Sink can be configured to calculate the CRC over the static frame and
compare with the CRC calculated and transmited in the VSC SDP by
source, if there is a mismatch sink will do a short pulse in HPD
and set DP_PSR_LINK_CRC_ERROR in DP_PSR_ERROR_STATUS.
Spec: 7723
v6:
andling DP_PSR_LINK_CRC_ERROR here and remove "bdw+" from commit
message
v4:
patch moved to after 'drm/i915/psr: Avoid PSR exit max time timeout'
to avoid touch in 2 patches EDP_PSR_DEBUG.
v3:
disabling PSR instead of exiting on error
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-5-jose.souza@intel.com
Alpha blending with alpha 0 and 0xff passes through
alpha math and rounding logic causing differences
compared to fully transparent or opaque plane,resulting
in CRC mismatch.
This WA on icl and above enables hardware to bypass alpha
math and rounding for per pixel alpha values of 00 and 0xff
v2: Fix patchwork checkpatch warnings.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1529594036-25036-1-git-send-email-vandita.kulkarni@intel.com
Some MG PLL registers have fields that need to be preserved at their HW
default or BIOS programmed values. So make sure we preserve them.
v2:
- Add comment to icl_mg_pll_write() explaining the need for register
masks. (Vandita)
- Fix patchwork checkpatch warning.
v3:
- Rebase on drm-tip.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v1)
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180619164115.7835-1-imre.deak@intel.com
This patch enables hotplug interrupts for DP over TBT output on TC
ports. The TBT interrupts are enabled and handled irrespective of the
actual output type which could be DP Alternate, DP over TBT, native DP
or native HDMI.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-3-paulo.r.zanoni@intel.com
The hotplug interrupts for the ports can be routed to either North
Display or South Display depending on the output mode. DP Alternate or
DP over TBT outputs will have hotplug interrupts routed to the North
Display while interrupts for legacy modes will be routed to the South
Display in PCH. This patch adds hotplug interrupt handling support for
DP Alternate mode.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: coding style changes]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-2-paulo.r.zanoni@intel.com
The Graphics System Event(GSE) interrupt bit has a new location in the
GU_MISC_INTERRUPT_{IIR, ISR, IMR, IER} registers. Since GSE was the only
DE_MISC interrupt that was enabled, with this change we don't enable/handle
any of DE_MISC interrupts for gen11. Credits to Paulo for pointing out
the register change.
v2: from DK
raw_reg_[read/write], branch prediction hint and drop platform check (Mika)
v3: From DK
Early re-enable of master interrupt (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
[Paulo: bikesheds and rebases]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180616000530.5357-1-paulo.r.zanoni@intel.com
Since I'm touching the file I might as well fix this class of errors
since they are just a few. Also drive-by fix the styling of the
VLV_TURBO_SOC_OVERRIDE definitions instead of just the spaces before
the tabs.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612235654.7914-3-paulo.r.zanoni@intel.com
Because OCD.
Now seriously, commit 1aa920ea0e ("drm/i915: add register macro
definition style guide") has finally established a coding standard to
be followed by the rest of the file, and I've been trying to request
everybody to adhere to that since then. The problem is that when
someone adds a new line to a register that has the wrong style, these
people generally propagate the wrong style and I have to keep asking
them to drive-by fix the whole register, which is not something I like
to do and also creates extra work for them. Or I can ignore the
propagation of the wrong coding style and feel anxious about it. On
top of that, we now have our CI happily reminding us about these
problems, which makes everything worse.
So IMHO the best way to proceed is to fix the spacing issues in the
file once and for all. Contributors will stop propagating the bad
style when adding new bits to registers that already have bad style,
we will stop asking them to redo their patches and the CI emails will
become more relevant by having less semi-false errors.
Yes, there will be some pain involved for backporters, but at least
spacing issues like that are easy to spot and fix in the patch files.
This patch was generated by:
../../../../scripts/checkpatch.pl -f --strict --types SPACING \
--fix-inplace i915_reg.h
I manually checked the output and everything seems sane.
v2: Single conflict around the addition of DP_TP_CTL_LINK_TRAIN_PAT4.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618180943.894-1-paulo.r.zanoni@intel.com
Having the w/a registers as an open-coded table leaves a trap for the
unwary; it would be easy to miss incrementing the LRI counter when
adding a new register to the list. Instead, pull the list of registers
into a table, so that we only need add new registers to that table
rather than try and remember important side-effects of earlier chunks of
GPU instructions.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180618094150.30895-1-chris@chris-wilson.co.uk
The SF and clipper units mishandle the provoking vertex in some cases,
which can cause misrendering with shaders that use flat shaded inputs.
There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN
(for the clipper) that work around the issue. These registers are
unfortunately not part of the logical context (even the power context),
and so we must reload them every time we start executing in a context.
Bugzilla: https://bugs.freedesktop.org/103047
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
DP spec 1.4 supports training pattern set 4 (TPS4) for HBR3 link
rate. This will be used in link training's channel equalization
phase if supported by both source and sink.
This patch adds the helpers to check if HBR3 is supported and uses
TPS4 in training pattern selection during link training.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-2-paulo.r.zanoni@intel.com
Add support for DP_AUX_E. Here we also introduce the bits for the AUX
power well E, however ICL power well support is still not enabled yet,
so the power well is not used.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-2-paulo.r.zanoni@intel.com
There is a problem with kbl up to rev E0 where a heavy
memory/fabric traffic from adjacent engine(s) can cause an engine
reset to fail. This traffic can be from normal memory accesses
or it can be from heavy polling on a semaphore wait.
For engine hogging causing a fail, we already fallback to
full reset. Which effectively stops all engines and thus
we only add a workaround documentation.
For the semaphore wait loop poll case, we add one microsecond
poll interval to semaphore wait to guarantee bandwidth for
the reset preration. The side effect is that we make semaphore
completion latencies also 1us longer.
v2: Let full reset handle the adjacent engine idling (Chris)
v3: Skip render engine (Joonas), please checkpatch on define (Mika)
References: https://bugs.freedesktop.org/show_bug.cgi?id=106684
References: VTHSD#2227190, HSDES#1604216706, BSID#0917
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607172444.17080-1-mika.kuoppala@linux.intel.com
PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
This gets a little tricky for ICL since there is
no register bit that maps directly to the link clock.
So this patch creates a separate function in intel_dpll_mgr.c
to obtain the write array PLL Params and compares the set
pll_params with the table to get the corresponding link
clock.
v2:
- Fix the encoder type check (DK).
- Improve our error checking, return a sane value (Mika, Paulo).
- Fix table entries (Paulo).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Paulo: implement v2]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523224444.19017-1-paulo.r.zanoni@intel.com
DFLEXDPMLE register is required to tell the FIA hardware which
main links of DP are enabled on TCC Connectors. FIA uses this
information to program PHY to Controller signal mapping.
This register is applicable in both TC connector's Alternate mode
as well as DP connector mode.
v2:
* Remove _ICL prefix since the reg is first introduced
in ICL (Paulo)
* s/ICL/icl in commit message (Lucas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527275032-4555-1-git-send-email-manasi.d.navare@intel.com
Set up the SKL+ scaler initial phase registers correctly. Otherwise
we start fetching the data from the center of the first pixel instead
of the top-left corner, which obviously then leads to right/bottom edges
replicating data excessively as the data runs out half a pixel too soon.
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180521185613.5097-2-ville.syrjala@linux.intel.com
Reviewed-By: Vidya Srinivas <vidya.srinivas@intel.com>
Use MCURSOR_ instead of CURSOR_ as the prefix for the non-845/865
cursor defines consistently, and move the pipe CSC enable bit next
to the other non-845/865 cursor defines.
v2: Take care of gvt uses as well
v3: Another gvt use popped up
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131143709.875-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com> #v2
Like we do for encoder let's make the plane->get_hw_state() return
the pipe to which the plane is currently attached. We don't currently
allow planes to move between the pipes, but perhaps one day we will.
In either case this makes the code more uniform and perhaps makes
intel_plane_mapping_ok() slightly more clear.
Note that for i965 and g4x planes A and B still have pipe select bits
but they're hardwired to pipe A and B respectively. This means we can
safely interpret those bits just like on gen2/3. This allows the
same readout code work for plane C (which can still be assigned
to eiter pipe on i965) should we ever expose it.
g4x no longer allows moving the cursor planes between the pipes,
but the pipe select bits can still be set in the register. Thus
we have to ignore those bits. OTOH i965 still allows the cursors
to move between pipes thus we have to trust the bits there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130203807.13721-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Enables blend optimization for floating point RTs
v2: Rebased on top of the WA refactoring
v3: Added References (Mika)
References: HSDES#1406393558
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527285939-20113-5-git-send-email-oscar.mateo@intel.com
Disable blend embellishment in RCC.
Also, some other registers style fixed in passing.
v2: Rebased on top of the WA refactoring
v3: Added References (Mika)
v4:
- Fixed in B0
- Mentioned style fixes in commit message
References: HSDES#2006665173
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527285939-20113-4-git-send-email-oscar.mateo@intel.com
Redirects the state cache to the CS Command buffer section for
performance reasons.
v2: Rebased
v3: Rebased on top of the WA refactoring
v3: Added References (Mika)
References: HSDES#1604325460
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527285939-20113-3-git-send-email-oscar.mateo@intel.com
Revert to the legacy implementation.
v2: GEN7_ROW_CHICKEN2 is masked
v3:
- Rebased
- Renamed to Wa_2006611047
- A0 and B0 only
v4:
- Add spaces around '<<' (and fix the surrounding code as well)
- Mark the WA as pre-prod
v5: Rebased on top of the WA refactoring
v6: Added References (Mika)
v7: Fixed in B0
References: HSDES#2006611047
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527285939-20113-2-git-send-email-oscar.mateo@intel.com
For psr block #9, the vbt description has moved to options [0-3] for
TP1,TP2,TP3 Wakeup time from decimal value without any change to vbt
structure. Since spec does not mention from which VBT version this
change was added to vbt.bsf file, we cannot depend on bdb->version check
to change for all the platforms.
There is RCR inplace for GOP team to provide the version number
to make generic change. Since Kabylake with bdb version 209 is having this
change, limiting this change to gen9_bc and version 209+ to unblock google.
Tested on skl(bdb version 203,without options) and
kabylake(bdb version 209,212) having new options.
bspec 20131
v2: (Jani and Rodrigo)
move the 165 version check to intel_bios.c
v3: Jani
Move the abstraction to intel_bios.
v4: Jani
Rename tp*_wakeup_time to have "us" suffix.
For values outside range[0-3],default to max 2500us.
Old decimal value was wake up time in multiples of 100us.
v5: Jani and Rodrigo
Handle option 2 in default condition.
Print oustide range value.
For negetive values default to 2500us.
v6: Jani
Handle default first and then fall through for case 2.
v7: Rodrigo
Apply this change for IS_GEN9_BC and vbt version > 209
v8: Puthik
Add new function vbt_psr_to_us.
v9: Jani
Change to v7 version as it's more readable.
DK
add comment /*fall through*/ after case2.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Puthikorn Voravootivat <puthik@chromium.org>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526981243-2745-1-git-send-email-vathsala.nagaraju@intel.com
L3Bank could be fused off in hardware for debug purpose, and it
is possible that subslice is enabled while its corresponding L3Bank pairs
are disabled. In such case, if MCR packet control register(0xFDC) is
programed to point to a disabled bank pair, a MMIO read into L3Bank range
will return 0 instead of correct values.
However, this is not going to be the case in any production silicon.
Therefore, we only check at initialization and issue a warning should
this really happen.
References: HSDES#1405586840
v2:
- use fls instead of find_last_bit (Chris)
- use is_power_of_2() instead of counting bit set (Chris)
v3:
- rebase on latest tip
v5:
- Added references (Mika)
- Move local variable into scope where they are used (Ursulin)
- use a new local variable to reduce long line of code (Ursulin)
v6:
- Some coding style and use more local variables for clearer
logic (Ursulin)
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Yunwei Zhang <yunwei.zhang@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1526683285-24861-1-git-send-email-yunwei.zhang@intel.com
Clean up the DP pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state(),
the port state asserts, and the VLV power sequencer code.
v2: Return PIPE_A for cpt/ppt when the port isn't selected by
any transcoder. Returning INVALID_PIPE explodes *somewhere*
on some machines (can't immediately see where though). This
now matches the old behaviour.
v3: Order the defines shift,mask,value (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518152931.13104-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Parametrize the DVO pipe select bits.
For consistency with the new way of doing things, let's read out the
pipe select bits even when the port is disable, even though we don't
need that behaviour for asserts in this case.
v2: Order the defines shift,mask,value (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180514172423.9302-5-ville.syrjala@linux.intel.com
Parametrize the TV pipe select bits.
For consistency with the new way of doing things, let's read out the
pipe select bits even when the port is disable, even though we don't
need that behaviour for asserts in this case.
v2: Order the defines shift,mask,value (Jani)
Clear the stale pipe select bit in load detection (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180514172423.9302-4-ville.syrjala@linux.intel.com
Clean up the SDVO pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state()
and the port state asserts.
v2: Order the defines shift,mask,value (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180514172423.9302-3-ville.syrjala@linux.intel.com
Clean up the LVDS pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state()
and the port state asserts.
v2: Order the defines shift,mask,value (Jani)
Drop ruperfluous braces and whitesapce changes (Jani)
Combine masks in compute_is_dual_link_lvds() (Jani)
v3: Fix LVDS_PIPE_SEL_MASK_CPT
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180514182827.28629-1-ville.syrjala@linux.intel.com
Clean up the ADPA pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state()
and the port state asserts.
v2: Order the defines shift,mask,value (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180514172423.9302-1-ville.syrjala@linux.intel.com
Avoids a hang during soft reset.
v2: Rebased on top of the WA refactoring
v3: Added References (Mika)
v4:
- Rebased
- C, not lisp (Chris)
- Which steppings affected by this are not clear.
For the moment, apply unconditionally as per the
BSpec (Mika)
- Add reference to another HSD also related
References: HSDES#1405476379
References: HSDES#2006612137
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-14-git-send-email-oscar.mateo@intel.com
Disable CGPSF unit clock gating to prevent an issue.
v2: Rebased on top of the WA refactoring
v3: Added References (Mika)
v4:
- Rebased
- C, not lisp (Chris)
- Remove unintentional whitespaces (Mika)
- Fixed in C0 (Mika)
References: HSDES#1406838659
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-13-git-send-email-oscar.mateo@intel.com
Disable I2M Write for performance reasons.
v2: Rebased on top of the WA refactoring
v3: Added References (Mika)
v4:
- Rebased
- C, not lisp (Chris)
- GEN7 chicken bit in the wrong side of the fence (Mika)
- Use two spaces to align bit macros
References: HSDES#1604302699
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-12-git-send-email-oscar.mateo@intel.com
Disable MSC clock gating to prevent data corruption.
BSpec: 19257
v2: Rebased on top of the WA refactoring
v3: Added References (Mika)
v4:
- Rebased
- C, not lisp (Chris)
- A0 only (Mika)
References: HSDES#1405779004
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-10-git-send-email-oscar.mateo@intel.com
Revert to the legacy implementation to avoid a system hang.
v2: Correct the address for GAMW_ECO_DEV_RW_IA_REG
v3: Renamed to Wa_220166154
v4: Rebased on top of the WA refactoring
v5: Added References (Mika)
v6:
- Rebased
- C, not lisp (Chris)
References: HSDES#220166154
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-9-git-send-email-oscar.mateo@intel.com
This workarounds an issue with insufficient storage for the
CL2 and SF units.
v2: Renamed to Wa_1405766107
v3: Wrapped the commit message
v4: Rebased on top of the WA refactoring
v5: Added References (Mika)
v6:
- Rebased
- s/MACALLOC/MAXALLOC (Mika)
- C, not lisp (Chris)
References: HSDES#1405766107
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-8-git-send-email-oscar.mateo@intel.com
Avoids an undefined LLC behavior.
BSpec: 9613
v2: Renamed to Wa_1405733216
v3: Spaces around '<<' and fix surrounding code
v4: Rebased on top of the WA refactoring
v5: Added References (Mika)
v6:
- Rebased
- C, not lisp (Chris)
References: HSDES#1405733216
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-7-git-send-email-oscar.mateo@intel.com
Adjust default GAM TLB partitioning for performance reasons.
v2: Only touch the bits that we really need
v3: Rebased on top of the WA refactoring
v4:
- Added References (Mika)
- Rebased
v5:
- Rebased
- C, not lisp (Chris)
- Correct reference number (Mika)
References: HSDES#220160670
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-6-git-send-email-oscar.mateo@intel.com
Revert to an L3 non-hash model, for performance reasons.
v2:
- Place the WA name above the actual change
- Improve the register naming
v3:
- Rebased
- Renamed to Wa_1604223664
v4: Rebased on top of the WA refactoring
v5:
- Added References (Mika)
- Fixed wrong mask and value (Mika)
- Do not apply together with another WA for the same
register (not worth the hassle)
v6:
- Rebased
- C, not lisp (Chris)
References: HSDES#1604223664
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-5-git-send-email-oscar.mateo@intel.com
The default GAPZ arbitrer priority value at power-on has been found
to be incorrect.
v2: Now renamed to Wa_1405543622
v3: Rebased on top of the WA refactoring
v4: Added HSDES reference number (Mika)
v5:
- Rebased
- C, not lisp (Chris)
References: HSDES#1405543622
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-4-git-send-email-oscar.mateo@intel.com
Sampler Dynamic Frequency Rebalancing (DFR) aims to reduce Sampler
power by dynamically changing its clock frequency in low-throughput
conditions. This patches enables it by default on Gen11.
v2: Wrong operation to clear the bit (Praveen)
v3: Rebased on top of the WA refactoring
v4: Move to icl_init_clock_gating, since it's not a WA (Rodrigo)
v5: C, not lisp (Chris)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Praveen Paneri <praveen.paneri@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-3-git-send-email-oscar.mateo@intel.com
Inherit workarounds from previous platforms that are still valid for
Icelake.
v2: GEN7_ROW_CHICKEN2 is masked
v3:
- Since it has been fixed already in upstream, removed the TODO
comment about WA_SET_BIT for WaInPlaceDecompressionHang.
- Squashed with this patch:
drm/i915/icl: add icelake_init_clock_gating()
from Paulo Zanoni <paulo.r.zanoni@intel.com>
- Squashed with this patch:
drm/i915/icl: WaForceEnableNonCoherent
from Oscar Mateo <oscar.mateo@intel.com>
- WaPushConstantDereferenceHoldDisable is now Wa_1604370585 and
applies to B0 as well.
- WaPipeControlBefore3DStateSamplePattern WABB was being applied
to ICL incorrectly.
v4:
- Wrap the commit message
- s/dev_priv/p to please checkpatch
v5: Rebased on top of the WA refactoring
v6: Rebased on top of further whitelist registers refactoring (Michel)
v7: Added WaRsForcewakeAddDelayForAck
v8: s/ICL_HDC_CHICKEN0/ICL_HDC_MODE (Mika)
v9:
- C, not lisp (Chris)
- WaIncreaseDefaultTLBEntries is the same for GEN > 9_LP (Tvrtko)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-2-git-send-email-oscar.mateo@intel.com
In Icelake, there are more engines on which Memory Object Control
States need to be configured. Besides adding Icelake under Skylake
config, the patch makes sure MOCS register addresses for the new
engines are properly defined.
Additional patch might be need later, in case the specification will
propose different MOCS config values for Icelake than in previous
gens.
v2: Restricted comments to gen11, updated description, renamed
defines.
v3: Used proper engine indexes for gen11.
v4: Ensure patch is Icelake only.
v5: Style fixes (proposed by mwajdeczko)
v6 (from Paulo): fix checkpatch's COMMIT_LOG_LONG_LINE (Checkpatch).
BSpec: 19405
BSpec: 21140
Cc: Oscar Mateo Lozano <oscar.mateo@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502223142.3891-1-paulo.r.zanoni@intel.com
There's a lot of code for the PLL enabling, so let's first only
introduce the register definitions in order to make patch reviewing a
little easier.
v2: Coding style (Jani).
v3: Preparation for upstreaming.
v4: Fix MG_CLKTOP2_CORECLKCTL1 address and random typos (James).
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-3-paulo.r.zanoni@intel.com
Gen11/ICL onward ddb entry start/end mask is increased from 10 bits to
11 bits. This patch make changes to use proper mask for ICL+ during
hardware ddb value readout.
Changes since V1:
- Use _MASK & _SHIFT macro (James)
Changes since V2:
- use kernel type u8 instead of uint8_t
Changes since V3:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-4-mahesh1.kumar@intel.com
These fields have been deprecated and moved in ICL+. Stop setting the
bits.
They have moved to GAMMA_MODE and CSC_MODE, respectively. This patch
is just to stop incorrectly setting bits in PLANE_COLOR_CTL while
we're waiting for the new replacement functionality to be done.
v2: Drop useless comment, and change !(GEN >= 11) to (GEN < 11). (Ville)
v3: No changes
v4 (from Paulo): Rebase.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-2-paulo.r.zanoni@intel.com
This will be helpful to debug what hardware is actually tracking
and causing PSR to exit.
BSpec: 7721
v4:
- Using _MMIO_TRANS2() in PSR_EVENT
- Cleaning events before printing
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180425212334.21109-2-jose.souza@intel.com
Plug in the bdw+ irq handling for PSR interrupts. bdw+ supports psr on
any transcoder in theory, though the we don't currenty enable PSR except
on the EDP transcoder.
v2: From DK
* Rebased on drm-tip
v3: Switched author to Ville based on IRC discussion.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403212420.25007-2-dhinakaran.pandiyan@intel.com
The definitions for the error register should be valid on bdw/skl too,
but there we haven't even enabled DE_MISC handling yet.
Somewhat confusing the the moved register offset on bdw is only for
the _CTL/_AUX register, and that _IIR/IMR stayed where they have been
on bdw.
v2: Fixes from Ville.
v3: From DK
* Rebased on drm-tip
* Removed BDW IIR bit definition, looks like an unintentional change that
should be in the following patch.
v4: From DK
* Don't mask REG_WRITE.
References: bspec/11974 [SRD Interrupt Bit Definition DevHSW]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405220023.9449-1-dhinakaran.pandiyan@intel.com
This patch sets appropriate scaler mode for NV12 format.
In this mode, skylake scaler does either chroma-upsampling or
chroma-upsampling and resolution scaling
v2: Review comments from Ville addressed
NV12 case to be checked first for setting
the scaler
v3: Rebased (me)
v4: Rebased (me)
v5: Missed the Tested-by/Reviewed-by in the previous series
Adding the same to commit message in this version.
v6: Rebased (me)
v7: Rebased (me)
v8: Rebased (me)
Restricting the NV12 change for scaler to BXT and KBL
in this series.
v9: Rebased (me)
v10: As of now, NV12 has been tested on Gen9 and Gen10. However,
code is applicable to all GEN >= 9. Hence making
that change to keep it generic.
Comments under v8 is not valid anymore.
v11: Addressed review comments by Shashank Sharma.
For Gen10+, the scaler mode to be set it planar or normal
(single bit). Changed the code to be applicable to all
Gen.
v12: Addressed review comments from Shashank Sharma
For Gen9 (apart from GLK) bits 28:29 to be programmed
in PS_CTRL for NV12. For GLK and Gen10+, bit 29 to be set
for all Planar.
v13: Addressed review comments from Juha-Pekka Heikkila
"NV12 not to be supported by SKL"
Adding Reviewed by tag from Shashank Shamr
v14: Added reviewed by from Juha-Pekka Heikkila
v15: Rebased the series
Tested-by: Clinton Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-13-git-send-email-vidya.srinivas@intel.com
Display WA 827 applies to GEN9 (excluede GLK) and CNL.
Switching the plane format from NV12 to RGB and leaving system idle
results in display underrun and corruption.
WA: Set the bit 15 & bit 19 to 1b in the CLKGATE_DIS_PSL
register for the pipe in which NV12 plane is enabled.
v2: Addressed review comments from Maarten and
Juha-Pekka Heikkila. Added reviewed by from
Juha-Pekka Heikkila.
v3: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-11-git-send-email-vidya.srinivas@intel.com
Using the new hierarchical interrupt infrastructure.
v2: Rebase
v3: Rebase
v4: use class/instance handler (Mika)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-3-mika.kuoppala@linux.intel.com
Interrupt identity register we already read from hardware
contains engine class and instance fields. Leverage
these fields to find correct engine to handle the interrupt.
v3: rebase on top of rps intr
use correct class / instance limits (Michel)
v4: split engine/other handling
v5: empty iir is not err (Daniele, Michel)
Suggested-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180406093145.14389-1-mika.kuoppala@linux.intel.com
The bits used to reset the different engines/domains have changed in
GEN11, this patch maps the reset engine mask bits with the new bits
in the reset control register.
v2: Use shift-left instead of BIT macro to match the file style (Paulo).
v3: Reuse gen8_reset_engines (Daniele).
v4: Do not call intel_uncore_forcewake_reset after reset, we may be
using the forcewake to read protected registers elsewhere and those
results may be clobbered by the concurrent dropping of forcewake.
bspec: 19212
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-1-mika.kuoppala@linux.intel.com
Commit 'aee3bac0a3a8 ("drm/i915/psr: Tie PSR2 support to Y
coordinate requirement")' got merged to drm-intel-next-queued
but the variable was defined commit 'c5fe47327b06 ("drm: Add PSR
version 3 macro") who was merged through drm-misc.
So backmerging to get drm-intel-next-queued compiling back again.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
For Geminilake and Cannonlake+ the Y-coordinate support must be
enabled in PSR2_CTL too.
Spec: 7713 and 7720
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328223046.16125-5-jose.souza@intel.com
The only thing that differs here is that the crystal clock freq now
has four possible values.
This patch gets rid of the "Unknown gen, unable to compute..." message
at boot for gen11.
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109232835.11478-18-paulo.r.zanoni@intel.com
Protect the macro parameters with parens in order to avoid priority
issues on macro evaluation when the macro argument is not a single
operand.
This is not a problem today, but it could be in the future. I found
this while reviewing a patch that introduces new callers for the
macros.
v2: Rebase.
Reference: commit 04416108cc ("drm/i915/cnl: Add registers related to voltage swing sequences.")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323195853.4599-1-paulo.r.zanoni@intel.com
On Icelake platform, MG PHY is used when operating in DP alternate
mode or the legacy HDMI or DP modes. DDI Ports C, D, E, F are MG PHY
DDI ports on ICL.
This patch adds the necessary voltage swing programming related
register definitions and macros for MG PHY DDI ports.
v4 (from Paulo):
* Use _PORT instead of _PICK
* Change some mask names to our current coding standards
* Stay under 80 columns
v3:
* Rebase on new revision of patches
v2:
* Remove whitespaces in the #defines (Paulo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323172419.24911-4-paulo.r.zanoni@intel.com
This patch defines register definitions required for ICL voltage
vswing programming for Combo PHY DDI Ports. It uses the same bit
definitions and macros as the CNL voltage swing sequences.
v8 (from Paulo):
* Rebase.
v7:
* Kill _MMIIO_PORT2_LN (Paulo)
v6:
* Replace some spaces with TAB (Paulo)
v5:
* Use _PORT instead of _PICK (Paulo)
* Remove DW7 defs for ICL, not used (Paulo)
v4:
* Rebase after _PICK was used instead of _PORT3
* Use _PICK for _MMIO_PORT2 since address of B is less
than address of A so cant use the math (Paulo)
v3:
* Make changes to the existing macro in a diff patch (Paulo)
v2:
* Add new defs fro ICL regs (Paulo)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323172419.24911-2-paulo.r.zanoni@intel.com
HSW and BDW have SRD_AUX_{CTL, STATUS} registers that the driver needs to
setup for the HW to use whenever exiting PSR. SKL+ hardware use hardcoded
values for the same and do not need any registers to be setup. So, use
drm_dp_dpcd_writeb() for a one-time write during PSR enable and setup the
PSR aux registers on HSW and BDW for later use by HW.
We also end up writing to reserved bits in SRD_AUX_CTL by reusing
intel_dp->get_aux_send_ctl() for HSW and BDW, fix this.
Since the AUX register setup is source side programming, move the call
to enable_source() from enable_sink().
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313034646.3721-2-dhinakaran.pandiyan@intel.com
This patch adds support to detect ICL, slice, subslice and EU fuse
settings.
Add addresses for ICL 11 slice, subslice and EU fuses registers.
These register addresses are the same as previous platforms but the
format and / or the meaning of the information is different. Therefore
Gen11 defines for these registers are added.
Bspec: 9731
Bspec: 20643
Bspec: 20673
v2: Update fusing information storage after introducing the new query
uAPI (Lionel)
v3 (Oscar):
- The maximum number of slices in ICL 11 is 1
- The subslice disable fuse can potentially store information in
all bits
- GEN_MAX_SUBSLICES has to be increased to 8
- Don't trust the slice enabled fuse outside the max number of
expected slices
- Indentation fix and some reordering and renaming of local
variables
v4: Use single space after Cc tag
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1521575121-9577-1-git-send-email-oscar.mateo@intel.com
ICL 11 has a greater number of maximum subslices. This patch
reflects this.
v2: GEN11 updates to MCR_SELECTOR (Oscar)
v3: Copypasta error in the new defines (Lionel)
Bspec: 21139
BSpec: 21108
Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com> (v1)
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-3-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
In Gen11, the Video Decode engines (aka VDBOX, aka VCS, aka BSD) and the
Video Enhancement engines (aka VEBOX, aka VECS) could be fused off. Also,
each VDBOX and VEBOX has its own power well, which only exist if the
related engine exists in the HW.
Unfortunately, we have a Catch-22 situation going on: we need the blitter
forcewake to read the register with the fuse info, but we cannot initialize
the forcewake domains without knowin about the engines present in the HW.
We workaround this problem by allowing the initialization of all forcewake
domains and then pruning the fused off ones, as per the fuse information.
Bspec: 20680
v2: We were shifting incorrectly for vebox disable (Vinay)
v3: Assert mmio is ready and warn if we have attempted to initialize
forcewake for fused-off engines (Paulo)
v4:
- Use INTEL_GEN in new code (Tvrtko)
- Shorter local variable (Tvrtko, Michal)
- Keep "if (!...) continue" style (Tvrtko)
- No unnecessary BUG_ON (Tvrtko)
- WARN_ON and cleanup if wrong mask (Tvrtko, Michal)
- Use I915_READ_FW (Michal)
- Use I915_MAX_VCS/VECS macros (Michal)
v5: Rebased by Rodrigo fixing conflicts on top of:
"drm/i915: Simplify intel_engines_init"
v6: Fix v5. Remove info->num_rings. (by Oscar)
v7: Rebase (Rodrigo).
v8:
- s/intel_device_info_fused_off_engines/
intel_device_info_init_mmio (Chris)
- Make vdbox_disable & vebox_disable local variables (Chris)
v9:
- Move function declaration to intel_device_info.h (Michal)
- Missing indent in bit fields definitions (Michal)
- When RC6 is enabled by BIOS, the fuse register cannot be read until
the blitter powerwell is awake. Shuffle where the fuse is read, prune
the forcewake domains after the fact and change the commit message
accordingly (Vinay, Sagar, Chris).
v10:
- Improved commit message (Sagar)
- New line in header file (Sagar)
- Specify the message in fw_domain_reset applies to ICL+ (Sagar)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-1-mika.kuoppala@linux.intel.com
[Mika: soothe checkpatch on commit msg]
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
AFAIK CHV was supposed to have HBR2 originally, but in the end the feature
was dropped. We still have some code leftovers from those early days.
Eliminate them.
The extra bit for the training pattern seems to be dead in the hardware.
I can set it (in fact I can set almost any reserved bit in the
registers) but it doesn't seem to interfere with the operation of the
hardware. Either that or I'm very lucky that my displays complete link
training with the incorrect pattern being sent out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302095656.19662-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
This patch creates a new macro to get PORT_TX register for any given DW.
This removes the need of defining register address for each port & DW.
Changes since V1:
- Use underscope prefix, as macro isn't returning an mmio reg(Lucas)
- Merge patch 1 & 2 of the series
Changes since V2:
- remove _MMIO_PORT6_LN macro (Rodrigo)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080653.9444-2-mahesh1.kumar@intel.com
UAPI Changes:
- Query uAPI interface (used for GPU topology information currently)
* Mesa: https://patchwork.freedesktop.org/series/38795/
Driver Changes:
- Increase PSR2 size for CNL (DK)
- Avoid retraining LSPCON link unnecessarily (Ville)
- Decrease request signaling latency (Chris)
- GuC error capture fix (Daniele)
* tag 'drm-intel-next-2018-03-08' of git://anongit.freedesktop.org/drm/drm-intel: (127 commits)
drm/i915: Update DRIVER_DATE to 20180308
drm/i915: add schedule out notification of preempted but completed request
drm/i915: expose rcs topology through query uAPI
drm/i915: add query uAPI
drm/i915: add rcs topology to error state
drm/i915/debugfs: add rcs topology entry
drm/i915/debugfs: reuse max slice/subslices already stored in sseu
drm/i915: store all subslice masks
drm/i915/guc: work around gcc-4.4.4 union initializer issue
drm/i915/cnl: Add Wa_2201832410
drm/i915/icl: Gen11 forcewake support
drm/i915/icl: Add Indirect Context Offset for Gen11
drm/i915/icl: Enhanced execution list support
drm/i915/icl: new context descriptor support
drm/i915/icl: Correctly initialize the Gen11 engines
drm/i915: Assert that the request is indeed complete when signaled from irq
drm/i915: Handle changing enable_fbc parameter at runtime better.
drm/i915: Track whether the DP link is trained or not
drm/i915: Nuke intel_dp->channel_eq_status
drm/i915: Move SST DP link retraining into the ->post_hotplug() hook
...
What was called SRD_DEBUG(0x6F860) on HSW and BDW was renamed to PSR_MASK
SKL onwards, add a note next to the macro definition.
There is also a different PSR_DEBUG on SKL+ to add to the confusion.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313040954.6289-1-dhinakaran.pandiyan@intel.com
No functional change. But let's keep definitions clean
and cursor related register definitions together.
v2: Fix caps x no caps on same reg. Change name to match
original reg name. (by Ville).
Also fix name on code s/surlive/surflive and on subject
s/cur_surlife/cur surflive/.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312210528.7905-1-rodrigo.vivi@intel.com
WA 0884:bxt:all,cnl:*:A - "When FBC is enabled with eDP PSR,
the CPU host modify writes may not get updated on the Display
as expected.
WA: Write 0x00000000 to CUR_SURFLIVE_A with every CPU
host modify write to trigger PSR exit."
We can also find on spec other cases where they describe
bogus writes to cursor registers to force PSR exit with
HW tracking. And it was confirmed by HW engineers that
this Wa can be safely applied for any frontbuffer activity.
So let's use this more and more here instead of forcibly
disable and re-enable PSR everytime that we have a simple
reliable flush case.
Other commits improve the fbcon/fbdev use a lot, but this
approach is the only when where we can get a fully reliable
console with no slowness or missed frames and PSR still
enabled and active.
v2: - Rebase on drm-tip
- (DK) Add a comment to explain that WA
tells about writing 0 to CUR_SURFLIVE_A but we write to
CUR_SURFLIVE(pipe).
v3: Wa doesn't work on PSR2.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309005218.26772-1-rodrigo.vivi@intel.com
"Clock gating bug in GWL may not clear barrier state when an EOT
is received, causing a hang the next time that barrier is used."
HSDES: 2201832410
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307220912.3681-1-rodrigo.vivi@intel.com
The main difference with previous GENs is that starting from Gen11
each VCS and VECS engine has its own power well, which only exist
if the related engine exists in the HW.
The fallback forcewake request workaround is only needed on gen9
according to the HSDES WA entry (1604254524), so we can go back to using
the simpler fw_domains_get/put functions.
BSpec: 18331
v2: fix fwtable, use array to test shadow tables, create new
accessors to avoid check on every access (Tvrtko)
v3 (from Paulo): Rebase.
v4:
- Range 09400-097FF should be FORCEWAKE_ALL (Daniele)
- Use the BIT macro for forcewake domains (Daniele)
- Add a comment about the range ordering (Oscar)
- Updated commit message (Oscar)
v5: Rebased
v6: Use I915_MAX_VCS/VECS (Michal)
v7: translate FORCEWAKE_ALL to available domains
v8: rebase, add clarification on fallback ack in commit message.
v9: fix rebase issue, change check in fw_domains_init from IS_GEN11
to GEN >= 11
v10: Generate is_genX_shadowed with a macro (Daniele)
Include gen11_fw_ranges in the selftest (Michel)
v11: Simplify FORCEWAKE_ALL, new line between NEEDS_FORCEWAKEs (Tvrtko)
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302161501.28594-6-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Starting from Gen11 the context descriptor format has been updated in
the HW. The hw_id field has been considerably reduced in size and engine
class and instance fields have been added.
There is a slight name clashing issue because the field that we call
hw_id is actually called SW Context ID in the specs for Gen11+.
With the current size of the hw_id field we can have a maximum of 2k
contexts at any time, but we could use the sw_counter field (which is sw
defined) to increase that because the HW requirement is that
engine_id + sw id + sw_counter is a unique number.
GuC uses a similar method to support more contexts but does its tracking
at lrc level. To avoid doing an implementation that will need to be
reworked once GuC support lands, defer it for now and mark it as TODO.
v2: rebased, add documentation, fix GEN11_ENGINE_INSTANCE_SHIFT
v3: rebased, bring back lost code from i915_gem_context.c
v4: make TODO comment more generic
v5: be consistent with bit ordering, add extra checks (Chris)
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302161501.28594-3-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Gen11 has up to 4 VCS and up to 2 VECS engines, this patch adds mmio
base definitions for all of them.
Bspec: 20944
Bspec: 7021
v2: Set the correct mmio_base in intel_engines_init_mmio; updating the
base mmio values any later would cause incorrect reads in
i915_gem_sanitize (Michel).
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ceraolo Spurio, Daniele <daniele.ceraolospurio@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302161501.28594-2-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Add support for the COLOR_RANGE property on planes. This property
selects whether the input YCbCr data is to treated as limited range
or full range.
On most platforms this is a matter of setting the "YUV range correction
disable" bit, and on VLV/CHV we'll just have to program the color
correction logic to pass the data through unmodified.
v2: Rebase
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Daniel Stone <daniel@fooishbar.org>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214192327.3250-9-ville.syrjala@linux.intel.com
Add support for the COLOR_ENCODING plane property which selects
the matrix coefficients used for the YCbCr->RGB conversion. Our
hardware can generally handle BT.601 and BT.709.
CHV pipe B sprites have a fully programmable matrix, so in theory
we could handle anything, but it doesn't seem all that useful to
expose anything beyond BT.601 and BT.709 at this time.
GLK can supposedly do BT.2020, but let's leave enabling that for
the future as well.
v2: Rename bit defines to match the spec more closely (Shashank)
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Daniel Stone <daniel@fooishbar.org>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214192327.3250-7-ville.syrjala@linux.intel.com
On GLK the plane CSC controls moved into the COLOR_CTL register.
Update the code to progam the YCbCr->RGB CSC mode correctly when
faced with an YCbCr framebuffer.
The spec is rather confusing as it calls the mode "YUV601 to RGB709".
I'm going to assume that just means it's going to use the YCbCr->RGB
matrix as specified in BT.601 and doesn't actually change the gamut.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Daniel Stone <daniel@fooishbar.org>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214192327.3250-6-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Turns out the VLV/CHV fixed function sprite CSC expects full range
data as input. We've been feeding it limited range data to it all
along. To expand the data out to full range we'll use the color
correction registers (brightness, contrast, and saturation).
On CHV pipe B we were actually doing the right thing already because we
progammed the custom CSC matrix to do expect limited range input. Now
that well pre-expand the data out with the color correction unit, we
need to change the CSC matrix to operate with full range input instead.
This should make the sprite output of the other pipes match the sprite
output of pipe B reasonably well. Looking at the resulting pipe CRCs,
there can be a slight difference in the output, but as I don't know
the formula used by the fixed function CSC of the other pipes, I don't
think it's worth the effort to try to match the output exactly. It
might not even be possible due to difference in internal precision etc.
One slight caveat here is that the color correction registers are single
bufferred, so we should really be updating them during vblank, but we
still don't have a mechanism for that, so just toss in another FIXME.
v2: Rebase
v3: s/bri/brightness/ s/con/contrast/ (Shashank)
v4: Clarify the constants and math (Shashank)
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Daniel Stone <daniel@fooishbar.org>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: "Tang, Jun" <jun.tang@intel.com>
Reported-by: "Tang, Jun" <jun.tang@intel.com>
Cc: stable@vger.kernel.org
Fixes: 7f1f3851fe ("drm/i915: sprite support for ValleyView v4")
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214192327.3250-5-ville.syrjala@linux.intel.com
Gen11 will add more VCS and VECS rings so prepare the
infrastructure to support that.
Bspec: 7021
v2: Rebase.
v3: Rebase.
v4: Rebase.
v5: Rebase.
v6:
- Update for POR changes. (Daniele Ceraolo Spurio)
- Add provisional guc engine ids - to be checked and confirmed.
v7:
- Rebased.
- Added the new ring masks.
- Added the new HW ids.
v8:
- Introduce I915_MAX_VCS/VECS to avoid magic numbers (Michal)
v9: increase MAX_ENGINE_INSTANCE to 3
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180228101153.7224-1-mika.kuoppala@linux.intel.com
To pull in the HDCP changes, especially wait_for changes to drm/i915
that Chris wants to build on top of.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
Since we no longer have a 1:1 correspondence between ports and AUX
channels, let's give AUX channels their own enum. Makes it easier
to tell the apples from the oranges, and we get rid of the
port E AUX power domain FIXME since we now derive the power domain
from the actual AUX CH.
v2: Rebase due to AUX F
v3: Split out the power domain fix (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v2
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-2-ville.syrjala@linux.intel.com
It turns out that HSW has a register that tells us how many EUs are
disabled per half-slice (roughly a similar notion to subslice). We
didn't read those registers so far as most userspace drivers didn't
need those values prior to Gen8, but an internal library would like to
have access to this.
Since we already have the getparam interface, there is no harm in
exposing this.
v2: Rename bits value (Joonas)
v3: s/GEM_BUG_ON/MISSING_CASE/ (Joonas)
v4: s/GEM_BUG_ON/MISSING_CASE/ again... (Lionel)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221204902.23084-1-lionel.g.landwerlin@intel.com
Register Address for CNL_PORT_DW5_LN0_D is 0x162E54, but current code is
defining it as 0x162ED4. Similarly for CNL_PORT_DW7_LN0_D register address
is defined 0x162EDC instead of 0x162E5C, fix it.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Fixes: 04416108cc ("drm/i915/cnl: Add registers related to voltage swing sequences.")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180215095643.3844-2-mahesh1.kumar@intel.com
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlqDR7wACgkQlvcN/ahK
BwrxxAgAm3HrrSvtfFPooUsVuodl7KxUF9Mc/MzCNkakP3+Gs0PBE6pp+PhpcBT4
7WwkONTvVKgtnhoIzl8k0Xp8TrDZDWFzpDUluug2knr4nHHkksXtimnz9sfyzGHw
s5XofrV8KQe710grKvUry1VtBrlGRGchd+Xjg1bl+BONnwTmJ8c53npa+d6X0nnt
c+qlP7U9ZawIb59eSL98CuaYsH8oQcMya/jUlb96ky+mx4ugHv9J3ePYIZTqqNDq
/YY1xVhlDQx8iKx7yUp8mreHp5tBL/o3hNNmLMnPDx8jwZfKt7R9MZHH+RRhgl71
TZJmZMUmUyUntVV9NVim8GVHMyDcYQ==
=3uTU
-----END PGP SIGNATURE-----
Merge tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Add HDCP support to i915 drm driver.
* tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (26 commits)
drm/i915: fix misalignment in HDCP register def
drm/i915: Reauthenticate HDCP on failure
drm/i915: Detect panel's hdcp capability
drm/i915: Optimize HDCP key load
drm/i915: Retry HDCP bksv read
drm/i915: Connector info in HDCP debug msgs
drm/i915: Stop encryption for repeater with no sink
drm/i915: Handle failure from 2nd stage HDCP auth
drm/i915: Downgrade hdcp logs from INFO to DEBUG_KMS
drm/i915: Restore HDCP DRM_INFO when with no downstream
drm/i915: Check for downstream topology errors
drm/i915: Start repeater auth on READY/CP_IRQ
drm/i915: II stage HDCP auth for repeater only
drm/i915: Extending HDCP for HSW, BDW and BXT+
drm/i915/dp: Fix compilation of intel_dp_hdcp_check_link
drm/i915: Only disable HDCP when it's active
drm/i915: Don't allow HDCP on PORT E/F
drm/i915: Implement HDCP for DisplayPort
drm/i915: Implement HDCP for HDMI
drm/i915: Add function to output Aksv over GMBUS
...
ICL has 2 slices of DBuf, enable both the slices during display init.
Ideally we should only enable the second slice when needed in order to
save power, but while we're not there yet, adopt the simpler solution
to keep us bug-free.
v2 (from Paulo):
- Add the TODO comment.
- Reorganize where things are defined.
- Fix indentation.
- Remove unnecessary POSTING_READ() calls.
- Improve the commit message.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-5-paulo.r.zanoni@intel.com
This code is similar enough to the CNL code that I considered just
adding ICL support to the CNL function, but I think it's still
different enough, and having a function specific to ICL allows us to
more easily adapt code in case the spec changes more later.
We're still missing the power wells and the mbus code, so leave those
pieces with a FIXME comment while they're not here yet.
v2: Don't use _PICK, don't WARN_ON(1), don't forget the chicken bits.
v3: Use _MMIO_PORT() (Ville).
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v2)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-4-paulo.r.zanoni@intel.com
This commit adds the basic CDCLK functions, but it's still missing
pieces of the display initialization sequence.
v2:
- Implement the voltage levels.
- Rebase.
v3:
- Adjust to the new "bypass" clock (Imre).
- Call intel_dump_cdclk_state() too.
- Rename a variable to avoid confusion.
- Simplify the DVFS part.
v4:
- Remove wrong bit definition (James).
- Also drive-by fix the coding style for the register definition we
touched.
v5:
- Comment style (checkpatch).
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206193346.18272-1-paulo.r.zanoni@intel.com
On ICL we have two sets of registers: one for port A and another for
port B. The set of port A registers is the same as the CNL registers.
Since the procmon table on ICL is the same we want to reuse the CNL
function. To do that we add a port argument and make CNL always call
the function passing port A. This way, we'll be able to easily reuse
the function on ICL when we add icl_display_core_init().
v2: Don't use _PICK() when you can use a ternary operator.
v3: Don't use a ternary operation when you can use _MMIO_PORT (Ville).
Add an extra comment about why we're passing PORT_A (James).
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-2-paulo.r.zanoni@intel.com
This patch clears a single bit. The bit is 0 by default but expected
not to be set. Explicitly clearing the bit in this patch is intended
to indicate some thinking has occurred, and that we want this bit
cleared and we are not just excepting the default value.
We also stop setting GFX_RUN_LIST_ENABLE, which is correct since that
bit is gone.
v2 (from Paulo): fix indentation.
v3: Changed GEN check to >= 11. Corrected author name.
v4 (from Paulo): improve commit message (Daniele).
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-9-paulo.r.zanoni@intel.com
ICL+ adds changes the PLANE_CTL_FORMAT field from [27:24] to [27:23],
however, all existing PLANE_CTL_FORMAT_* definitions still map to the
correct values. Add an ICL_PLANE_CTL_FORMAT_MASK definition, and use
that for masking for the conversion to fourcc.
v2: No changes
v3: Change new definition name, drop comment (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-8-paulo.r.zanoni@intel.com
This patch introduce MBus control registers and their bit-fields
MBUS_ABOX_CTL
MBUS_BBOX_CTL
MBUS_DBOX_CTL
MBUS_UBOX_CTL
Changes Since V1:
- Use function like macros (Paulo)
- fix copy-paste error (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-6-paulo.r.zanoni@intel.com
Now let's finish the Port-F support by adding the
proper port F detection, irq and power well support.
v2: Rebase
v3: Use BIT_ULL
v4: Cover missed case on ddi init.
v5: Update commit message.
v6: Rebase on top of display headers rework.
v7: Squash power-well handling related to DDI F to this
patch to avoid warns as pointed out by DK.
v8: Introduce DDI_F_LANES to PG2. (DK)
v9: Squash in the PORT_F case for enabling DP MST encoder. (DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-9-rodrigo.vivi@intel.com
Since when it got introduced with commit '555e38d27317
("drm/i915/cnl: DDI - PLL mapping")' the support for Port F
was wrong, because Port F bits are far from bits used
for A to E.
Since Port F is not used so far we don't need to propagate
Fixes back there.
v2: Reuse _SHIFT definition to avoid complicated duplication (DK).
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-5-rodrigo.vivi@intel.com
This was wrong since its introduction on commit '04416108ccea
("drm/i915/cnl: Add registers related to voltage swing sequences.")'
But since no Port F was needed so far we don't need to
propagate fixes back there.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-4-rodrigo.vivi@intel.com
On some Cannonlake SKUs we have a dedicated Aux for port F,
that is only the full split between port A and port E.
There is still no Aux E for Port E, as in previous platforms,
because port_E still means shared lanes with port A.
v2: Rebase.
v3: Add couple missed PORT_F cases on intel_dp.
v4: Rebase and fix commit message.
v5: Squash Imre's "drm/i915: Add missing AUX_F power well string"
v6: Rebase on top of display headers rework.
v7: s/IS_CANNONLAKE/IS_CNL_WITH_PORT_F (DK)
v8: Fix Aux bits for Port F (DK)
v9: Fix VBT definition of Port F (DK).
v10: Squash power well addition to this patch to avoid
warns as pointed by DK.
v11: Clean up squashed commit message. (David)
v12: Remove unnecessary handling for older platforms (DK)
Adding AUX_F to PG2 following other existent ones. (DK)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-2-rodrigo.vivi@intel.com
Apparently SKL/KBL/CFL need some manual help to get the
programmed HDMI vswing to stick. Implement the relevant
workaround (display w/a #1143).
Note that the relevant chicken bits live in a transcoder register
even though the bits affect a specific DDI port rather than a
specific transcoder. Hence we must pick the correct transcoder
register instance based on the port rather than based on the
cpu_transcoder.
Also note that for completeness I included support for DDI A/E
in the code even though we never have HDMI on those ports.
v2: CFL needs the w/a as well (Rodrigo and Art)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122174131.28046-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Current code always select _CNL_AUX_ANAOVRD1_B
register regardless the pw in use.
CNL_DISP_PW_AUX_B = 9
CNL_DISP_PW_AUX_C = 10
CNL_DISP_PW_AUX_D = 11
And for pick we want
B = 0
C = 1
D = 2
Fixes: ddd39e4b3f ("drm/i915/cnl: apply Display WA #1178 to fix type C dongles")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123215245.24026-1-rodrigo.vivi@intel.com
MMIO addresses and register definition for the new interrupt
registers in Gen11.
v2: Removed spelt out VCS and VECS bit definitions. (Daniel Vetter)
v3: Adjust VCS and VECS. (Daniele Ceraolo Spurio)
v4: Bikeshedding (Paulo).
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109232336.11029-5-paulo.r.zanoni@intel.com
In ICP, there are three TC ports and 3 DDI ports.
v2:
- Correct Pin mapping.
v3:
- Update pin mapping into per platform implementation
rather than previous approach of port wise mapping.
v4:
- Update GMBUS_NUM_PINS (Paulo)
v5:
- rebase.
v6:
- Update function name, GMBUS_PIN_NUM (Paulo)
v7 (from Paulo):
- Make it apply.
v8 (from Paulo):
- Maintain consistent if ladder ordering.
Suggested by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-8-paulo.r.zanoni@intel.com
Add register definitions for setting the rawclock.
Set the numerator,denominator and divider values.
v2: Simplify the commit message. Simplify the math.
Add register bits for numerator. (Paulo)
v3 (from Paulo): coding style bikesheds.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-5-paulo.r.zanoni@intel.com
Display WA #1178 is meant to fix Aux channel voltage swing too low with
some type C dongles. Although it is for type C, HW engineers reported
that it can be applied to all external ports even if they are not going
to type C.
For CNL we apply the workaround every time Aux B, C and D are powering
up since they will lose the configuration when powered down.
v2: Use common tag for WA
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128220553.22435-1-lucas.demarchi@intel.com
This register does not contain it. Instead, we have to look into FAULT_TLB_DATA0 & 1
(where, by the way, we can also get the address space).
v2: Right formatting
v3:
- Use 12 (as per the register format) instead of PAGE_SIZE (Chris)
- s/BITS_44_TO_47/HIGHBITS (Chris)
- Right formatting, this time for real
Fixes: b03ec3d67a ("drm/i915: There is only one fault register from GEN8 onwards")
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1513982329-32191-1-git-send-email-oscar.mateo@intel.com
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch adds HDCP support for HDMI connectors by implementing
the intel_hdcp_shim.
Nothing too special, just a bunch of DDC reads/writes.
Changes in v2:
- Rebased on drm-intel-next
Changes in v3:
- Initialize new worker
Changes in v4:
- Remove SKL_ prefix from most register names (Daniel)
- Wrap sanity checks in WARN_ON (Daniel)
- Consolidate the enable/disable functions into one toggle fn
- Use intel_hdcp_init (Daniel)
Changes in v5:
- checkpatch whitespace nits
Changes in v6:
- None
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-9-seanpaul@chromium.org
Once the Aksv is available in the PCH, we need to get it on the wire to
the receiver via DDC. The hardware doesn't allow us to read the value
directly, so we need to tell GMBUS to source the Aksv internally and
send it to the right offset on the receiver.
The way we do this is to initiate an indexed write where the index is
the Aksv register offset. We write dummy values to GMBUS3 as if we were
sending the key, and the hardware slips in the "real" values when it
goes out.
Changes in v2:
- None
Changes in v3:
- Uses new index write feature (Ville)
Changes in v4:
- None
Changes in v5:
- checkpatch whitespace fix
Changes in v6:
- None
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-8-seanpaul@chromium.org
This patch adds the framework required to add HDCP support to intel
connectors. It implements Aksv loading from fuse, and parts 1/2/3
of the HDCP authentication scheme.
Note that without shim implementations, this does not actually implement
HDCP. That will come in subsequent patches.
Changes in v2:
- Don't open code wait_fors (Chris)
- drm_hdcp.c under MIT license (Daniel)
- Move intel_hdcp_disable() call above ddi_disable (Ram)
- Fix // comments (I wore a cone of shame for 12 hours to atone) (Daniel)
- Justify intel_hdcp_shim with comments (Daniel)
- Fixed async locking issues by adding hdcp_mutex (Daniel)
- Don't alter connector_state in enable/disable (Daniel)
Changes in v3:
- Added hdcp_mutex/hdcp_value to make async reasonable
- Added hdcp_prop_work to separate link checking & property setting
- Added new helper for atomic_check state tracking (Daniel)
- Moved enable/disable into atomic_commit with matching helpers
- Moved intel_hdcp_check_link out of all locks when called from dp
- Bumped up ksv_fifo timeout (noticed failure on one of my dongles)
Changes in v4:
- Remove SKL_ prefix from most register names (Daniel)
- Move enable/disable back to modeset path (Daniel)
- s/get_random_long/get_random_u32/ (Daniel)
- Remove mode_config.mutex lock in prop_work (Daniel)
- Add intel_hdcp_init to handle init of conn components (Daniel)
- Actually check return value of attach_property
- Check Bksv is valid before trying to authenticate (Ram)
Changes in v5:
- checkpatch whitespace changes
- s/DRM_MODE_CONTENT_PROTECTION_OFF/DRM_MODE_CONTENT_PROTECTION_UNDESIRED/
- Fix ksv list wait timeout (actually wait 5s)
- Increase the R0 timeout to 300ms (Ram)
Changes in v6:
- SPDX license
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ramalingam C <ramalingm.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180108195545.218615-6-seanpaul@chromium.org
Geminilake requires the 3D driver to select whether barriers are
intended for compute shaders, or tessellation control shaders, by
whacking a "Barrier Mode" bit in SLICE_COMMON_ECO_CHICKEN1 when
switching pipelines. Failure to do this properly can result in GPU
hangs.
Unfortunately, this means it needs to switch mid-batch, so only
userspace can properly set it. To facilitate this, the kernel needs
to whitelist the register.
The workarounds page currently tags this as applying to Broxton only,
but that doesn't make sense. The documentation for the register it
references says the bit userspace is supposed to toggle only exists on
Geminilake. Empirically, the Mesa patch to toggle this bit appears to
fix intermittent GPU hangs in tessellation control shader barrier tests
on Geminilake; we haven't seen those hangs on Broxton.
v2: Mention WA #0862 in the comment (it doesn't have a name).
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180105085905.9298-1-kenneth@whitecape.org
Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
enabling or in previous enabling."
This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.
We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.
This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com
Gen9+ need to disable GMBUS clock gating when doing multi part
transfers. Otherwise clock gating will kick in when GMBUS is in
the WAIT state and presumably that will corrupt the transfer.
This is documented as Display WA #0868.
Apparently older hardware doesn't allow clock gating in the WAIT
state and thus are unaffected by this problem.
v2: Limit the PCH w/a to gen9 and gen10 only (DK)
Actually change it to check the PCH type instead since
it's the PCH that actually contains the GMBUS hardware
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20171221202432.17373-1-ville.syrjala@linux.intel.com
There seems to be another clock gating issue which the workaround is
described as:
"WA: Set 0xE4F0[1] = 1 to disable Early EOT of thread."
Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171216001117.14232-2-rafael.antognolli@intel.com
From: Chris Wilson <chris@chris-wilson.co.uk>
From: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
From: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
The first goal is to be able to measure GPU (and invidual ring) busyness
without having to poll registers from userspace. (Which not only incurs
holding the forcewake lock indefinitely, perturbing the system, but also
runs the risk of hanging the machine.) As an alternative we can use the
perf event counter interface to sample the ring registers periodically
and send those results to userspace.
Functionality we are exporting to userspace is via the existing perf PMU
API and can be exercised via the existing tools. For example:
perf stat -a -e i915/rcs0-busy/ -I 1000
Will print the render engine busynnes once per second. All the performance
counters can be enumerated (perf list) and have their unit of measure
correctly reported in sysfs.
v1-v2 (Chris Wilson):
v2: Use a common timer for the ring sampling.
v3: (Tvrtko Ursulin)
* Decouple uAPI from i915 engine ids.
* Complete uAPI defines.
* Refactor some code to helpers for clarity.
* Skip sampling disabled engines.
* Expose counters in sysfs.
* Pass in fake regs to avoid null ptr deref in perf core.
* Convert to class/instance uAPI.
* Use shared driver code for rc6 residency, power and frequency.
v4: (Dmitry Rogozhkin)
* Register PMU with .task_ctx_nr=perf_invalid_context
* Expose cpumask for the PMU with the single CPU in the mask
* Properly support pmu->stop(): it should call pmu->read()
* Properly support pmu->del(): it should call stop(event, PERF_EF_UPDATE)
* Introduce refcounting of event subscriptions.
* Make pmu.busy_stats a refcounter to avoid busy stats going away
with some deleted event.
* Expose cpumask for i915 PMU to avoid multiple events creation of
the same type followed by counter aggregation by perf-stat.
* Track CPUs getting online/offline to migrate perf context. If (likely)
cpumask will initially set CPU0, CONFIG_BOOTPARAM_HOTPLUG_CPU0 will be
needed to see effect of CPU status tracking.
* End result is that only global events are supported and perf stat
works correctly.
* Deny perf driver level sampling - it is prohibited for uncore PMU.
v5: (Tvrtko Ursulin)
* Don't hardcode number of engine samplers.
* Rewrite event ref-counting for correctness and simplicity.
* Store initial counter value when starting already enabled events
to correctly report values to all listeners.
* Fix RC6 residency readout.
* Comments, GPL header.
v6:
* Add missing entry to v4 changelog.
* Fix accounting in CPU hotplug case by copying the approach from
arch/x86/events/intel/cstate.c. (Dmitry Rogozhkin)
v7:
* Log failure message only on failure.
* Remove CPU hotplug notification state on unregister.
v8:
* Fix error unwind on failed registration.
* Checkpatch cleanup.
v9:
* Drop the energy metric, it is available via intel_rapl_perf.
(Ville Syrjälä)
* Use HAS_RC6(p). (Chris Wilson)
* Handle unsupported non-engine events. (Dmitry Rogozhkin)
* Rebase for intel_rc6_residency_ns needing caller managed
runtime pm.
* Drop HAS_RC6 checks from the read callback since creating those
events will be rejected at init time already.
* Add counter units to sysfs so perf stat output is nicer.
* Cleanup the attribute tables for brevity and readability.
v10:
* Fixed queued accounting.
v11:
* Move intel_engine_lookup_user to intel_engine_cs.c
* Commit update. (Joonas Lahtinen)
v12:
* More accurate sampling. (Chris Wilson)
* Store and report frequency in MHz for better usability from
perf stat.
* Removed metrics: queued, interrupts, rc6 counters.
* Sample engine busyness based on seqno difference only
for less MMIO (and forcewake) on all platforms. (Chris Wilson)
v13:
* Comment spelling, use mul_u32_u32 to work around potential GCC
issue and somne code alignment changes. (Chris Wilson)
v14:
* Rebase.
v15:
* Rebase for RPS refactoring.
v16:
* Use the dynamic slot in the CPU hotplug state machine so that we are
free to setup our state as multi-instance. Previously we were re-using
the CPUHP_AP_PERF_X86_UNCORE_ONLINE slot which is neither used as
multi-instance, nor owned by our driver to start with.
* Register the CPU hotplug handlers after the PMU, otherwise the callback
will get called before the PMU is initialized which can end up in
perf_pmu_migrate_context with an un-initialized base.
* Added workaround for a probable bug in cpuhp core.
v17:
* Remove workaround for the cpuhp bug.
v18:
* Rebase for drm_i915_gem_engine_class getting upstream before us.
v19:
* Rebase. (trivial)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121181852.16128-2-tvrtko.ursulin@linux.intel.com
This reverts commit 8f067837c4.
HSD says "WA withdrawn. It was causing corruption with some images.
WA is not strictly necessary since this bug just causes loss of FBC
compression with some sizes and images, but doesn't break anything."
Fixes: 8f067837c4 ("drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117010825.23118-1-radhakrishna.sripada@intel.com
Apparently there are some machines that put semi-sensible looking values
into the stolen "reserved" base and size, except those values are actually
outside the stolen memory. There is a bit in the register which
supposedly could tell us whether the reserved area is even enabled or
not. Let's check for that before we go trusting the base and size.
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171102151737.23336-1-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Display is not sending a PMRsp when a PMReq is received
at the same time that all planes are turned off.
State machine in the dcprunit is stuck in the WAIT4DONE
state which means that there is no fill_done.
WA: disable arbiter clock gating, set bit [27] of 0x46530
v2: As Ville pointed out, based on the description the issue
can happen when disabling the planes, similar to
WaRsPkgCStateDisplayPMReq:hsw
Also description of the issue was updated on commit
message to make it more clear that we need this
earlier.
v3: Restore comment about possibility to system hang
to where we are sure about it, without speculation. (Ville).
v4: Remove doubled sob. Actually do v3 changes :/
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171111000319.5040-1-rodrigo.vivi@intel.com
Since GLK, some plane configuration settings have moved to the
PLANE_COLOR_CTL register. Refactor handling of the register to work like
PLANE_CTL. This also allows us to fix the set/read of the plane Alpha
Mode for GLK+.
v2: Adjust ordering of platform checks to be newest->oldest, drop
redundant comment about alpha blending. (Ville)
v3: Move Alpha Mode bits out of skl_plane_ctl_format into
skl_plane_ctl_alpha, and drop glk_plane_ctl_format, drop initialization
of state->color_ctl on platforms that don't use it, and drop color_ctl
local var. (Ville)
v4: Consolidate skl_plane_ctl_format switch statement on formats that
return the same settings. (Ville)
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113181128.2926-1-james.ausmus@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Until Haswell/Baytrail, the hardware used to have a per engine fault
register (e.g. 0x4094 - render fault register, 0x4194 - media fault
register and so on). But since Broadwell, all these registers were
combined into a singe one and the engine id stored in bits 14:12.
Not only we should not been reading (and writing to) registers that do
not exist, in platforms with VCS2 (SKL), the address that would belong
this engine (0x4494, VCS2_HW = 4) is already assigned to other register.
v2: use less controversial function names (Chris).
v3: make non-exported functions static, remove now obsolete check for
engine presence before posting_read (Chris).
References: IHD-OS-BDW-Vol 2c-11.15, page 75.
References: IHD-OS-SKL-Vol 2c-05.16, page 350.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113173628.11689-1-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We use to have this fixed per generation, but starting with CNL userspace
cannot tell just off the PCI ID. Let's make this information available. This
is particularly useful for performance monitoring where much of the
normalization work is done using those timestamps (this include pipeline
statistics in both GL & Vulkan as well as OA reports).
v2: Use variables for 24MHz/19.2MHz values (Ewelina)
Renamed function & coding style (Sagar)
v3: Fix frequency read on Broadwell (Sagar)
Fix missing divide by 4 on <= gen4 (Sagar)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Tested-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171110190845.32574-7-lionel.g.landwerlin@intel.com
This name was added with the whitelisting of registers for building up OA
configs. It is contained in a range gen8 whitelist :
addr >= RPM_CONFIG0.reg && addr <= NOA_CONFIG(8).reg
Hence why the name isn't used anywhere.
v2: Fix register name again RPC->RCP (Matthew)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171110190845.32574-5-lionel.g.landwerlin@intel.com
GEN8_CONFIG0 (0xD00) is a protected by a lock (bit 31) which is set by
the BIOS, so there is no way we can enable the three chicken bits
mandated by the WA (the BIOS should be doing it instead).
v2: Rebased
v3: Standalone patch
References: b033bb6d5d ("drm/i915/gen9: Enable must set chicken bits in config0 reg")
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510185589-9100-2-git-send-email-oscar.mateo@intel.com
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The workaround for this is described as:
"if RenderSurfaceState.Num_Multisamples > 1, disable RCC clock gating if
RenderSurfaceState.Num_Multisamples == 1, set 0x7010[14] = 1"
Further documentation in the internal bug referenced by the bspec
suggest that any of the above suggestions should suffice to fix the
issue. We are going with disabling RCC clock gating.
Unfortunately, what we are doing doesn't match the name of the
workaround, but at least it matches its description.
This change improves CNL stability by avoiding some of the hangs seen in
the platform.
v2: Only disable RCC clock gating.
Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171103183027.5051-1-rafael.antognolli@intel.com
There is a possibility on gen9 hardware to miss the forcewake ack
message. The recommended workaround is to use another free
bit and toggle it until original bit is successfully acknowledged.
Some future gen9 revs might or might not fix the underlying issue but
using fallback forcewake bit dance can be considered as harmless:
without the ack timeout we never reach the fallback bit forcewake.
Thus as of now we adopt a blanket approach for all gen9 and leave
the bypassing the fallback bit approach for future patches if
corresponding hw revisions do appear.
Commit 83e3337204 ("drm/i915: Increase maximum polling time to 50ms
for forcewake request/clear ack") did increase the forcewake timeout.
If the issue was a delayed ack, future work could include finding
a suitable timeout value both for primary ack and reserve toggle
to reduce the worst case latency.
v2: use bit 15, naming, comment (Chris), only wait fallback ack
v3: fix return on fallback, backoff after fallback write (Chris)
v4: udelay on first pass, grammar (Chris)
v4: s/reserve/fallback
References: HSDES #1604254524
References: https://bugs.freedesktop.org/show_bug.cgi?id=102051
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171102094836.2506-1-mika.kuoppala@linux.intel.com
CNL adds an extra register for slice/subslice information.
Although no SKU is planed with an extra slice let's already
handle this extra piece of information so we don't have the
risk in future of getting a part that might have chosen this
part of the die instead of other slices or anything like that.
Also if subslice is disabled the information of eu ack for that
is garbage, so let's skip checks for eu if subslice is disabled
as we skip the subslice if slice is disabled.
The rest is pretty much like gen9.
v2: Remove IS_CANNONLAKE from gen9 status function.
v3: Consider s_max = 6 and ss_max=4 to run over all possible
slices and subslices possible by spec. Although no real
hardware will have that many slices/subslices.
To match with sseu info init.
v4: Fix offset calculation for slices 4 and 5.
Removed Oscar's rv-b since this change also needs review.
v5: Let's consider only valid bits for SLICE*_PGCTL_ACK.
This looks like wrong in Spec, but seems to be enough
for now. Whenever Spec gets updated and fixed we come
back and properly update the masks. Also add a FIXME,
so we can revisit this later when we find some strange
info on debugfs or when we noitce spec got updated.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171026001546.28203-1-rodrigo.vivi@intel.com
On CNL, individual wake rate limit was added to each engine.
GT can only go to RC6 if both Render and Media engines are
individually qualified. So we need to set their individual
wake rate limit.
+-----------------+---------------+--------------+--------------+
| | GT RC6 | Render C6 | Media C6 |
+-----------------+---------------+--------------+--------------+
| Wake rate limit | 0xA09C[31:16] | 0xA09C[15:0] | 0xA0A0[15:0] |
+-----------------+---------------+--------------+--------------+
v2: - Tune Render and Media wake rate values according to some extra
info I got from HW engineers. Value can be tuned, but for now
these are the recommended values.
- Fix typos pointed by James.
Cc: Nathan Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023224612.27208-1-rodrigo.vivi@intel.com
Otherwise we are blasting other bits in GEN8_L3SQCREG1 that might be important
(although we probably aren't at the moment because 0 seems to be the default
for all the other bits).
v2: Extra parentheses (Michel)
Fixes: 050fc46 ("drm/i915:bxt: implement WaProgramL3SqcReg1DefaultForPerf")
Fixes: 450174f ("drm/i915/chv: Tune L3 SQC credits based on actual latencies")
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508271945-14961-1-git-send-email-oscar.mateo@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rename DP_AUX_CH_CTL_TIME_OUT_1600us to DP_AUX_CH_CTL_TIME_OUT_MAX, as
the meaning of the (3 << 26) value varies per platform, but it's always the
maximum timeout for that platform. Pre-CNL it means 1600us, and for CNL
it means 3200us.
v2:
-Split in to two patches (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012213037.4245-1-james.ausmus@intel.com
Before we can enable 64K pages through the IPS bit, we must first enable
it through MMIO, otherwise the page-walker will simply ignore it.
v2: add comment mentioning that 64K is BDW+
v3: move to more suitable home
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171006145041.21673-11-matthew.auld@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171006221833.32439-10-chris@chris-wilson.co.uk
Supporting fine-granularity preemption levels may require changes in
userspace batch buffer programming. Therefore, we need to fallback to
safe default values, rather that use hardware defaults. Userspace is
still able to enable fine-granularity, since we're whitelisting the
register controlling it in WaEnablePreemptionGranularityControlByUMD.
v2: Extend w/a to cover Cannonlake
v3: Fix commentary to include both fake w/a names.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003203453.15692-2-chris@chris-wilson.co.uk
On GLK and CNL enabling a pipe with its pipe scaler enabled will result
in a FIFO underrun. This happens only once after driver loading or
system/runtime resume, more specifically after power well 1 gets
enabled; subsequent modesets seem to be free of underruns. The BSpec
workaround for this is to disable the pipe scaler clock gating for the
duration of modeset. Based on my tests disabling clock gating must be
done before enabling pipe scaling and we can re-enable it after the pipe
is enabled and one vblank has passed.
For consistency I also checked if plane scaling would cause the same
problem, but that doesn't seem to trigger this problem.
The patch is based on an earlier version from Ander.
v2 (Rodrigo):
- Set also CLKGATE_DIS_PSL bits 8 and 9.
- Add also the BSpec workaround ID.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100302
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171002075557.32615-1-imre.deak@intel.com
Cannonlake Slice and Subslice information has changed.
This patch initially provided by Ben adds the proper sseu
initialization.
v2: This v2 done by Rodrigo includes:
- Fix on Total slices count by avoiding [1][2] and [2][2].
- Inclusion of EU Per Subslice.
- Commit message.
v3: This v3 done by Rodrigo includes:
- Handle all possible bits and extra fuse register.
- Use INTEL_GEN macro.
- Fully assume uniform distribution so remove union
with eu_per_subslice and add proper the comment.
v4: This v4 done by Rodrigo includes:
- Consider all bits available: 6 bits for slices [27:22]
and 4 for subslices [21:18].
v5: This v5 done by Rodrigo includes:
- sseu->subslice_mask = (1 << 4) - 1 - missed on previous
versions and noticed by Oscar.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170920183525.20530-1-rodrigo.vivi@intel.com
For certain platforms on certain encoders, timings are driven
from port instead of pipe. Thus, we can't rely on pipe scanline
registers to get the timing information. Some cases scanline
register read will not be functional.
This is causing vblank evasion logic to fail since it relies on
scanline, causing atomic update failure warnings.
This patch uses pipe framestamp and current timestamp registers
to calculate scanline. This is an indirect way to get the scanline.
It helps resolve atomic update failure for gen9 dsi platforms.
v2: Addressed Ville and Daniel's review comments. Updated the
register MACROs, handled race condition for register reads,
extracted timings from the hwmode. Removed the dependency on
crtc->config to get the encoder type.
v3: Made get scanline function generic
v4: Addressed Ville's review comments. Added a flag to decide timestamp
based scanline reporting. Changed 64bit variables to u32
v5: Adressed Ville's review comments. Put the scanline compute function
at the place of caller. Removed hwmode flags from uapi and used a local
i915 data structure instead.
v6: Used vblank hwmode to get the timings.
v7: Fixed sparse warnings, indentation and minor review comments.
v8: Limited this only for Gen9 DSI.
Credits-to: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1506347761-4201-1-git-send-email-vidya.srinivas@intel.com
"CNL PCH chance of hang when software accesses south display
registers after hotplug is enabled.
Workaround: Program 0xC2000 bits 11:8 = 0xF before enabling
south display hotplug detection."
"Workaround only needs to be applied to pre-production steppings
used in graphics capable SKUs, but it is easier to apply to
everything, and does not hurt."
v2: Moving from clock gating to right before enabling
SHOTPLUG_CTL as it should be.
v3: Align with SOUTH_CHICKEN1 (DK) and consequently use proper
spaces on bits definition since other bits around already use
new style. And now that checkpatch is not noise anymore I also
fixed the reg read mask to avoid going over 80 chars.
Suggested-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919215703.25947-1-rodrigo.vivi@intel.com
No functional changes. Only change the macro from
"DPLL_CFGCR0_DC0_FRAC_SHIFT to DPLL_CFGCR0_DCO_FRACTION_SHIFT
to be consistent with DPLL_CFGCR0_DCO_FRACTION_MASK
and DPLL_CFGCR0_DCO_FRACTION
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505413899-30876-1-git-send-email-manasi.d.navare@intel.com
Use the LLC/eLLC hotspot avoidance mode for CCS on LLC machines. This is
reported to give better performance.
Testing has indicated that we don't need to enforce any massive 2 or 4
MiB alignment for all compressed resources even though there are still
plenty of stale comments in the spec suggesting that we do.
We do need to make sure every hardware unit that deals with the
compressed data uses the same hash mode.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170824191100.10949-4-ville.syrjala@linux.intel.com
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Macro params shall be wrapped into () to avoid unexpected results.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908161130.22424-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch adds IPC support. This patch also enables IPC in all supported
platforms based on has_ipc flag.
IPC (Isochronous Priority Control) is the hardware feature, which
dynamically controls the memory read priority of Display.
When IPC is enabled, plane read requests are sent at high priority until
filling above the transition watermark, then the requests are sent at
lower priority until dropping below the level 0 watermark.
The lower priority requests allow other memory clients to have better
memory access. When IPC is disabled, all plane read requests are sent at
high priority.
Changes since V1:
- Remove commandline parameter to disable ipc
- Address Paulo's comments
Changes since V2:
- Address review comments
- Set ipc_enabled flag
Changes since V3:
- move ipc_enabled flag assignment inside intel_ipc_enable function
Changes since V4:
- Re-enable IPC after suspend/resume
Changes since V5:
- Enable IPC for all gen >=9 except SKL
Changes since V6:
- fix commit msg
- after resume program IPC based on SW state.
Changes since V7:
- Modify IPC support check based on HAS_IPC macro (suggested by Chris)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-8-mahesh1.kumar@intel.com
Wa for B-stepping only.
A for a hang issue that requires throttling EU performace
to 12.5% to avoid back pressure to thread dispatch
v2: Rebased. No change from v1.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170906220325.24524-1-rodrigo.vivi@intel.com
Skip compressing 1 segment at the end of the frame,
avoid a pixel count mismatch nuke event when last active
pixel and dummy pixel has same color for Odd Plane
Width / Height.
For both platforms Gemini Lake and Cannon Lake.
v2: Use function-like macro and also use mask to clean
to make sure bit 11 is 0. (Suggested by Paulo).
v3: Add Display WA notation and also apply for GLK.
Both Forgotten on v2.
Using "GLK_" prefix since GLK came before CNL.
v4: Forgot to "|=" when moving directly macro to masked
val. (Noticed by Paulo.)
v5: Rebased on top of 0a46ddd57c ("drm/i915/cnp: Wa 1181:
Fix Backlight issue")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905193013.31710-1-rodrigo.vivi@intel.com
This workaround fixes a CNL PCH bug when changing
backlight from a lower frequency to a higher frequency.
During random reboot cycles, display backlight seems to
be off/ dim for 2-3 mins.
The only functional change on this patch is to
set bit 13 of 0xC2020 for CNL PCH.
The rest of patch is organizing identation around
those bits definitions and re-organizing CFL workarounds.
v2: Only add the bit that matters without touching others
around (Jani).
Rebase on top of clock gating functions rename.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170831045223.3960-1-rodrigo.vivi@intel.com
On CNL B0 stepping GAM is not able to detect some deadlock
condition and then rise the rise the gam_coh_flush.
WA database and spec both mentions to set 4AB8[24]=1 as
workaround. Although register offset 0x4AB8 is not
documented for any platform.
References: HSD#1945815, BSID#1112
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829230751.21047-1-rodrigo.vivi@intel.com
WA to enable HW L1 Banking fix that allows aniso to operate
at full sample rate.
References: HSD#1937670
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Anuj Phogat <anuj.phogat@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829230723.20898-1-rodrigo.vivi@intel.com
When FBC is enabled for linear, legacy Y-tiled and Yf-tiled
surfaces on gen9, the cfb stride must be programmed by SW as
cfb_stride = ceiling[(at least plane width in pixels)/
(32 * compression limit factor)] * 8
v2: Minor fix for a build error
v3: Fixed subject, register name and platform check (Ville)
v4: Added WA details in comment (Paulo)
v5:
- Read modified reg write to preserve other bit values (Paulo)
- Store modified stride value in reg_params (Paulo)
- Keep GLK out of the WA (Paulo)
v6:
- added additional field in reg_params for gen9_wa_cfb_stride (Paulo)
- Used appropriate bit mask while writing the register (Paulo)
v7 (from Paulo):
- Fix coding style and spacing issues.
- Mask the old values before writing.
- Bikeshed comments and unnecessary checks.
Signed-off-by: Praveen Paneri <praveen.paneri@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502389833-32621-1-git-send-email-praveen.paneri@intel.com
To avoid a potential hang condition with TLB invalidation
we need to enable masked bit 5 of MMIO 0xE5F0 at boot.
Same workaround was in place for previous platforms,
but the register offset has changed for CNL.
But also BSpec doesn't mention the bit 15 as set on gen9
platforms and mark bit as reserved on CNL.
v2: Improve commit message accepting Oscar's suggestion.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170823203504.10012-1-rodrigo.vivi@intel.com
CS sometimes hangs on 3D Push Constant dispatches with the new
deref enhancement logic in CNL.
v2: Improve the commit message (Rodrigo)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503518191-19116-1-git-send-email-oscar.mateo@intel.com
This bit enables hardware that will change the approximation used for distances
calculations for AA wide lines so that they are rendered more accurately.
The default value for this bit leaves the legacy behavior. There is no good
reason to not enable the new approximation except if comparing to previous GEN
rendered images.
v2: Rebase
v3: Fix author.
Rebased by Rodrigo who also added a comment as suggested by Oscar.
Since it is surrounded by Workarounds let's just add a comment to
make clear it is not an Wa.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815231651.975-4-rodrigo.vivi@intel.com
Let's inherit workarounds from previous platforms that
according to wa_database and BSpec are still valid for
Cannonlake.
v2: Add missed workarounds.
v3: Rebase
v4: Remove bad chunk that was added to rc6 disable. (Ander)
Also remove A0 W/a that are not needed anymore.
v5: Rebase on top of CFL.
v6: Remove empty gen9_init_perctx_bb and gen9_init_indirectctx_bb
since they don't carry any gen10 related W/a. (by Oscar).
Also Remove A0 exclusive workaround.
v7: Remove more A0 exclusive workarounds. As pointed out by Oscar
many workarounds were changed to be A0 only so let's remove
them.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815231651.975-1-rodrigo.vivi@intel.com
Different from previous platforms, on CNL+ there's separated
registers for separated indexes.
v2: Remove comments regarding uncertainty around the table.
v3: Remove extra line (by Ben)
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815232539.3562-1-rodrigo.vivi@intel.com
Future platforms increase the number of power wells which require
additional control registers. A convenient way to select the correct
register is to use the high bits of the power well ID as index. This
patch only prepares for this, while upcoming platform enabling patches
will add the actual new power well IDs and corresponding power well
control registers.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170814151530.24154-2-imre.deak@intel.com
This is not to try to force a new style; this is my interpretation of
what the most common existing style is.
With hopes I don't need to answer so many questions about style going
forward.
Start a new style section in the i915 document to bolt the register
style guide into.
v2: vertical alignment, incorporate to kernel-doc, and more
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9de4a5b1bea4e76461c70a1dd66751581de0124f.1502368010.git.jani.nikula@intel.com
SKL+ display engine can scan out certain kinds of compressed surfaces
produced by the render engine. This involved telling the display engine
the location of the color control surfae (CCS) which describes
which parts of the main surface are compressed and which are not. The
location of CCS is provided by userspace as just another plane with its
own offset.
Add the required stuff to validate the user provided AUX plane metadata
and convert the user provided linear offset into something the hardware
can consume.
Due to hardware limitations we require that the main surface and
the AUX surface (CCS) be part of the same bo. The hardware also
makes life hard by not allowing you to provide separate x/y offsets
for the main and AUX surfaces (excpet with NV12), so finding suitable
offsets for both requires a bit of work. Assuming we still want keep
playing tricks with the offsets. I've just gone with a dumb "search
backward for suitable offsets" approach, which is far from optimal,
but it works.
Also not all planes will be capable of scanning out compressed surfaces,
and eg. 90/270 degree rotation is not supported in combination with
decompression either.
This patch may contain work from at least the following people:
* Vandana Kannan <vandana.kannan@intel.com>
* Daniel Vetter <daniel@ffwll.ch>
* Ben Widawsky <ben@bwidawsk.net>
v2: Deal with display workarounds 0390, 0531, 1125 (Paulo)
v3: Pretend CCS tiles are regular 128 byte wide Y tiles (Jason)
Put the AUX register defines to the correct place
Fix up the slightly bogus rotation check
v4: Use I915_WRITE_FW() due to plane update locking changes
s/return -EINVAL/goto err/ in intel_framebuffer_init()
Eliminate a bunch hardcoded numbers in CCS code
v5: (By Ben)
conflict resolution +
- res_blocks += fixed_16_16_to_u32_round_up(y_tile_minimum);
+ res_blocks += fixed16_to_u32_round_up(y_tile_minimum);
v6: (daniels) Fix botched commit message.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Ville Syrjä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Stone <daniels@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170801165817.7063-1-ben@bwidawsk.net
Bit 29 of SRD_CTL needs to have its value preserved according to the
B-Spec, so right before we write out the register we go ahead and read
the register and preserve the value of that bit before we write out
the configured register value.
v2: Spaces => tabs, minor name change, and commit message wording (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502229094-13392-1-git-send-email-jim.bride@linux.intel.com
The motivation behind this new interface is expose at runtime the
creation of new OA configs which can be used as part of the i915 perf
open interface. This will enable the kernel to learn new configs which
may be experimental, or otherwise not part of the core set currently
available through the i915 perf interface.
v2: Drop DRM_ERROR for userspace errors (Matthew)
Add padding to userspace structure (Matthew)
s/guid/uuid/ (Matthew)
v3: Use u32 instead of int to iterate through registers (Matthew)
v4: Lock access to dynamic config list (Lionel)
v5: by Matthew:
Fix uninitialized error values
Fix incorrect unwiding when opening perf stream
Use kmalloc_array() to store register
Use uuid_is_valid() to valid config uuids
Declare ioctls as write only
Check padding members are set to 0
by Lionel:
Return ENOENT rather than EINVAL when trying to remove non
existing config
v6: by Chris:
Use ref counts for OA configs
Store UUID in drm_i915_perf_oa_config rather then using pointer
Shuffle fields of drm_i915_perf_oa_config to avoid padding
v7: by Chris
Rename uapi pointers fields to end with '_ptr'
v8: by Andrzej, Marek, Sebastian
Update register whitelisting
by Lionel
Add more register names for documentation
Allow configuration programming in non-paranoid mode
Add support for value filter for a couple of registers already
programmed in other part of the kernel
v9: Documentation fix (Lionel)
Allow writing WAIT_FOR_RC6_EXIT only on Gen8+ (Andrzej)
v10: Perform read access_ok() on register pointers (Lionel)
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Reviewed-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170803165812.2373-2-lionel.g.landwerlin@intel.com
* Don't define it twice.
* Define MSBs first, like the rest of i915_reg.h.
* Add CNL_ prefix to the bit that arrived in CNL.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170714175228.27019-1-paulo.r.zanoni@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get HDMI YCBCR420 output, the PIPEMISC register should be
programmed to:
- Generate YCBCR output (bit 11)
- In case of YCBCR420 outputs, it should be programmed in full
blend mode to use the scaler in 5x3 ratio (bits 26 and 27)
This patch:
- Adds definition of these bits.
- Programs PIPEMISC for YCBCR420 outputs.
- Adds readouts to compare HW and SW states.
V2: rebase
V3: rebase
V4: rebase
V5: added r-b from Ander
V6: Handle only YCBCR420 outputs (ville)
V7: rebase
V8: Addressed review comments from Ville
- Add readouts for state->ycbcr420 and 420 pixel_clock.
- Handle warning due to mismatch in clock for ycbcr420 clock.
- Rename PIPEMISC macros to match the Bspec.
- Add a debug print stating if YCBCR 4:2:0 output enabled.
Added r-b from Ville
V9: Addressed review comments from Imre:
- Add 420 mode clock adjustment in intel_hdmi_mode_valid to
prevent 420_only modes getting rejected for high clock.
- Add port clock adjustment for ycbcr420 modes in ddi_get_clock
- Rename macros as per Ville's suggestion.
- Remove unnecessary wl changes.
V10: Added r-b from Imre
V11: Fixed faulty dotclock handling, and addressed missing comment
from previous set of review comments (Imre)
V12: Fixed dotclock for 12bpc too, removed 420 check for GEN < 10
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500904172-31717-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pattern of a power well backing a set of fuses whose initialization
we need to wait for during power well enabling is common to all GEN9+
platforms. Adding support for this to the HSW power well enable helper
allows us to use the HSW/BDW power well code for GEN9+ as well in a
follow-up patch.
v2:
- Use an enum for power gates instead of raw numbers. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-6-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although on HSW/BDW there is only a single display global power well,
it's programmed the same way as other GEN9+ power wells. This also
means we can get at the HSW/BDW request and status flags the same way
it's done on GEN9+ by assigning the corresponding HSW/BDW power well ID.
This ID was assigned in a recent patch, so we can now switch to using
the same macros everywhere on HSW+.
Updating the HSW power well control register with RMW is not strictly
necessary, but this will allow us to use the same code for GEN9+.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-13-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an ID for the HSW/BDW global display power well for consistency. The
ID is selected so that it can be used to get at the HW request and
status flags with the corresponding GEN9+ macros. Unifying the HSW/BDW
and GEN9+ versions of these macros and the power well ops using them
will be done in follow-up patches.
v2:
- Rebased on v2 of patch 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-3-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the I830 power well ID assignment explicit for consistency.
v2:
- s/GEN2/I830/ in the comment, since other GEN2s don't have the power
well. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-2-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, the power well IDs are defined in separate platform specific enums,
which isn't ideal for the following reasons:
- the IDs are used by helpers like lookup_power_well() in a platform
independent way
- the always-on power well is used by multiple platforms and so needs
now separate IDs, although these IDs refer to the same thing
To make things more consistent use a single enum instead of the two
separate ones, listing the IDs per platform (or set of very similar
platforms like all GEN9/10). Replace the separate always-on power
well IDs with a single ID.
While at it also add a note clarifying the distinction between regular
power wells that follow a common programming pattern and custom ones
that are programmed in some other way. The IDs for regular power wells
need to stay fixed, since they also define the request and state HW flag
positions in their corresponding power well control register(s).
v2:
- Add comment about id to req,status bit mapping to the enum. (Rodrigo)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power well IDs are used for lookup, so they must be unique on a
given platform; ensure this on CHV. This didn't cause an actual problem
since we didn't need to look up power wells which happened to share an
ID.
Mark this new power well as custom, since its programming pattern
doesn't follow that of the rest of VLV/CHV power wells.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-2-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
v2: Mika pointed out that 24 was hardcoded while it
should consider ref clock that can be either 24KHz
or 19.2KHz on CNL.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499374321-31152-1-git-send-email-rodrigo.vivi@intel.com
The Cursor Coeff is lower 6 bits in the PORT_TX_DW4 register
and hence the CURSOR_COEFF_MASK should be (0x3F << 0)
Fixes: 04416108cc ("drm/i915/cnl: Add registers related to voltage
swing sequences.")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498785241-21138-1-git-send-email-manasi.d.navare@intel.com
Paulo noticed that we were missing few bits clear
before writing values back to the register on
these RMW MMIO operations.
v2: Remove "POST_" from CURSOR_COEFF_MASK. (Paulo).
v3: Remove unnecessary braces. (Jani).
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497897572-22520-1-git-send-email-rodrigo.vivi@intel.com
Enables access to OA unit metrics for BDW, CHV, SKL and BXT which all
share (more-or-less) the same OA unit design.
Of particular note in comparison to Haswell: some OA unit HW config
state has become per-context state and as a consequence it is somewhat
more complicated to manage synchronous state changes from the cpu while
there's no guarantee of what context (if any) is currently actively
running on the gpu.
The periodic sampling frequency which can be particularly useful for
system-wide analysis (as opposed to command stream synchronised
MI_REPORT_PERF_COUNT commands) is perhaps the most surprising state to
have become per-context save and restored (while the OABUFFER
destination is still a shared, system-wide resource).
This support for gen8+ takes care to consider a number of timing
challenges involved in synchronously updating per-context state
primarily by programming all config state from the cpu and updating all
current and saved contexts synchronously while the OA unit is still
disabled.
The driver intentionally avoids depending on command streamer
programming to update OA state considering the lack of synchronization
between the automatic loading of OACTXCONTROL state (that includes the
periodic sampling state and enable state) on context restore and the
parsing of any general purpose BB the driver can control. I.e. this
implementation is careful to avoid the possibility of a context restore
temporarily enabling any out-of-date periodic sampling state. In
addition to the risk of transiently-out-of-date state being loaded
automatically; there are also internal HW latencies involved in the
loading of MUX configurations which would be difficult to account for
from the command streamer (and we only want to enable the unit when once
the MUX configuration is complete).
Since the Gen8+ OA unit design no longer supports clock gating the unit
off for a single given context (which effectively stopped any progress
of counters while any other context was running) and instead supports
tagging OA reports with a context ID for filtering on the CPU, it means
we can no longer hide the system-wide progress of counters from a
non-privileged application only interested in metrics for its own
context. Although we could theoretically try and subtract the progress
of other contexts before forwarding reports via read() we aren't in a
position to filter reports captured via MI_REPORT_PERF_COUNT commands.
As a result, for Gen8+, we always require the
dev.i915.perf_stream_paranoid to be unset for any access to OA metrics
if not root.
v5: Drain submitted requests when enabling metric set to ensure no
lite-restore erases the context image we just updated (Lionel)
v6: In addition to drain, switch to kernel context & update all
context in place (Chris)
v7: Add missing mutex_unlock() if switching to kernel context fails
(Matthew)
v8: Simplify OA period/flex-eu-counters programming by using the
batchbuffer instead of modifying ctx-image (Lionel)
v9: Back to updating the context image (due to erroneous testing,
batchbuffer programming the OA unit doesn't actually work)
(Lionel)
Pin context before updating context image (Chris)
Drop MMIO programming now that we switch to a kernel context with
right values in initial context image (Chris)
v10: Just pin_map the contexts we want to modify or let the
configuration happen on first use (Chris)
v11: Update kernel context OA config through the batchbuffer rather
than on the fly ctx-image update (Lionel)
v12: Rework OA context registers update again by swithing away from
user contexts and reconfiguring the kernel context through the
batchbuffer and updating all the other contexts' context image.
Also take care to lock slice/subslice configuration when OA is
on. (Lionel)
v13: Request rpcs updates on all engine when updating the OA config
(Lionel)
v14: Drop any kind of rpcs management now that we monitor sseu
configuration changes in a later patch (Lionel)
Remove usleep after programming the NOA configs on Gen8+, this
doesn't seem to be needed (Lionel)
v15: Respect coding style for block comments (Chris)
v16: Add missing i915_add_request() in case we fail to emit OA
configuration (Matthew)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com> \o/
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.
v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com
This are the registers and bits needed for the voltage swing
sequence on Cannonlake.
v2: Remove CL_DW5 that was wrongly defined.
v3: Use (1 << 1) instead of (1<<1) as Paulo suggested
Change DW2 swing sel upper and lower macros to do the
bit selection instead of definint a table that doesn't
match the spec. It is based on a Manasi version of it.
Credits-to: Manasi.
v4: Let SCALING_MODE_SEL flexible. (Manasi)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-9-git-send-email-rodrigo.vivi@intel.com
Also new registers can have different mmio offsets
per different lane per port.
v2: Use _PICK as PORT3 instead of creating a new
macro with if per port.
v3: Use _PICK directly on MMIO_PORT6. While MMIO_PORT
isn't flexible enough let's continue with MMIO_PORT6
as we have MMIO_PORT3.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-8-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Although CNL follows PLL initialization more like Skylake
than Broxton we have a completely different initialization
sequence and registers used.
One big difference from SKL is that CDCLK PLL is now
exclusive (ADPLL) and for DDIs and MIPI we need to use
DFGPLLs 0, 1 or 2.
v2: Accept all Ander's suggestions and fixes:
- Registers and bits names prefix
- Group pll functions
- bits masks fixes
- remove read and modify on cfgcr1
- fix cfgcr0 setup
v3: Set SSC_ENABLE for DP.
Fix HDMI_MODE cfgcr0.
Avoid touch cfgcr0 on DP.
Add missed else on dpll_mgr definition so we use cnl one, not hsw.
v3: Centra freq should be always set to default and change bits
definitions to (1 << 1) instead of (1<<1). (by Paulo)
v4: Rebased.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-7-git-send-email-rodrigo.vivi@intel.com
One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.
So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.
v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
so we were disabling interrupts.
Credits-to: Clinton
Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
and clock on in 2 separated reg writes. (Paulo)
Also update bits definitions to use space
(1 << 1) instead of (1<<1). (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com
Implement the CNL display init/uninit sequence as outlined in Bspec.
Quite similar to SKL/BXT. The main complicaiton is probably the extra
procmon setup we must do based on the process/voltage information we
can read out from some register.
v2: s/skl_dbuf/gen9_dbuf/ to follow upstream
bxt needed a cdclk sanitize step, so let's add it for cnl too
v3: s/CHICKEN_MISC_1/CHICKEN_MISC_2/ (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework
v5: Removed unecessary Aux IO forced enable/disable, Fix DW10 setup
Fix procpon Mask. (Credits-to Paulo and Clint)
Remove A0 workaround.
v6: Rebased on top of recent code (Rodrigo).
v7: Respect the order of sanitize_ after set_
(Done by Rodrigo, Requested by Ville)
v8: Commit message updated to matvh v5 changes besides
Remove unused DW8 and an extra blank line. (all noticed
by Imre).
v9: Remove __attribute__((unused)) added on latest version
of drm/i915/cnl: Implement .set_cdclk() for CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-3-git-send-email-rodrigo.vivi@intel.com
Add support for reading out the cdclk frequency from the hardware on
CNL. Very similar to BXT, with a few new twists and turns:
* the PLL is now called CDCLK PLL, not DE PLL
* reference clock can be 24 MHz in addition to the 19.2 MHz BXT had
* the ratio now lives in the PLL enable register
* Only 1x and 2x CD2X dividers are supported
v2: Deal with PLL lock bit the same way as BXT/SKL do now
v3: DSSM refclk indicator is bit 31 not 24 (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework.
v5: Set cdclk to the ref clock as previous platforms. (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-1-git-send-email-rodrigo.vivi@intel.com
Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com
CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.
Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.
v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
for the same reasons as v4 when we found out that current CNL
SKUs don't have the full port E split.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com
José Roberto de Souza