The Allwinner A64 SoC is paired with the X-Powers AXP803 PMIC over the
Reduced Serial Bus (RSB).
Enable the driver for this PMIC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[wens@csie.org: Refined commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The pin controller of H5 has three IRQs at the chip's GIC, which
represents three banks of pinctrl IRQs. However, the device tree used to
miss the third IRQ of the pin controller, which makes the PG bank IRQ
not usable.
Add the missing IRQ to the pinctrl node.
Fixes: 4e36de179f ("arm64: allwinner: h5: add Allwinner H5 .dtsi")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
It adds the initial zx296718-pcbox board support with devices like
storage, audio and VGA output enabled.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It enables the I2S sound card support, which is used to drive audio
through aud96p22 codec in case of TV output.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of simple-audio-card, audio-graph-card is recommended for audio
bindings. Let's change to it, so that the HDMI/SPDIF audio card can
align with the new I2S/Codec card which will be added later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We will enable PWM device to control voltage through pwm-regulator
support. So let's add voltage data into OPP table.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The default I2S0 parent clock AUDIO_24M can not be divided into required
sample rate in some cases, for example when 48KHz is needed. Change the
parent clock to AUDIO_99M which works for most sample rates.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It adds VGA device in zx296718.dtsi, so that boards with VGA connector
can enable the support by changing 'status' in board DTS file.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
ls208xa supports another cpu idle state which is pw20 which saves
more power when cpu is idle.
It was implemented through psci firmware.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1088a supports another cpu idle state which is ph20 which saves
more power when cpu is idle.
It was implemented through psci firmware.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When adding the rk3399 sapphire som, two more of the recently removed
num-slots properties of dw-mmc nodes slipped in.
Remove them again.
Fixes: 8164a84cca ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull clockevents fixes from Daniel Lezcano:
" - Fix error check against IS_ERR() instead of NULL for the timer-of code (Dan Carpenter)
- Fix infinite recusion with ftrace for the ARM architected timer (Ding Tianhong)
- Fix the error code return in the em_sti's probe function (Gustavo A. R. Silva)
- Fix Kconfig dependency for the pistachio driver (Matt Redfearn)
- Fix mem frame loop initialization for the ARM architected timer (Matthias Kaehlcke)"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add NAND controller node to LD11 and LD20. Neither of them supports
the CS1 line, so pinctrl is set up for a single CS line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the gmac2phy, make the gmac2phy work on
the rk3328-evb board.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gmac2phy controller of rk3328 is connected to integrated PHY
directly inside, add the node for the integrated PHY support.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the rockchip PHY driver built into the kernel.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add thermal zone and dynamic CPU power coefficients for rk3328
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On platforms with an arch timer erratum workaround, it's possible for
arch_timer_reg_read_stable() to recurse into itself when certain
tracing options are enabled, leading to stack overflows and related
problems.
For example, when PREEMPT_TRACER and FUNCTION_GRAPH_TRACER are
selected, it's possible to trigger this with:
$ mount -t debugfs nodev /sys/kernel/debug/
$ echo function_graph > /sys/kernel/debug/tracing/current_tracer
The problem is that in such cases, preempt_disable() instrumentation
attempts to acquire a timestamp via trace_clock(), resulting in a call
back to arch_timer_reg_read_stable(), and hence recursion.
This patch changes arch_timer_reg_read_stable() to use
preempt_{disable,enable}_notrace(), which avoids this.
This problem is similar to the fixed by upstream commit 96b3d28bf4
("sched/clock: Prevent tracing recursion in sched_clock_cpu()").
Fixes: 6acc71ccac ("arm64: arch_timer: Allows a CPU-specific erratum to only affect a subset of CPUs")
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Commit a1d5ebaf8c ("arm64: big-endian: don't treat code as data when
copying sigret code") moved the 32-bit sigreturn trampoline code from
the aarch32_sigret_code array to kuser32.S. The commit removed the
array definition from signal32.c, but not its declaration in
signal32.h. Remove the leftover declaration.
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Defining the two functions as 'static inline' and exporting them
leads to the interesting case where we can use the interface
from loadable modules, but not from built-in drivers, as shown
in this link failure:
vers/nvdimm/claim.o: In function `nsio_rw_bytes':
claim.c:(.text+0x1b8): undefined reference to `arch_invalidate_pmem'
drivers/nvdimm/pmem.o: In function `pmem_dax_flush':
pmem.c:(.text+0x11c): undefined reference to `arch_wb_cache_pmem'
drivers/nvdimm/pmem.o: In function `pmem_make_request':
pmem.c:(.text+0x5a4): undefined reference to `arch_invalidate_pmem'
pmem.c:(.text+0x650): undefined reference to `arch_invalidate_pmem'
pmem.c:(.text+0x6d4): undefined reference to `arch_invalidate_pmem'
This removes the bogus 'static inline'.
Fixes: d50e071fda ("arm64: Implement pmem API support")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The Cortex-A35 uses some implementation defined perf events.
The Cortex-A35 derives from the Cortex-A53 core, using the same event mapings
based on Cortex-A35 TRM r0p2, section C2.3 - Performance monitoring events
(pages C2-562 to C2-565).
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Cortex-A73 uses some implementation defined perf events.
This patch sets up the necessary mapping for Cortex-A73.
Mappings are based on Cortex-A73 TRM r0p2, section 11.9 Events
(pages 11-457 to 11-460).
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the event mapping code always looks into the PMUv3 events
before any extended mappings, the extended mappings can be reduced to
only those events that are not discoverable through the PMCEID registers.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Last level caches and node events were almost never connected in current
supported cores.
We connect last level caches to the actual last level within the core and
node events are connected to bus accesses.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Generate irqentry and softirqentry text sections without
any Kconfig dependencies. This will add extra sections, but
there should be no performace impact.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David S . Miller <davem@davemloft.net>
Cc: Francis Deslauriers <francis.deslauriers@efficios.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: linux-arch@vger.kernel.org
Cc: linux-cris-kernel@axis.com
Cc: mathieu.desnoyers@efficios.com
Link: http://lkml.kernel.org/r/150172789110.27216.3955739126693102122.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that there are no users of smp_mb__before_spinlock() left, remove
it entirely.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since its inception, our understanding of ACQUIRE, esp. as applied to
spinlocks, has changed somewhat. Also, I wonder if, with a simple
change, we cannot make it provide more.
The problem with the comment is that the STORE done by spin_lock isn't
itself ordered by the ACQUIRE, and therefore a later LOAD can pass over
it and cross with any prior STORE, rendering the default WMB
insufficient (pointed out by Alan).
Now, this is only really a problem on PowerPC and ARM64, both of
which already defined smp_mb__before_spinlock() as a smp_mb().
At the same time, we can get a much stronger construct if we place
that same barrier _inside_ the spin_lock(). In that case we upgrade
the RCpc spinlock to an RCsc. That would make all schedule() calls
fully transitive against one another.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The uaccess_flushcache.c file was inadvertently dropped by the
maintainer in a previous commit. Add it back.
Fixes: 5d7bdeb1ee ("arm64: uaccess: Implement *_flushcache variants")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.
The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.
Fix these issues for proper Wi-Fi support of BPi M64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 board uses an AXP803 PMIC.
Enable the PMIC and its regulators.
As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.
Enable the USB host controller.
The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 96219b0048 ("arm64: allwinner: a64: add device tree for SoPine
with baseboard")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 9702394374 ("arm64: allwinner: pine64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This work implements jiting of BPF_J{LT,LE,SLT,SLE} instructions
with BPF_X/BPF_K variants for the arm64 eBPF JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On UniPhier platform, some DTSI files are shared between arm and arm64.
Recently, inclusion of DT material of different architectures has been
supported by the build system level. Use #include <arm/...>, which
will work without relying on the exact same hierarchy as the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, may_use_simd() can return true if IRQs are disabled. If
the caller goes ahead and calls kernel_neon_begin(), this can
result in use of local_bh_enable() in an unsafe context.
In particular, __efi_fpsimd_begin() may do this when calling EFI as
part of system shutdown.
This patch ensures that callers don't think they can use
kernel_neon_begin() in such a context.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The unwind code sets the sp member of struct stackframe to
'frame pointer + 0x10' unconditionally, without regard for whether
doing so produces a legal value. So let's simply remove it now that
we have stopped using it anyway.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
As it turns out, the unwind code is slightly broken, and probably has
been for a while. The problem is in the dumping of the exception stack,
which is intended to dump the contents of the pt_regs struct at each
level in the call stack where an exception was taken and routed to a
routine marked as __exception (which means its stack frame is right
below the pt_regs struct on the stack).
'Right below the pt_regs struct' is ill defined, though: the unwind
code assigns 'frame pointer + 0x10' to the .sp member of the stackframe
struct at each level, and dump_backtrace() happily dereferences that as
the pt_regs pointer when encountering an __exception routine. However,
the actual size of the stack frame created by this routine (which could
be one of many __exception routines we have in the kernel) is not known,
and so frame.sp is pretty useless to figure out where struct pt_regs
really is.
So it seems the only way to ensure that we can find our struct pt_regs
when walking the stack frames is to put it at a known fixed offset of
the stack frame pointer that is passed to such __exception routines.
The simplest way to do that is to put it inside pt_regs itself, which is
the main change implemented by this patch. As a bonus, doing this allows
us to get rid of a fair amount of cruft related to walking from one stack
to the other, which is especially nice since we intend to introduce yet
another stack for overflow handling once we add support for vmapped
stacks. It also fixes an inconsistency where we only add a stack frame
pointing to ELR_EL1 if we are executing from the IRQ stack but not when
we are executing from the task stack.
To consistly identify exceptions regs even in the presence of exceptions
taken from entry code, we must check whether the next frame was created
by entry text, rather than whether the current frame was crated by
exception text.
To avoid backtracing using PCs that fall in the idmap, or are controlled
by userspace, we must explcitly zero the FP and LR in startup paths, and
must ensure that the frame embedded in pt_regs is zeroed upon entry from
EL0. To avoid these NULL entries showin in the backtrace, unwind_frame()
is updated to avoid them.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[Mark: compare current frame against .entry.text, avoid bogus PCs]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
vDSO VMA address is saved in mm_context for the purpose of using
restorer from vDSO page to return to userspace after signal handling.
In Checkpoint Restore in Userspace (CRIU) project we place vDSO VMA
on restore back to the place where it was on the dump.
With the exception for x86 (where there is API to map vDSO with
arch_prctl()), we move vDSO inherited from CRIU task to restoree
position by mremap().
CRIU does support arm64 architecture, but kernel doesn't update
context.vdso pointer after mremap(). Which results in translation
fault after signal handling on restored application:
https://github.com/xemul/criu/issues/288
Make vDSO code track the VMA address by supplying .mremap() fops
the same way it's done for x86 and arm32 by:
commit b059a453b1 ("x86/vdso: Add mremap hook to vm_special_mapping")
commit 280e87e98c ("ARM: 8683/1: ARM32: Support mremap() for sigpage/vDSO").
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dmitry Safonov <dsafonov@virtuozzo.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Implement the set of copy functions with guarantees of a clean cache
upon completion necessary to support the pmem driver.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a clean-to-point-of-persistence cache maintenance helper, and wire
up the basic architectural support for the pmem driver based on it.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[catalin.marinas@arm.com: move arch_*_pmem() functions to arch/arm64/mm/flush.c]
[catalin.marinas@arm.com: change dmb(sy) to dmb(osh)]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cache clean to PoP is subject to the same access controls as to PoC, so
if we are trapping userspace cache maintenance with SCTLR_EL1.UCI, we
need to be prepared to handle it. To avoid getting into complicated
fights with binutils about ARMv8.2 options, we'll just cheat and use the
raw SYS instruction rather than the 'proper' DC alias.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The ARMv8.2-DCPoP feature introduces persistent memory support to the
architecture, by defining a point of persistence in the memory
hierarchy, and a corresponding cache maintenance operation, DC CVAP.
Expose the support via HWCAP and MRS emulation.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__inval_cache_range() is already the odd one out among our data cache
maintenance routines as the only remaining range-based one; as we're
going to want an invalidation routine to call from C code for the pmem
API, let's tweak the prototype and name to bring it in line with the
clean operations, and to make its relationship with __dma_inv_area()
neatly mirror that of __clean_dcache_area_poc() and __dma_clean_area().
The loop clearing the early page tables gets mildly massaged in the
process for the sake of consistency.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clearly, set_memory_valid() has never been seen in the same room as its
declaration... Whilst the type mismatch is such that kexec probably
wasn't broken in practice, fix it to match the definition as it should.
Fixes: 9b0aa14e31 ("arm64: mm: add set_memory_valid()")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch switches to the stable UART bindings but also add the correct
gate clock to the non-AO UART nodes for GXBB and GXL SoCs.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the smd-edge node for the adsp, to allow SMD communication with the
ADSP.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the SMP2P nodes for the modem.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adding required device node for couple of DWC3 controllers
present on msm8996 chipset to enable High speed and Super
speed USB support.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add required device node for QMP phy based 3-lane PCIe phy
present on msm8996 chipset to enable support for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adding required device node for USB3 QMP phy present on
msm8996 chipset to enable support for the same. This phy
provides super speed usb functionality for dwc3 controller
on msm8996.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adding device node for QUSB2 phy and the required infrastructure
to enable support for the same. This phy is used by dwc3 controller
present on msm8996.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The adv7533 on this board needs a cec clock. Hook it up in the dtsi
to enable CEC for the HDMI transmitters.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Replace the obsolete compatible string for Coresight programmable
replicator with the new one.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Commit ed75d6a969 ("arm64: dts: qcom: Collapse usb support into
one node") breaks host mode support on apq8016-sbc boards. This
is because the mux driver (tc7usb40mu) hasn't been merged.
Without that driver, we can't toggle the GPIO going to the mux to
route out the D+/D- lines to the USB hub that's on the board.
One solution would be to totally revert this change, but that
opens us up to other problems when two USB drivers are operating
the same hardware block at the same time. Let's modify the DT so
that the USB controller is always in host mode and connected to
the hub so that things like USB keyboards and mouses work. This
is the mode that most people prefer anyway with these devices. We
also delete the usb-switch node because the binding was never
accepted upstream.
In the future, we can add muxing support and then update the DT
to support both modes at runtime. Patches to support this are
already on the mailing list.
Fixes: ed75d6a969 ("arm64: dts: qcom: Collapse usb support into one node")
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Rather than continue adding CPU-specific event maps, instead look up by
default in the PMUv3 event map and only fallback to the CPU-specific maps
if either the event isn't described by PMUv3, or it is described but
the PMCEID registers say that it is unsupported by the current CPU.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, when unwinding the call stack, we validate the frame pointer
of each frame against frame.sp, whose value is not clearly defined, and
which makes it more difficult to link stack frames together across
different stacks. It is far better to simply check whether the frame
pointer itself points into a valid stack.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Our IRQ_STACK_PTR() and on_irq_stack() helpers both take a cpu argument,
used to generate a percpu address. In all cases, they are passed
{raw_,}smp_processor_id(), so this parameter is redundant.
Since {raw_,}smp_processor_id() use a percpu variable internally, this
approach means we generate a percpu offset to find the current cpu, then
use this to index an array of percpu offsets, which we then use to find
the current CPU's IRQ stack pointer. Thus, most of the work is
redundant.
Instead, we can consistently use raw_cpu_ptr() to generate the CPU's
irq_stack pointer by simply adding the percpu offset to the irq_stack
address, which is simpler in both respects.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Currently, cpu_switch_to and ret_from_fork both live in .entry.text,
though neither form the critical path for an exception entry.
In subsequent patches, we will require that code in .entry.text is part
of the critical path for exception entry, for which we can assume
certain properties (e.g. the presence of exception regs on the stack).
Neither cpu_switch_to nor ret_from_fork will meet these requirements, so
we must move them out of .entry.text. To ensure that neither are kprobed
after being moved out of .entry.text, we must explicitly blacklist them,
requiring a new NOKPROBE() asm helper.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
In most cases, our exception entry assembly branches to C handlers with
a BL instruction, but in cases where we do not expect to return, we use
B instead.
While this is correct today, it means that backtraces for fatal
exceptions miss the entry assembly (as the LR is stale at the point we
call C code), while non-fatal exceptions have the entry assembly in the
LR. In subsequent patches, we will need the LR to be set in these cases
in order to backtrace reliably.
This patch updates these sites to use a BL, ensuring consistency, and
preparing for backtrace rework. An ASM_BUG() is added after each of
these new BLs, which both catches unexpected returns, and ensures that
the LR value doesn't point to another function label.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Currently. we can only use BUG() from C code, though there are
situations where we would like an equivalent mechanism in assembly code.
This patch refactors our BUG() definition such that it can be used in
either C or assembly, in the form of a new ASM_BUG().
The refactoring requires the removal of escape sequences, such as '\n'
and '\t', but these aren't strictly necessary as we can use ';' to
terminate assembler statements.
The low-level assembly is factored out into <asm/asm-bug.h>, with
<asm/bug.h> retained as the C wrapper.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Currently:
$ perf stat -e cycles:u -e cycles:k true
Performance counter stats for 'true':
2,24,699 cycles:u
<not counted> cycles:k (0.00%)
0.000788087 seconds time elapsed
We can not count more than one cycle counter in one instance,because we
allow to map cycle counter into PMCCNTR_EL0 only. However, if I did not
miss anything then specification do not prohibit to use PMEVCNTR<n>_EL0
for cycle count as well.
Modify the code so that it still prefers to use PMCCNTR_EL0 for cycle
counter, however allow to use PMEVCNTR<n>_EL0 if PMCCNTR_EL0 is already
in use.
After this patch:
$ perf stat -e cycles:u -e cycles:k true
Performance counter stats for 'true':
2,17,310 cycles:u
7,40,009 cycles:k
0.000764149 seconds time elapsed
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This implements the kvm_arch_vcpu_in_kernel() for ARM, and adjusts
the calls to kvm_vcpu_on_spin().
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a vcpu exits due to request a user mode spinlock, then
the spinlock-holder may be preempted in user mode or kernel mode.
(Note that not all architectures trap spin loops in user mode,
only AMD x86 and ARM/ARM64 currently do).
But if a vcpu exits in kernel mode, then the holder must be
preempted in kernel mode, so we should choose a vcpu in kernel mode
as a more likely candidate for the lock holder.
This introduces kvm_arch_vcpu_in_kernel() to decide whether the
vcpu is in kernel-mode when it's preempted. kvm_vcpu_on_spin's
new argument says the same of the spinning VCPU.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds Broadcom SBA-RAID DT nodes for Stingray SoC.
The Stingray SoC has total 32 SBA-RAID FlexRM rings and it has
8 CPUs so we create 8 SBA-RAID instances (one for each CPU).
This way Linux DMAENGINE will have one SBA-RAID DMA device for
each CPU.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have two instances of FlexRM on Stingray. One for SBA RAID
offload engine and another for SPU2 Crypto offload engine.
This patch adds FlexRM mailbox controller DT nodes for Stingray.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add DT nodes for SATA host controllers and SATA PHYs
on Stingray SoC
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have 8 instances of sp804 in Stingray SoC. Let's enable
it in Stingray DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Added MDIO multiplexer iproc DT node for Stingray, which contains
the child nodes of PCIe serdes, RGMII, SATA and USB phy MDIO slaves.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch enables stats for CCN-502 interconnect on Stingray.
Signed-off-by: Velibor Markovski <velibor.markovski@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
may_use_simd() can be invoked from loadable modules and it accesses
kernel_neon_busy. Make sure that the latter is exported.
Fixes: cb84d11e16 ("arm64: neon: Remove support for nested or hardirq kernel-mode NEON")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When receiving unhandled faults from the CPU, description is very sparse.
Adding information about faults decoded from ESR.
Added defines to esr.h corresponding ESR fields. Values are based on ARM
Archtecture Reference Manual (DDI 0487B.a), section D7.2.28 ESR_ELx, Exception
Syndrome Register (ELx) (pages D7-2275 to D7-2280).
New output is of the form:
[ 77.818059] Mem abort info:
[ 77.820826] Exception class = DABT (current EL), IL = 32 bits
[ 77.826706] SET = 0, FnV = 0
[ 77.829742] EA = 0, S1PTW = 0
[ 77.832849] Data abort info:
[ 77.835713] ISV = 0, ISS = 0x00000070
[ 77.839522] CM = 0, WnR = 1
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: fix "%lu" in a pr_alert() call]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The -1 "no syscall" value is written in various ways, shared with
the user ABI in some places, and generally obscure.
This patch attempts to make things a little more consistent and
readable by replacing all these uses with a single #define. A
couple of symbolic helpers are provided to clarify the intent
further.
Because the in-syscall check in do_signal() is changed from >= 0 to
!= NO_SYSCALL by this patch, different behaviour may be observable
if syscallno is set to values less than -1 by a tracer. However,
this is not different from the behaviour that is already observable
if a tracer sets syscallno to a value >= __NR_(compat_)syscalls.
It appears that this can cause spurious syscall restarting, but
that is not a new behaviour either, and does not appear harmful.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The upper 32 bits of the syscallno field in thread_struct are
handled inconsistently, being sometimes zero extended and sometimes
sign-extended. In fact, only the lower 32 bits seem to have any
real significance for the behaviour of the code: it's been OK to
handle the upper bits inconsistently because they don't matter.
Currently, the only place I can find where those bits are
significant is in calling trace_sys_enter(), which may be
unintentional: for example, if a compat tracer attempts to cancel a
syscall by passing -1 to (COMPAT_)PTRACE_SET_SYSCALL at the
syscall-enter-stop, it will be traced as syscall 4294967295
rather than -1 as might be expected (and as occurs for a native
tracer doing the same thing). Elsewhere, reads of syscallno cast
it to an int or truncate it.
There's also a conspicuous amount of code and casting to bodge
around the fact that although semantically an int, syscallno is
stored as a u64.
Let's not pretend any more.
In order to preserve the stp x instruction that stores the syscall
number in entry.S, this patch special-cases the layout of struct
pt_regs for big endian so that the newly 32-bit syscallno field
maps onto the low bits of the stored value. This is not beautiful,
but benchmarking of the getpid syscall on Juno suggests indicates a
minor slowdown if the stp is split into an stp x and stp w.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
clock name of "audio_clkout" is used by Renesas sound driver.
This duplicated naming breaks its clock registering/unregistering.
Especially, when unbind/bind it can't handle clkout correctly.
This patch renames "audio_clkout" to "audio-clkout" to avoid
naming conflict.
Fixes: 8a8f181d2c ("arm64: renesas: salvator-x: use CS2000 as AUDIO_CLK_B")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.
This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the rk3399 sapphire SOM board.
This board works in a combination with the excavator main board.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an mipi node, and also add mipi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
1. add pd node for RK3399 Soc
2. create power domain tree
3. add qos node for domain
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add opp tables for cpu cluster0 and cluster1 by including
rk3399-opp.dtsi.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
aliases node is identical for all boards, thus move it
to the common file ls208xa.dtsi.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJZhNZ2AAoJEED/6hsPKofoKDEH/iIw1pcgdEW2NP/kFtKXSMCK
josdFwGPQMjBGzx6No4tfMCNDOjW2FKYXapN6CASAqMJo5H2krj8VHMVwm0h3lUl
4RdbbkFTdfl/Znp8M39efFheWrjX+L37AltKV7xAgA7n8cO39KV4RReimzSc7aVq
5dDt4k0dbF9/zXHxkGiKEhwaSSbZEEznQQ/09annSoOVe6om5esUrUtnUF5P99uz
IhAsmJbZxE5VmowjT5MjaR1mXSLLNL55HWKvkf3B3ZGnyxQU+3Vz7IGf2Ma2j+jV
IrdXA11NHDY1anDYgDhFlr3rTCPu9CBmTv4O8zsDRlX9TGpr8bBX2dvjRKl7uOo=
=KM80
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
This comes a bit later than I planned, and as a consequence is a larger
than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic Meson,
Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple randconfig
build fixes. This includes making the CONFIG_MTD_XIP option compile again,
which had been broken for many years and probably has not been missed, but
it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards
to work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a2dO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
The crypto code currently relies on kernel_mode_begin_partial() being
available. Until the corresponding crypto patches are merged, define
this macro temporarily, though with different semantics as it cannot be
called in interrupt context.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The bitmask used to define these values produces overflow, as seen by
this compiler warning:
arch/arm64/kernel/head.S:47:8: warning:
integer overflow in preprocessor expression
#elif (PAGE_OFFSET & 0x1fffff) != 0
^~~~~~~~~~~
arch/arm64/include/asm/memory.h:52:46: note:
expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (UL(0xffffffffffffffff) << (VA_BITS -
1))
~~~~~~~~~~~~~~~~~~ ^
It would be preferrable to use GENMASK_ULL() instead, but it's not set
up to be used from assembly (the UL() macro token pastes UL suffixes
when not included in assembly sources).
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Yury Norov <ynorov@caviumnetworks.com>
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Support for kernel-mode NEON to be nested and/or used in hardirq
context adds significant complexity, and the benefits may be
marginal. In practice, kernel-mode NEON is not used in hardirq
context, and is rarely used in softirq context (by certain mac80211
drivers).
This patch implements an arm64 may_use_simd() function to allow
clients to check whether kernel-mode NEON is usable in the current
context, and simplifies kernel_neon_{begin,end}() to handle only
saving of the task FPSIMD state (if any). Without nesting, there
is no other state to save.
The partial fpsimd save/restore functions become redundant as a
result of these changes, so they are removed too.
The save/restore model is changed to operate directly on
task_struct without additional percpu storage. This simplifies the
code and saves a bit of memory, but means that softirqs must now be
disabled when manipulating the task fpsimd state from task context:
correspondingly, preempt_{en,dis}sable() calls are upgraded to
local_bh_{en,dis}able() as appropriate. fpsimd_thread_switch()
already runs with hardirqs disabled and so is already protected
from softirqs.
These changes should make it easier to support kernel-mode NEON in
the presence of the Scalable Vector extension in the future.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to be able to cope with kernel-mode NEON being unavailable
in hardirq/nmi context and non-nestable, we need special handling
for EFI runtime service calls that may be made during an interrupt
that interrupted a kernel_neon_begin()..._end() block. This will
occur if the kernel tries to write diagnostic data to EFI
persistent storage during a panic triggered by an NMI for example.
EFI runtime services specify an ABI that clobbers the FPSIMD state,
rather than being able to use it optionally as an accelerator.
This means that EFI is really a special case and can be handled
specially.
To enable EFI calls from interrupts, this patch creates dedicated
__efi_fpsimd_{begin,end}() helpers solely for this purpose, which
save/restore to a separate percpu buffer if called in a context
where kernel_neon_begin() is not usable.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
__this_cpu_ ops are not used consistently with regard to this_cpu_
ops in a couple of places in fpsimd.c.
Since preemption is explicitly disabled in
fpsimd_restore_current_state() and fpsimd_update_current_state(),
this patch converts this_cpu_ ops in those functions to __this_cpu_
ops. This doesn't save cost on arm64, but benefits from additional
assertions in the core code.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
asm/neon.h doesn't have a header inclusion guard, but it should
have one for consistency with other headers.
This patch adds a suitable guard.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation of modifying the logic that decides whether kernel mode
NEON is allowable, which is required for SVE support, introduce an
implementation of may_use_simd() that reflects the current reality, i.e.,
that SIMD is allowed in any context.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In a system with DBM (dirty bit management) capable agents there is a
possible race between a CPU executing ptep_set_access_flags() (maybe
non-DBM capable) and a hardware update of the dirty state (clearing of
PTE_RDONLY). The scenario:
a) the pte is writable (PTE_WRITE set), clean (PTE_RDONLY set) and old
(PTE_AF clear)
b) ptep_set_access_flags() is called as a result of a read access and it
needs to set the pte to writable, clean and young (PTE_AF set)
c) a DBM-capable agent, as a result of a different write access, is
marking the entry as young (setting PTE_AF) and dirty (clearing
PTE_RDONLY)
The current ptep_set_access_flags() implementation would set the
PTE_RDONLY bit in the resulting value overriding the DBM update and
losing the dirty state.
This patch fixes such race by setting PTE_RDONLY to the most permissive
(lowest value) of the current entry and the new one.
Fixes: 66dbd6e61a ("arm64: Implement ptep_set_access_flags() for hardware AF/DBM")
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Two fixes to correct the EMAC blocks memory region size to match the
datasheet. One that converts raw A83T clock indices to macros from the
clk dt-binding header, completing the A83T sunxi-ng clk driver.
-----BEGIN PGP SIGNATURE-----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=aFvT
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.13" from Chen-Yu Tsai:
Two fixes to correct the EMAC blocks memory region size to match the
datasheet. One that converts raw A83T clock indices to macros from the
clk dt-binding header, completing the A83T sunxi-ng clk driver.
* tag 'sunxi-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
All the fixes are for ARM64 mvebu:
- Fix the RTC interrupt on A7K/A8K which was missed when switching
from GIC to ICU
- Mark the A7K/A8K crypto engine as dma coherent
- Fix the number of GPIO on south bridge on Armada 3700
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWYHbmCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71ZhfAJ9Z9aMBG1xd
vbRYBDdqPdntruTudwCcDtM9jS2nL+207JfeMD0WMs7sDdU=
=XwFM
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.13-2' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fixes for 4.13 (part 2)" from Gregory CLEMENT:
All the fixes are for ARM64 mvebu:
- Fix the RTC interrupt on A7K/A8K which was missed when switching
from GIC to ICU
- Mark the A7K/A8K crypto engine as dma coherent
- Fix the number of GPIO on south bridge on Armada 3700
* tag 'mvebu-fixes-4.13-2' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
arm64: dts: marvell: mark the cp110 crypto engine as dma coherent
arm64: dts: marvell: use ICU for the CP110 slave RTC
- 2 minor DT fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Z5d3
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Pull "Amlogic fixes for v4.13-rc" from Kevin Hilman:
- 2 minor DT fixes
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition
ARM64: dts: meson-gx: use specific compatible for the AO pwms
For the final round, avoid the expanded and padded lookup tables
exported by the generic AES driver. Instead, for encryption, we can
perform byte loads from the same table we used for the inner rounds,
which will still be hot in the caches. For decryption, use the inverse
AES Sbox directly, which is 4x smaller than the inverse lookup table
exported by the generic driver.
This should significantly reduce the Dcache footprint of our code,
which makes the code more robust against timing attacks. It does not
introduce any additional module dependencies, given that we already
rely on the core AES module for the shared key expansion routines.
It also frees up register x18, which is not available as a scratch
register on all platforms, which and so avoiding it improves
shareability of this code.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Implement a NEON fallback for systems that do support NEON but have
no support for the optional 64x64->128 polynomial multiplication
instruction that is part of the ARMv8 Crypto Extensions. It is based
on the paper "Fast Software Polynomial Multiplication on ARM Processors
Using the NEON Engine" by Danilo Camara, Conrado Gouvea, Julio Lopez and
Ricardo Dahab (https://hal.inria.fr/hal-01506572), but has been reworked
extensively for the AArch64 ISA.
On a low-end core such as the Cortex-A53 found in the Raspberry Pi3, the
NEON based implementation is 4x faster than the table based one, and
is time invariant as well, making it less vulnerable to timing attacks.
When combined with the bit-sliced NEON implementation of AES-CTR, the
AES-GCM performance increases by 2x (from 58 to 29 cycles per byte).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, the AES-GCM implementation for arm64 systems that support the
ARMv8 Crypto Extensions is based on the generic GCM module, which combines
the AES-CTR implementation using AES instructions with the PMULL based
GHASH driver. This is suboptimal, given the fact that the input data needs
to be loaded twice, once for the encryption and again for the MAC
calculation.
On Cortex-A57 (r1p2) and other recent cores that implement micro-op fusing
for the AES instructions, AES executes at less than 1 cycle per byte, which
means that any cycles wasted on loading the data twice hurt even more.
So implement a new GCM driver that combines the AES and PMULL instructions
at the block level. This improves performance on Cortex-A57 by ~37% (from
3.5 cpb to 2.6 cpb)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Of the various chaining modes implemented by the bit sliced AES driver,
only CTR is exposed as a synchronous cipher, and requires a fallback in
order to remain usable once we update the kernel mode NEON handling logic
to disallow nested use. So wire up the existing CTR fallback C code.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To accommodate systems that disallow the use of kernel mode NEON in
some circumstances, take the return value of may_use_simd into
account when deciding whether to invoke the C fallback routine.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To accommodate systems that may disallow use of the NEON in kernel mode
in some circumstances, introduce a C fallback for synchronous AES in CTR
mode, and use it if may_use_simd() returns false.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 kernel will shortly disallow nested kernel mode NEON.
So honour this in the ARMv8 Crypto Extensions implementation of
CCM-AES, and fall back to a scalar implementation using the generic
crypto helpers for AES, XOR and incrementing the CTR counter.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 kernel will shortly disallow nested kernel mode NEON, so
add a fallback to scalar code that can be invoked in that case.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to be able to reuse the generic AES code as a fallback for
situations where the NEON may not be used, update the key handling
to match the byte order of the generic code: it stores round keys
as sequences of 32-bit quantities rather than streams of bytes, and
so our code needs to be updated to reflect that.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 kernel will shortly disallow nested kernel mode NEON, so
add a fallback to scalar code that can be invoked in that case.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 kernel will shortly disallow nested kernel mode NEON, so
add a fallback to scalar C code that can be invoked in that case.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 kernel will shortly disallow nested kernel mode NEON, so
add a fallback to scalar C code that can be invoked in that case.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 kernel will shortly disallow nested kernel mode NEON, so
add a fallback to scalar C code that can be invoked in that case.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The arm64 kernel will shortly disallow nested kernel mode NEON, so
add a fallback to scalar C code that can be invoked in that case.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are quite a number of occurrences in the kernel of the pattern
if (dst != src)
memcpy(dst, src, walk.total % AES_BLOCK_SIZE);
crypto_xor(dst, final, walk.total % AES_BLOCK_SIZE);
or
crypto_xor(keystream, src, nbytes);
memcpy(dst, keystream, nbytes);
where crypto_xor() is preceded or followed by a memcpy() invocation
that is only there because crypto_xor() uses its output parameter as
one of the inputs. To avoid having to add new instances of this pattern
in the arm64 code, which will be refactored to implement non-SIMD
fallbacks, add an alternative implementation called crypto_xor_cpy(),
taking separate input and output arguments. This removes the need for
the separate memcpy().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Yet another race with VM destruction plugged
- A set of small vgic fixes
-----BEGIN PGP SIGNATURE-----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=TMR9
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM Fixes for v4.13-rc4
- Yet another race with VM destruction plugged
- A set of small vgic fixes
Tests showed, that under certain conditions, the summary number of jiffies
spent on softirq/idle, which are counted by system statistics can be even
below 10% of expected value, resulting in false load presentation.
The issue was observed on the quad-core Marvell Armada 8k SoC, whose two
10G ports were bound into L2 bridge. Load was controlled by bidirectional
UDP traffic, produced by a packet generator. Under such condition,
the dominant load is softirq. With 100% single CPU occupation or without
any activity (all CPUs 100% idle), total number of jiffies is 10000 (2500
per each core) in 10s interval. Also with other kind of load this was
true.
However below a saturation threshold it was observed, that with CPU which
was occupied almost by softirqs only, the statistic were awkward. See
the mpstat output:
CPU %usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
all 0.00 0.00 0.13 0.00 0.00 0.55 0.00 0.00 0.00 99.32
0 0.00 0.00 0.00 0.00 0.00 23.08 0.00 0.00 0.00 76.92
1 0.00 0.00 0.40 0.00 0.00 0.00 0.00 0.00 0.00 99.60
2 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00
3 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 100.00
Above would mean basically no total load, debug CPU0 occupied in 25%.
Raw statistics, printed every 10s from /proc/stat unveiled a root
cause - summary idle/softirq jiffies on loaded CPU were below 200,
i.e. over 90% samples lost. All problems were gone after enabling
fine granulity IRQ time accounting.
This patch fixes possible wrong statistics processing by enabling
CONFIG_IRQ_TIME_ACCOUNTING for arm64 platfroms, which is by
default done on other architectures, e.g. x86 and arm. Tests
showed no noticeable performance penalty, nor stability impact.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The ESPRESSObin board exposes one of the SDHCI interfaces
via J1 uSD slot. This patch enables it.
Tested-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Zbigniew Bodek <zbodek@gmail.com>
[gregory.clement@free-electrons.com: removed "no-1-8-v"]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the introduction of the CP110 dt files, the sata node was
misplaced. Move it at the right place. Thanks to this, the files are
completely ordered.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Multiple architectures define this as a trivial function, and I'm adding
another one as part of the RISC-V port. Add a __weak version of
pcibios_align_resource() and delete the now-obselete ones in a handful of
ports.
The only functional change should be that a handful of ports used to export
pcibios_fixup_bus(). Only some architectures export this, so I just
dropped it.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Multiple architectures define this as an empty function, and I'm adding
another one as part of the RISC-V port. Add a __weak version of
pcibios_fixup_bus() and delete the now-obselete ones in a handful of
ports.
The only functional change should be that microblaze used to export
pcibios_fixup_bus(). None of the other architectures exports this, so I
just dropped it.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In both the CP110 master and slave description, the node describing
the RTC was at the wrong place when taking into account increasing
register addresses. Interestingly, it was not even at the same (wrong)
place in both files.
This commit adjusts that, making the master and slave descriptions
more aligned.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds an stdout-path to the mcbin device tree. This allows to
use earlycon.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add support for PCIe with the the PCIe reset signal wired up to the
appropriate GPIO pin.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
(excepted the reset part)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The MACCHIATOBin board has a PCA9548 I2C mux for the SFP ports on
CP100 master I2C bus 1. Add the DT description for it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Due to the lack of GPIO support, the USB3 regulator definition was
left unfinished in the MacchiatoBin DT description. Now that GPIO
support is available, this commit adjusts the Device Tree to properly
describe the USB3 regulator.
[gregory.clement@free-electrons.com: use commit log from Thomas]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add pinctrl nodes to describe the CPM I2C0 and CPS SPI1 settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the GPIO interrupts for the CP110.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Espressobin SBC has a USB2 interface available on J8. Let's
enable it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a PMUv3, just like most ARMv8 cores.
Advertise the PMUv3 presence in the device tree, and wire its
interrupt. This allows the perf subsystem to work correctly.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a GIC CPU interface that gets enabled when coupled with a GICv3
interrupt controller, such as the GIC-500 on the this SoC.
Advertise the MMIO ranges provided by the CPUs, which enables
(among other things) GICv2 guests to run under a hypervisor such
as KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The GIC-500 integrated in the Armada-37xx SoCs is compliant with
the GICv3 architecture, and thus provides a maintenance interrupt
that is required for hypervisors to function correctly.
With the interrupt provided in the DT, KVM now works as it should.
Tested on an Espressobin system.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007fed ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since underscores('_') are not allowed in the device tree nodes names,
replace all of them with hyphen('-') in device node names. Note that
underscores are however allowed in labels.
Reported-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Use the new compatible for ATB programmable replicator in Juno.
Cc: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch describes the GPIO lines usage on the Nanopi K2 board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch describes the GPIO lines usage on the Khadas VIM board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: minor whitespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Changing the card voltage on the p200 is not instantaneous, especially
when switching from 3.3v to 1.8v.
I take at least 70ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: ef8d2ffedf ("ARM64: dts: meson-gxbb: add MMC support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In an ideal world, CNTFRQ_EL0 always contains the timer frequency
for the kernel to use. Sadly, we get quite a few broken systems
where the firmware authors cannot be bothered to program that
register on all CPUs, and rely on DT to provide that frequency.
So when trapping CNTFRQ_EL0, make sure to return the actual rate
(as known by the kernel), and not CNTFRQ_EL0.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch updates the dynamic-power-coefficient for big cluster on
rk3399 SoCs.
The dynamic power consumption of the CPU is proportional to the square of
the Voltage (V) and the clock frequency (f). The coefficient is used to
calculate the dynamic power as below -
Pdyn = dynamic-power-coefficient * V^2 * f
Where Voltage is in uV, frequency is in MHz.
As the following is the tested data on rk3399's big cluster.
frequency(MHz) Voltage(V) Current(mA) Dynamic-power-coefficient
24 0.8 15
48 0.8 23 ~417
96 0.8 40 ~443
216 0.8 82 ~438
312 0.8 115 ~430
408 0.8 150 ~455
So the dynamic-power-coefficient average value is about 436.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
BCM2837 is somewhat unusual in that we build its DT on both arm32 and
arm64. Most devices are being run in arm32 mode.
Having the body of the DT for 2837 separate from 2835/6 has been a
source of pain, as we often need to make changes that span both
directories simultaneously (for example, the thermal changes for 4.13,
or anything that changes the name of a node referenced by '&' from
board files). Other changes are made more complicated than they need
to be, such as the SDHOST enabling, because we have to split a single
logical change into a 283[56] half and a 2837 half.
To fix this, make the stub board include file live in arm64 instead of
arm32, and keep all of BCM283x's contents in arm32. From here on, our
changes to DT contents can be submitted through a single tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Place northstar2 into its own subdirectory. This helps as the number
of Broadcom boards grow and we can separate them per SoC.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- Ensure we have a guard page after the kernel image in vmalloc
- Fix incorrect prefetch stride in copy_page
- Ensure irqs are disabled in die()
- Fix for event group validation in QCOM L2 PMU driver
- Fix requesting of PMU IRQs on AMD Seattle
- Minor cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJZey1iAAoJELescNyEwWM0w/0H/1RaHFUSoFUIoL+qFD0eGXcp
hORI0sIHrUlHRONTFYMTyNko7kxELz5aDm6pc87dzBUNoUq3gxhqeEa0zsmwOPsQ
m4iDa7r9xXT+nBITe2auAg6miEMX7Ym448dDrIyKNcRK+2SyZoFqS0vr8UVqs1P/
NwdFGgpKHbV4r1Jeoosom+n7VnuyE0vYBKo8TlRks6NvQJoh2duiPkL+AsBgCfBq
fznck7jIPL4z4kf4Fp/Yz1QsmMhkDSidPmGD/m97Bj4wvEbMwf0u8Dnv1tySK5wx
NwKeN0Dn7JphtL5c5j+OGiri7gTcswjxHJ9f6d0Ez+2TwnjWFM6JNQ+xdVqFcxc=
=EpS9
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"I'd been collecting these whilst we debugged a CPU hotplug failure,
but we ended up diagnosing that one to tglx, who has taken a fix via
the -tip tree separately.
We're seeing some NFS issues that we haven't gotten to the bottom of
yet, and we've uncovered some issues with our backtracing too so there
might be another fixes pull before we're done.
Summary:
- Ensure we have a guard page after the kernel image in vmalloc
- Fix incorrect prefetch stride in copy_page
- Ensure irqs are disabled in die()
- Fix for event group validation in QCOM L2 PMU driver
- Fix requesting of PMU IRQs on AMD Seattle
- Minor cleanups and fixes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mmu: Place guard page after mapping of kernel image
drivers/perf: arm_pmu: Request PMU SPIs with IRQF_PER_CPU
arm64: sysreg: Fix unprotected macro argmuent in write_sysreg
perf: qcom_l2: fix column exclusion check
arm64/lib: copy_page: use consistent prefetch stride
arm64/numa: Drop duplicate message
perf: Convert to using %pOF instead of full_name
arm64: Convert to using %pOF instead of full_name
arm64: traps: disable irq in die()
arm64: atomics: Remove '&' from '+&' asm constraint in lse atomics
arm64: uaccess: Remove redundant __force from addr cast in __range_ok
Add node for the Amlogic Meson GX SoC information register.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The vast majority of virtual allocations in the vmalloc region are followed
by a guard page, which can help to avoid overruning on vma into another,
which may map a read-sensitive device.
This patch adds a guard page to the end of the kernel image mapping (i.e.
following the data/bss segments).
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The hardware spinlock drivers now depend on HWSPINLOCK (instead of
selecting it), so we need to explicitly enable it after commit
35fc8a07d7 ("Make HWSPINLOCK a menuconfig to ease disabling")
Without HWSPINLOCK, various drivers are left with unsatisfied
dependencies and Qcom boards using shared memory based communication
to request regulators are failing to boot and mount rootfs.
Fix this by explicitly enabling HWSPINLOCK in defconfig.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for hsusb ch3 device nodes for R-Car H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for usb-dmac ch2 and ch3 device nodes for
R-Car H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for usb2.0 host ch3 device nodes for R-Car
H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for usb3_phy ch3 device node for R-Car H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the "companion" property in the EHCI ch0, ch1 and
ch2 nodes to wait for the usb companion controller startup at resume.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[remove ch3 node and revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Renesas Draak board based on R-Car D3:
- Memory,
- Main crystal,
- Serial console,
- Watchdog.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a configuration option for the R-Car D3 SoC.
Note that r8a77995 is the first Renesas "r8a<n>" SoC using a 5 digit
number in its Kconfig symbol, as r8a77990 will be a different SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU dot clocks 0 and 3 are provided by the programmable VC6 clock
generator. Connect them to the clock source node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers. However, the second pair of corresponding DMA names was
missing.
Fixes: 80fab06e25 ("arm64: dts: r8a7796: Add all MSIOF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers, incl. clocks, power
domain, dma, and reset properties.
Due to a hardware erratum on R-Car H3 ES1.x, using MSIOF for SPI is only
supported on ES2.0 and later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a compatible string and VSP links to the DU node. The H3 ES1.x and
H3 ES2.0 are compatible save for the links to the VSPs that are
described explicitly in DT, so there's no need for a new ES2-specific
compatible string.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the HDMI encoder for ULCB board and hook it up to the HDMI connector.
The HDMI encoder and connector are available on both the H3 and M3-W ULCB boards.
Add them to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ULCB board has one HDMI output connector.
This connector is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0/DU1/DU2 external dot clocks are provided by the programmable
Versaclock5 clock generator.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0/DU1/DU2/DU3 external dot clocks are provided by the programmable
Versaclock5 clock generator.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU0/DU1/DU2/DU3 external dot clocks are generated by an I2C-controlled
programmable clock generator.
Clock generator is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the HDMI encoder for the M3-W Salvator-X board and hook it up to
the HDMI connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU2 clocks are provided by the
programmable Versaclock5 clock generator.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the HDMI encoder to the R8A7796 DT in disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a7796.dtsi in a disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the FDPs and VSP2s.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables I2C4 for ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables I2C for DVFS device for ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The definition of CPG_AUDIO_CLK_I is SoC-specific, not board-specific.
Hence move it from the board-specific .dts files to the SoC-specific
.dtsi files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IMR-LX4 devices in the R8A7796 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IMR-LX4 devices in the R8A7795 device tree.
Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: Konstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Compile the renesas sound and ak4613 drivers as modules to reduce the ARM64
kernel size. These modules are currently only used by Renesas platforms so
there should little risk of negative impact of this change on other users.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[simon: consolidated two patches into one]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The datasheet said that emac register size is 0x10000 not 0x100
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Fixed commit subject prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Correct order of sound clock frequencies for ULCB boards
used by r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bjUb
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Second Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
Correct order of sound clock frequencies for ULCB boards
used by r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
* tag 'renesas-fixes2-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: ulcb: sound clock-frequency needs descending order
Correct order of sound clock frequencies for Salvator boards
used by r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZVhaCAAoJENfPZGlqN0++/zkP/1aHxFA560O3cb4SebIeJKQd
TQFd7YocK1lsqD6DP1ZLQI7ytPfpyAKPctKLRe2NSwr+kf5N8rbYUfZ88pBXe7ez
y9mbFBYcKHvDLrGHtW5hebBGB6HAh2Ll9DMW6Hqdsv8qG1/EqlLwBkA10/VSjaYk
Xfp4XnbyXsWCxbllU04We0uel945rg6tQy6VBszW5QEwMEX4zhaOsmi6z8nCv11E
k8Q6xl2/+FWc/zfivJSzBn59XjQSo+E54yRkmaYcteTY2+8Y787QMvVKkbUAvnHi
DrVplSPdbQPeZInqDiw97fvUNDTIzYatskMF3Lv6HFZ+u8YHTrW6yq2CShWtecUx
7BP8GgwfkLHt8J5PADMpNejzfE5lz+7EPm8+2jhGeoHd0BNjojaFvbyL01pJntwp
nJrSKlLmRB1CDEiubVPUUrY+EWcx7wxK0V8eliWTAn/o1ijJTErbRF91Z/U9BACF
PQUToBZ8MJKbjbrFXmelswkTwORV7au0KwY6Jzm2Vue7TiCZU4BXwyxZ1hmH3dI1
GLOWo5mtlXWcUnHLrPv44x6povNQDCtPGowTyKkqo2vXIAlAkMaG4V5D2tV9ykr7
d0UDWA44fF7QYcgW8hEd1eY0ILnYuX7Zanh0xvb5OBjqLEwsf+FvLel6/eMzg4Pj
tNB+iosh5YumUfCIue0D
=t800
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
Correct order of sound clock frequencies for Salvator boards
used by r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
* tag 'renesas-fixes-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: salvator-common: sound clock-frequency needs descending order
write_sysreg() may misparse the value argument because it is used
without parentheses to protect it.
This patch adds the ( ) in order to avoid any surprises.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: same change to write_sysreg_s]
Signed-off-by: Will Deacon <will.deacon@arm.com>
- split the global dma coherent pool from the per-device pool.
This fixes a regression in the earlier 4.13 pull requests where the
global pool would override a per-device CMA pool. (Vladimir Murzin).
-----BEGIN PGP SIGNATURE-----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=fJWP
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping fixes from Christoph Hellwig:
"split the global dma coherent pool from the per-device pool.
This fixes a regression in the earlier 4.13 pull requests where the
global pool would override a per-device CMA pool (Vladimir Murzin)"
* tag 'dma-mapping-4.13-2' of git://git.infradead.org/users/hch/dma-mapping:
ARM: NOMMU: Wire-up default DMA interface
dma-coherent: introduce interface for default DMA pool
This allows basic support for SD highspeed cards but no UHS-I mode
got ready due to the propagated defer-probe error from RK805.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the core grf subnode for the io-domain controller.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
kvm_pmu_overflow_set() is called from perf's interrupt handler,
making the call of kvm_vgic_inject_irq() from it introduced with
"KVM: arm/arm64: PMU: remove request-less vcpu kick" a really bad
idea, as it's quite easy to try and retake a lock that the
interrupted context is already holding. The fix is to use a vcpu
kick, leaving the interrupt injection to kvm_pmu_sync_hwstate(),
like it was doing before the refactoring. We don't just revert,
though, because before the kick was request-less, leaving the vcpu
exposed to the request-less vcpu kick race, and also because the
kick was used unnecessarily from register access handlers.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The optional prefetch instructions in the copy_page() routine are
inconsistent: at the start of the function, two cachelines are
prefetched beyond the one being loaded in the first iteration, but
in the loop, the prefetch is one more line ahead. This appears to
be unintentional, so let's fix it.
While at it, fix the comment style and white space.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
LS1012A has one USB 3.0(DWC3) controller and
one USB 2.0 controller.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sparse complains about wrong address space used in __acpi_map_table()
and in __acpi_unmap_table().
arch/x86/kernel/acpi/boot.c:127:29: warning: incorrect type in return expression (different address spaces)
arch/x86/kernel/acpi/boot.c:127:29: expected char *
arch/x86/kernel/acpi/boot.c:127:29: got void [noderef] <asn:2>*
arch/x86/kernel/acpi/boot.c:135:23: warning: incorrect type in argument 1 (different address spaces)
arch/x86/kernel/acpi/boot.c:135:23: expected void [noderef] <asn:2>*addr
arch/x86/kernel/acpi/boot.c:135:23: got char *map
Correct address space to be in align of type of returned and passed
parameter.
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
struct siginfo is a union and the kernel since 2.4 has been hiding a union
tag in the high 16bits of si_code using the values:
__SI_KILL
__SI_TIMER
__SI_POLL
__SI_FAULT
__SI_CHLD
__SI_RT
__SI_MESGQ
__SI_SYS
While this looks plausible on the surface, in practice this situation has
not worked well.
- Injected positive signals are not copied to user space properly
unless they have these magic high bits set.
- Injected positive signals are not reported properly by signalfd
unless they have these magic high bits set.
- These kernel internal values leaked to userspace via ptrace_peek_siginfo
- It was possible to inject these kernel internal values and cause the
the kernel to misbehave.
- Kernel developers got confused and expected these kernel internal values
in userspace in kernel self tests.
- Kernel developers got confused and set si_code to __SI_FAULT which
is SI_USER in userspace which causes userspace to think an ordinary user
sent the signal and that it was not kernel generated.
- The values make it impossible to reorganize the code to transform
siginfo_copy_to_user into a plain copy_to_user. As si_code must
be massaged before being passed to userspace.
So remove these kernel internal si codes and make the kernel code simpler
and more maintainable.
To replace these kernel internal magic si_codes introduce the helper
function siginfo_layout, that takes a signal number and an si_code and
computes which union member of siginfo is being used. Have
siginfo_layout return an enumeration so that gcc will have enough
information to warn if a switch statement does not handle all of union
members.
A couple of architectures have a messed up ABI that defines signal
specific duplications of SI_USER which causes more special cases in
siginfo_layout than I would like. The good news is only problem
architectures pay the cost.
Update all of the code that used the previous magic __SI_ values to
use the new SIL_ values and to call siginfo_layout to get those
values. Escept where not all of the cases are handled remove the
defaults in the switch statements so that if a new case is missed in
the future the lack will show up at compile time.
Modify the code that copies siginfo si_code to userspace to just copy
the value and not cast si_code to a short first. The high bits are no
longer used to hold a magic union member.
Fixup the siginfo header files to stop including the __SI_ values in
their constants and for the headers that were missing it to properly
update the number of si_codes for each signal type.
The fixes to copy_siginfo_from_user32 implementations has the
interesting property that several of them perviously should never have
worked as the __SI_ values they depended up where kernel internal.
With that dependency gone those implementations should work much
better.
The idea of not passing the __SI_ values out to userspace and then
not reinserting them has been tested with criu and criu worked without
changes.
Ref: 2.4.0-test1
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The SoPine SoM has an AXP803 PMIC connected to the RSB bus of the A64
SoC, and the regulators of the PMIC are used both on the SoM itself and
on the official baseboard
Add related device tree parts to the SoPine SoM DTSI file and the
baseboard DT.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support of AXP803 regulators in the Pine64 device tree.
The phy-supply regulator is also set in EMAC device node, in order to
prevent Ethernet regression by regulator get disabled by regulator
framework.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Kill these two pinctrl reference totally from rk3399 as it
never work indeed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables the gpu and adds the mali-supply power for RK3399-GRU
devices.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add Mali GPU device tree node for the RK3399 SoCs, with devfreq
opp table.
RK3399 and RK3399-OP1 SoCs have a different recommendation table with
gpu opp. Also, the ARM's mali driver found on
https://developer.arm.com/products/software/mali-drivers/midgard-kernel.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
keep-power-in-suspend was invented for SDIO only, so it should
not be used for eMMC node.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
the mailbox and ethmac nodes used the magic number "0" instead of the
GIC_SPI preprocessor macro. Additionally the ethmac used the magic
number "1" instead of IRQ_TYPE_EDGE_RISING.
Fix this to make the .dtsi easier to read.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull core fixes from Ingo Molnar:
"A fix to WARN_ON_ONCE() done by modules, plus a MAINTAINERS update"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debug: Fix WARN_ON_ONCE() for modules
MAINTAINERS: Update the PTRACE entry
The libretech CC derives less from the p212 than initially thought.
Several voltage regulators are different and the capabilities of the
sdcard and emmc also differ.
Deriving from the p212 is not convient anymore so the libretech is now
derived from s905x definition directly.
Fixes: cd84aff1d9 ("ARM64: dts: meson-gxl: Add Libre Technology CC support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Use the specific compatible for AO pwms so the pwms input can
be correctly set
FDIV4 is not present on the pwm A0, so change kadhas vim input
clocks to xtal.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Christoph noticed [1] that default DMA pool in current form overload
the DMA coherent infrastructure. In reply, Robin suggested [2] to
split the per-device vs. global pool interfaces, so allocation/release
from default DMA pool is driven by dma ops implementation.
This patch implements Robin's idea and provide interface to
allocate/release/mmap the default (aka global) DMA pool.
To make it clear that existing *_from_coherent routines work on
per-device pool rename them to *_from_dev_coherent.
[1] https://lkml.org/lkml/2017/7/7/370
[2] https://lkml.org/lkml/2017/7/7/431
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Andras Szemzo <sza@esh.hu>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Warnings:
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the support for the MT7622 reference board variant 1 from
MediaTek.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add basic nodes into the mt7622.dtsi for the system
bring-up which includes ARM CPU, GIC, timer, MediaTek
UART, SYSIRQ and one reserved memory region for ATF.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Mike Galbraith reported a situation where a WARN_ON_ONCE() call in DRM
code turned into an oops. As it turns out, WARN_ON_ONCE() seems to be
completely broken when called from a module.
The bug was introduced with the following commit:
19d436268d ("debug: Add _ONCE() logic to report_bug()")
That commit changed WARN_ON_ONCE() to move its 'once' logic into the bug
trap handler. It requires a writable bug table so that the BUGFLAG_DONE
bit can be written to the flags to indicate the first warning has
occurred.
The bug table was made writable for vmlinux, which relies on
vmlinux.lds.S and vmlinux.lds.h for laying out the sections. However,
it wasn't made writable for modules, which rely on the ELF section
header flags.
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 19d436268d ("debug: Add _ONCE() logic to report_bug()")
Link: http://lkml.kernel.org/r/a53b04235a65478dd9afc51f5b329fdc65c84364.1500095401.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
In current die(), the irq is disabled for __die() handle, not
including the possible panic() handling. Since the log in __die()
can take several hundreds ms, new irq might come and interrupt
current die().
If the process calling die() holds some critical resource, and some
other process scheduled later also needs it, then it would deadlock.
The first panic will not be executed.
So here disable irq for the whole flow of die().
Signed-off-by: Qiao Zhou <qiaozhou@asrmicro.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The lse implementation of atomic64_dec_if_positive uses the '+&' constraint,
but the '&' is redundant and confusing in this case, since early clobber
on a read/write operand is a strange concept.
Replace the constraint with '+'.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Casting a pointer to an integral type doesn't require a __force
attribute, because you'll need to cast back to a pointer in order to
dereference the thing anyway.
This patch removes the redundant __force cast from __range_ok.
Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The crypto engines found on the cp110 master and slave are dma coherent.
This patch adds the relevant property to their dt nodes.
Cc: stable@vger.kernel.org # v4.12+
Fixes: 973020fd94 ("arm64: marvell: dts: add crypto engine description for 7k/8k")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When the conversion of the Marvell CP110 Device Tree description from
using GIC interrupts to using ICU interrupts was done, the RTC on the
slave CP110 was left unchanged. This commit fixes that, so that all
devices on the CP properly get their interrupt through the ICU.
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit enables the nop-xceiv PHY driver, which is needed for USB
support to work on the MacchiatoBin platform (Marvell Armada 8K).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since commit 9840354ff4 ("usb: dwc3: Add dual-role support") dwc3
node requires extcon property to be initialized as OTG mode and it
supports dual-role mode operation.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5433 has two usb 3.0 controllers: usbhost and usbdrd. usbhost
is host-only controller whereas usbdrd supports both peripheral and
host mode. "drd" means dual-role device, so usbhost cannot be labeled
with the name containing "drd". However, the label usbdrd_dwc3_0 was
used for usbhost's dwc3 node. It seems it obviously fault because TM2
and TM2E doesn't use usbhost but dr_mode property is assigned to it.
This patch assigns the proper label for two dwc3 nodes.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The OF graph is not needed because the panel is a child of dsi. Remove
the ports node in DSI node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As nearly all A64 boards are using AXP803 PMIC, add a DTSI file for it,
like the old DTSI files for AXP20x/22x, for the common parts of the
PMIC.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Pine64 (including Pine64+) boards have an AXP803 as its main PMIC.
Add its device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner A64 SoC features a R_INTC controller, which controls the NMI
line, and this interrupt line is usually connected to the AXP PMIC.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Add fallback sun6i-a31-r-intc compatible]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We deprecated the "num-slots" property now and plan to get
rid of it finally. Just move a step to cleanup it from DT.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SdioAudio power domain includes the i2s/spdif/spi5/sdio.
So this patch adds the pd control for rk3399 i2s/spdif/spi5/sdio, in order
to save more power consumption.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip's RK3328 evaluation board has one usb2 otg controller
and one usb2 host controller which consist of EHCI and OHCI.
Each usb controller connects with one usb2 phy port through
UTMI+ interface. Let's enable them to support usb2 on RK3328
evaluation board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
[restructured enablement of u2phy subnodes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Provide the dynamic power coefficient of the big and little CPU
clusters. These numbers are currently in use on the Samsung Chromebook
Plus ("Kevin").
The power allocator thermal governor doesn't know how to do anything if
it doesn't get power parameters from its cooling devices (in this case,
CPUfreq). So this effectively enables the power-allocator governor.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[set the property in each core node]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Gru device tree currently contains entries for the regulators
ppvar_bigcpu, ppvar_litcpu, ppvar_gpu and ppvar_centerlogic; however,
the regulators have not been enabled, due to the lack of binding and driver
support for keeping the over-voltage protection (OVP) at bay and
preventing unintended regulator shutdowns on voltage downshifts.
Now, the vctrl regulator driver has been merged, along with new bindings
for asymmetric settling time. The driver is OVP aware, it splits larger
voltage decreases in multiple steps when necessary and adds required
delays.
This change renames each of the aforementioned regulators to
<orig_name>_pwm and adds a new vctrl regulator named <orig_name>.
The vctrl regulators use the voltage of their corresponding PWM regulator
as control voltage. The OVP related values are empirical and stem from
the Chrome OS kernel tree.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
[fixed node names and parent supplies of gpu and centerlogic]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Gru derivatives besides Kevin have slightly different voltage ranges for
their CPU regulators. Let's keep the base Gru file accurate and let
Kevin override.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
replace all occurrences of sdmcc with sdmmc in the arm64 rockchip
devicetree files.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add nodes of watchdog timer for UniPhier LD11 and LD20 SoC.
The watchdog timer is included in sysctrl.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull uacess-unaligned removal from Al Viro:
"That stuff had just one user, and an exotic one, at that - binfmt_flat
on arm and m68k"
* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill {__,}{get,put}_user_unaligned()
binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail
- Move generic-y of exported headers to uapi/asm/Kbuild
for complete de-coupling of UAPI
- Clean up scripts/Makefile.headersinst
- Fix host programs for 32 bit machine with XFS file system
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Sw8W
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Move generic-y of exported headers to uapi/asm/Kbuild for complete
de-coupling of UAPI
- Clean up scripts/Makefile.headersinst
- Fix host programs for 32 bit machine with XFS file system
* tag 'kbuild-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (29 commits)
kbuild: Enable Large File Support for hostprogs
kbuild: remove wrapper files handling from Makefile.headersinst
kbuild: split exported generic header creation into uapi-asm-generic
kbuild: do not include old-kbuild-file from Makefile.headersinst
xtensa: move generic-y of exported headers to uapi/asm/Kbuild
unicore32: move generic-y of exported headers to uapi/asm/Kbuild
tile: move generic-y of exported headers to uapi/asm/Kbuild
sparc: move generic-y of exported headers to uapi/asm/Kbuild
sh: move generic-y of exported headers to uapi/asm/Kbuild
parisc: move generic-y of exported headers to uapi/asm/Kbuild
openrisc: move generic-y of exported headers to uapi/asm/Kbuild
nios2: move generic-y of exported headers to uapi/asm/Kbuild
nios2: remove unneeded arch/nios2/include/(generated/)asm/signal.h
microblaze: move generic-y of exported headers to uapi/asm/Kbuild
metag: move generic-y of exported headers to uapi/asm/Kbuild
m68k: move generic-y of exported headers to uapi/asm/Kbuild
m32r: move generic-y of exported headers to uapi/asm/Kbuild
ia64: remove redundant generic-y += kvm_para.h from asm/Kbuild
hexagon: move generic-y of exported headers to uapi/asm/Kbuild
h8300: move generic-y of exported headers to uapi/asm/Kbuild
...
When RLIMIT_STACK is, for example, 256MB, the current code results in a
gap between the top of the task and mmap_base of 256MB, failing to take
into account the amount by which the stack address was randomized. In
other words, the stack gets less than RLIMIT_STACK space.
Ensure that the gap between the stack and mmap_base always takes stack
randomization and the stack guard gap into account.
Obtained from Daniel Micay's linux-hardened tree.
Link: http://lkml.kernel.org/r/20170622200033.25714-3-riel@redhat.com
Signed-off-by: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Florian Weimer <fweimer@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the ascii-armor canary to prevent unterminated C string overflows
from being able to successfully overwrite the canary, even if they
somehow obtain the canary value.
Inspired by execshield ascii-armor and Daniel Micay's linux-hardened
tree.
Link: http://lkml.kernel.org/r/20170524155751.424-5-riel@redhat.com
Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for compiling with a rough equivalent to the glibc
_FORTIFY_SOURCE=1 feature, providing compile-time and runtime buffer
overflow checks for string.h functions when the compiler determines the
size of the source or destination buffer at compile-time. Unlike glibc,
it covers buffer reads in addition to writes.
GNU C __builtin_*_chk intrinsics are avoided because they would force a
much more complex implementation. They aren't designed to detect read
overflows and offer no real benefit when using an implementation based
on inline checks. Inline checks don't add up to much code size and
allow full use of the regular string intrinsics while avoiding the need
for a bunch of _chk functions and per-arch assembly to avoid wrapper
overhead.
This detects various overflows at compile-time in various drivers and
some non-x86 core kernel code. There will likely be issues caught in
regular use at runtime too.
Future improvements left out of initial implementation for simplicity,
as it's all quite optional and can be done incrementally:
* Some of the fortified string functions (strncpy, strcat), don't yet
place a limit on reads from the source based on __builtin_object_size of
the source buffer.
* Extending coverage to more string functions like strlcat.
* It should be possible to optionally use __builtin_object_size(x, 1) for
some functions (C strings) to detect intra-object overflows (like
glibc's _FORTIFY_SOURCE=2), but for now this takes the conservative
approach to avoid likely compatibility issues.
* The compile-time checks should be made available via a separate config
option which can be enabled by default (or always enabled) once enough
time has passed to get the issues it catches fixed.
Kees said:
"This is great to have. While it was out-of-tree code, it would have
blocked at least CVE-2016-3858 from being exploitable (improper size
argument to strlcpy()). I've sent a number of fixes for
out-of-bounds-reads that this detected upstream already"
[arnd@arndb.de: x86: fix fortified memcpy]
Link: http://lkml.kernel.org/r/20170627150047.660360-1-arnd@arndb.de
[keescook@chromium.org: avoid panic() in favor of BUG()]
Link: http://lkml.kernel.org/r/20170626235122.GA25261@beast
[keescook@chromium.org: move from -mm, add ARCH_HAS_FORTIFY_SOURCE, tweak Kconfig help]
Link: http://lkml.kernel.org/r/20170526095404.20439-1-danielmicay@gmail.com
Link: http://lkml.kernel.org/r/1497903987-21002-8-git-send-email-keescook@chromium.org
Signed-off-by: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that explicitly executed loaders are loaded in the mmap region, we
have more freedom to decide where we position PIE binaries in the
address space to avoid possible collisions with mmap or stack regions.
For 64-bit, align to 4GB to allow runtimes to use the entire 32-bit
address space for 32-bit pointers. On 32-bit use 4MB, to match ARM.
This could be 0x8000, the standard ET_EXEC load address, but that is
needlessly close to the NULL address, and anyone running arm compat PIE
will have an MMU, so the tight mapping is not needed.
Link: http://lkml.kernel.org/r/1498251600-132458-4-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to read several bytes of the shadow memory in advance.
Therefore additional shadow memory mapped to prevent crash if
speculative load would happen near the end of the mapped shadow memory.
Now we don't have such speculative loads, so we no longer need to map
additional shadow memory.
Link: http://lkml.kernel.org/r/20170601162338.23540-3-aryabinin@virtuozzo.com
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct order of sound clock frequencies for ULCB boards
used with r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
Fixes: 9f22774c21 ("arm64: dts: ulcb: add 12288000 for sound ADG")
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rewrote changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit fcc8487d47 ("uapi: export all headers under uapi
directories"), all (and only) headers under uapi directories are
exported, but asm-generic wrappers are still exceptions.
To complete de-coupling the uapi from kernel headers, move generic-y
of exported headers to uapi/asm/Kbuild.
With this change, "make headers_install" will just need to parse
uapi/asm/Kbuild to build up exported headers.
For arm64, "generic-y += kvm_para.h" is doubled in asm/Kbuild and
uapi/asm/Kbuild. So, the one in the former can be simply removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Ensure the address limit is a user-mode segment before returning to
user-mode. Otherwise a process can corrupt kernel-mode memory and
elevate privileges [1].
The set_fs function sets the TIF_SETFS flag to force a slow path on
return. In the slow path, the address limit is checked to be USER_DS if
needed.
[1] https://bugs.chromium.org/p/project-zero/issues/detail?id=990
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: kernel-hardening@lists.openwall.com
Cc: Will Deacon <will.deacon@arm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Will Drewry <wad@chromium.org>
Cc: linux-api@vger.kernel.org
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: http://lkml.kernel.org/r/20170615011203.144108-3-thgarnie@google.com
Merge misc updates from Andrew Morton:
- a few hotfixes
- various misc updates
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (108 commits)
mm, memory_hotplug: move movable_node to the hotplug proper
mm, memory_hotplug: drop CONFIG_MOVABLE_NODE
mm, memory_hotplug: drop artificial restriction on online/offline
mm: memcontrol: account slab stats per lruvec
mm: memcontrol: per-lruvec stats infrastructure
mm: memcontrol: use generic mod_memcg_page_state for kmem pages
mm: memcontrol: use the node-native slab memory counters
mm: vmstat: move slab statistics from zone to node counters
mm/zswap.c: delete an error message for a failed memory allocation in zswap_dstmem_prepare()
mm/zswap.c: improve a size determination in zswap_frontswap_init()
mm/zswap.c: delete an error message for a failed memory allocation in zswap_pool_create()
mm/swapfile.c: sort swap entries before free
mm/oom_kill: count global and memory cgroup oom kills
mm: per-cgroup memory reclaim stats
mm: kmemleak: treat vm_struct as alternative reference to vmalloc'ed objects
mm: kmemleak: factor object reference updating out of scan_block()
mm: kmemleak: slightly reduce the size of some structures on 64-bit architectures
mm, mempolicy: don't check cpuset seqlock where it doesn't matter
mm, cpuset: always use seqlock when changing task's nodemask
mm, mempolicy: simplify rebinding mempolicies when updating cpusets
...
Pull user access str* updates from Al Viro:
"uaccess str...() dead code removal"
* 'uaccess.strlen' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
s390 keyboard.c: don't open-code strndup_user()
mips: get rid of unused __strnlen_user()
get rid of unused __strncpy_from_user() instances
kill strlen_user()
- Added TRACE_DEFINE_SIZEOF() which allows trace events that use
sizeof() it the TP_printk() to be converted to the actual size such
that trace-cmd and perf can parse them correctly.
- Some rework of the TRACE_DEFINE_ENUM() such that the above
TRACE_DEFINE_SIZEOF() could reuse the same code.
- Recording of tgid (Thread Group ID). This is similar to how
task COMMs are recorded (cached at sched_switch), where it is
in a table and used on output of the trace and trace_pipe files.
- Have ":mod:<module>" be cached when written into set_ftrace_filter.
Then the functions of the module will be traced at module load.
- Some random clean ups and small fixes.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJZXjYuFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
fsgIAKUvhpn2igoYCR9tWqu+DovEmwxCIumbCzmCFQcRKlLttRte94yY5+W9hnV0
JPzd9T9zBDVqq1fI7iIop1SuTwEfKW6lJom0usZ8AFpK+YKm6FHnQ28POlvHzre2
lzO41tpRWiehLQsITZ47eByhsvEfhx86mYT/oM1JSR6Pii1OpjyNYmDMw6BaMNBT
kSCQFgIhzAhVuHjwAnB/S++E/ou7M5bCwCb5CNh7MubKubV5upHpoJcgYGO+WWa6
56H/iEhff4EECTGJVefd8e78MtJPL8EsuM0nAcMPlnl8AaiOpP7XCdlgTwdefLvP
b3o+nP15voSHkARGXC6eM6gH0po=
=rvGB
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The new features of this release:
- Added TRACE_DEFINE_SIZEOF() which allows trace events that use
sizeof() it the TP_printk() to be converted to the actual size such
that trace-cmd and perf can parse them correctly.
- Some rework of the TRACE_DEFINE_ENUM() such that the above
TRACE_DEFINE_SIZEOF() could reuse the same code.
- Recording of tgid (Thread Group ID). This is similar to how task
COMMs are recorded (cached at sched_switch), where it is in a table
and used on output of the trace and trace_pipe files.
- Have ":mod:<module>" be cached when written into set_ftrace_filter.
Then the functions of the module will be traced at module load.
- Some random clean ups and small fixes"
* tag 'trace-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (26 commits)
ftrace: Test for NULL iter->tr in regex for stack_trace_filter changes
ftrace: Decrement count for dyn_ftrace_total_info for init functions
ftrace: Unlock hash mutex on failed allocation in process_mod_list()
tracing: Add support for display of tgid in trace output
tracing: Add support for recording tgid of tasks
ftrace: Decrement count for dyn_ftrace_total_info file
ftrace: Remove unused function ftrace_arch_read_dyn_info()
sh/ftrace: Remove only user of ftrace_arch_read_dyn_info()
ftrace: Have cached module filters be an active filter
ftrace: Implement cached modules tracing on module load
ftrace: Have the cached module list show in set_ftrace_filter
ftrace: Add :mod: caching infrastructure to trace_array
tracing: Show address when function names are not found
ftrace: Add missing comment for FTRACE_OPS_FL_RCU
tracing: Rename update the enum_map file
tracing: Add TRACE_DEFINE_SIZEOF() macros
tracing: define TRACE_DEFINE_SIZEOF() macro to map sizeof's to their values
tracing: Rename enum_replace to eval_replace
trace: rename enum_map functions
trace: rename trace.c enum functions
...
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls
to ->mapping_error so that the dma_map_ops instances are
more self contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)
-----BEGIN PGP SIGNATURE-----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=0Fso
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements
There is a small conflict in arch/s390 due to an arch-wide field rename.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZW4XTAAoJEL/70l94x66DkhMH/izpk54KI17PtyQ9VYI2sYeZ
BWK6Kl886g3ij4pFi3pECqjDJzWaa3ai+vFfzzpJJ8OkCJT5Rv4LxC5ERltVVmR8
A3T1I/MRktSC0VJLv34daPC2z4Lco/6SPipUpPnL4bE2HATKed4vzoOjQ3tOeGTy
dwi7TFjKwoVDiM7kPPDRnTHqCe5G5n13sZ49dBe9WeJ7ttJauWqoxhlYosCGNPEj
g8ZX8+cvcAhVnz5uFL8roqZ8ygNEQq2mgkU18W8ZZKuiuwR0gdsG0gSBFNTdwIMK
NoreRKMrw0+oLXTIB8SZsoieU6Qi7w3xMAMabe8AJsvYtoersugbOmdxGCr1lsA=
=OD7H
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"PPC:
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
Update my email address
kvm: vmx: allow host to access guest MSR_IA32_BNDCFGS
x86: kvm: mmu: use ept a/d in vmcs02 iff used in vmcs12
kvm: x86: mmu: allow A/D bits to be disabled in an mmu
x86: kvm: mmu: make spte mmio mask more explicit
x86: kvm: mmu: dead code thanks to access tracking
KVM: PPC: Book3S: Fix typo in XICS-on-XIVE state saving code
KVM: PPC: Book3S HV: Close race with testing for signals on guest entry
KVM: PPC: Book3S HV: Simplify dynamic micro-threading code
KVM: x86: remove ignored type attribute
KVM: LAPIC: Fix lapic timer injection delay
KVM: lapic: reorganize restart_apic_timer
KVM: lapic: reorganize start_hv_timer
kvm: nVMX: Check memory operand to INVVPID
KVM: s390: Inject machine check into the nested guest
KVM: s390: Inject machine check into the guest
tools/kvm_stat: add new interactive command 'b'
tools/kvm_stat: add new command line switch '-i'
tools/kvm_stat: fix error on interactive command 'g'
KVM: SVM: suppress unnecessary NMI singlestep on GIF=0 and nested exit
...
A poisoned or migrated hugepage is stored as a swap entry in the page
tables. On architectures that support hugepages consisting of
contiguous page table entries (such as on arm64) this leads to ambiguity
in determining the page table entry to return in huge_pte_offset() when
a poisoned entry is encountered.
Let's remove the ambiguity by adding a size parameter to convey
additional information about the requested address. Also fixup the
definition/usage of huge_pte_offset() throughout the tree.
Link: http://lkml.kernel.org/r/20170522133604.11392-4-punit.agrawal@arm.com
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com> (odd fixer:METAG ARCHITECTURE)
Cc: Ralf Baechle <ralf@linux-mips.org> (supporter:MIPS)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need to call huge_ptep_offset as our accessors are already
supplied with the pte_t *. This patch removes those spurious calls.
[punit.agrawal@arm.com: resolve rebase conflicts due to patch re-ordering]
Link: http://lkml.kernel.org/r/20170524115409.31309-3-punit.agrawal@arm.com
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: David Woods <dwoods@mellanox.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Support for contiguous pte hugepages", v4.
This patchset updates the hugetlb code to fix issues arising from
contiguous pte hugepages (such as on arm64). Compared to v3, This
version addresses a build failure on arm64 by including two cleanup
patches. Other than the arm64 cleanups, the rest are generic code
changes. The remaining arm64 support based on these patches will be
posted separately. The patches are based on v4.12-rc2. Previous
related postings can be found at [0], [1], [2], and [3].
The patches fall into three categories -
* Patch 1-2 - arm64 cleanups required to greatly simplify changing
huge_pte_offset() prototype in Patch 5.
Catalin, Will - are you happy for these patches to go via mm?
* Patches 3-4 address issues with gup
* Patches 5-8 relate to passing a size argument to hugepage helpers to
disambiguate the size of the referred page. These changes are
required to enable arch code to properly handle swap entries for
contiguous pte hugepages.
The changes to huge_pte_offset() (patch 5) touch multiple
architectures but I've managed to minimise these changes for the
other affected functions - huge_pte_clear() and set_huge_pte_at().
These patches gate the enabling of contiguous hugepages support on arm64
which has been requested for systems using !4k page granule.
The ARM64 architecture supports two flavours of hugepages -
* Block mappings at the pud/pmd level
These are regular hugepages where a pmd or a pud page table entry
points to a block of memory. Depending on the PAGE_SIZE in use the
following size of block mappings are supported -
PMD PUD
--- ---
4K: 2M 1G
16K: 32M
64K: 512M
For certain applications/usecases such as HPC and large enterprise
workloads, folks are using 64k page size but the minimum hugepage size
of 512MB isn't very practical.
To overcome this ...
* Using the Contiguous bit
The architecture provides a contiguous bit in the translation table
entry which acts as a hint to the mmu to indicate that it is one of a
contiguous set of entries that can be cached in a single TLB entry.
We use the contiguous bit in Linux to increase the mapping size at the
pmd and pte (last) level.
The number of supported contiguous entries varies by page size and
level of the page table.
Using the contiguous bit allows additional hugepage sizes -
CONT PTE PMD CONT PMD PUD
-------- --- -------- ---
4K: 64K 2M 32M 1G
16K: 2M 32M 1G
64K: 2M 512M 16G
Of these, 64K with 4K and 2M with 64K pages have been explicitly
requested by a few different users.
Entries with the contiguous bit set are required to be modified all
together - which makes things like memory poisoning and migration
impossible to do correctly without knowing the size of hugepage being
dealt with - the reason for adding size parameter to a few of the
hugepage helpers in this series.
This patch (of 8):
As we regularly check for contiguous pte's in the huge accessors, remove
this extra check from find_num_contig.
[punit.agrawal@arm.com: resolve rebase conflicts due to patch re-ordering]
Link: http://lkml.kernel.org/r/20170524115409.31309-2-punit.agrawal@arm.com
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: David Woods <dwoods@mellanox.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the #ifdef in C code to a Kconfig dependency. Also we move
the gigantic_page_supported() function to be arch specific.
This allows architectures to conditionally enable runtime allocation of
gigantic huge page. Architectures like ppc64 supports different
gigantic huge page size (16G and 1G) based on the translation mode
selected. This provides an opportunity for ppc64 to enable runtime
allocation only w.r.t 1G hugepage.
No functional change in this patch.
Link: http://lkml.kernel.org/r/1494995292-4443-1-git-send-email-aneesh.kumar@linux.vnet.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Changes to platform code for 64-bit ARM platforms.
Andreas Färber adds two new platforms with initial code: Realtek RTD1295
and Action Semi S900. Both are fairly similar chips, used mainly in
set-top-boxes, but with other possible applications, and additional
members in the respective product families that could be added in the
future. The code here is fairly minimal, as all the interesting parts
are in device drivers and dts files.
The Broadcom Vulcan platform gets dropped, as no products ever became
available, and Cavium integrated the platform under a new name.
Among some other defconfig changes, Timur Tabi enables a number of
options that are typically required for server platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=771F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms.
Andreas Färber adds two new platforms with initial code: Realtek
RTD1295 and Action Semi S900. Both are fairly similar chips, used
mainly in set-top-boxes, but with other possible applications, and
additional members in the respective product families that could be
added in the future. The code here is fairly minimal, as all the
interesting parts are in device drivers and dts files.
The Broadcom Vulcan platform gets dropped, as no products ever became
available, and Cavium integrated the platform under a new name.
Among some other defconfig changes, Timur Tabi enables a number of
options that are typically required for server platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: remove duplicate entry
arm64: defconfig: enable Qualcomm Technologies EMAC and some PHY drivers
arm64: defconfig: enable QCOM_L2_PMU and QCOM_L3_PMU
arm64: defconfig: enable EDAC options
arm64: defconfig: enable APEI and GHES features
arm64: defconfig: enable support for PCIe hotplug
arm64: defconfig: enable EFI_CAPSULE_LOADER
arm64: defconfig: enable BLK_DEV_NVME
arm64: defconfig: enable ACPI_CPPC_CPUFREQ
arm64: marvell: enable ICU and GICP drivers
arm64: marvell: enable the Armada 7K/8K pinctrl driver
arm64: Prepare Actions Semi S900
ARM64: defconfig: enable meson SPICC as module
ARM64: defconfig: enable IR core, decoders and Meson IR device
arm64: defconfig: enable Simple Sound Card support
arm64: defconfig: Enable ARCH_BRCMSTB
arm64: defconfig: drop ARCH_VULCAN
arm64: disable Broadcom Vulcan platform
MAINTAINERS: Add Realtek section
ARM64: Prepare Realtek RTD1295
Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer
gets added, this one stands out for being relatively fast,
affordable and well₋supported, compared to many boards that
only fall into one or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform
and corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win,
Orangepi Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single
board computers and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB
automotive development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets
extended significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E8pa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer gets
added, this one stands out for being relatively fast, affordable
and well₋supported, compared to many boards that only fall into one
or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform and
corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win, Orangepi
Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single board computers
and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB automotive
development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets extended
significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (243 commits)
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Revert "arm64: dts: marvell: add dma-mask in crypto nodes for 7k/8k"
arm64: dts: mediatek: don't include missing file
ARM64: dts: meson-gxl: Add Libre Technology CC support
dt-bindings: arm: amlogic: Add Libre Technology CC board
dt-bindings: add Libre Technology vendor prefix
arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K
arm64: dts: zte: Use - instead of @ for DT OPP entries
arm64: dts: marvell: add gpio support for Armada 7K/8K
arm64: dts: marvell: add pinctrl support for Armada 7K/8K
arm64: dts: marvell: use new binding for the system controller on cp110
arm64: dts: marvell: remove *-clock-output-names on cp110
arm64: dts: marvell: use new bindings for xor clocks on ap806
arm64: dts: marvell: mcbin: enable the mdio node
arm64: dts: Add Actions Semi S900 and Bubblegum-96
dt-bindings: Add vendor prefix for uCRobotics
arm64: dts: marvell: add xmdio nodes for 7k/8k
arm64: dts: marvell: add a comment on the cp110 slave node status
arm64: dts: marvell: remove cpm crypto nodes from dts files
arm64: dts: marvell: cp110: enable the crypto engine at the SoC level
...
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
Pull timer updates from Thomas Gleixner:
"A rather large update for timers/timekeeping:
- compat syscall consolidation (Al Viro)
- Posix timer consolidation (Christoph Helwig / Thomas Gleixner)
- Cleanup of the device tree based initialization for clockevents and
clocksources (Daniel Lezcano)
- Consolidation of the FTTMR010 clocksource/event driver (Linus
Walleij)
- The usual set of small fixes and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (93 commits)
timers: Make the cpu base lock raw
clocksource/drivers/mips-gic-timer: Fix an error code in 'gic_clocksource_of_init()'
clocksource/drivers/fsl_ftm_timer: Unmap region obtained by of_iomap
clocksource/drivers/tcb_clksrc: Make IO endian agnostic
clocksource/drivers/sun4i: Switch to the timer-of common init
clocksource/drivers/timer-of: Fix invalid iomap check
Revert "ktime: Simplify ktime_compare implementation"
clocksource/drivers: Fix uninitialized variable use in timer_of_init
kselftests: timers: Add test for frequency step
kselftests: timers: Fix inconsistency-check to not ignore first timestamp
time: Add warning about imminent deprecation of CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Clean up CLOCK_MONOTONIC_RAW time handling
posix-cpu-timers: Make timespec to nsec conversion safe
itimer: Make timeval to nsec conversion range limited
timers: Fix parameter description of try_to_del_timer_sync()
ktime: Simplify ktime_compare implementation
clocksource/drivers/fttmr010: Factor out clock read code
clocksource/drivers/fttmr010: Implement delay timer
clocksource/drivers: Add timer-of common init routine
clocksource/drivers/tcb_clksrc: Save timer context on suspend/resume
...
Pull x86 mm updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued work to add support for 5-level paging provided by future
Intel CPUs. In particular we switch the x86 GUP code to the generic
implementation. (Kirill A. Shutemov)
- Continued work to add PCID CPU support to native kernels as well.
In this round most of the focus is on reworking/refreshing the TLB
flush infrastructure for the upcoming PCID changes. (Andy
Lutomirski)"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
x86/mm: Delete a big outdated comment about TLB flushing
x86/mm: Don't reenter flush_tlb_func_common()
x86/KASLR: Fix detection 32/64 bit bootloaders for 5-level paging
x86/ftrace: Exclude functions in head64.c from function-tracing
x86/mmap, ASLR: Do not treat unlimited-stack tasks as legacy mmap
x86/mm: Remove reset_lazy_tlbstate()
x86/ldt: Simplify the LDT switching logic
x86/boot/64: Put __startup_64() into .head.text
x86/mm: Add support for 5-level paging for KASLR
x86/mm: Make kernel_physical_mapping_init() support 5-level paging
x86/mm: Add sync_global_pgds() for configuration with 5-level paging
x86/boot/64: Add support of additional page table level during early boot
x86/boot/64: Rename init_level4_pgt and early_level4_pgt
x86/boot/64: Rewrite startup_64() in C
x86/boot/compressed: Enable 5-level paging during decompression stage
x86/boot/efi: Define __KERNEL32_CS GDT on 64-bit configurations
x86/boot/efi: Fix __KERNEL_CS definition of GDT entry on 64-bit configurations
x86/boot/efi: Cleanup initialization of GDT entries
x86/asm: Fix comment in return_from_SYSCALL_64()
x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Add the SYSTEM_SCHEDULING bootup state to move various scheduler
debug checks earlier into the bootup. This turns silent and
sporadically deadly bugs into nice, deterministic splats. Fix some
of the splats that triggered. (Thomas Gleixner)
- A round of restructuring and refactoring of the load-balancing and
topology code (Peter Zijlstra)
- Another round of consolidating ~20 of incremental scheduler code
history: this time in terms of wait-queue nomenclature. (I didn't
get much feedback on these renaming patches, and we can still
easily change any names I might have misplaced, so if anyone hates
a new name, please holler and I'll fix it.) (Ingo Molnar)
- sched/numa improvements, fixes and updates (Rik van Riel)
- Another round of x86/tsc scheduler clock code improvements, in hope
of making it more robust (Peter Zijlstra)
- Improve NOHZ behavior (Frederic Weisbecker)
- Deadline scheduler improvements and fixes (Luca Abeni, Daniel
Bristot de Oliveira)
- Simplify and optimize the topology setup code (Lauro Ramos
Venancio)
- Debloat and decouple scheduler code some more (Nicolas Pitre)
- Simplify code by making better use of llist primitives (Byungchul
Park)
- ... plus other fixes and improvements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
sched/cputime: Refactor the cputime_adjust() code
sched/debug: Expose the number of RT/DL tasks that can migrate
sched/numa: Hide numa_wake_affine() from UP build
sched/fair: Remove effective_load()
sched/numa: Implement NUMA node level wake_affine()
sched/fair: Simplify wake_affine() for the single socket case
sched/numa: Override part of migrate_degrades_locality() when idle balancing
sched/rt: Move RT related code from sched/core.c to sched/rt.c
sched/deadline: Move DL related code from sched/core.c to sched/deadline.c
sched/cpuset: Only offer CONFIG_CPUSETS if SMP is enabled
sched/fair: Spare idle load balancing on nohz_full CPUs
nohz: Move idle balancer registration to the idle path
sched/loadavg: Generalize "_idle" naming to "_nohz"
sched/core: Drop the unused try_get_task_struct() helper function
sched/fair: WARN() and refuse to set buddy when !se->on_rq
sched/debug: Fix SCHED_WARN_ON() to return a value on !CONFIG_SCHED_DEBUG as well
sched/wait: Disambiguate wq_entry->task_list and wq_head->task_list naming
sched/wait: Move bit_wait_table[] and related functionality from sched/core.c to sched/wait_bit.c
sched/wait: Split out the wait_bit*() APIs from <linux/wait.h> into <linux/wait_bit.h>
sched/wait: Re-adjust macro line continuation backslashes in <linux/wait.h>
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Rework the EFI capsule loader to allow for workarounds for
non-compliant firmware (Ard Biesheuvel)
- Implement a capsule loader quirk for Quark X102x (Jan Kiszka)
- Enable SMBIOS/DMI support for the ARM architecture (Ard Biesheuvel)
- Add CONFIG_EFI_PGT_DUMP=y support for x86-32 and kexec (Sai
Praneeth)
- Fixes for EFI support for Xen dom0 guests running under x86-64
hosts (Daniel Kiper)"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen/efi: Initialize only the EFI struct members used by Xen
efi: Process the MEMATTR table only if EFI_MEMMAP is enabled
efi/arm: Enable DMI/SMBIOS
x86/efi: Extend CONFIG_EFI_PGT_DUMP support to x86_32 and kexec as well
efi/efi_test: Use memdup_user() helper
efi/capsule: Add support for Quark security header
efi/capsule-loader: Use page addresses rather than struct page pointers
efi/capsule-loader: Redirect calls to efi_capsule_setup_info() via weak alias
efi/capsule: Remove NULL test on kmap()
efi/capsule-loader: Use a cached copy of the capsule header
efi/capsule: Adjust return type of efi_capsule_setup_info()
efi/capsule: Clean up pr_err/_info() messages
efi/capsule: Remove pr_debug() on ENOMEM or EFAULT
efi/capsule: Fix return code on failing kmap/vmap
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWVpGxCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71SGMAKCP9mGjMWqD
Z9uCT8swDJ8LCi/o+wCfV4Cs0eWzqkJUDMaycdJrlMjB174=
=TavE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "late dt64 for 4.13" from Gregory CLEMENT:
It is actually a patch that missed the end of the 4.12 merge
window. The patch itself fix a bogus definition of the timer for the
Armada 37xx SoCs.
* tag 'mvebu-dt64-4.13-3' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Contrary to popular belief, PPIs connected to a GICv3 to not have
an affinity field similar to that of GICv2. That is consistent
with the fact that GICv3 is designed to accomodate thousands of
CPUs, and fitting them as a bitmap in a byte is... difficult.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
With the introduction of struct pci_host_bridge.map_irq pointer it is
possible to assign IRQs for all devices originating from a PCI host bridge
at probe time; this is implemented through pci_assign_irq() that relies on
the struct pci_host_bridge.map_irq pointer to map IRQ for a given device.
The benefits this brings are twofold:
- the IRQ for a device is assigned once at probe time
- the IRQ assignment works also for hotplugged devices
With all DT based PCI host bridges converted to the struct
pci_host_bridge.{map/swizzle}_irq hooks mechanism the DT IRQ allocation in
ARM64 pcibios_alloc_irq() is now redundant and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
This reverts commits 2c0cba482e ("arm: sun8i: sunxi-h3-h5: Add dt node
for the syscon control module") to 2428fd0fe5 ("arm64: defconfig: Enable
dwmac-sun8i driver on defconfig") and 3432a86e64 ("arm: sun8i:
orangepipc: use internal phy-mode") to 5a79b4f2a5 ("arm: sun8i:
orangepi-2: use internal phy-mode") that should be merged
through the arm-soc tree, and end up in merge conflicts and build failures.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct jit_ctx::image is used the store a pointer to the jitted
intructions, which are always little-endian. These instructions
are thus correctly converted from native order to little-endian
before being stored but the pointer 'image' is declared as for
native order values.
Fix this by declaring the field as __le32* instead of u32*.
Same for the pointer used in jit_fill_hole() to initialize
the image.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=6hNK
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.13
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
Conflicts:
arch/s390/include/asm/kvm_host.h
Now that compat_vfp_get() uses the regset API to copy the FPSCR
value out to userspace, compat_vfp_set() looks inconsistent. In
particular, compat_vfp_set() will fail if called with kbuf != NULL
&& ubuf == NULL (which is valid usage according to the regset API).
This patch fixes compat_vfp_set() to use user_regset_copyin(),
similarly to compat_vfp_get().
This also squashes a sparse warning triggered by the cast that
drops __user when calling get_user().
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
compat_vfp_set() checks for userspace trying to write an excessive
amount of data to the regset. However this check is conspicuous
for its absence from every other _set() in the arm64 ptrace
implementation. In fact, the core ptrace_regset() already clamps
userspace's iov_len to the regset size before the individual regset
.{get,set}() methods get called.
This patch removes the redundant check.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If get_user() fails when reading the new FPSCR value from userspace
in compat_vfp_get(), then garbage* will be written to the task's
FPSR and FPCR registers.
This patch prevents this by checking the return from get_user()
first.
[*] Actually, zero, due to the behaviour of get_user() on error, but
that's still not what userspace expects.
Fixes: 478fcb2cdb ("arm64: Debugging support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
get_alt_insn() is used to read and create ARM instructions, which
are always stored in memory in little-endian order. These values
are thus correctly converted to/from native order when processed
but the pointers used to hold the address of these instructions
are declared as for native order values.
Fix this by declaring the pointers as __le32* instead of u32* and
make the few appropriate needed changes like removing the unneeded
cast '(u32*)' in front of __ALT_PTR()'s definition.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In the flattened device tree format, all integer properties are
in big-endian order.
Here the property "kaslr-seed" is read from the fdt and then
correctly converted to native order (via fdt64_to_cpu()) but the
pointer used for this is not annotated as being for big-endian.
Fix this by declaring the pointer as fdt64_t instead of u64
(fdt64_t being itself typedefed to __be64).
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 implementation of ip_fast_csum() do most of the work
in 128 or 64 bit and call csum_fold() to finalize. csum_fold()
itself take a __wsum argument, to insure that this value is
always a 32bit native-order value.
Fix this by adding the sadly needed '__force' to cast the native
'sum' to the type '__wsum'.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This adds a Kconfig symbol for DTs and drivers being added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8Vxy
-----END PGP SIGNATURE-----
Merge tag 'actions-arm64-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/arm64
Pull "Actions Semi ARM64 SoC for v4.13" from Andreas Färber:
This adds a Kconfig symbol for DTs and drivers being added.
* tag 'actions-arm64-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
arm64: Prepare Actions Semi S900
Jagan Teki