ clean up incl 64-bit bpf-direct support
(markus@chromium.org)
- rebase to linux-next
v11: - overhaul return value language, updates (keescook@chromium.org)
- comment on do_exit(SIGSYS)
v10: - update for SIGSYS
- update for new seccomp_data layout
- update for ptrace option use
v9: - updated bpf-direct.c for SIGILL
v8: - add PR_SET_NO_NEW_PRIVS to the samples.
v7: - updated for all the new stuff in v7: TRAP, TRACE
- only talk about PR_SET_SECCOMP now
- fixed bad JLE32 check (coreyb@linux.vnet.ibm.com)
- adds dropper.c: a simple system call disabler
v6: - tweak the language to note the requirement of
PR_SET_NO_NEW_PRIVS being called prior to use. (luto@mit.edu)
v5: - update sample to use system call arguments
- adds a "fancy" example using a macro-based generator
- cleaned up bpf in the sample
- update docs to mention arguments
- fix prctl value (eparis@redhat.com)
- language cleanup (rdunlap@xenotime.net)
v4: - update for no_new_privs use
- minor tweaks
v3: - call out BPF <-> Berkeley Packet Filter (rdunlap@xenotime.net)
- document use of tentative always-unprivileged
- guard sample compilation for i386 and x86_64
v2: - move code to samples (corbet@lwn.net)
Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull block core bits from Jens Axboe:
"It's a nice and quiet round this time, since most of the tricky stuff
has been pushed to 3.5 to give it more time to mature. After a few
hectic block IO core changes for 3.3 and 3.2, I'm quite happy with a
slow round.
Really minor stuff in here, the only real functional change is making
the auto-unplug threshold a per-queue entity. The threshold is set so
that it's low enough that we don't hold off IO for too long, but still
big enough to get a nice benefit from the batched insert (and hence
queue lock cost reduction). For raid configurations, this currently
breaks down."
* 'for-3.4/core' of git://git.kernel.dk/linux-block:
block: make auto block plug flush threshold per-disk based
Documentation: Add sysfs ABI change for cfq's target latency.
block: Make cfq_target_latency tunable through sysfs.
block: use lockdep_assert_held for queue locking
block: blk_alloc_queue_node(): use caller's GFP flags instead of GFP_KERNEL
This patch implements the basic single data conversion support for
the SPEAr600 SoC ADC. The register layout of SPEAr600 differs a bit
from other SPEAr SoC variants (e.g. SPEAr3xx). These differences are
handled via DT compatible testing. Resulting in a multi-arch binary.
This driver is currently tested only on SPEAr600. Future patches may add
support for other SoC variants (SPEAr3xx) and features like software
buffer or DMA.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This provides an ASoC DAI interface for Tegra 30's I2S controller.
Includes a squashed bugfix from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AHUB (Audio Hub) is a mux/crossbar which links all audio-related
devices except the HDA controller on Tegra30. The devices include the
DMA FIFOs, DAM (Digital Audio Mixers), I2S controllers, and SPDIF
controller. Audio data may be routed between these devices in various
combinations as required by board design/application.
Includes a squashed bugfix from Nikesh Oswal <noswal@nvidia.com>
Includes squashed bugfixes from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit c172708 "regulator: core: Use a struct to pass in regulator runtime
configuration" changed the regulator_register() API signature.
Update the Documentation accordingly to reflect the change in the function
signature.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here are a number of fixes for the USB core and drivers for 3.4-rc2
Lots of tiny xhci fixes here, a few usb-serial driver fixes and new device ids,
and a smattering of other minor fixes in different USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+HVPUACgkQMUfUDdst+ykskwCfV0ypvXzg0JMTBqNDHb8BDmcZ
Ca4An0pZyzO2JsUHTfGUAvm6SFANqCnk
=KB61
-----END PGP SIGNATURE-----
Merge tag 'usb-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of fixes for the USB core and drivers for 3.4-rc2
Lots of tiny xhci fixes here, a few usb-serial driver fixes and new
device ids, and a smattering of other minor fixes in different USB
drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (30 commits)
USB: update usbtmc api documentation
xHCI: Correct the #define XHCI_LEGACY_DISABLE_SMI
xHCI: use gfp flags from caller instead of GFP_ATOMIC
xHCI: add XHCI_RESET_ON_RESUME quirk for VIA xHCI host
USB: fix bug of device descriptor got from superspeed device
xhci: Fix register save/restore order.
xhci: Restore event ring dequeue pointer on resume.
xhci: Don't write zeroed pointers to xHC registers.
xhci: Warn when hosts don't halt.
xhci: don't re-enable IE constantly
usb: xhci: fix section mismatch in linux-next
xHCI: correct to print the true HSEE of USBCMD
USB: serial: fix race between probe and open
UHCI: hub_status_data should indicate if ports are resuming
EHCI: keep track of ports being resumed and indicate in hub_status_data
USB: fix race between root-hub suspend and remote wakeup
USB: sierra: add support for Sierra Wireless MC7710
USB: ftdi_sio: fix race condition in TIOCMIWAIT, and abort of TIOCMIWAIT when the device is removed
USB: ftdi_sio: fix status line change handling for TIOCMIWAIT and TIOCGICOUNT
USB: don't ignore suspend errors for root hubs
...
Pull timer fixes from Thomas Gleixner:
"The itimer removal one is not strictly a fix, but I really wanted to
avoid a rebase of the urgent ones."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource: Load the ACPI PM clocksource asynchronously"
clockevents: tTack broadcast device mode change in tick_broadcast_switch_to_oneshot()
itimer: Use printk_once instead of WARN_ONCE
nohz: Fix stale jiffies update in tick_nohz_restart()
tick: Document TICK_ONESHOT config option
proc: stats: Use arch_idle_time for idle and iowait times if available
itimer: Schedule silent NULL pointer fixup in setitimer() for removal
Merge fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (14 patches)
panic: fix stack dump print on direct call to panic()
drivers/rtc/rtc-pl031.c: enable clock on all ST variants
Revert "mm: vmscan: fix misused nr_reclaimed in shrink_mem_cgroup_zone()"
hugetlb: fix race condition in hugetlb_fault()
drivers/rtc/rtc-twl.c: use static register while reading time
drivers/rtc/rtc-s3c.c: add placeholder for driver private data
drivers/rtc/rtc-s3c.c: fix compilation error
MAINTAINERS: add PCDP console maintainer
memcg: do not open code accesses to res_counter members
drivers/rtc/rtc-efi.c: fix section mismatch warning
drivers/rtc/rtc-r9701.c: reset registers if invalid values are detected
drivers/char/random.c: fix boot id uniqueness race
memcg: fix broken boolen expression
memcg: fix up documentation on global LRU
In v3.3-rc1, the global LRU was removed in commit 925b7673cc ("mm:
make per-memcg LRU lists exclusive"). The patch fixes up the memcg
docs.
I left the swap session to someone who has better understanding of
'memory+swap'.
Signed-off-by: Ying Han <yinghan@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct path names in API documentation for usbtmc
Signed-off-by: Stephen Lewis <lewis@sdf.lonestar.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
ids are not yet added, and there's still quite a few patches to merge
(mostly modesetting). To make QA easier I've decided to merge this stuff
in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
is a real frankenstein chip, but also hsw is stretching our driver's
code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
there are more patches needed (and some already queued up), but I wanted
to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
a few months already and a lot of i-g-t tests have been created for it.
Now it's finally ready to be merged. Note that one patch in this series
touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
driver we actually need to support by bailing out of unsupported case.
The driver now refuses to load without kms on gen6+ and disallows a few
ioctls that userspace never used in certain cases. More of this will
definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
in this way).
- Small fixlets and adjustements and some minor things to help debugging.
Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
drm/i915: VCS is not the last ring
drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
drm/i915: make quirks more verbose
drm/i915: dump the DMA fetch addr register on pre-gen6
drm/i915/sdvo: Include YRPB as an additional TV output type
drm/i915: disallow gem init ioctl on ilk
drm/i915: refuse to load on gen6+ without kms
drm/i915: extract gt interrupt handler
drm/i915: use render gen to switch ring irq functions
drm/i915: rip out old HWSTAM missed irq WA for vlv
drm/i915: open code gen6+ ring irqs
drm/i915: ring irq cleanups
drm/i915: add SFUSE_STRAP registers for digital port detection
drm/i915: add WM_LINETIME registers
drm/i915: add WRPLL clocks
drm/i915: add LCPLL control registers
drm/i915: add SSC offsets for SBI access
drm/i915: add port clock selection support for HSW
drm/i915: add S PLL control
drm/i915: add PIXCLK_GATE register
...
Conflicts:
drivers/char/agp/intel-agp.h
drivers/char/agp/intel-gtt.c
drivers/gpu/drm/i915/i915_debugfs.c
This second version of the bridge loop avoidance for batman-adv
avoids loops between the mesh and a backbone (usually a LAN).
By connecting multiple batman-adv mesh nodes to the same ethernet
segment a loop can be created when the soft-interface is bridged
into that ethernet segment. A simple visualization of the loop
involving the most common case - a LAN as ethernet segment:
node1 <-- LAN --> node2
| |
wifi <-- mesh --> wifi
Packets from the LAN (e.g. ARP broadcasts) will circle forever from
node1 or node2 over the mesh back into the LAN.
With this patch, batman recognizes backbone gateways, nodes which are
part of the mesh and backbone/LAN at the same time. Each backbone
gateway "claims" clients from within the mesh to handle them
exclusively. By restricting that only responsible backbone gateways
may handle their claimed clients traffic, loops are effectively
avoided.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Since there are still many Acer models that might not be covered by
the current fixup table, let's add back a few typical model names so
that user can test the fixup without recompiling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 00eacd6 ("ext3: make ext3 mount default to barrier=1") changed
the default barrier mount option for ext3. The documentation needs to
be updated, so this patch does that.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
This patch fixes following compilation warning:
Error: no ID for constraint linkend: v4l2-jpeg-chroma-subsampling.
and adds missing JPEG control class at the Table A.58.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These two IOCTLS are obsoleted by VIDIOC_SUBDEV_G_SELECTION and
VIDIOC_SUBDEV_S_SELECTION. Mark them obsolete.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add documentation for V4L2 subdev selection API. This changes also
experimental V4L2 subdev API so that scaling now works through selection API
only.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.
Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing the channel type during operation is
confusing to some drivers and will be hard to
handle in multi-channel scenarios. Instead of
changing the channel, set it to the right HT
channel before authenticating/associating and
don't change it -- just update the 20/40 MHz
restrictions in rate control as needed when
changed by the AP.
This also fixes a problem that Paul missed in
his fix for the "regulatory makes us deaf"
issue -- when we couldn't use 40 MHz we still
associated saying we were using 40 MHz, which
could in similarly broken APs make us never
even connect successfully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPgOpXAAoJEHm+PkMAQRiG8eUIAJ3Hjo0o5hqzxol8LWHDGF8s
3h59qwRtts82u2psStZULPLbBzw6yjn8U5Mcrh7pffwCG2BzBL5rXcmXfvoPaET3
TjylIj986Jv+jwZyuyZcLzYyoUtgjtq7hnt4tgVVEPlexYs7LxUl8vO8QjxT+bVO
7eKgzLsXlBC9kw4P5M7kOBQ9NE5vmEcKf+fB3Hu3DqfVJtw9Lb7EeDQj/cbQsGqI
vavSxe7lMTPsgMP2+hRz4txGTDJNRazkO2BdwfYrcNwTSa8tfBFlamww3y4+eJtq
MFQfdNxQpumh2++T4IC2i/nLaawH7kWj2EdaRCRLMy9hVlb/v8/wcgd+1nfLkU8=
=0on9
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc2' into for-3.5
Linux 3.4-rc2 contains some bug fixes we need, including the addition of
an export for regcache_sync_region().
* Add support for detecting the following device status
- write protect
- over temp (thermal shutdown)
* Add new sysfs entry 'status', possible values - online, write_protect, thermal_shutdown
* Add new file 'sysfs-block-rssd' to document ABI (Reported-by: Greg Kroah-Hartman)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
This is needed to catch the resume bug that was bothering lots of us from
testing some XHCI bug fixes in the suspend/resume path.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a flag that will tell the guest it was suspended, create an
interface for that communication using a KVM ioctl.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Deprecated in favour of tracepoints.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch (as1534c) updates the documentation for usb_unlink_urb and
related functions. It explains that the caller must prevent the URB
being unlinked from getting deallocated while the unlink is taking
place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The doc says that the data
| 55534243 5e000000 00000000 00000600 00000000 00000000 00000000 000000
is the SCSI command 0x5e. According to the usbmon source, it dumps one
byte after the other. The first 4 bytes are US_BULK_CB_SIGN which is
correct. After that we see the TAG which is 0x5e. The cdb is 0x00 in
this example.
In order to correct this, I change the example to a READ_10 command
which is 0x28 so it is not just a zero somewhere in the stream.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
ixp2xxx platforms have had no real changes since ~2006 and the maintainer
has said on irc that they can be removed:
13:05 < nico> do you still care about ixp2000?
13:22 < lennert> not really, no
13:58 < nico> do you think we could remove it from the kernel tree?
14:01 < lennert> go for it, and remove ixp23xx too while you're at it
Removing will help simplify ARM consolidation in general and PCI re-work
specifically.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Commit dc1f8bf68b ('netdev: change
transmit to limited range type') changed the required return type and
9a1654ba0b ('net: Optimize
hard_start_xmit() return checking') changed the valid numerical
return values.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08baf56108 ('net:
txq_trans_update() helper') made it unnecessary for most drivers to
set net_device::trans_start (or netdev_queue::trans_start).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits d314774cf2 ('netdev: network
device operations infrastructure') and
008298231a ('netdev: add more functions
to netdevice ops') moved and renamed net device operation pointers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits e308a5d806 ('netdev: Add
netdev->addr_list_lock protection.') and
e8a0464cc9 ('netdev: Allocate multiple
queues for TX.') introduced more fine-grained locks.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348eef ('[NET]: Make NAPI
polling independent of struct net_device objects.') removed the
automatic disabling of NAPI polling by dev_close(), and drivers
must now do this themselves.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bunch of fixes for regressions (and a few other problems) in 3.4-rc1:
* Fix for regression of mach/io.h cleanup on platforms with PCI or PCMCIA
(adding back the include file on those for now)
* AT91 fixes for usb and spi
* smsc911x ethernet fixes for i.MX
* smsc911x fixes for OMAP
* gpio fixes for Tegra
* A handful of build error and warning fixes for various platforms
* cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series, aren't
technically regressions for 3.4, but they're valid fixes and we're still
relatively early in the rc cycle so it seems appropriate to include them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RVTD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
Introduce new flags to automatically export GPIOs when using the convenience
functions gpio_request_one() or gpio_request_array(). This eases support for
custom boards where lots of GPIOs need to be exported for customer
applications.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull DMA mapping branch from Marek Szyprowski:
"Short summary for the whole series:
A few limitations have been identified in the current dma-mapping
design and its implementations for various architectures. There exist
more than one function for allocating and freeing the buffers:
currently these 3 are used dma_{alloc, free}_coherent,
dma_{alloc,free}_writecombine, dma_{alloc,free}_noncoherent.
For most of the systems these calls are almost equivalent and can be
interchanged. For others, especially the truly non-coherent ones
(like ARM), the difference can be easily noticed in overall driver
performance. Sadly not all architectures provide implementations for
all of them, so the drivers might need to be adapted and cannot be
easily shared between different architectures. The provided patches
unify all these functions and hide the differences under the already
existing dma attributes concept. The thread with more references is
available here:
http://www.spinics.net/lists/linux-sh/msg09777.html
These patches are also a prerequisite for unifying DMA-mapping
implementation on ARM architecture with the common one provided by
dma_map_ops structure and extending it with IOMMU support. More
information is available in the following thread:
http://thread.gmane.org/gmane.linux.kernel.cross-arch/12819
More works on dma-mapping framework are planned, especially in the
area of buffer sharing and managing the shared mappings (together with
the recently introduced dma_buf interface: commit d15bd7ee44
"dma-buf: Introduce dma buffer sharing mechanism").
The patches in the current set introduce a new alloc/free methods
(with support for memory attributes) in dma_map_ops structure, which
will later replace dma_alloc_coherent and dma_alloc_writecombine
functions."
People finally started piping up with support for merging this, so I'm
merging it as the last of the pending stuff from the merge window.
Looks like pohmelfs is going to wait for 3.5 and more external support
for merging.
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
common: DMA-mapping: add NON-CONSISTENT attribute
common: DMA-mapping: add WRITE_COMBINE attribute
common: dma-mapping: introduce mmap method
common: dma-mapping: remove old alloc_coherent and free_coherent methods
Hexagon: adapt for dma_map_ops changes
Unicore32: adapt for dma_map_ops changes
Microblaze: adapt for dma_map_ops changes
SH: adapt for dma_map_ops changes
Alpha: adapt for dma_map_ops changes
SPARC: adapt for dma_map_ops changes
PowerPC: adapt for dma_map_ops changes
MIPS: adapt for dma_map_ops changes
X86 & IA64: adapt for dma_map_ops changes
common: dma-mapping: introduce generic alloc() and free() methods
If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-works the internal GMAC DMA parameters
passed from the platform.
In the past, we only passed the pbl but, with new core,
other parameters can be passed and are mandatory on some
platforms.
New parameters are documented in stmmac.txt because this
patch has an impact for many platforms.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch explicitly defines the CSUM offload engine type which need
(not mandatory) to be passed from the platform code.
STMMAC core supports two check sum offload engine types- Type-1 & Type-2.
Also, there are STMMAC cores that do not have the check sum offload
capabilities.
The behaviour of Type-1 & Type-2 cores related to provision of checksum
increases the packet length for Type-1 cores by 2, as the checksum is appended
at the end of data packet and the same is made accountable in the DMA status.
The STMMAC cores beyond Version-3.5 provide HW interface registers which allows
the user to read the HW capabilities, while to support the previous cores the
information related to HW capabilities has to be provided from the platform
code.
The Type-1 cores which do not have the HW register interface need this
information.
This patch also updates the driver's doc.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h5VJ
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Remove non-existent parameter from fixed-helper.c kernel doc
regulator: Fix setting new voltage in s5m8767_set_voltage
regulator: fix sysfs name collision between dummy and fixed dummy regulator
regulator: Fix deadlock on removal of regulators with supplies
regulator: Fix comments in include/linux/regulator/machine.h
regulator: Only update [LDOx|DCx]_HIB_MODE bits in wm8350_[ldo|dcdc]_set_suspend_disable
regulator: Fix setting low power mode for wm831x aldo
regulator: Return microamps in wm8350_isink_get_current
regulator: wm8350: Fix the logic to choose best current limit setting
regulator: wm831x-isink: Fix the logic to choose best current limit setting
regulator: wm831x-dcdc: Fix the logic to choose best current limit setting
regulator: anatop: patching to device-tree property "reg".
regulator: Do proper shift to set correct bit for DC[2|5]_HIB_MODE setting
regulator: Fix restoring pmic.dcdcx_hib_mode settings in wm8350_dcdc_set_suspend_enable
regulator: Fix unbalanced lock/unlock in mc13892_regulator_probe error path
regulator: Fix set and get current limit for wm831x_buckv
regulator: tps6586x: Fix list minimal voltage setting for LDO0
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: Call restore_sched_clock_state() only after %gs is initialized
x86: Use -mno-avx when available
x86: Remove the ancient and deprecated disable_hlt() and enable_hlt() facility
x86: Preserve lazy irq disable semantics in fixup_irqs()
Add comments to NAND "gpios" property to make it clearer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Touch Ring LEDs on Intuos5 tablets use a different report
format which supports only 4 levels of brightness. We remap
the 7-bit value obtained from sysfs to an appropriate value
for the tablet. Control of the crop mark LEDs (new to the I5)
is left for a later patch.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The explanation of ip_local_port_range in
Documentation/networking/ip-sysctl.txt contains several factual
errors:
- The default value of ip_local_port_range does not depend on the
amount of memory available in the system.
- tcp_tw_recycle is not enabled by default.
- 1024-4999 is not the default value.
- Etc.
Clean up the mess.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change some broken links, remove obsolete information and add
information about the CRISv32 architecture.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Pull HSI (High Speed Synchronous Serial Interface) framework from Carlos Chinea:
"The High Speed Synchronous Serial Interface (HSI) is a serial
interface mainly used for connecting application engines (APE) with
cellular modem engines (CMT) in cellular handsets.
The framework is currently being used for some people and we would
like to see it integrated into the kernel for 3.3. There is no HW
controller drivers in this pull, but some people have already some of
them pending which they would like to push as soon as this integrated.
I am also working on the acceptance for an TI OMAP one, based on a
compatible legacy version of the interface called SSI."
Ok, so it didn't get into 3.3, but here it is pulled into 3.4.
Several people piped up to say "yeah, we want this".
* 'for-next' of git://gitorious.org/kernel-hsi/kernel-hsi:
HSI: hsi_char: Update ioctl-number.txt
HSI: Add HSI API documentation
HSI: hsi_char: Add HSI char device kernel configuration
HSI: hsi_char: Add HSI char device driver
HSI: hsi: Introducing HSI framework
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W59/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Pull cpumask cleanups from Rusty Russell:
"(Somehow forgot to send this out; it's been sitting in linux-next, and
if you don't want it, it can sit there another cycle)"
I'm a sucker for things that actually delete lines of code.
Fix up trivial conflict in arch/arm/kernel/kprobes.c, where Rusty fixed
a user of &cpu_online_map to be cpu_online_mask, but that code got
deleted by commit b21d55e98a ("ARM: 7332/1: extract out code patch
function from kprobes").
* tag 'for-linus' of git://github.com/rustyrussell/linux:
cpumask: remove old cpu_*_map.
documentation: remove references to cpu_*_map.
drivers/cpufreq/db8500-cpufreq: remove references to cpu_*_map.
remove references to cpu_*_map in arch/
This patch marks the following features for deprecation.
* Rebinding subsys by remount: Never reached useful state - only works
on empty hierarchies.
* release_agent update by remount: release_agent itself will be
replaced with conventional fsnotify notification.
v2: Lennart pointed out that "name=" is necessary for mounts w/o any
controller attached. Drop "name=" deprecation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
The on-chip northbridge's temperature sensor of the upcoming
AMD Trinity CPUs works the same as for the previous CPUs.
Since it has a different PCI-ID, we just add the new one to the list
supported by k10temp.
This allows to use the k10temp driver on those CPUs.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add DAPM widgets and audio routing support for imx-sgtl5000 machine
driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the initial imx-sgtl5000 machine driver support with only
playback dai link implemented. More features can be added on top
of it later.
It's a device tree only machine driver working with fsl_ssi driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull perf updates and fixes from Ingo Molnar:
"It's mostly fixes, but there's also two late items:
- preliminary GTK GUI support for perf report
- PMU raw event format descriptors in sysfs, to be parsed by tooling
The raw event format in sysfs is a new ABI. For example for the 'CPU'
PMU we have:
aldebaran:~> ll /sys/bus/event_source/devices/cpu/format/*
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/any
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/cmask
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/edge
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/event
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/inv
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/offcore_rsp
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/pc
-r--r--r--. 1 root root 4096 Mar 31 10:29 /sys/bus/event_source/devices/cpu/format/umask
those lists of fields contain a specific format:
aldebaran:~> cat /sys/bus/event_source/devices/cpu/format/offcore_rsp
config1:0-63
So, those who wish to specify raw events can now use the following
event format:
-e cpu/cmask=1,event=2,umask=3
Most people will not want to specify any events (let alone raw
events), they'll just use whatever default event the tools use.
But for more obscure PMU events that have no cross-architecture
generic events the above syntax is more usable and a bit more
structured than specifying hex numbers."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
perf tools: Remove auto-generated bison/flex files
perf annotate: Fix off by one symbol hist size allocation and hit accounting
perf tools: Add missing ref-cycles event back to event parser
perf annotate: addr2line wants addresses in same format as objdump
perf probe: Finder fails to resolve function name to address
tracing: Fix ent_size in trace output
perf symbols: Handle NULL dso in dso__name_len
perf symbols: Do not include libgen.h
perf tools: Fix bug in raw sample parsing
perf tools: Fix display of first level of callchains
perf tools: Switch module.h into export.h
perf: Move mmap page data_head offset assertion out of header
perf: Fix mmap_page capabilities and docs
perf diff: Fix to work with new hists design
perf tools: Fix modifier to be applied on correct events
perf tools: Fix various casting issues for 32 bits
perf tools: Simplify event_read_id exit path
tracing: Fix ftrace stack trace entries
tracing: Move the tracing_on/off() declarations into CONFIG_TRACING
perf report: Add a simple GTK2-based 'perf report' browser
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
Pull core locking updates from Thomas Gleixner.
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Mark get_robust_list as deprecated
futex: Do not leak robust list to unprivileged process
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
- A quite complex ab8500 charger driver, submitted by
Arun Murthy @ ST-Ericsson;
- Summit Microelectronics SMB347 Battery Charger, submitted by
Bruce E. Robertson and Alan Cox @ Intel.
And that's all.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPdhj7AAoJEGgI9fZJve1bSKEQAKzKXPwqpBREXzS888YWzb34
0r3Bly+F8eSRTjclbEEvEOVVCjxKOFpow5lN+eAkRNAMLDBcMamfBTR+rpoYb822
d7R4Hy/stVnmD5nul0WMezZ0OZf6qRy8kHazmvb63Jk37ykof52TqoEInKdHL/ww
afUNfCnAFAbZkjxEr/9MwpM+nzYKdlGIoQlu9CJLARJiT9CyICjgHG48MGmyxOws
1LPha40jXuKLoyE+6nvG1Ji71NzZlFaVuFpzk75kjsWoB78zkRsMSv+zboHRz3QP
PI+uS54auIkGhqeIeEuuSzPZx+1K2Fr2/qyut3tqM8AejBE4kETiBAy0b0BREBSd
NqA4/Yw24c8xglIFP6OlNjHnLgCsExfHATzqzML2El/dXG8P2ggEayZzDh9bmsuU
ZNKOmHZYgEj2eEorJcmlfZ23rJwlxuspl1m2nH2WEnqw6Z6TnskK4N1JSNlpGRPU
j+iHbTPA04hultQkzNHCdPRR/jK1IC5eGdwc612QgxOhZPkvhmW92e8EOVz/3E3X
TqKXfBiKxKtkIncLPYFh7oeZINKnlqZrXsYrHhxhlm9UstGOqfEIqbCGqlf0Q4P1
WOhIQe1cP/JpB9T58e3mLF2dQIGScTqzQCRSW6/m+3HmDwZb8JyUQRw5188s3yJr
umrBS5hqS+z3bISWrcGi
=Y8fe
-----END PGP SIGNATURE-----
Merge tag 'for-v3.4-rc1' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Various small bugfixes and enhancements, plus two new drivers:
- A quite complex ab8500 charger driver, submitted by Arun Murthy @
ST-Ericsson;
- Summit Microelectronics SMB347 Battery Charger, submitted by Bruce
E Robertson and Alan Cox @ Intel.
And that's all."
* tag 'for-v3.4-rc1' of git://git.infradead.org/battery-2.6: (36 commits)
max17042_battery: Clean up interrupt handling
Revert "max8998_charger: Include linux/module.h just once"
ab8500_fg: Fix some build warnings on x86_64
max17042_battery: Fix CHARGE_FULL representation.
max8998_charger: Include linux/module.h just once
power_supply: Convert i2c drivers to module_i2c_driver
lp8727_charger: Add MODULE_DEVICE_TABLE
charger-manager: Simplify charger_get_property(), get rid of a warning
charger-manager: Clean up for better readability
da9052-battery: Convert to use module_platform_driver
da9052-battery: Fix a memory leak when unload the module
da9052-battery: Add missing platform_set_drvdata
ab8500: Turn unneeded global symbols into local ones
ab8500_fg: Fix copy-paste error
ab8500_fg: Get rid of 'struct battery_type'
ab8500_fg: Get rid of 'struct v_to_cap'
ab8500_btemp: Get rid of 'enum adc_therm'
ab8500_charger: Convert to the new USB OTG calls
ab8500-btemp: AB8500 battery temperature driver
ab8500-fg: A8500 fuel gauge driver
...
Install commands should not be used to specify soft dependencies among
modules. When loading modules it's much better to have a softdep that
modprobe knows what's being done than having to fork/exec another
instance of modprobe to load the other module.
By using a softdep user has also an option to remove the dependencies
when removing the module (and if its refcount dropped to 0)
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clarify that the 'cat' command does not include the (c, 13, 32)
after it.
Reported-by: Dan Jidanni Jacobson <jidanni@jidanni.org>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kconfig documentation suggests using plain 'diff' to compare config
files and then adds "Yes, we need something better here". Commit
a717417e7f ("kconfig: add diffconfig utility") added what that comment
was looking for.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mach entry in the dontdiff file causes all the
arch/arm/mach-*/include/mach directories to be skipped.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/acpi/apei/apei-base.c
This was a conflict between
15afae6046
(CPI, APEI: Fix incorrect APEI register bit width check and usage)
and
653f4b538f
(ACPICA: Expand OSL memory read/write interfaces to 64 bits)
The former changed a parameter in the call to acpi_os_read_memory64()
and the later replaced all calls to acpi_os_read_memory64()
with calls to acpi_os_read_memory().
Signed-off-by: Len Brown <len.brown@intel.com>
setitimer() should return -EFAULT if called with an invalid pointer
for value. The current code excludes a NULL pointer from this rule and
silently uses it to stop the timer. This violates the spec.
Warn about user space apps which rely on that feature and schedule it
for removal.
[ tglx: Massaged changelog, warn message and Doc entry ]
Signed-off-by: Sasikantha babu <sasikanth.v19@gmail.com>
Link: http://lkml.kernel.org/r/1332340854-26053-1-git-send-email-sasikanth.v19@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ACPI 5.0 adds the BGRT, a table that contains a pointer to the firmware
boot splash and associated metadata. This simple driver exposes it via
/sys/firmware/acpi in order to allow bootsplash applications to draw their
splash around the firmware image and reduce the number of jarring graphical
transitions during boot.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add description of parameter notrigger in the einj.txt.
One can utilize this new parameter to do some SRAR injection
test. Pay attention, the operation is highly depended on the
BIOS implementation. If no proper BIOS supports it, even if
enabling this parameter, expected result will not happen.
v2:
Update the documentation suggested by Tony
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The X86_32-only disable_hlt/enable_hlt mechanism was used by the
32-bit floppy driver. Its effect was to replace the use of the
HLT instruction inside default_idle() with cpu_relax() - essentially
it turned off the use of HLT.
This workaround was commented in the code as:
"disable hlt during certain critical i/o operations"
"This halt magic was a workaround for ancient floppy DMA
wreckage. It should be safe to remove."
H. Peter Anvin additionally adds:
"To the best of my knowledge, no-hlt only existed because of
flaky power distributions on 386/486 systems which were sold to
run DOS. Since DOS did no power management of any kind,
including HLT, the power draw was fairly uniform; when exposed
to the much hhigher noise levels you got when Linux used HLT
caused some of these systems to fail.
They were by far in the minority even back then."
Alan Cox further says:
"Also for the Cyrix 5510 which tended to go castors up if a HLT
occurred during a DMA cycle and on a few other boxes HLT during
DMA tended to go astray.
Do we care ? I doubt it. The 5510 was pretty obscure, the 5520
fixed it, the 5530 is probably the oldest still in any kind of
use."
So, let's finally drop this.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephen Hemminger <shemminger@vyatta.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/n/tip-3rhk9bzf0x9rljkv488tloib@git.kernel.org
[ If anyone cares then alternative instruction patching could be
used to replace HLT with a one-byte NOP instruction. Much simpler. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some C states of new CPU might be not good. One reason is BIOS might
configure them incorrectly. To help developers root cause it quickly, the
patch adds a new sysfs entry, so developers could disable specific C state
manually.
In addition, C state might have much impact on performance tuning, as it
takes much time to enter/exit C states, which might delay interrupt
processing. With the new debug option, developers could check if a deep C
state could impact performance and how much impact it could cause.
Also add this option in Documentation/cpuidle/sysfs.txt.
[akpm@linux-foundation.org: check kstrtol return value]
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Reviewed-by: Yanmin Zhang <yanmin_zhang@intel.com>
Reviewed-and-Tested-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
v2: 2nd draft
- Editorial cleanups (Randy Dunlap and Stephen Warren)
- Added missing Microblaze reference (Stephen Neuendorffer)
- Make example of platform_device creation clearer (Shawn Guo)
- Expand on PowerPC history and mention i2c mess (David Gibson)
- convert to plain text (remove bits of html formating)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull x32 support for x86-64 from Ingo Molnar:
"This tree introduces the X32 binary format and execution mode for x86:
32-bit data space binaries using 64-bit instructions and 64-bit kernel
syscalls.
This allows applications whose working set fits into a 32 bits address
space to make use of 64-bit instructions while using a 32-bit address
space with shorter pointers, more compressed data structures, etc."
Fix up trivial context conflicts in arch/x86/{Kconfig,vdso/vma.c}
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
x32: Fix alignment fail in struct compat_siginfo
x32: Fix stupid ia32/x32 inversion in the siginfo format
x32: Add ptrace for x32
x32: Switch to a 64-bit clock_t
x32: Provide separate is_ia32_task() and is_x32_task() predicates
x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls
x86/x32: Fix the binutils auto-detect
x32: Warn and disable rather than error if binutils too old
x32: Only clear TIF_X32 flag once
x32: Make sure TS_COMPAT is cleared for x32 tasks
fs: Remove missed ->fds_bits from cessation use of fd_set structs internally
fs: Fix close_on_exec pointer in alloc_fdtable
x32: Drop non-__vdso weak symbols from the x32 VDSO
x32: Fix coding style violations in the x32 VDSO code
x32: Add x32 VDSO support
x32: Allow x32 to be configured
x32: If configured, add x32 system calls to system call tables
x32: Handle process creation
x32: Signal-related system calls
x86: Add #ifdef CONFIG_COMPAT to <asm/sys_ia32.h>
...
Pull nfsd changes from Bruce Fields:
Highlights:
- Benny Halevy and Tigran Mkrtchyan implemented some more 4.1 features,
moving us closer to a complete 4.1 implementation.
- Bernd Schubert fixed a long-standing problem with readdir cookies on
ext2/3/4.
- Jeff Layton performed a long-overdue overhaul of the server reboot
recovery code which will allow us to deprecate the current code (a
rather unusual user of the vfs), and give us some needed flexibility
for further improvements.
- Like the client, we now support numeric uid's and gid's in the
auth_sys case, allowing easier upgrades from NFSv2/v3 to v4.x.
Plus miscellaneous bugfixes and cleanup.
Thanks to everyone!
There are also some delegation fixes waiting on vfs review that I
suppose will have to wait for 3.5. With that done I think we'll finally
turn off the "EXPERIMENTAL" dependency for v4 (though that's mostly
symbolic as it's been on by default in distro's for a while).
And the list of 4.1 todo's should be achievable for 3.5 as well:
http://wiki.linux-nfs.org/wiki/index.php/Server_4.0_and_4.1_issues
though we may still want a bit more experience with it before turning it
on by default.
* 'for-3.4' of git://linux-nfs.org/~bfields/linux: (55 commits)
nfsd: only register cld pipe notifier when CONFIG_NFSD_V4 is enabled
nfsd4: use auth_unix unconditionally on backchannel
nfsd: fix NULL pointer dereference in cld_pipe_downcall
nfsd4: memory corruption in numeric_name_to_id()
sunrpc: skip portmap calls on sessions backchannel
nfsd4: allow numeric idmapping
nfsd: don't allow legacy client tracker init for anything but init_net
nfsd: add notifier to handle mount/unmount of rpc_pipefs sb
nfsd: add the infrastructure to handle the cld upcall
nfsd: add a header describing upcall to nfsdcld
nfsd: add a per-net-namespace struct for nfsd
sunrpc: create nfsd dir in rpc_pipefs
nfsd: add nfsd4_client_tracking_ops struct and a way to set it
nfsd: convert nfs4_client->cl_cb_flags to a generic flags field
NFSD: Fix nfs4_verifier memory alignment
NFSD: Fix warnings when NFSD_DEBUG is not defined
nfsd: vfs_llseek() with 32 or 64 bit offsets (hashes)
nfsd: rename 'int access' to 'int may_flags' in nfsd_open()
ext4: return 32/64-bit dir name hash according to usage type
fs: add new FMODE flags: FMODE_32bithash and FMODE_64bithash
...
Pull x86 updates from Ingo Molnar.
This touches some non-x86 files due to the sanitized INLINE_SPIN_UNLOCK
config usage.
Fixed up trivial conflicts due to just header include changes (removing
headers due to cpu_idle() merge clashing with the <asm/system.h> split).
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/amd: Be more verbose about LVT offset assignments
x86, tls: Off by one limit check
x86/ioapic: Add io_apic_ops driver layer to allow interception
x86/olpc: Add debugfs interface for EC commands
x86: Merge the x86_32 and x86_64 cpu_idle() functions
x86/kconfig: Remove CONFIG_TR=y from the defconfigs
x86: Stop recursive fault in print_context_stack after stack overflow
x86/io_apic: Move and reenable irq only when CONFIG_GENERIC_PENDING_IRQ=y
x86/apic: Add separate apic_id_valid() functions for selected apic drivers
locking/kconfig: Simplify INLINE_SPIN_UNLOCK usage
x86/kconfig: Update defconfigs
x86: Fix excessive MSR print out when show_msr is not specified
Notify get_robust_list users that the syscall is going away.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: kernel-hardening@lists.openwall.com
Cc: spender@grsecurity.net
Link: http://lkml.kernel.org/r/20120323190855.GA27213@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=T4T+
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: sh_mmcif: simplify bitmask macros
mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
mmc: sh_mobile_sdhi: add a callback for board specific init code
mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
mmc: sh_mobile_sdhi: do not manage PM clocks manually
mmc: tmio_mmc: remove unused sdio_irq_enabled flag
mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
mmc: tmio: calculate the native hotplug condition only once
mmc: simplify mmc_cd_gpio_request() by removing two parameters
mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
mmc: sdhci: check interrupt flags in ISR again
mmc: sdhci-pci: Add MSI support
mmc: core: warn when card doesn't support HPI
mmc: davinci: Poll status for small size transfers
mmc: davinci: Eliminate spurious interrupts
mmc: omap_hsmmc: Avoid a regulator voltage change with dt
mmc: omap_hsmmc: Convert hsmmc driver to use device tree
mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
...
Merge third batch of patches from Andrew Morton:
- Some MM stragglers
- core SMP library cleanups (on_each_cpu_mask)
- Some IPI optimisations
- kexec
- kdump
- IPMI
- the radix-tree iterator work
- various other misc bits.
"That'll do for -rc1. I still have ~10 patches for 3.4, will send
those along when they've baked a little more."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
backlight: fix typo in tosa_lcd.c
crc32: add help text for the algorithm select option
mm: move hugepage test examples to tools/testing/selftests/vm
mm: move slabinfo.c to tools/vm
mm: move page-types.c from Documentation to tools/vm
selftests/Makefile: make `run_tests' depend on `all'
selftests: launch individual selftests from the main Makefile
radix-tree: use iterators in find_get_pages* functions
radix-tree: rewrite gang lookup using iterator
radix-tree: introduce bit-optimized iterator
fs/proc/namespaces.c: prevent crash when ns_entries[] is empty
nbd: rename the nbd_device variable from lo to nbd
pidns: add reboot_pid_ns() to handle the reboot syscall
sysctl: use bitmap library functions
ipmi: use locks on watchdog timeout set on reboot
ipmi: simplify locking
ipmi: fix message handling during panics
ipmi: use a tasklet for handling received messages
ipmi: increase KCS timeouts
ipmi: decrease the IPMI message transaction time in interrupt mode
...
hugepage-mmap.c, hugepage-shm.c and map_hugetlb.c in Documentation/vm are
simple pass/fail tests, It's better to promote them to
tools/testing/selftests.
Thanks suggestion of Andrew Morton about this. They all need firstly
setting up proper nr_hugepages and hugepage-mmap need to mount hugetlbfs.
So I add a shell script run_vmtests to do such work which will call the
three test programs and check the return value of them.
Changes to original code including below:
a. add run_vmtests script
b. return error when read_bytes mismatch with writed bytes.
c. coding style fixes: do not use assignment in if condition
[akpm@linux-foundation.org: build the targets before trying to execute them]
[akpm@linux-foundation.org: Documentation/vm/ no longer has a Makefile. Fixes "make clean"]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tools/ is the better place for vm tools which are used by many people.
Moving them to tools also make them open to more users instead of hide in
Documentation folder.
This patch moves page-types.c to tools/vm/page-types.c. Also add a
Makefile in tools/vm and fix two coding style problems: a) change const
arrary to 'const char * const', b) change a space to tab for indent.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Partitions are described in the same way for all mtd devices when using
devicetree, move the documentation to a separate file and add references
to it.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull dma-buf updates from Sumit Semwal:
"This includes the following key items:
- kernel cpu access support,
- flag-passing to dma_buf_fd,
- relevant Documentation updates, and
- some minor cleanups and fixes.
These changes are needed for the drm prime/dma-buf interface code that
Dave Airlie plans to submit in this merge window."
* 'for-linus-3.4' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: correct dummy function declarations.
dma-buf: document fd flags and O_CLOEXEC requirement
dma_buf: Add documentation for the new cpu access support
dma-buf: add support for kernel cpu access
dma-buf: don't hold the mutex around map/unmap calls
dma-buf: add get_dma_buf()
dma-buf: pass flags into dma_buf_fd.
dma-buf: add dma_data_direction to unmap dma_buf_op
dma-buf: Move code out of mutex-protected section in dma_buf_attach()
dma-buf: Return error instead of using a goto statement when possible
dma-buf: Remove unneeded sanity checks
dma-buf: Constify ops argument to dma_buf_export()
Pull kvm updates from Avi Kivity:
"Changes include timekeeping improvements, support for assigning host
PCI devices that share interrupt lines, s390 user-controlled guests, a
large ppc update, and random fixes."
This is with the sign-off's fixed, hopefully next merge window we won't
have rebased commits.
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (130 commits)
KVM: Convert intx_mask_lock to spin lock
KVM: x86: fix kvm_write_tsc() TSC matching thinko
x86: kvmclock: abstract save/restore sched_clock_state
KVM: nVMX: Fix erroneous exception bitmap check
KVM: Ignore the writes to MSR_K7_HWCR(3)
KVM: MMU: make use of ->root_level in reset_rsvds_bits_mask
KVM: PMU: add proper support for fixed counter 2
KVM: PMU: Fix raw event check
KVM: PMU: warn when pin control is set in eventsel msr
KVM: VMX: Fix delayed load of shared MSRs
KVM: use correct tlbs dirty type in cmpxchg
KVM: Allow host IRQ sharing for assigned PCI 2.3 devices
KVM: Ensure all vcpus are consistent with in-kernel irqchip settings
KVM: x86 emulator: Allow PM/VM86 switch during task switch
KVM: SVM: Fix CPL updates
KVM: x86 emulator: VM86 segments must have DPL 3
KVM: x86 emulator: Fix task switch privilege checks
arch/powerpc/kvm/book3s_hv.c: included linux/sched.h twice
KVM: x86 emulator: correctly mask pmc index bits in RDPMC instruction emulation
KVM: mmu_notifier: Flush TLBs before releasing mmu_lock
...
Pull module and param updates from Rusty Russell:
"I'm getting married next week, and then honeymoon until 6th May. I'll
be offline from next week, except to post the compulsory pictures if
Alex shaves her head..."
I'm sure Rusty can take time off from his honeymoon if something comes
up. And here's the explanation about head shaving:
http://baldalex.org/
in case you wondered and wanted to support another insane caper or
Rusty's involving shaving.
What *is* it with Rusty and shaving, anyway?
* git://github.com/rustyrussell/linux:
module: Remove module size limit
module: move __module_get and try_module_get() out of line.
params: <level>_initcall-like kernel parameters
module_param: remove support for bool parameters which are really int.
module: add kernel param to force disable module load
Pull x86 platform driver updates from Matthew Garrett:
"Some significant updates to samsung-laptop, additional hardware
support for Toshibas, misc updates to various hardware and a new
backlight driver for some Apple machines."
Fix up trivial conflicts: geode Geos update happening next to net5501
support, and MSIC thermal platform support added twice.
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (77 commits)
acer-wmi: add quirk table for video backlight vendor mode
drivers/platform/x86/amilo-rfkill.c::amilo_rfkill_probe() avoid NULL deref
samsung-laptop: unregister ACPI video module for some well known laptops
acer-wmi: No wifi rfkill on Sony machines
thinkpad-acpi: recognize Lenovo as version string in newer V-series BIOS
asus-wmi: don't update power and brightness when using scalar
eeepc-wmi: split et2012 specific hacks
eeepc-wmi: refine quirks handling
asus-nb-wmi: set panel_power correctly
asus-wmi: move WAPF variable into quirks_entry
asus-wmi: store backlight power status for AIO machine
asus-wmi: add scalar board brightness adj. support
samsung-laptop: cleanup return type: mode_t vs umode_t
drivers, samsung-laptop: fix usage of isalnum
drivers, samsung-laptop: fix initialization of sabi_data in sabi_set_commandb
asus-wmi: on/off bit is not set when reading the value
eeepc-wmi: add extra keymaps for EP121
asus-nb-wmi: ignore useless keys
acer-wmi: support Lenovo ideapad S205 Brazos wifi switch
acer-wmi: fix out of input parameter size when set
...
Pull i2c updates from Jean Delvare.
Fix up trivial conflict in drivers/i2c/busses/i2c-gpio.c due to include
file cleanup clashing with DT support addition (which did the same
cleanup)
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-algo-bit: Don't resched on clock stretching
i2c: Update the FSF address
i2c: Convert drivers/i2c/muxes/* to use module_i2c_driver()
i2c-i801: Use usleep_range to wait for command completion
i2c-i801: Add device IDs for Intel Lynx Point
i2c-isch: Decrease delay in command completion check loop
i2c-gpio: Use linux/gpio.h rather than asm/gpio.h
Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPcWQxAAoJEEFnBt12D9kB4NEQAKzyQFFyX/1ZGZaKH12OtcSf
DSQg/2lx9MIOISYYjsq6cQQGeUnlvaFxYkKkS+P4U6aNqw6xRaEtFhef6mVTWeFL
PNi81hXIkyzza9/lZkoK4IBSk09JBeJu+5t9BwGQnM4Yg2POqqOf+vICWF0iN6mt
TtNXJb6vqHiveMsUIRP8AdZzVpSztVo5//wAri7om77Qm+3aJiptt65zz0ghKRT8
Tzb61miqUS7XS3NdUYq8pTsh8J1E8rrRch5jJWsY/AmVr0Dhajv5ouOiyp43EpHZ
mTNP90zglT3c+CTfRIb9oALfjPA5O+3ncSyBSB4qOX1nLcKyFvheg5uozyx7NSNJ
Pw4M8fCnKXN20sCbHQB0bTF0ETW5fuMAiKhGCU+4GpsIKelZKqRcWS7Dho8RquW+
YLuDXJWVut4HyyvrPFJxPs1IuOYCKJ2pGqDEzznEPgkVSxX4vedGE1MzKtj+aHFH
oZuZLOa+WQcyGLkW1BRsJxTht5i1paE5D9bXZfLkOgDMmFMBZ/oe6mLj26WCb3UL
lhxoAgFUKKe1+YBzkLISRf09L0rdhzEjs59ryK/ZVOuizH2+STKvH3jNSxuroAnN
ZCuomdofKNY/2pv3q3pAwm3G20l0qMwAqAVqYjF09m/jfDhcquHS5UoTvMG5WZqv
TGUh/kfetnPB07F0CLGQ
=BSW8
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO changes for v3.4 from Grant Likely:
"Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties."
Fix up context conflict due to Laxman Dewangan adding sleep control for
the tps65910 driver separately for gpio's and regulators.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio/ep93xx: Remove unused inline function and useless pr_err message
gpio/sodaville: Mark broken due to core irqdomain migration
gpio/omap: fix redundant decoding of gpio offset
gpio/omap: fix incorrect update to context.irqenable1
gpio/omap: fix incorrect context restore logic in omap_gpio_runtime_*
gpio/omap: fix missing dataout context save in _set_gpio_dataout_reg
gpio/omap: fix _set_gpio_irqenable implementation
gpio/omap: fix trigger type to unsigned
gpio/omap: fix wakeup_en register update in _set_gpio_wakeup()
gpio: tegra: tegra_gpio_config shouldn't be __init
gpio/davinci: fix enabling unbanked GPIO IRQs
gpio/davinci: fix oops on unbanked gpio irq request
gpio/omap: Fix section warning for omap_mpuio_alloc_gc()
ARM: tegra: export tegra_gpio_{en,dis}able
gpio/gpio-stmpe: Fix the value returned by _get_value routine
Documentation/gpio.txt: Explain expected pinctrl interaction
GPIO: LPC32xx: Add output reading to GPO P3
GPIO: LPC32xx: Fix missing bit selection mask
gpio/omap: fix wakeups on level-triggered GPIOs
gpio/omap: Fix IRQ handling for SPARSE_IRQ
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=onDl
-----END PGP SIGNATURE-----
Merge tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
- 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
TI's TPS65090 and TPS65217.
- New variants support (8420, 8520 ab9540), cleanups and bug fixes for
the abx500 and db8500 ST-E chipsets.
- Some minor fixes and update for the wm8994 from Mark.
- The beginning of a long term TWL cleanup effort coming from the TI
folks.
- Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
drivers.
Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).
* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
gpio/twl: Add DT support to gpio-twl4030 driver
gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
mfd: Detach twl6040 from the pmic mfd driver
mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
mfd: Micro-optimization on twl4030 IRQ handler
mfd: Make twl4030 SIH SPARSE_IRQ capable
mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
mfd: Remove references already defineid in header file from twl-core
mfd: Remove unneeded header from twl-core
mfd: Make twl-core not depend on pdata->irq_base/end
ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
mfd: Return twl6030_mmc_card_detect IRQ for board setup
Revert "mfd: Add platform data for MAX8997 haptic driver"
mfd: Add support for TPS65090
mfd: Add some da9052-i2c section annotations
mfd: Build rtc5t583 only if I2C config is selected to y.
mfd: Add anatop mfd driver
mfd: Fix compilation error in tps65910.h
mfd: Add 8420 variant to db8500-prcmu
mfd: Add 8520 PRCMU variant to db8500-prcmu
...
Pull watchdog updates from Wim Van Sebroeck:
- Removal of the Documentation/watchdog/00-INDEX file
- Fix boot status reporting for imx2_wdt
- clean-up sp805_wdt, pnx4008_wdt and mpcore_wdt
- convert printk in watchdog drivers to pr_ functions
- change nowayout module parameter to bool for every watchdog device
- conversion of jz4740_wdt, pnx4008_wdt, max63xx_wdt, softdog,
ep93xx_wdt, coh901327 and txx9wdt to new watchdog API
- Add support for the WDIOC_GETTIMELEFT ioctl call to the new watchdog
API
- Change the new watchdog API so that the driver updates the timeout
value
- two fixes for the xen_wdt driver
Fix up conflicts in ep93xx driver due to the same patches being merged
through separate branches.
* git://www.linux-watchdog.org/linux-watchdog: (33 commits)
watchdog: txx9wdt: fix timeout
watchdog: Convert txx9wdt driver to watchdog framework
watchdog: coh901327_wdt.c: fix timeout
watchdog: coh901327: convert to use watchdog core
watchdog: Add support for WDIOC_GETTIMELEFT IOCTL in watchdog core
watchdog: ep93xx_wdt: timeout is an unsigned int value.
watchdog: ep93xx_wdt: Fix timeout after conversion to watchdog core
watchdog: Convert ep93xx driver to watchdog core
watchdog: sp805: Use devm routines
watchdog: sp805: replace readl/writel with lighter _relaxed variants
watchdog: sp805: Fix documentation style comment
watchdog: mpcore_wdt: Allow platform_get_irq() to fail
watchdog: mpcore_wdt: Use devm routines
watchdog: mpcore_wdt: Rename dev to pdev for pointing to struct platform_device
watchdog: xen: don't clear is_active when xen_wdt_stop() failed
watchdog: xen: don't unconditionally enable the watchdog during resume
watchdog: fix compiler error for missing parenthesis
watchdog: ep93xx_wdt.c: fix platform probe
watchdog: ep93xx: Convert the watchdog driver into a platform device.
watchdog: fix set_timeout operations
...
- Update thin provisioning to support read-only external snapshot origins and
discards.
- A new target, dm verity, for device content validation.
- Mark dm uevent and dm raid as no-longer-experimental.
- Miscellaneous other fixes and clean-ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPc1BTAAoJEK2W1qbAHj1nrkAP/3pz9iWA+/t4mphBf5r6Fjgt
fV0WtyWyneUoWeUrVcs356W5xO1j1Vdj5tH/8sRA9eRQjs/9n4m2QoYea0yKtS1t
Y7/eqf6rXCRQaf9AwmFZHf8aHZA0o4K7NW7l1DvizuyckZJHNdbR1QW9XBbLS8IX
oWg53A6bXcq+duxPO2YUKb+vCjEHYs0WUxafvpQPbx9g7rZiQFaiSPT6BSUMTtmQ
vjiqg/bIA3kia7rT0oBV6SHU+o7xBffJXsgUeQ1U30JIsb8wLkRS5KwOlby/Vafg
1W/vT+uVR4ZLv77Ze0UWQDjny4N+jN9EFpBH7LZHYff3WnMUEhYHW3dmGlRxpZzI
2tr06X9JublnkuIlfNrGewFvuusODIiJkI36VlFVt2OWNijmOEFLXyUwNkYPlw3S
kyVsnphgpEwNXtV/ZZFlNexObu70xgGR8+zEnQukDTeDxnxYwpzevS8HlCUuC1Su
iVffQiqdDj3RGE4WLB/NeUbh5VryCkf1EpuSodHnx5FyOw5986llIwlvSNC1WU3B
UNYvT7GU7BbPzrQ46Ru/JZO6CtVOFY+xtxtAsZdJaQRPfnmseJXg+UENDgOdAzN0
emdX3xrw5U+/c5cvXVeYk1Fhsr2luLtieGEZW5BiYZf219dV6LLB+2ALMWOlSJL/
VWwXVrHwoxjyXC5ebjpj
=9iKW
-----END PGP SIGNATURE-----
Merge tag 'dm-3.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper changes for 3.4 from Alasdair Kergon:
- Update thin provisioning to support read-only external snapshot
origins and discards.
- A new target, dm verity, for device content validation.
- Mark dm uevent and dm raid as no-longer-experimental.
- Miscellaneous other fixes and clean-ups.
* tag 'dm-3.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (27 commits)
dm: add verity target
dm bufio: prefetch
dm thin: add pool target flags to control discard
dm thin: support discards
dm thin: prepare to support discard
dm thin: use dm_target_offset
dm thin: support read only external snapshot origins
dm thin: relax hard limit on the maximum size of a metadata device
dm persistent data: remove space map ref_count entries if redundant
dm thin: commit outstanding data every second
dm: reject trailing characters in sccanf input
dm raid: handle failed devices during start up
dm thin metadata: pass correct space map to dm_sm_root_size
dm persistent data: remove redundant value_size arg from value_ptr
dm mpath: detect invalid map_context
dm: clear bi_end_io on remapping failure
dm table: simplify call to free_devices
dm thin: correct comments
dm raid: no longer experimental
dm uevent: no longer experimental
...
This branch contains patches from Mike Turquette adding a common clock
framework to be shared across platforms. This is part of the work towards
building a common zImage for several ARM platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9jfA
-----END PGP SIGNATURE-----
Merge tag 'common-clk-api' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "drivers/clk: common clock framework" from Olof Johansson:
"This branch contains patches from Mike Turquette adding a common clock
framework to be shared across platforms. This is part of the work
towards building a common zImage for several ARM platforms."
* tag 'common-clk-api' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clk: make CONFIG_COMMON_CLK invisible
clk: basic clock hardware types
clk: introduce the common clock framework
Documentation: common clk API
This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a number of
on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wiKV
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More device tree support updates" from Olof Johansson:
"This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a
number of on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device
tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing"
Manually merge arch/arm/mach-ux500/Kconfig due to MACH_U8500 rename, and
drivers/usb/gadget/at91_udc.c due to header file include cleanups.
Also do an "evil merge" for the MACH_U8500 config option rename that the
affected RMI4 touchscreen driver in staging. It's called MACH_MOP500
now, and it was missed during previous merges.
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: SPEAr600: Add device-tree support to SPEAr600 boards
ARM: ux500: Provide local timer support for Device Tree
ARM: ux500: Enable PL022 SSP Controller in Device Tree
ARM: ux500: Enable PL310 Level 2 Cache Controller in Device Tree
ARM: ux500: Enable PL011 AMBA UART Controller for Device Tree
ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device Tree
ARM: ux500: db8500: list most devices in the snowball device tree
ARM: ux500: split dts file for snowball into generic part
ARM: ux500: combine the board init functions for DT boot
ARM: ux500: Initial Device Tree support for Snowball
ARM: ux500: CONFIG: Enable Device Tree support for future endeavours
ARM: kirkwood: use devicetree for rtc-mv
ARM: kirkwood: rtc-mv devicetree bindings
ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
ARM: kirkwood: fdt: facilitate new boards during fdt migration
ARM: kirkwood: fdt: absorb kirkwood_init()
ARM: kirkwood: fdt: use mrvl ticker symbol
ARM: orion: wdt: use resource vice direct access
ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
ARM: orion: spi: remove enable_clock_fix which is not used
...
This device-mapper target creates a read-only device that transparently
validates the data on one underlying device against a pre-generated tree
of cryptographic checksums stored on a second device.
Two checksum device formats are supported: version 0 which is already
shipping in Chromium OS and version 1 which incorporates some
improvements.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Elly Jones <ellyjones@chromium.org>
Cc: Milan Broz <mbroz@redhat.com>
Cc: Olof Johansson <olofj@chromium.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add dm thin target arguments to control discard support.
ignore_discard: Disables discard support
no_discard_passdown: Don't pass discards down to the underlying data
device, but just remove the mapping within the thin provisioning target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support the use of an external _read only_ device as an origin for a thin
device.
Any read to an unprovisioned area of the thin device will be passed
through to the origin. Writes trigger allocation of new blocks as
usual.
One possible use case for this would be VM hosts that want to run
guests on thinly-provisioned volumes but have the base image on another
device (possibly shared between many VMs).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The thin metadata format can only make use of a device that is <=
THIN_METADATA_MAX_SECTORS (currently 15.9375 GB). Therefore, there is no
practical benefit to using a larger device.
However, it may be that other factors impose a certain granularity for
the space that is allocated to a device (E.g. lvm2 can impose a coarse
granularity through the use of large, >= 1 GB, physical extents).
Rather than reject a larger metadata device, during thin-pool device
construction, switch to allowing it but issue a warning if a device
larger than THIN_METADATA_MAX_SECTORS_WARNING (16 GB) is
provided. Any space over 15.9375 GB will not be used.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove documentation for unimplemented 'trim' message.
I'd planned a 'trim' target message for shrinking thin devices, but
this is better handled via the discard ioctl.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Describe attributes provided by device-mapper in /sys/block.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The changes to export dirty_writeback_interval are from Artem's s_dirt
cleanup patch series. The same is true of the change to remove the
s_dirt helper functions which never got used by anyone in-tree. I've
run these changes by Al Viro, and am carrying them so that Artem can
more easily fix up the rest of the file systems during the next merge
window. (Originally we had hopped to remove the use of s_dirt from
ext4 during this merge window, but his patches had some bugs, so I
ultimately ended dropping them from the ext4 tree.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=+9zk
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates for 3.4 from Ted Ts'o:
"Ext4 commits for 3.3 merge window; mostly cleanups and bug fixes
The changes to export dirty_writeback_interval are from Artem's s_dirt
cleanup patch series. The same is true of the change to remove the
s_dirt helper functions which never got used by anyone in-tree. I've
run these changes by Al Viro, and am carrying them so that Artem can
more easily fix up the rest of the file systems during the next merge
window. (Originally we had hopped to remove the use of s_dirt from
ext4 during this merge window, but his patches had some bugs, so I
ultimately ended dropping them from the ext4 tree.)"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (66 commits)
vfs: remove unused superblock helpers
mm: export dirty_writeback_interval
ext4: remove useless s_dirt assignment
ext4: write superblock only once on unmount
ext4: do not mark superblock as dirty unnecessarily
ext4: correct ext4_punch_hole return codes
ext4: remove restrictive checks for EOFBLOCKS_FL
ext4: always set then trimmed blocks count into len
ext4: fix trimmed block count accunting
ext4: fix start and len arguments handling in ext4_trim_fs()
ext4: update s_free_{inodes,blocks}_count during online resize
ext4: change some printk() calls to use ext4_msg() instead
ext4: avoid output message interleaving in ext4_error_<foo>()
ext4: remove trailing newlines from ext4_msg() and ext4_error() messages
ext4: add no_printk argument validation, fix fallout
ext4: remove redundant "EXT4-fs: " from uses of ext4_msg
ext4: give more helpful error message in ext4_ext_rm_leaf()
ext4: remove unused code from ext4_ext_map_blocks()
ext4: rewrite punch hole to use ext4_ext_remove_space()
jbd2: cleanup journal tail after transaction commit
...
DMA_ATTR_NON_CONSISTENT lets the platform to choose to return either
consistent or non-consistent memory as it sees fit. By using this API,
you are guaranteeing to the platform that you have all the correct and
necessary sync points for this memory in the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
DMA_ATTR_WRITE_COMBINE specifies that writes to the mapping may be
buffered to improve performance. It will be used by the replacement for
ARM/ARV32 specific dma_alloc_writecombine() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Change "reg" to "anatop-reg-offset" due to there is a warning of handling no
size field in reg.
This patch also adds the missing device-tree binding documentation.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch updates Jonathan Woithe's contact details across the kernel tree.
Signed-off-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fMC+
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: device tree work" from Arnd Bergmann:
"Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ASoC: DT: Add digital microphone binding to PAZ00 board.
ARM: dt: Add ARM PMU to tegra*.dtsi
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
This new subsystem provides a common way to talk to secondary processors
on an SoC, e.g. a DSP, GPU or service processor, using virtio as the
transport. In the long run, it should replace a few dozen vendor
specific ways to do the same thing, which all never made it into the
upstream kernel. There is a broad agreement that rpmsg is the way to
go here and several vendors have started working on replacing their
own subsystems.
Two branches each add one virtio protocol number. Fortunately the
numbers were agreed upon in advance, so there are only context changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SC55
-----END PGP SIGNATURE-----
Merge tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "remoteproc/rpmsg: new subsystem" from Arnd Bergmann:
"This new subsystem provides a common way to talk to secondary
processors on an SoC, e.g. a DSP, GPU or service processor, using
virtio as the transport. In the long run, it should replace a few
dozen vendor specific ways to do the same thing, which all never made
it into the upstream kernel. There is a broad agreement that rpmsg is
the way to go here and several vendors have started working on
replacing their own subsystems.
Two branches each add one virtio protocol number. Fortunately the
numbers were agreed upon in advance, so there are only context
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial protocol number conflict due to the mentioned additions
next to each other.
* tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
remoteproc: cleanup resource table parsing paths
remoteproc: remove the hardcoded vring alignment
remoteproc/omap: remove the mbox_callback limitation
remoteproc: remove the single rpmsg vdev limitation
remoteproc: safer boot/shutdown order
remoteproc: remoteproc_rpmsg -> remoteproc_virtio
remoteproc: resource table overhaul
rpmsg: fix build warning when dma_addr_t is 64-bit
rpmsg: fix published buffer length in rpmsg_recv_done
rpmsg: validate incoming message length before propagating
rpmsg: fix name service endpoint leak
remoteproc/omap: two Kconfig fixes
remoteproc: make sure we're parsing a 32bit firmware
remoteproc: s/big switch/lookup table/
remoteproc: bail out if firmware has different endianess
remoteproc: don't use virtio's weak barriers
rpmsg: rename virtqueue_add_buf_gfp to virtqueue_add_buf
rpmsg: depend on EXPERIMENTAL
remoteproc: depend on EXPERIMENTAL
rpmsg: add Kconfig menu
...
Conflicts:
include/linux/virtio_ids.h
These are split out from the generic soc and driver updates because
there was a lot of conflicting work by multiple people. Marc Zyngier
worked on simplifying the "localtimer" interfaces, and some of the
platforms are touching the same code as they move to device tree
based booting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=z4Mj
-----END PGP SIGNATURE-----
Merge tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: timer cleanup work" from Arnd Bergmann:
"These are split out from the generic soc and driver updates because
there was a lot of conflicting work by multiple people. Marc Zyngier
worked on simplifying the "localtimer" interfaces, and some of the
platforms are touching the same code as they move to device tree based
booting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
ARM: tegra: select USB_ULPI if USB is selected
arm/tegra: pcie: fix return value of function
ARM: ux500: fix compilation after local timer rework
ARM: shmobile: remove additional __io() macro use
ARM: local timers: make the runtime registration interface mandatory
ARM: local timers: convert MSM to runtime registration interface
ARM: local timers: convert exynos to runtime registration interface
ARM: smp_twd: remove old local timer interface
ARM: imx6q: convert to twd_local_timer_register() interface
ARM: highbank: convert to twd_local_timer_register() interface
ARM: ux500: convert to twd_local_timer_register() interface
ARM: shmobile: convert to twd_local_timer_register() interface
ARM: tegra: convert to twd_local_timer_register() interface
ARM: plat-versatile: convert to twd_local_timer_register() interface
ARM: OMAP4: convert to twd_local_timer_register() interface
ARM: smp_twd: add device tree support
ARM: smp_twd: add runtime registration support
ARM: local timers: introduce a new registration interface
ARM: smp_twd: make local_timer_stop a symbol instead of a #define
ARM: mach-shmobile: default to no earlytimer
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
Add a debugfs interface for sending commands to the OLPC
Embedded Controller (EC) and reading the responses. The EC
provides functionality for machine identification, battery and
AC control, wakeup control, etc.
Having a debugfs interface available is useful for EC
development and debugging.
Based on code by Paul Fox (who also approves of the end result).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Paul Fox <pgf@laptop.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andres Salomon <dilinger@queued.net>
Link: http://lkml.kernel.org/r/20120327150740.667D09D401E@zog.reactivated.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds support for WDIOC_GETTIMELEFT IOCTL in watchdog core. So, there
is another function pointer added to struct watchdog_ops, which can be passed by
drivers to support this IOCTL.
Related documentation is updated too.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When a set_timeout operation succeeds this does not necessarily mean that
the exact timeout requested has been achieved, because the watchdog does not
necessarily have a 1 second resolution. So rather then have the core set
the timeout member of the watchdog_device struct to the exact requested
value, instead the driver should set it to the actually achieved timeout value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The 00-index file in the watchdog directory is, like many others,
outdated (conversion-howto is missing) and doesn't contain worthwhile
additional information. As it seems to be a maintenance burden without
much gain, simply remove it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Define dt bindings for the ti-omap-hsmmc, and adapt the driver to extract
data (which was earlier passed as platform_data) from device tree.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* poll: (5970 commits)
poll: add poll_requested_events() and poll_does_not_wait() functions
crc32: select an algorithm via Kconfig
crc32: add self-test code for crc32c
crypto: crc32c should use library implementation
crc32: bolt on crc32c
crc32: add note about this patchset to crc32.c
crc32: optimize loop counter for x86
crc32: add slice-by-8 algorithm to existing code
crc32: make CRC_*_BITS definition correspond to actual bit counts
crc32: fix mixing of endian-specific types
crc32: miscellaneous cleanups
crc32: simplify unit test code
crc32: move long comment about crc32 fundamentals to Documentation/
crc32: remove two instances of trailing whitespaces
checkpatch: check for quoted strings broken across lines
checkpatch: whitespace - add/remove blank lines
checkpatch: warn on use of yield()
checkpatch: add --strict tests for braces, comments and casts
checkpatch: add [] to type extensions
checkpatch: high precedence operators do not require additional parentheses in #defines
...
The st tape driver recently added the MTWEOFI ioctl, which writes
a tape filemark (EOF), like the MTWEOF ioctl, except that MTWEOFI
returns immediately. This makes certain applications, like backup
software, run much more quickly on buffered tape drives.
Since legacy applications do not know about this new MTWEOFI ioctl,
this patch adds a new ioctl option that tells the st driver to return
immediately when writing an EOF (i.e. a filemark). This new flag
is much like the existing flag that tells the st driver to perform
writes (and certain other IOs) immediately, but this new flag only
applies to writing EOFs.
This new feature is controlled via the MTSETDRVBUFFER ioctl, using
the newly-defined MT_ST_NOWAIT_EOF flag.
Use of this new feature is displayed via the sysfs tape "options"
attribute.
The st documentation was updated to mention this new flag, as well
as the problems that can occur from using it.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for Universal Flash Storage(UFS)
host controllers. The UFS host controller driver
includes host controller initialization method.
The Initialization process involves following steps:
- Initiate UFS Host Controller initialization process by writing
to Host controller enable register
- Configure UFS Host controller registers with host memory space
datastructure offsets.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
- Enable required interrupts
- Configure interrupt aggregation
[jejb: fix warnings in 32 bit compile]
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@linaro.org>
Reviewed-by: Vishak G <vishak.g@samsung.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support to configure the FSMC NAND driver (used amongst
others on SPEAr platforms) via device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the SMBus controller device IDs for the Intel Lynx Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow both device tree (preferred) and platform data-based driver
instantiation.
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Mimic the client side by providing a module parameter that turns off
idmapping in the auth_sys case, for backwards compatibility with NFSv2
and NFSv3.
Unlike in the client case, we don't have any way to negotiate, since the
client can return an error to us if it doesn't like the id that we
return to it in (for example) a getattr call.
However, it has always been possible for servers to return numeric id's,
and as far as we're aware clients have always been able to handle them.
Also, in the auth_sys case clients already need to have numeric id's the
same between client and server.
Therefore we believe it's safe to default this to on; but the module
parameter is available to return to previous behavior if this proves to
be a problem in some unexpected setup.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Otherwise subsystems will get this wrong and end up with a second
export ioctl with the flag and O_CLOEXEC support added.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
v2: Fix spelling issues noticed by Rob Clark.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Sometimes we need to test a kernel of same version with code or config
option changes.
We already have sysctl to disable module load, but add a kernel
parameter will be more convenient.
Since modules_disabled is int, so here use bint type in core_param.
TODO: make sysctl accept bool and change modules_disabled to bool
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The pxa regulator branch removes the bq24022 driver, while a lot of
other regulator drivers got added in the regulator tree. This
resolves the trivial conflicts by merging in the regulator patches
that are already merged into v3.4.
Conflicts:
drivers/regulator/Kconfig
drivers/regulator/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=78St
-----END PGP SIGNATURE-----
Merge tag 'ia64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull miscellaneous Itanium patches from Tony Luck.
The conflicts in arch/ia64/hp/sim/simserial.c were due to patches to
simserial that had alredy been included (with lots of further cleanups)
in the serial tree.
* tag 'ia64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
Documentation/kernel-parameters: remove inttest parameter
[IA64] Fix ISA IRQ trigger model and polarity setting
[IA64] Fix a couple of warnings for EXPORT_SYMBOL
[IA64] Check return from device_register() in cx_device_register()
[IA64] Fix warning from machine_kexec.c
[IA64] simserial, bail out when request_irq fails
[IA64] hpsim, initialize chip for assigned irqs
[IA64] simserial, include some headers
[IA64] hpsim, fix SAL handling in fw-emu
[IA64] genirq fixup for SGI/SN
[IA64] disable interrupts when exiting from ia64_mca_cmc_int_handler()
Merge second batch of patches from Andrew Morton:
- various misc things
- core kernel changes to prctl, exit, exec, init, etc.
- kernel/watchdog.c updates
- get_maintainer
- MAINTAINERS
- the backlight driver queue
- core bitops code cleanups
- the led driver queue
- some core prio_tree work
- checkpatch udpates
- largeish crc32 update
- a new poll() feature for the v4l guys
- the rtc driver queue
- fatfs
- ptrace
- signals
- kmod/usermodehelper updates
- coredump
- procfs updates
* emailed from Andrew Morton <akpm@linux-foundation.org>: (141 commits)
seq_file: add seq_set_overflow(), seq_overflow()
proc-ns: use d_set_d_op() API to set dentry ops in proc_ns_instantiate().
procfs: speed up /proc/pid/stat, statm
procfs: add num_to_str() to speed up /proc/stat
proc: speed up /proc/stat handling
fs/proc/kcore.c: make get_sparsemem_vmemmap_info() static
coredump: add VM_NODUMP, MADV_NODUMP, MADV_CLEAR_NODUMP
coredump: remove VM_ALWAYSDUMP flag
kmod: make __request_module() killable
kmod: introduce call_modprobe() helper
usermodehelper: ____call_usermodehelper() doesn't need do_exit()
usermodehelper: kill umh_wait, renumber UMH_* constants
usermodehelper: implement UMH_KILLABLE
usermodehelper: introduce umh_complete(sub_info)
usermodehelper: use UMH_WAIT_PROC consistently
signal: zap_pid_ns_processes: s/SEND_SIG_NOINFO/SEND_SIG_FORCED/
signal: oom_kill_task: use SEND_SIG_FORCED instead of force_sig()
signal: cosmetic, s/from_ancestor_ns/force/ in prepare_signal() paths
signal: give SEND_SIG_FORCED more power to beat SIGNAL_UNKILLABLE
Hexagon: use set_current_blocked() and block_sigmask()
...
Move a long comment from lib/crc32.c to Documentation/crc32.txt where it
will more likely get read.
Edited the resulting document to add an explanation of the slicing-by-n
algorithm.
[djwong@us.ibm.com: minor changelog tweaks]
[akpm@linux-foundation.org: fix typo, per George]
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Bob Pearson <rpearson@systemfabricworks.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lp5521 has autonomous operation mode without external control.
Using lp5521_platform_data, various led patterns can be configurable.
For supporting this feature, new functions and device attribute are
added.
Structure of lp5521_led_pattern: 3 channels are supported - red, green
and blue. Pattern(s) of each channel and numbers of pattern(s) are
defined in the pla= tform data. Pattern data are hexa codes which
include pattern commands such like set pwm, wait, ramp up/down, branch
and so on.
Pattern mode functions:
* lp5521_clear_program_memory
Before running new led pattern, program memory should be cleared.
* lp5521_write_program_memory
Pattern data updated in the program memory via the i2c.
* lp5521_get_pattern
Get pattern from predefined in the platform data.
* lp5521_run_led_pattern
Stop current pattern or run new pattern.
Transition time is required between different operation mode.
Device attribute - 'led_pattern': To load specific led pattern, new device
attribute is added.
When the lp5521 driver is unloaded, stop current led pattern mode.
Documentation updated : description about how to define the led patterns
and example.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The value of CONFIG register(Addr 08h) is configurable. For supporting
this feature, update_config is added in the platform data. If
'update_config' is not defined, the default value is 'LP5521_PWRSAVE_EN |
LP5521_CP_MODE_AUTO | LP5521_R_TO_BATT'.
To define CONFIG register in the platform data, the bit definitions were
mo= ved to the header file.
Documentation updated : description about 'update_config' and example.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of each led channel can be configurable. For the compatibility,
the name is set to default value(xx:channelN) when 'name' is not defined.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
THis driver supports TI LP8550/LP8551/LP8552/LP8553/LP8556 backlight
devices.
The brightness can be controlled by the I2C or PWM input. The lp855x
driver provides both modes. For the PWM control, pwm-specific functions
can be defined in the platform data. And some information can be read
via the sysfs(lp855x device attributes).
For details, please refer to Documentation/backlight/lp855x-driver.txt.
[axel.lin@gmail.com: add missing mutex_unlock in lp855x_read_byte() error path]
[axel.lin@gmail.com: check platform data in lp855x_probe()]
[axel.lin@gmail.com: small cleanups]
[dan.carpenter@oracle.com: silence a compiler warning]
[axel.lin@gmail.com: use id->driver_data to differentiate lp855x chips]
[akpm@linux-foundation.org: simplify boolean return expression]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull media updates from Mauro Carvalho Chehab:
- V4L2 API additions to better support JPEG compression control
- media API additions to properly support MPEG decoders
- V4L2 API additions for image crop/scaling
- a few other V4L2 API DocBook fixes/improvements
- two new DVB frontend drivers: m88rs2000 and rtl2830
- two new DVB drivers: az6007 and rtl28xxu
- a framework for ISA drivers, that removed lots of common code found
at the ISA radio drivers
- a new FM transmitter driver (radio-keene)
- a GPIO-based IR receiver driver
- a new sensor driver: mt9m032
- some new video drivers: adv7183, blackfin, mx2_emmaprp, sii9234_drv,
vs6624
- several new board additions, driver fixes, improvements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (295 commits)
[media] update CARDLIST.em28xx
[media] partially reverts changeset fa5527c
[media] stb0899: fix the limits for signal strength values
[media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
[media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
[media] -EINVAL -> -ENOTTY
[media] gspca - sn9c20x: Cleanup source
[media] gspca - sn9c20x: Simplify register write for capture start/stop
[media] gspca - sn9c20x: Add automatic JPEG compression mechanism
[media] gspca - sn9c20x: Greater delay in case of sensor no response
[media] gspca - sn9c20x: Optimize the code of write sequences
[media] gspca - sn9c20x: Add the JPEG compression quality control
[media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
[media] gspca - sn9c20x: Propagate USB errors to higher level
[media] gspca - sn9c20x: Use the new video control mechanism
[media] gspca - sn9c20x: Fix loss of frame start
[media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
[media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
[media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
[media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
...
Pull hwmon updates from Jean Delvare:
"We have support for the MCP3021, MC13892 and GMT G781, automatic fan
speed control for LM63/LM64 chips, and a few clean-ups."
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Add MCP3021 ADC driver
hwmon: (mc13783-adc) Add support for the MC13892 PMIC
hwmon: (mc13783-adc) Remove space before tab
hwmon: (lm63) Let the user adjust the lookup table
hwmon: (lm63) Make fan speed control strategy changeable
hwmon: (lm63) Reorganize the code
hwmon: (lm90) Restore original configuration if probe function fails
hwmon: (lm90) Add support for GMT G781
hwmon: (lm90) Fix multi-line comments
hwmon: (w83795) Fix multi-line comments
hwmon: (w83795) Unconditionally support manual fan speed control
hwmon: (fam15h_power) Increase output resolution
hwmon: (fam15h_power) Correct sign extension of running_avg_capture
Pull i2c embedded updates from Wolfram Sang:
"Nothing special from i2c-embedded for this merge window. Two new
drivers, minor feature additions, bugfixes, cleanups.
All patches have been in linux-next for some time, too."
* 'i2c-embedded/for-3.4' of git://git.pengutronix.de/git/wsa/linux:
i2c-eg20t: Remove write-only variables
i2c-eg20t: Rework pch_i2c_wait_for_bus_idle to reduce wait time
i2c-s3c2410: Add stub runtime power management
i2c-s3c2410: Convert to devm_kzalloc()
i2c: add CSR SiRFprimaII on-chip I2C controllers driver
i2c: tegra: Remove unnecessary write to INT_STATUS
i2c: imx: fix imx driver to work though signal is pending
i2c: designware: dw_i2c_init_driver as subsys initcall
misc: at24: describe platform_data with kernel_doc
i2c: Move I2C_EG20T option to the right place.
i2c: Support for Netlogic XLR/XLS I2C controller.
i2c: mpc: Add support for SMBUS_READ_BLOCK_DATA
i2c: versatile: Add Device Tree support
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
- Fix KDB keyboard repeat scan codes and leaked keyboard events
- Fix kernel crash with kdb_printf() for users who compile new kdb_printf()'s
in early code
- Return all segment registers to gdb on x86_64
Features:
- KDB/KGDB hook the reboot notifier and end user can control if it stops,
detaches or does nothing (updated docs as well)
- Notify users who use CONFIG_DEBUG_RODATA to use hw breakpoints
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPbJ17AAoJEIciOldedpOjQeIP/AkUxQFJ7O4aLrLYHl62EHnh
spkgkd+nBzIzcKyV73alkrVBaR2WE2822aAPQmAPBP8/X283DZJJjqgDCUNVI1Mf
CIZ7g8AQHRnS+bAZmof5Jss4malZn4byLvG/cfpOivrsye+4A8MdrAKKM3pYWNVy
4xABkcEknVEEamdNEhHrcPd+xehretfw7+9mmU8hfjqHb/5cXFB7JwDcf4tF7ozT
MDyN4xKtOn1W/ftQl0t6izksCUuPyqKzIfUyAy0j6AwTgsEavXu56S52T1UoB2ZI
JcwLn/ZpN4eGCWVodY04R3jzaMtKFb6ImY40wsb5wl3CU3Ecy5syMU6z4fg3cvjH
/KE6xWF61j4yiE5lzjeJVtKyxwalthzrr56qU2uEwrsEVmo3SOnW9sm0cwouqa7j
/TAMlhZuGgbZGesFwdaUKI5OLGoki+pRQ0Gaq3TsbZwpPC5Bimkq0bIvruruKJCP
QWVkEvb5TZgxCFS3AvniePOm7Hc2wD9zXB3OfN3o91pCom0ryDBIthcLlwhVeNCo
Jd67pnJJNVULPF/1qVicZihKHxvG3DUb4E9pUcbgJplBke+isi+3eHOvnQrYFjIG
iCamE9qvVbsQm/OFV8MOJ5mfPs9R+nb/jNzTO8JDmBc8AL7nRDV3AFGjW68x/KWT
ERcqNEGJ4QuVAxfejq76
=SXu9
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB updates from Jason Wessel:
"Fixes:
- Fix KDB keyboard repeat scan codes and leaked keyboard events
- Fix kernel crash with kdb_printf() for users who compile new
kdb_printf()'s in early code
- Return all segment registers to gdb on x86_64
Features:
- KDB/KGDB hook the reboot notifier and end user can control if it
stops, detaches or does nothing (updated docs as well)
- Notify users who use CONFIG_DEBUG_RODATA to use hw breakpoints"
* tag 'for_linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: Add message about CONFIG_DEBUG_RODATA on failure to install breakpoint
kdb: Avoid using dbg_io_ops until it is initialized
kgdb,debug_core: add the ability to control the reboot notifier
KDB: Fix usability issues relating to the 'enter' key.
kgdb,debug-core,gdbstub: Hook the reboot notifier for debugger detach
kgdb: Respect that flush op is optional
kgdb: x86: Return all segment registers also in 64-bit mode
New features include:
- Add NFS client support for containers.
This should enable most of the necessary functionality, including
lockd support, and support for rpc.statd, NFSv4 idmapper and
RPCSEC_GSS upcalls into the correct network namespace from
which the mount system call was issued.
- NFSv4 idmapper scalability improvements
Base the idmapper cache on the keyring interface to allow concurrent
access to idmapper entries. Start the process of migrating users from
the single-threaded daemon-based approach to the multi-threaded
request-key based approach.
- NFSv4.1 implementation id.
Allows the NFSv4.1 client and server to mutually identify each other
for logging and debugging purposes.
- Support the 'vers=4.1' mount option for mounting NFSv4.1 instead of
having to use the more counterintuitive 'vers=4,minorversion=1'.
- SUNRPC tracepoints.
Start the process of adding tracepoints in order to improve debugging
of the RPC layer.
- pNFS object layout support for autologin.
Important bugfixes include:
- Fix a bug in rpc_wake_up/rpc_wake_up_status that caused them to fail
to wake up all tasks when applied to priority waitqueues.
- Ensure that we handle read delegations correctly, when we try to
truncate a file.
- A number of fixes for NFSv4 state manager loops (mostly to do with
delegation recovery).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LuHE
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.4-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates for Linux 3.4 from Trond Myklebust:
"New features include:
- Add NFS client support for containers.
This should enable most of the necessary functionality, including
lockd support, and support for rpc.statd, NFSv4 idmapper and
RPCSEC_GSS upcalls into the correct network namespace from which
the mount system call was issued.
- NFSv4 idmapper scalability improvements
Base the idmapper cache on the keyring interface to allow
concurrent access to idmapper entries. Start the process of
migrating users from the single-threaded daemon-based approach to
the multi-threaded request-key based approach.
- NFSv4.1 implementation id.
Allows the NFSv4.1 client and server to mutually identify each
other for logging and debugging purposes.
- Support the 'vers=4.1' mount option for mounting NFSv4.1 instead of
having to use the more counterintuitive 'vers=4,minorversion=1'.
- SUNRPC tracepoints.
Start the process of adding tracepoints in order to improve
debugging of the RPC layer.
- pNFS object layout support for autologin.
Important bugfixes include:
- Fix a bug in rpc_wake_up/rpc_wake_up_status that caused them to
fail to wake up all tasks when applied to priority waitqueues.
- Ensure that we handle read delegations correctly, when we try to
truncate a file.
- A number of fixes for NFSv4 state manager loops (mostly to do with
delegation recovery)."
* tag 'nfs-for-3.4-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (224 commits)
NFS: fix sb->s_id in nfs debug prints
xprtrdma: Remove assumption that each segment is <= PAGE_SIZE
xprtrdma: The transport should not bug-check when a dup reply is received
pnfs-obj: autologin: Add support for protocol autologin
NFS: Remove nfs4_setup_sequence from generic rename code
NFS: Remove nfs4_setup_sequence from generic unlink code
NFS: Remove nfs4_setup_sequence from generic read code
NFS: Remove nfs4_setup_sequence from generic write code
NFS: Fix more NFS debug related build warnings
SUNRPC/LOCKD: Fix build warnings when CONFIG_SUNRPC_DEBUG is undefined
nfs: non void functions must return a value
SUNRPC: Kill compiler warning when RPC_DEBUG is unset
SUNRPC/NFS: Add Kbuild dependencies for NFS_DEBUG/RPC_DEBUG
NFS: Use cond_resched_lock() to reduce latencies in the commit scans
NFSv4: It is not safe to dereference lsp->ls_state in release_lockowner
NFS: ncommit count is being double decremented
SUNRPC: We must not use list_for_each_entry_safe() in rpc_wake_up()
Try using machine credentials for RENEW calls
NFSv4.1: Fix a few issues in filelayout_commit_pagelist
NFSv4.1: Clean ups and bugfixes for the pNFS read/writeback/commit code
...
Add I2C driver for MCP3021 that is an ADC chip from Microchip.
The MCP3021 is a successive approximation A/D converter (ADC)
with 10-bit resolution.
The driver export the value of Vin to sysfs, the voltage unit is
mV. Through the sysfs interface, lm-sensors tool can also display
Vin voltage.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on a patch by David Jander that mostly did s/mc13783/mc13xxx/ .
Additionally use dev_get_drvdata instead of to_platform_device +
platform_get_drvdata in mc13783_adc_read (spotted by Jean Delvare).
Cc: David Jander <david.jander@protonic.nl>
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
GMT G781 is a ADM1032-compatible temperature sensor chip.
Add support to the LM90 driver.
Cc: Mike Gorchak <lestat@i.com.ua>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
. Short term fix for 'diff' tool breakage related to perf.data files
with multiple events. From Jiri Olsa
. Cleanup for event id tracepoint reading routine, from Borislav Petkov
. 32-bit compilation fixes from Jiri Olsa
. Event parsing modifier assignment fixes from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=V7d9
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Cleanups and fixes for perf/core:
. Short term fix for 'diff' tool breakage related to perf.data files
with multiple events. From Jiri Olsa
. Cleanup for event id tracepoint reading routine, from Borislav Petkov
. 32-bit compilation fixes from Jiri Olsa
. Event parsing modifier assignment fixes from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Gg7v
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates for v3.4 from Linus Walleij (*):
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
* tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
ARM: u300: configure some pins as an example
pinctrl: support pinconfig on the U300
pinctrl/coh901: use generic pinconf enums and parameters
pinctrl: introduce generic pin config
pinctrl: fix error path in pinconf_map_to_setting()
pinctrl: allow concurrent gpio and mux function ownership of pins
pinctrl: forward-declare struct device
pinctrl: split pincontrol states into its own header
pinctrl: include machine header to core.h
ARM: tegra: Select PINCTRL Kconfig variables
pinctrl: add a driver for NVIDIA Tegra
pinctrl: Show selected function and group in pinmux-pins debugfs
pinctrl: enhance mapping table to support pin config operations
pinctrl: API changes to support multiple states per device
pinctrl: add usecount to pins for muxing
pinctrl: refactor struct pinctrl handling in core.c vs pinmux.c
pinctrl: fix and simplify locking
pinctrl: fix the pin descriptor kerneldoc
pinctrl: assume map table entries can't have a NULL name field
pinctrl: introduce PINCTRL_STATE_DEFAULT, define hogs as that state
...
(*) What is it with all these Linuses these days? There's a Linus at
google too. Some day I will get myself my own broadsword, and run
around screaming "There can be only one".
I used to be _special_ dammit. Snif.
Olof Johansson